Series M Miniature Rockers s e gl g General Specifications o T s ker B Electrical Capacity (Resistive Load) c o R Power Level (silver): 6A @ 125V AC & 3A @ 250V AC 4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits s on Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum utt (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) b h s Logic/Power Level (gold over silver): Combines silver & gold ratings u P Note: Find additional explanation of dual rating & operating range in Supplement section. B P ed Other Ratings at n mi Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold u Ill Insulation Resistance: 1,000 megohms minimum @ 500V DC e Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; bl ma 1,500V AC minimum between contacts and case for 1 minute minimum m a Mechanical Life: 50,000 operations minimum gr o Electrical Life: 25,000 operations minimum for silver; 50,000 operations minimum for gold; Pr 50,000 operations minimum for silver at 3A @ 125V AC s Angle of Throw: 25° k c o eyl Materials & Finishes K Actuator Clip & Mounting Frame: Stainless Steel Body Frame: Stainless steel s arie Case: Diallyl phthalate resin (UL94V–0) ot Movable Contactor: Phosphor bronze with silver or gold plating R Movable Contacts: Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Stationary Contacts: Silver with silver plating (code W); copper or brass with gold plating (code G); s or silver with gold plating (code A) e Slid Terminals: Copper or brass with silver plating; or copper or brass with gold plating Environmental Data Operating Temp Range: –30°C through +85°C (–22°F through +185°F) s e ctil Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) Ta Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Tilt Processing Soldering: Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. h c Manual Soldering for Silver: See Profile B in Supplement section. u o T Note: Actuator must be in OFF (center) position while soldering. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. s or Standards & Certifications at c di Flammability Standards: UL94V–0 for case n I UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL ” before first dash in part number to order UL recognized switch. s e ori All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum. ss CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. e cc Add “/C” before first dash in part number to order CSA certified switch. A All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum. nt e m e pl p u S B62 www.nkkswitches.com 3/13/17

Series M Miniature Rockers s e gl Distinctive Characteristics g o T s B ker c o R Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PCB. s n o utt b High insulating barriers increase isolation of circuits in multipole devices sh u P and provide added protection to contact points. B P d e The molded diallyl phthalate case has a UL 94V-0 nat mi flammability rating. u Ill e bl a Epoxy sealed terminals prevent entry of solder flux m m and other contaminants. gra o Pr Prominent external insulating barriers increase s k insulation resistance and dielectric strength. oc yl e K Bias guard prevents misalignment of contacts; interlocking of actuator block with rocker and es internal guide does not allow transmission of ari ot R diagonal force on rocker to reach contact mechanism. s e d Clinching of the frame to the case well above the base Sli and terminals provides 1,500V dielectric strength. s e ctil a T Tilt Actual Size h Snap-in Mount Page B64 uc o T s or at c di n Bracket PC Mount Page B72 I s e ori s s e c c A Flat Frame Mount Page B83 nt e m e pl p u S www.nkkswitches.com B63

Series M Snap-In Mount Miniature Rockers s e gl TYPICAL SWITCH ORDERING EXAMPLE g o T s M20 1 2 TJ W 01 F C ker B c o R s n o butt Poles Rockers & Paddles h s Pu 1 SPDT F .450” (11.43mm) Wide Rocker ed PB 2 DSPP3DTT Mounting Frame Terminals G .450” (11.43mm) Wide Paddle nat TJ Snap-in Frame 01 Solder Lug S .453” (11.5mm) False mi Illluminated Rocker in Black only Illu 02 Quick Connect able 03 .250” (6.35mm) m Straight PC m a Circuits ogr 05 .425” (10.8mm) Rocker & Paddle Pr 2 ON NONE ON Wirewrap Colors ks 3 ON OFF ON 06 .750” (19.05mm) A Black c Wirewrap ylo 5 ON NONE (ON) B White Ke 8 (ON) OFF (ON) 07 .964” (24.5mm) C Red Wirewrap 9 ON OFF (ON) E Yellow 1.062” (27.0mm) aries *4 ON ON ON 08 Wirewrap F Green Rot *6 (ON) ON (ON) G Blue *7 ON ON (ON) H Gray s ( ) = Momentary e Contact Materials & Ratings d Sli *3-ON circuits Silver; Rated W 6A @ 125V AC & 3A @ 250V AC s Gold; Rated e G ctil 0.4VA max @ 28V AC/DC max a T Gold over Silver; Rated A 6A @ 125V AC & 0.4VA max @ 28V AC/DC max Tilt h c DESCRIPTION FOR TYPICAL ORDERING EXAMPLE u o T M2012TJW01-FC-1A s or at Red .450” (11.43mm) c di Wide Rocker n I Black Bezel without LED es SPDT ori ON-NONE-ON Circuit Snap-in Frame s s e c Ac Silver Contacts with 6–Amp Rating nt Solder Lug Terminals e m e pl p u S B64 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e TYPICAL SWITCH ORDERING EXAMPLE gl g o T 1 A s B ker c o R s n o Optional Bezels Bezel Colors LED Colors butt h s u P 1 Bezel without LED A Black B P d B White e at n E Yellow mi u F Green Ill e bl G Blue a m m H Gray a gr o Pr s k 2 Bezel with 1 Round LED A Black 1 LED c o yl C Red Ke F Green s e ari 3 Bezel with 2 Round LEDs A Black 2 LEDs ot R Bezel with 2 Rectangular Top LED Bottom LED 4 LEDs C Red C Red s e d E Yellow E Yellow Sli F Green F Green s e IMPORTANT: ctil a T Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Tilt h DESCRIPTION FOR TYPICAL ORDERING EXAMPLE c u o T M2012TJW01-FC-3A-CF s or Red .450” (11.43mm) cat Wide Rocker Top LED Red ndi I Bottom LED Green Snap-in Frame s e SPDT ON-NONE-ON Circuit Black Bezel with ori 2 Round LEDs ss Silver Contacts with e c c 6–Amp Rating A Solder Lug Terminals nt e m e pl p u S www.nkkswitches.com B65

Series M Snap-In Mount Miniature Rockers s e gl POLES & CIRCUITS g o T Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics s Down Center Up Down Center Up ker B Note: Terminal numbers are not c Pole Model Ro actually on the switch. ns M2012 ON NONE ON SPDT o utt M2013 ON OFF ON 2 (COM) b h SP M2015 ON NONE (ON) 2-3 OPEN 2-1 s Pu M2018 (ON) OFF (ON) 3 1 B M2019 ON OFF (ON) P d ate M2022 ON NONE ON DPDT n mi M2023 ON OFF ON u 2 (COM) 5 Ill DP M2025 ON NONE (ON) 2-3 5-6 OPEN 2-1 5-4 ble M2028 (ON) OFF (ON) 3 1 6 4 a m M2029 ON OFF (ON) m a ogr For 3 Throw (3-On) Pr Connected Terminals & Schematic s ck Pole Model Down Center Up External Connection o yl e M2024 ON ON ON The SP3T model utilizes a double pole K SP M2026 (ON) ON (ON) base. M2027 ON ON (ON) s (out) arie ConExnteecrntioanl ConExnteecrntioanl ConExnteecrntioanl Ecoxntenrencatli on External 6 3 Rot 2 (in) 5 2 (in) 5 2 (in) 5 must be made Conn 5 2 C(ino)mmon during field 4 1 installation. 1 (out) 34 (out) 6 (out) 1 (out) 34 (out) 6 (out) 1 (out) 3 4 (out)6 (out) (out) (out) s e 2-3 5-6 2-3 5-4 2-1 5-4 d Sli MOUNTING FRAME s ctile TJ Snap-in Frame Panel Cutout for Panel Cutout for a T Single Pole (15.9) Double Pole (15.9) .626 .626 without Bezel without Bezel Tilt ( 1.781.00) 25° (.1429.25) .(1531.61) (2.54) Dia .100 Panel Thickness without Bezel: .039” ~ .126” (1.0mm ~ 3.2mm) (12.2) (4.3) .480 .170 Panel Thickness with Bezel: .039” ~ .098” (1.0mm ~ 2.5mm) h c u o T CONTACT MATERIALS & RATINGS s W or Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC at c di n I G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum s e ori Note: See Supplement section to find complete explanation of operating range. s s e c c A A Power Level 6A @ 125V AC Gold over Silver or Logic Level or 0.4VA maximum @ 28V AC/DC maximum nt e m e Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the ppl same application. See Supplement section to find complete explanation of dual rating and operating range. u S B66 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e TERMINALS gl g o T .062” (1.57mm) Wide 01 02 Solder Lug Quick Connect Epoxy Seal (.415.07) Epoxy Seal (6.2.3550) B ckers o (2.0) (2.0) R .079 (1.1) .079 (1.57) .043 .062 T h k = .(003.81) T h k = .(003.81) ons utt b h (4.8) s 03 .250” (6.35mm) .189 Pu Straight PC 3 3 6 (4.7) Typ (4.7) Typ B Epoxy Seal (4.8) (.62.5305) 2.185 2 5 .185 d P .189 e 1 1 4 at n (1.17) (1.8) Dia Typ mi .046 .073 (1.8) Dia Typ u Thk = (0.8) .073 Ill .031 e Single Pole Double Pole bl a m m a 05 .425” (10.8mm) gr o Wirewrap or Extended PC Pr If using as extended PC terminal, refer to 06 .750” (19.05mm) Epoxy Seal the above footprints. cks Wirewrap or Extended PC A ylo e K .964” (24.5mm) Dimension A = terminal lengths as shown 07 Wirewrap or Extended PC (1.27) beside the terminal codes Thk = (0.8) .050 at the left. es 08 1.062” (27.0mm) .031 ari Wirewrap or Extended PC ot R ROCKERS & PADDLES s e d Sli AT4150 AT4151 F G .450” (11.43mm) .450” (11.43mm) Wide Rocker Wide Paddle (2.36) .093 s Material: Polyamide (.93.6192) (1.41.5403) Material: Polyamide (16.36) Tactile Finish: Matte Finish: Matte .644 (7.11) (5.84) R (6.3).280 .230 .248 Colors Available: Colors Available: A, B, C, E, F, G, H (1.8) A, B, C, E, F, G, H (1.41.5403) .(01.781) Tilt .071 (11.8) (11.8) .465 .465 h c u o AT466 .453” (11.5mm) T S False Illuminated Rocker Rocker False Illuminator .(383.69) (.1414.35) ors at c Material: Polycarbonate Acrylonitrile Butadiene Styrene (7.7) di .303 n Finish: Glossy I Colors: Black White and Red (.1415.53) (11.8) .(017.81) ories .465 ss e When a bezel is selected with AT466, glossy polycarbonate AT207 is supplied. c c A Cap Colors A B C E F G H ment Available: Black White Red Yellow Green Blue Gray e pl p u S www.nkkswitches.com B67

Series M Snap-In Mount Miniature Rockers s e gl OPTIONAL SNAP-IN BEZELS & BEZEL COLORS g o T 1 AT2107 Bezel kers B (11.8) A Black F Green ((..11665522..9966)) oc Material: Polyamide .465 R (2.2) B G Finish: Matte .087 White Blue A s n (12.0) utto (1.651.64) .472 Single Pole Double Pole b (21.5) E H sh .846 Yellow Gray (12.5)mm (13.1)mm Pu A .492” .516” B P d e at AT208 Bezel n 2 A mi for AT070 LED Black B (8.8) Dia Illu .346 mable MPoalytecrairabl:o nate (.1794.80) (13.5) (.1416.85) .(028.27) LoEnD n ceoxlto pras g&e .specifications m .531 (13.8) a .543 gr Single Pole Double Pole Pro Finish: Glossy (.1427.20) (12.5)mm (13.1)mm (.1652.96) A Keylocks Cfoor nmtaacttt ef aficntoisrhy. (.1651.46)(5.4) Dia ( 3 10.1.92) B (6...42294526)m””m (6...52515568)m””m A .213 aries 3 AfoTr2 A1T26 B1e7z LeElD A Black Rot (10.0) (.1427.20) (.1652.96) Material: .394 Polycarbonate (2.2) LED colors & .087 es (7.8) specifications A Slid Finish: .3(101.78) on next page. Semi-glossy (8.0) .465(.2814.65) Sq Single Pole Double Pole .315 (3.0) Dia Typ (18.4)mm (18.7)mm .118 A s .724” .736” e ctil a T 4 AT213 Bezel A for AT618 LED Black (10.0) (12.0) (15.9) .394 .472 .626 Tilt MPoalytecrairabl:o nate (.20.709) Typ .(028.27) LED colors & (7.8) specifications A .307 Finish: (11.8) on next page. .465 Single Pole Double Pole Touch Semi-glossy (.83.105) (.519.07) Typ (.2814.65) Sq A (18.4)mm (18.7)mm .724” .736” s Bezel Assembly or at dic 1. Pry out tab on bezel to 2. Insert switch frame under 3. Push tab back into place. 4. Snap assembled bezel n I a 45° angle. tab and snap on bezel. and switch into panel. s e ori Tab 45° s s e c c A Tab nt e m e pl p u S B68 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e LED COLORS & SPECIFICATIONS gl g o T Bezel Orientation on Switch AFoTr0 7Be0z LeEl DAT208 AFoTr6 1Be7z LeEl DAT212 AFoTr6 1Be8z LeEl DAT213 B ckers o with 1 LED (5.08) Dia with 2 Round LEDs (3.0) Dia with 2 Rectangular LEDs (5.0) R .200 .118 .197 (7.7) (5.0) (7.0) ns .303 .197 .276 o utt Top LED Top LED b de de de sh Circuit Mark This Si Bottom LED Circuit Mark This Si (+) (-) Bottom LED Circuit Mark This Si (-) Puuminated PB (+) Ill (-) e bl (+) a m m a Note: Lead lengths may differ from manufacturing lot to lot. The longer lead is the anode (+). gr o Pr AT070 AT617 AT618 s k c o C F C E F C E F yl (+) (-) e K Color Red Green Red Yellow Green Red Yellow Green Maximum Forward Current I 25mA 50mA 30mA 30mA 25mA 25mA 30mA 25mA es FM ari Typical Forward Current I 20mA 30mA 20mA 20mA 20mA 20mA 20mA 20mA ot F R Forward Voltage V 2.8V 2.1V 2.0V 2.1V 2.25V 2.25V 2.1V 2.2V F Maximum Reverse Voltage V 4V 5V 5V 5V 5V 5V 5V 5V RM es d Current Reduction Rate 0.33 0.40 0.40 0.40 0.33 0.33 0.40 0.33 Sli Above 25°C ∆I mA/°C mA/°C mA/°C mA/°C mA/°C mA/°C mA/°C mA/°C F Ambient Temperature Range –10° ~ +70°C –15° ~ +70°C –25° ~ +70°C (when used with a bezel) es ctil a T The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is independent of switch operation. LED is colored in OFF state. If the source voltaTghee ibs aglrlaesatt erer stihsatonr tchael crualtaetdio vno altangde m oofr teh ela LmEpD ,d ae tabial lalarset srhesoiwstno ri nm tuhset bSeu pcpolnenmeecntet ds eicnt isoenr.i es with the lamp. Tilt LEGENDS h c u o T NKK Switches can provide custom legends for caps. Contact factory for more information. s or Suggested Printable Area for Cap at c di n (0.38) Typ I .015 (4.5) Typ es OFFON .177 ssori Recommended Print Method: (0.76) Typ (9.91) (0.76) Typ (3.36) Typ e .030 .390 .030 .132 cc (11.43) A Pad Print .450 nt e m Epoxy based ink is recommended. AT4150 Shaded areas are printable areas. e pl p u S www.nkkswitches.com B69

Series M Snap-In Mount Miniature Rockers s e gl TYPICAL SWITCH DIMENSIONS g o T Snap-in Frame • Solder Lug Single Pole s ker B (.419.94) . 0(14.13) xx (.20.709) Typ oc (2.8) Circuit Mark R .110 This Side ns (4.7) Typ 3 utto (.1780.09) 25° .185 2 (.1531.20) hb (0.8) Typ 1 s .031 u P PB (11.43) (0.5) (0.5) (2.0) Typ d .450 .020 .020 .079 nate (.1428.20) (.313.30) .(277.19) (.93.741) (.417.57) (.73.191) mi u M2012TJW01-FC Ill e bl Snap-in Frame • Solder Lug Double Pole a m m a gr (4.9) (1.1) x (2.0) Typ (4.8) Pro .194 (2.8) Circuit Mark .043 x .079 .189 .110 This Side s k c o 6 3 yl (4.7) Typ Ke (.1780.09) 25° .185 5 2 (.1531.20) (0.8) Typ .031 4 1 s e otari (1.41.5403) .(002.50) .(002.50) (.20.709) Typ R (12.2) (3.3) (7.1) (9.4) (4.5) (12.7) .480 .130 .279 .371 .177 .500 M2022TJW01-FC s e d Sli Snap-in Frame • Solder Lug Single Pole (2.8) Circuit Mark (1.1) x (2.0) Typ .110 This Side .043 x .079 s e ctil 3 Ta (4.7) Typ (.1780.09) 25° .185 2 (.1531.20) (0.8) Typ 1 .031 Tilt (11.43) (2.0.3963) (3.18) (0.5) (0.5) (2.0) Typ .450 .125 .020 .020 .079 (12.2) (13.7) (7.1) (9.4) (4.5) (7.9) .480 .539 .279 .371 .177 .311 h M2012TJW01-GC c u o T Snap-in Frame • Solder Lug Double Pole s cator (.211.80) CThiricsu Sitid Meark .(014.13) xx (.20.709) Typ (.418.89) di n I 6 3 (4.7) Typ ssories (.1780.09) 25° (.00..31881) 5Typ 45 12 (.1531.20) e c (2.36) Ac .093 (11.43) (3.18) (0.5) (0.5) (2.0) Typ .450 .125 .020 .020 .079 nt (12.2) (13.7) (7.1) (9.4) (4.5) (12.7) me .480 .539 .279 .371 .177 .500 e pl p M2022TJW01-GC u S B70 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e TYPICAL SWITCH DIMENSIONS gl g o T Single & Double Pole Snap-in Frame • AT2107 Bezel • Solder Lug (5.6) (1.1) x (2.0) Typ (4.8) s .221 Circuit Mark .043 x .079 .189 B ker This Side oc R 3 6 3 (12.0) (4.7) Typ (13.0) (13.0) (21.5).472 25° .185 2 .512(14.0) 5 2 .512(14.0) ns .846 (.00.381) Typ 1 .551 4 1 .551 butto h s u P (11.43) (4.3) .450 .169 B (.1416.85) .(028.27) .(002.50) (.20.709) (.20.709) Typ ed P (15.6) (4.01) (6.4) (9.4) (4.5) (7.9) (12.7) at .614 .158 .252 .371 .177 .311 .500 M2012TJW01-FC-1A min u Ill Double Pole Snap-in Frame • AT208 Bezel • Solder Lug ble a m (4.9) (15.3) Min (2.5) m .193 .602 (0.61) Sq .098 gra .024 Pro (5.08) Dia .200 (19.0) .748 CThiricsu Sitid Meark .(014.13) xx .(027.09) Typ ks (13.109.20) (1.533.51) (4.7) Typ 6 3 (13.0) eyloc (.1427.02) 25° .185 5 2 .512(14.0) K (0.8) Typ 4 1 .551 .031 s e (4.3) ari (1.41.540(31)1.8) (2.1.629) (0.5) (4.8) .(027.09) Typ Rot .465 .087 .020 .189 (15.6) (4.01) (6.4) (9.4) (4.5) (12.7) .614 .158 .252 .371 .177 .500 M2022TJW01-FC-2A-C s e d Single Pole Snap-in Frame • AT212 Bezel • Solder Lug Sli (10.0) (7.8) (5.6) (1.1) x (2.0) Typ .394 .307 .221 .043 x .079 Circuit Mark This Side s e 3 ctil (4.7) Typ (13.0) a (.83.105) (.1427.02) 25° .185 2 .512(14.0) T (0.8) Typ 1 .551 .031 (3.0) Dia Typ .118 (11.43) (4.3) Tilt .450 .169 (11.8) (2.2) (0.5) (2.0) .465 .087 .020 .079 (21.5) Sq (4.01) (6.4) (9.4) (4.5) (7.9) .846 .158 .252 .371 .177 .311 M2012TJW01-FC-3A-CF h c u o Double Pole Snap-in Frame • AT213 Bezel • Solder Lug T (10.0) (7.8) (5.6) (1.1) x (2.0) Typ .394 .307 .221 Circuit Mark .043 x .079 ors This Side at c 6 3 ndi (4.7) Typ (13.0) I (.83.105) (.1427.02) 25° .185 5 2 .512(14.0) (.00.381) Typ 4 1 .551 ories (5.0) Typ ss .197 e c (2.0) (11.43) (4.3) (0.5) (2.0) Typ Ac .079 .450 .169 .020 .079 (11.8) (2.2) (4.8) .465 .087 .189 nt (21.5) Sq (4.01) (6.4) (9.4) (4.5) (12.7) e .846 .158 .252 .371 .177 .500 em pl M2022TJW01-FC-4A-CF p u S www.nkkswitches.com B71

Series M Bracket PC Mount Miniature Rockers s e gl TYPICAL SWITCH ORDERING EXAMPLE g o T s M20 1 3 TX G ker B c o R s n o utt b sh Poles Mounting Frames u P 1 SPDT Narrow Frame B TX d P DPDT for Small Actuator ate 2 SP3T Wide Frame min TZ for Large Actuator u 3PDT (used only Ill with terminal codes able 3 30 & 41 & frame m m code TX) a ogr 4PDT Pr DP3T 4 (used only with ks Circuits Contact Materials & Ratings c terminal code 41 & o Keyl frame code TX) 2 ON NONE ON W Silver; Rated 6A @ 125V AC & 3A @ 250V AC 3 ON OFF ON Gold; Rated es 5 ON NONE (ON) G 0.4VA max @ 28V AC/DC max ari 8 (ON) OFF (ON) ot Gold over Silver; Rated R 9 ON OFF (ON) A 6A @ 125V AC & 0.4VA max @ *4 ON ON ON 28V AC/DC max des *6 (ON) ON (ON) Sli *7 ON ON (ON) ( ) = Momentary es *3-ON circuits ctil a T Tilt h c ou DESCRIPTION FOR TYPICAL ORDERING EXAMPLE T M2013TXG41-DC s or at c di SPDT n I ON-OFF-ON Circuit Gold Contacts with s e ori 0.4VA Rating ss TX Frame with .365” (9.27mm) e cc Wide Red Rocker .150” (3.81mm) A Vertical PC Terminals with Support nt e m e pl p u S B72 www.nkkswitches.com

Series M Bracket PC Mount Miniature Rockers s e TYPICAL SWITCH ORDERING EXAMPLE gl g o T 41 D C s B ker c o R s n o utt b Terminals For Rockers Rocker & Paddle sh u TX & TZ Frames & Paddles Colors P B Straight PC with Bracket Small Actuators A Black d P (1-2 Pole only) (TX Frame) B White nate .250” (6.35mm) Straight PC with .365” (9.27mm) mi 13 .465” (11.8mm) Bracket D Wide Rocker C Red Illu 15 .425” (10.8mm) Straight PC with E .365” (9.27mm) E Yellow mable .630” (16.0mm) Bracket Wide Paddle F Green m a 17 .19.6145”0 ”( 2(42.95.m2mmm) )S tBrraaigckhet tPC with F .W45id0e” R(1o1ck.4e3rmm) G Blue Progr H Gray Straight PC with Reinforced Bracket G .450” (11.43mm) cks (1-2 Pole only) Wide Paddle o yl e .250” (6.35mm) Straight PC with Large Actuators K 23 .465” (11.8mm) Bracket (TZ Frame) 25 ..462350”” ((1106..80mmmm)) SBrtraacikgehtt PC with J .W59id5e” R(1o5ck.1e1rmm) aries ot .750” (19.05mm) Straight PC with .595” (15.11mm) R 26 H .953” (24.2mm) Bracket Wide Paddle s e d Terminals For Sli TX Frame Only Right Angle PC with Support IMPORTANT: s (1-3 Pole only) Switches are supplied without UL & CSA marking unless specified. ctile 30 .150” (3.81mm) Right Angle PC UL & CSA recognized only when ordered with marking on the switch. Ta Specific models, ratings and ordering instructions are noted on the Vertical PC with Support General Specifications page. (1-4 Pole) 41 .150” (3.81mm) Vertical PC Tilt h c DESCRIPTION FOR TYPICAL ORDERING EXAMPLE ou T M2022TZG23-JC s or at c TZ Frame with .595” (15.11mm) ndi I Wide Red Rocker s e ori Gold Contacts with 0.4VA Rating s DPDT es c ON-NONE-ON Circuit Ac .250” (6.35mm) Straight PC Terminals nt with Reinforced Bracket e m e pl p u S www.nkkswitches.com B73

Series M Bracket PC Mount Miniature Rockers s e gl POLES & CIRCUITS g o T Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics s ker B Down Center Up Down Center Up Note: Terminal numbers are not actually c o R on the switch. Pole Model * Reverse circuits available for vertical s mount SP & DP upon request. n o utt b sh M2012 ON NONE ON SPDT u P M2013 ON OFF ON PB SP *M2015 ON NONE (ON) 2-3 OPEN 2-1 2 (COM) nated *MM22001189 (OONN ) OOFFFF ((OONN)) 3 1 mi u Ill M2022 ON NONE ON DPDT e bl M2023 ON OFF ON ma DP *M2025 ON NONE (ON) 2-3 5-6 OPEN 2-1 5-4 2 (COM) 5 m gra M2028 (ON) OFF (ON) 3 1 6 4 Pro *M2029 ON OFF (ON) ks M2022 ON NONE ON 3PDT c o M2023 ON OFF ON yl 2-3 5-6 2-1 5-4 Ke 3P *M2025 ON NONE (ON) OPEN 2 5 (COM) 8 8-9 8-7 M2028 (ON) OFF (ON) 3 1 6 4 9 7 *M2029 ON OFF (ON) s e otari M2042 ON NONE ON 4PDT R M2043 ON OFF ON 2-3 5-6 2-1 5-4 4P *M2045 ON NONE (ON) OPEN 2 5 (COM) 8 11 8-9 11-12 8-7 11-10 M2048 (ON) OFF (ON) s 3 1 6 4 9 7 12 10 de *M2049 ON OFF (ON) Sli For 3 Throw (3-On) s Connected Terminals & Schematics e ctil a Pole Model Down Center Up Down Center Up T External External External Connection Connection Connection Tilt SP MM22002246 (OONN) OONN (OONN) 2 (in) 5 2 (in) 5 2 (in) 5 M2027 ON ON (ON) 1 (out) 34 (out) 6 (out) 1 (out) 34 (out) 6 (out) 1 (out) 34 (out)6 (out) 2-3 5-6 2-3 5-4 2-1 5-4 h c u External External External External External External To Connection Connection Connection Connection Connection Connection 2 (in) 5 8 (in) 11 2 (in) 5 8 (in) 11 2 (in) 5 8 (in) 11 M2044 ON ON ON DP M2046 (ON) ON (ON) ors M2047 ON ON (ON) 1 (out) 34 (out)6 (out)7 (out)910 (out)12 (out) 1 (out) 34 (out)6 (out)7 (out)910 (out) 12 (out) 1 (out) 34 (out)6 (out)7 (out)910 (out)12 (out) at dic 2-3 5-6 2-3 5-4 2-1 5-4 n 8-9 11-12 8-9 11-10 8-7 11-10 I s e The SP3T model utilizes a The DP3T model utilizes a sori double pole base. (out) four pole base. (out) (out) es External 6 3 External cc Conn Conn 12 9 6 3 Common Aement Emxatedren adlu crionngn fiecetlido nin mstaulslta btioe n. (out)54 21(ouC(ti)no)mmon Emxatedren adlu crionngn fiecetlido nin mstaulslta btioe n. (C(oinou)mt)mon (11o01ut) 87 45(ou2t1) ((oinu)t) pl p u S B74 www.nkkswitches.com

Series M Bracket PC Mount Miniature Rockers s e MOUNTING FRAMES gl g o T Narrow Mounting Frame for Small Actuators TX with Straight PC Terminals (codes 13, 15, 17, 23, 25, & 26) s or with Angle PC Terminals (codes 30 & 41) B ker c o Straight PC Mounting Right Angle PC Mounting Vertical PC Mounting R s n o 25° ( 5.2.0080) 25° 25° hbutt s (2.54) Dia (2.54) Dia (2.54) Dia Pu .100 (1.4) Typ .100 .100 .055 B (.83.105) (.313.58) ( 4.1.7327) (.00.146) Typ (2.75) (1.27) ed P (5.08) .108 (6.0) .050 at .200 .235 min u Ill e Small Actuators & Panel Cutouts for TX Frame (actuator details on the following pages) bl a m m a AT4148 AT4149 AT4150 AT4151 gr o D D Pr ire ire ctio ctio ks (1.770.81) n of Actu (.1520.70) n of Actu Keyloc a a tion (12.4) tion (10.1) .490 s .398 e ari ot R Wide Mounting Frame Large Actuators & Panel Cutouts for TZ Frame TZ for Large Actuators (actuator details on the following pages) with Straight PC Terminals s e (codes 13, 15, 17, 23, 25, & 26) Slid AT4156 AT4157 25° (12.182.25) Direction of A Tactiles (2.54) Dia ctu .100 atio (3.5) n .138 Tilt (16.0) .630 CONTACT MATERIALS & RATINGS h c u o T W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC s or at G dic Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum n I Note: See Supplement section to find complete explanation of operating range. s e ori s s A Power Level 6A @ 125V AC ce Gold over Silver or Logic Level or 0.4VA maximum @ 28V AC/DC maximum Ac Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the ent m same application. See Supplement section to find complete explanation of dual rating and operating range. e pl p u S www.nkkswitches.com B75

Series M Bracket PC Mount Miniature Rockers s e gl TERMINALS g o T For TX and TZ 1-2 Pole For TX and TZ 1-2 Pole Straight PC Mount with Bracket Straight PC Mount with Reinforced Bracket s ker B c Ro 13 15 17 23 25 26 ns .250” (6.35mm) .425” (10.8mm) .964” (24.5mm) .250” (6.35mm) .425” (10.8mm) .750” (19.05mm) o utt Terminal with Terminal with Terminal with Terminal with Terminal with Terminal with hb .465” (11.8mm) .630” (16.0mm) 1.150” (29.2mm) .465” (11.8mm) .630” (16.0mm) .953” (24.2mm) s Pu Bracket Bracket Bracket Bracket Bracket Bracket B P d e at n mi u Ill e bl a m m a gr o Pr s ck PCB footprints are on the following Typical Switch Dimension pages. o yl e K For TX 1-3 Pole Right Angle PC Mount For TX 1-4 Pole Vertical PC Mount .150” (3.81mm) .150” (3.81mm) s 30 41 arie Right Angle PC Vertical PC ot R s e d Sli ROCKERS & PADDLES FOR TX MOUNTING FRAMES AT4148 .365” (9.27mm) AT4149 .365” (9.27mm) D E es Wide Rocker Wide Paddle ctil (.93.6257) (.20.8134) Ta Material: Polyamide Material: Polyamide (9.27) (16.87) Finish: Matte .365 .664 Finish: Matte (3.96) (13.49) .156 .531 (18.8) .740 (8.43) R Tilt (7.9) (6.15) .(384.86) .332 .311 .242 (3.5) (3.5) .138 (16.8) .138 .661 h c u o T AT4150 .450” (11.43mm) AT4151 .450” (11.43mm) F G Wide Rocker Wide Paddle (11.43) (2.36) dicators MFinaitsehr:i a Ml: aPtotelyamide (1.41.5403) (9.(.114916.)85) MFinaitsehr:i a Ml: aPtotelyamide .450 .093(3.1.2185) In .362 (1.66.4346) (5.84) R ories .(381.19) .(264.38) .(370.73) .230 s cces (.313.58) (11.8) (.313.58) A .465 nt e Cap Colors m A B C E F G H ple Available: Black White Red Yellow Green Blue Gray p u S B76 www.nkkswitches.com

Series M Bracket PC Mount Miniature Rockers s e ROCKERS & PADDLES FOR TZ MOUNTING FRAMES gl g o T AT4156 .595” (15.11mm) AT4157 .595” (15.11mm) J H Wide Rocker Wide Paddle s B ker Material: Polyamide Material: Polyamide c o Finish: Matte Finish: Matte R (14.33) (2.36) .564 .093 ns o utt b h (15.11) (4.1.8775) Pus .595 (26.78) (29.82) B 1.054 (2.930.061) 1.174 (13.5) R ed P .531 at (.83.341) .(265.56) (.1413.03) .(278.37) Illumin e (3.5) (3.5) abl .138 (15.11) (26.8) .138 m .595 1.055 m a gr o Pr Cap Colors A B C E F G H Available: Black White Red Yellow Green Blue Gray ks c o yl e OPTIONAL SNAP-IN PANEL FRAMES K Used with AT4148 Rocker and AT4149 Paddle s e ari AATc0co6m4-m1odates .047” ~ .090” AATc0co6m4-m2odates .062” ~ .125” (17.9) .(399.90) .(029.30) Rot .705 (1.2 ~ 2.3mm) panel thickness (1.57 ~ 3.18mm) panel thickness s e Material: Polyamide d Finish: Matte (15.62) (25.04) Sli .615 .986 Color: Black (6.68) .263 Mounted separately from switches A ctiles a Cutout Tolerances: T Dimension A: .797” ~ .803” (20.24 ~ 20.4mm) B Dimension B: .495” ~ .505” (12.57 ~ 12.83mm) Tilt AT064–1 Enlarged Detail Used with AT4150 Rocker and AT4151 Paddle h c AT065-1 AT065-2 u (12.0) (2.3) o Accommodates .047” ~ .090” Accommodates .062” ~ .125” (12.8) .472 .090 T .504 (1.2 ~ 2.3mm) panel thickness (1.57 ~ 3.18mm) panel thickness s Material: Polyamide (1 5.6.6152) (19.43) ator Finish: Matte .765 dic Color: Black (6.68) In .263 s Mounted separately from switches e A ori s s Cutout Tolerances: ce c Dimension A: A B .595” ~ .605” (15.11 ~ 15.37mm) nt Dimension B: e m .495” ~ .500” (12.57 ~ 12.7mm) AT065–1 Enlarged Detail AT065–2 Enlarged Detail ple p u S www.nkkswitches.com B77

Series M Bracket PC Mount Miniature Rockers s e gl TYPICAL SWITCH DIMENSIONS g o T Straight PC • Bracket 25° s ker B Single Double Roc (.62.4125) .(384.86) Pole Pole s Circuit Mark n (3.5) This Side butto .138 B LREANCGKTEHT h s u TERMINAL P LENGTH (4.8) Typ 1 2 3 .189 B ed P (.00.250) Typ (.10.4176) Typ (.418.89) at (0.8) Typ (1.17) Typ (3.2) Typ min .(40.371) Typ .046 (8.0) (12.7) .126 u .185 .315 .500 Ill (15.8) .622 e abl M2012TXG13-DC m m a gr o Pr Terminal Terminal Bracket (1.6) Typ .063 Code: Length: Length: (1.6) Typ (2.4) Typ ks .063 .095 c Keylo 13 .250” (6.35mm) .465” (11.8mm) (.73.191) Typ 23 (.73.191) Typ 23 56 (4.7) Typ (4.7) Typ .185 1 .185 1 4 15 .425” (10.8mm) .630” (16.0mm) (1.8) Dia Typ (1.8) Dia Typ es .073 .073 otari 17 .964” (24.5mm) 1.150” (29.2mm) .(015.59) Dia Typ . 0(15.59) Dia Typ CL R es Straight PC • Reinforced Bracket d Sli 25° (8.8) Single Double ctiles (.62.4125) .346 Pole Pole a T Circuit Mark (3.5) This Side .138 BRACKET LENGTH Tilt T LEERNMGITNHAL 1 2 3 (.418.89) Typ (0.5) Typ (1.17) Typ (6.35) Typ .020 .046 .250 (0.8) Typ (1.17) Typ (4.8) .031 .046 .189 h (4.7) Typ (9.1) (12.7) uc .185 (19.05) .358 .500 To .750 M2012TXG23-DC s or at (2.4) Typ Indic TeCromdine:al TLeernmgitnha:l BLerangckthe:t ( 3.1.2185) Typ ( 3.1.2185). 0Ty9p5 (9.53) Typ 3 (9.53) Typ 3 6 ories 23 .250” (6.35mm) .465” (11.8mm) .375 2 .375 2 5 ess (.418.75) Typ 1 (.418.75) Typ 1 4 c 25 .425” (10.8mm) .630” (16.0mm) c A (1.8) Dia Typ (1.8) Dia Typ .073 .073 ent 26 .750” (19.05mm) .953” (24.2mm) .(015.59) Dia Typ .(015.59) Dia Typ CL m e pl p u S B78 www.nkkswitches.com

Series M Bracket PC Mount Miniature Rockers s e TYPICAL SWITCH DIMENSIONS gl g o T Single Pole .150” (3.81mm) Right Angle PC s B ker c o R Shown in Down Position Pivot (4.7) Typ 1 2 3 .185 ns (5.41) (.93.6257) (.73.191) 3 2 1 utto .213 (.416.39) (.1520.07) ushb (0.4) P ( 2.1.1825 .)(015.45(5) T.0yp8) (8 (.6..208.411)526) .(25(.1.41575.)0(71)2.7) (.10.2570) (13.0) (.(.00418.3.8751)) TTyypp (.210.50.(410.)78 T3)y Dpia Typ nated PB .200 .346 .500 .512 mi u Ill e bl a m m a M2012TXG30-DC gr o Pr Double Pole .150” (3.81mm) Right Angle PC s k c o yl e K Shown in Down Position Pivot es (.418.75) Typ ari 4 5 6 6 5 4 ot (9.27) (12.7) (3.81) R (6.4) .365 1 2 3 .500 3 2 1 .150 .252 (4.3) (12.7) .169 .500 s e (2.1.81 .2(0515.)45) Typ (.62.4152) (.(.41005..10476)) Typ (.10.5207) Typ (.(.00418.3.8751)) TTyypp (1.8) D( i2.a1.0 5T04yp) Typ Slid (5.08) (8.8) (12.7) (3.81) (13.0) .073 .200 .346 .500 .150 .512 s e ctil a T M2022TXG30-DC Three Pole .150” (3.81mm) Right Angle PC Tilt Shown in h Down Position Pivot uc (4.7) Typ To .185 7 8 9 9 8 7 (3.81) Typ (9.27) (17.5) 6 5 4 .150 .(384.86) .365 14 25 63 .689 3 2 1 ators c (4.3) (14.35) di .169 .565 In (2.85) (0.4) (0.8) Typ .112 .016 .031 s .(015.45) Typ (.62.4152) (.417.57) (.10.5207) Typ (.418.75) Typ ( 2.1.0504) Typ orie (5.2.0080) .(384.86) (1.45.6355) ( 3.1.5801) Typ (1.531.02) .(017.83) Dia Typ cess c A nt e m M2032TXG30-DC e pl p u S www.nkkswitches.com B79

Series M Bracket PC Mount Miniature Rockers s e gl TYPICAL SWITCH DIMENSIONS g o T .150” (3.81mm) Vertical PC Single Pole s cker B (.93.6257) .(384.86) (.313.58) o R 3 (3.81) Typ ns 25° ( 1.531.02) 2 .150 butto .(396.10) ( 3.1.2185) 1 h (12.7) us .500 P (0.4) Typ (2.74) (1.27) (0.8) Typ (1.27) B .016 .108 .050 .031 .050 nated P (.52.0008) SDhoowwnn P ionsition (.62.4152) ( 5.2.9375) (.1520.07) ( 3.1.5801) Typ (.73.191) . 0(17.83) D( 2.i1a.05 T04y)p Typ mi M2012TXG41-DC u Ill e bl .150” (3.81mm) Vertical PC Double Pole a m m ogra (.93.6257) .(384.86) (.313.58) Pr (2.4) Typ .094 6 3 3 6 ocks 25° 5 2 ( 1.531.02) 2 5 (.315.801) Typ Keyl .(396.10) ( 3.1.2185) 4 1 1 4 (12.7) .500 (1.27) Typ .050 s (0.4) Typ (2.74) (1.27) (0.8) Typ (4.8) arie .016(5.08) Show .1n0 8in (6.15) (5.97) .0 (5120.7) (.30.3811) Typ (.1128.97) (.210.504) Typ ot .200 Down Position .242 .235 .500 .150 .500 (1.8) Dia Typ R .073 M2022TXG41-DC es .150” (3.81mm) Vertical PC Three Pole d Sli (9.27) (8.8) (3.5) .365 .346 .138 (4.8) Typ es 9 6 3 3 6 9 .189 actil 25° 8 5 2 ( 1.531.02) 2 5 8 ( 3.1.5801) Typ T (9.1) 7 4 1 1 4 7 .360 (3.18) .125 (14.35) (1.27) Typ .565 Tilt .(00.146) Typ ( 2.1.0784) (.10.5207) (.00.381) Typ (.418.89) Typ .050 (5.08) Shown in (6.15) (5.97) (14.35) (3.81) Typ (17.5) (2.54) Typ . 2 00 Down Position .242 .235 .565 .150 .689 .100 (1.8) Dia Typ .073 M2032TXG41-DC h c u o .150” (3.81mm) Vertical PC Four Pole T (9.27) (8.8) (3.5) ors .365 .346 .138 at (4.8) Typ dic 12 9 6 3 3 6 9 12.189 n (3.81) Typ I 25° 11 8 5 2 (.1531.20) 2 5 8 11 .150 es .(396.10) (3.18) 10 7 4 1 1 4 7 10 sori .125 (14.35) es .565 c c (0.4) Typ (2.74) (1.27) (0.8) Typ (4.8) Typ (1.27) Typ A .016 .108 .050 .031 .189 .050 (5.08) Shown in (6.15) (5.97) (14.35) (3.81) Typ (22.3) (2.54) Typ nt .200 Down Position .242 .235 .565 .150 .878 .100 e (1.8) Dia Typ m .073 e pl M2042TXG41-DC p u S B80 www.nkkswitches.com

Series M Bracket PC Mount Miniature Rockers s e TYPICAL SWITCH DIMENSIONS gl g o T Straight PC • Bracket 25° s (11.0) Single Double B cker .(266.60) .433 Pole Pole Ro (.313.58) CThiricsu Sitid Meark ons BLERNAGCTKHET butt h TERMINAL us LENGTH (4.8) Typ P 1 2 3 .189 (.(.0000..236841)) TTyypp .((101..411776)) TTyypp ((.3418..289)) Typ ated PB (.418.75) Typ (15.8) .046 (.83.105) (.1520.07) .126 umin .622 Ill e bl M2012TZG13-JC a m m a gr o (1.6) Typ Terminal Terminal Bracket Pr .063 .(016.63) Typ .(029.45) Typ Code: Length: Length: ks c (7.9) Typ 3 (7.9) Typ 3 6 ylo .311 2 .311 2 5 13 .250” (6.35mm) .465” (11.8mm) Ke (4.7) Typ (4.7) Typ .185 1 .185 1 4 15 .425” (10.8mm) .630” (16.0mm) (1.8) Dia Typ (1.8) Dia Typ s .073 .073 e .(015.59) Dia Typ . 0(15.59) Dia Typ CL 17 .964” (24.5mm) 1.150” (29.2mm) otari R Straight PC • Reinforced Bracket es d Sli 25° Single Double (11.0) s .(266.60) .433 Pole Pole ctile a T Circuit Mark (3.5) This Side .138 BRACKET LENGTH TLEENRMGTINHAL (4.8) Typ Tilt 1 2 3 .189 (.00.250) Typ (.10.4176) Typ ( 6.2.3550) Typ (0.8) Typ .031 (1.17) Typ (4.8) (.418.75) Typ (19.05) .046 .(395.18) (.1520.07) .189 ouch .750 T M2012TZG23-JC s or (2.4) Typ at (3.18) Typ .095 Terminal Terminal Bracket dic .125 ( 3.1.2185) Typ Code: Length: Length: In (9.53) Typ 3 (9.53) Typ 3 6 s .375 2 .375 2 5 23 .250” (6.35mm) .465” (11.8mm) orie (4.7) Typ (4.7) Typ ss .185 1 .185 1 4 25 .425” (10.8mm) .630” (16.0mm) cce (1.8) Dia Typ (1.8) Dia Typ A .073 .073 .(015.59) Dia Typ .(015.59) Dia Typ CL 26 .750” (19.05mm) .953” (24.2mm) ent m e pl p u S www.nkkswitches.com B81

Series M Bracket PC Mount Miniature Rockers s e gl LEGENDS g o T NKK Switches can provide custom legends for caps. Contact factory for more information. s ker B c o R Suggested Printable Area for Cap s n o utt AT4148 AT4150 AT4156 b h s u P B P d O O minate OFFN OFFON OFFN u Ill e bl a m m a gr o Pr (0.38) Typ .015 (0.38) Typ (0.38) Typ .015 .015 s ylock (.62.792) Typ ( 5.2.7267) Typ (.417.57) Typ (11.18) Typ (10.03) Typ e .440 .395 K (0.76) Typ (7.75) (0.76) Typ (0.76) Typ (9.91) (0.76) Typ (3.36) Typ .030 .305 .030 .030 .390 .030 .132 (11.43) (0.76) Typ (13.59) (0.76) Typ (9.27) .450 .030 .535 .030 s .365 arie (1.559.151) ot R Shaded areas are printable areas. es Recommended Print Method: d Sli Pad Print Epoxy based ink is recommended. s e ctil a T Tilt h c u o T s or at c di n I s e ori s s e c c A nt e m e pl p u S B82 www.nkkswitches.com

Series M Flat Frame Mount Miniature Rockers s e TYPICAL SWITCH ORDERING EXAMPLE gl g o T M20 1 2 TN W 01 D C s B ker c o R s Poles Rockers & Paddles on utt 1 SPDT Mounting Frames Small Actuators (TN Frame) hb s u DPDT .272” (6.9mm) Wide .365” (9.27mm) P 2 TN D SP3T Flat Frame Wide Rocker B P d 3 3PDT TY .504” (12.8mm) Wide E .365” (9.27mm) ate 4PDT Flat Frame Wide Paddle min 4 u DP3T F .450” (11.43mm) Ill Wide Rocker ble a m Cont&a cRt aMtiantgesr ials G .W45id0e” P(1a1d.d4le3mm) gram Circuits o Large Actuators (TY Frame) Pr Silver; Rated 6A @ 125V 2 ON NONE ON W AC & 3A @ 250V AC .595” (15.11mm) s J k 3 ON OFF ON Wide Rocker oc 5 ON NONE (ON) G G28oVld ;A RCa/teDd C 0 m.4aVxA max @ .595” (15.11mm) Keyl H Wide Paddle 8 (ON) OFF (ON) Gold over Silver; Rated 9 ON OFF (ON) A 6A @ 125V AC & 0.4VA es max @ 28V AC/DC max ari *4 ON ON ON ot R Rocker & Paddle *6 (ON) ON (ON) Terminals Colors *7 ON ON (ON) 01 Solder Lug A Black es ( ) = Momentary .250” (6.35mm) B White Slid *3-ON circuits 03 Straight PC C Red E Yellow s e F Green actil T IMPORTANT: G Blue Switches are supplied without UL & CSA marking unless specified. H Gray UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings and ordering instructions are noted on the Tilt General Specifications page. h c u o DESCRIPTION FOR TYPICAL ORDERING EXAMPLE T M2012TNW01-DC s or at c di Red .365” (9.27mm) In Wide Rocker s e .272” (6.9mm) Wide ori SPDT Flat Frame ess c ON-NONE-ON Circuit c A Silver Contacts Solder Lug Terminals with 6-Amp Rating nt e m e pl p u S www.nkkswitches.com B83

Series M Flat Frame Mount Miniature Rockers s e gl POLES & CIRCUITS g o T Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics s ker B Down Center Up Down Center Up c Note: Terminal numbers are not actually o R Pole Model on the switch. s n o utt M2012 ON NONE ON SPDT b sh M2013 ON OFF ON Pu SP M2015 ON NONE (ON) 2-3 OPEN 2-1 2 (COM) ed PB MM22001189 (OONN) OOFFFF ((OONN)) 3 1 at n mi u M2022 ON NONE ON DPDT Ill M2023 ON OFF ON ble DP M2025 ON NONE (ON) 2-3 5-6 OPEN 2-1 5-4 2 (COM) 5 a m M2028 (ON) OFF (ON) m 3 1 6 4 a gr M2029 ON OFF (ON) o Pr M2032 ON NONE ON 3PDT ks M2033 ON OFF ON oc 3P M2035 ON NONE (ON) 2-3 5-6 OPEN 2-1 5-4 2 5 (COM) 8 yl 8-9 8-7 Ke M2038 (ON) OFF (ON) 3 1 6 4 9 7 M2039 ON OFF (ON) s e M2042 ON NONE ON 4PDT Rotari 4P MM22004435 OONN NOOFNFE (OONN) 2-3 5-6 OPEN 2-1 5-4 2 5 (COM) 8 11 8-9 11-12 8-7 11-10 M2048 (ON) OFF (ON) 3 1 6 4 9 7 12 10 M2049 ON OFF (ON) s e d Sli For 3 Throw (3-On) Connected Terminals & Schematics s e ctil Pole Model Down Center Up Down Center Up a T External External External Connection Connection Connection M2024 ON ON ON 2 (in) 5 2 (in) 5 2 (in) 5 Tilt SP MM22002267 (OONN) OONN ((OONN)) 1 (out) 34 (out) 6 (out) 1 (out) 34 (out) 6 (out) 1 (out) 34 (out)6 (out) 2-3 5-6 2-3 5-4 2-1 5-4 h External External External External External External uc Connection Connection Connection Connection Connection Connection To 2 (in) 5 8 (in) 11 2 (in) 5 8 (in) 11 2 (in) 5 8 (in) 11 M2044 ON ON ON DP M2046 (ON) ON (ON) 1 (out) 34 (out)6 (out)7 (out)910 (out)12 (out) 1 (out) 34 (out)6 (out)7 (out)910 (out) 12 (out) 1 (out) 34 (out)6 (out)7 (out)910 (out)12 (out) s M2047 ON ON (ON) or at 2-3 5-6 2-3 5-4 2-1 5-4 c di 8-9 11-12 8-9 11-10 8-7 11-10 n I The SP3T model utilizes a The DP3T model utilizes a s e ori double pole base. (out) four pole base. (out) (out) s cces ECxotnenrnal 6 3 ECxotnenrnal 12 9 6 3 Common A 5 2 C(ino)mmon C(ino)mmon 11 8 5 2 ((oinu)t) ment External connection must be (out)4 1(out) External connection must be (out) (1o0ut) 7 4(out1) e made during field installation. made during field installation. pl p u S B84 www.nkkswitches.com

Series M Flat Frame Mount Miniature Rockers s e MOUNTING FRAMES gl g o T .272” (6.9mm) TN Wide Flat Frame (3.5) (6.9) .138 .272 B kers c o R s (29.5) (23.8) on 1.161 .937 utt b h Mounting hardware kit HK-1, as shown on the us P following page, must be ordered separately. B P (0.6) (2.4) Dia Typ ed .024 .094 at n mi u Ill Small Actuators & Panel Cutouts for TN Frame (actuator details on the following pages) ble a m m a AT4148 AT4149 AT4150 AT4151 gr o Pr s k (1.770.81) (.1520.70) yloc (23.8) (23.8) e .937 .937 K s (.1309.81) (.210.62) Dia Typ (.1429.40) (.210.62) Dia Typ otarie R TY .504” (12.8mm) Large Actuators & Panel Cutout for TY Frame es Wide Flat Frame (actuator details on the following pages) Slid AT4156 AT4157 s e ctil a T Mounting hardware kit HK-2, as shown on the following page, must be ordered separately. Tilt h (3.5) (12.8) uc .138 .504 o T s or at c di (28.5) n (41.3) (34.9) 1.122 I 1.6261.374 (34.9) 1.374 s e ori s s e c c A (3.5) Dia Typ .138 nt (.00.264) (.312.26) Dia Typ (.1663.00) eme pl p u S www.nkkswitches.com B85

Series M Flat Frame Mount Miniature Rockers s e gl MOUNTING FRAMES (CONTINUED) g o T Face Panel Mounting Subpanel Mounting s Flat frame devices may These devices are especially ker B also be mounted to the designed for subpanel mounting. c Ro face panel. Standoffs When installed on a mounting are used to recess the plate behind the panel, hardware s actuator and achieve is completely concealed and n o an attractive front panel the front panel retains a clean, butt STLAENNGDTOHFF appearance. attractive appearance. h s u P B d P Optional Hardware Kits Optional Snap-in Panel Frames e at n for Subpanel or Face Panel Mounting mi Further Illu Panel Standoff Hardware details are e Frame Thickness Length Kit Number shown in bl a the previous m TN Frame .125” (3.175mm) .233” (5.918mm) ATHK-1 m bracketed a gr TY Frame .125” (3.175mm) .312” (7.925mm) ATHK-2 PC mount o Pr subsection. Hardware kits include: s 2 stainless steel screws, 2 hex nuts, 2 lockwashers, & 2 standoffs AT064-1 AT065-1 k oc AT064-2 AT065-2 yl e K CONTACT MATERIALS & RATINGS s e otari W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC R G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum s e Slid Note: See Supplement section to find complete explanation of operating range. A s Gold over Silver Power Level 6A @ 125V AC e ctil or Logic Level or 0.4VA maximum @ 28V AC/DC maximum a T Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. Tilt TERMINALS 01 Solder Lug (4.0) Epoxy Seal .157 h c u o (2.0) (2.0) T .079 (1.1) .079 .043 Thk = (0.8) .031 s or at c di .250” (6.35mm) n 03 I Straight PC (.418.89) (.418.89) Typ (.418.89) Typ s 3 3 6 3 6 9 3 6 9 12 orie 2(.418.75) Typ 2 5 (.418.75) Typ 2 5 8 (.418.75) Typ 2 5 8 11 (.418.75) Typ cess Epoxy Seal (.418.89) (.62.5305) 1 1 4 1 4 7 1 4 7 10 Ac (.10.783) Dia Typ (1.8) Dia Typ (1.8) Dia Typ (1.8) Dia Typ (1.17) .073 .073 .073 nt .046 e Thk = (0.8) m .031 Single Pole Double Pole Three Pole Four Pole e pl p u S B86 www.nkkswitches.com

Series M Flat Frame Mount Miniature Rockers s e ROCKERS & PADDLES gl g o T For TN Frame s D AT4148 .365” (9.27mm) E AT4149 .365” (9.27mm) B ker Wide Rocker Wide Paddle oc R Material: Polyamide Material: Polyamide Finish: Matte Finish: Matte ns o utt b (9.27) (2.13) sh .365 .084 u P (9.27) (16.87) B .365 .664 (3.96) P (13.49) .156 d .531 (.1784.80) (8.43) R nate (8.8) .332 mi (7.9) (6.15) .346 u .311 .242 Ill e (3.5) (3.5) abl .138 (1.666.81) .138 amm gr o Pr AT4150 .450” (11.43mm) AT4151 .450” (11.43mm) F G s Wide Rocker Wide Paddle ck o yl Material: Polyamide Material: Polyamide Ke Finish: Matte Finish: Matte (11.43) (2.36) s (11.43) (11.8) .450 .093 arie .450 .465 (3.18) ot (9.19) .125 R .362 (16.36) .644 (5.84) R .(381.19) .(264.38) .(370.73) .230 es d (3.5) Sli .138 (3.5) (11.8) .138 .465 s For TY Frame e ctil a AT4156 .595” (15.11mm) AT4157 .595” (15.11mm) T J H Wide Rocker Wide Paddle Material: Polyamide Material: Polyamide Finish: Matte Finish: Matte Tilt (14.33) (2.36) .564 .093 h c u o T (4.75) (15.11) .187 .595 s (26.78) (29.82) or 1.054 (23.01) 1.174 at .906 (13.5) R c .531 di (.83.341) .(265.56) (.1413.03) .(278.37) Ins e (.313.58) (15.11) (26.8) (.313.58) essori .595 1.055 c c A nt Cap Colors e A B C E F G H m Available: Black White Red Yellow Green Blue Gray ple p u S www.nkkswitches.com B87

Series M Flat Frame Mount Miniature Rockers s e gl TYPICAL SWITCH DIMENSIONS g o T TN Frame • Solder Lug Single Pole (2.4) Dia Typ (12.3) s .094 .484 (3.5) (1.1) x (2.0) Typ ker B .138 .043 x. 079 c Circuit Mark Ro This Side 3 (23.8) (4.7) Typ ns .937 25° .185 2 (13.0) o (29.5) .512 utt 1.161 (0.8) Typ 1 b .031 h s u P B P d (6.9) (7.9) (0.6) (0.5) (2.0) minate M2012TNW01-DC (..923.762257) .(39.31.68150) ..(014020.463) (.417.57) .020 (.73.191) .079 u Ill e TN Frame • Solder Lug Double Pole bl ma (2.4) Dia Typ (12.3) m .094 .484 (3.5) (1.1) x (2.0) Typ (2.0) Typ gra .138 .043 x. 079 .079 o Circuit Mark Pr This Side cks (23.8) (4.7) Typ 6 3 ylo (29.5).937 25° .185 5 2 (1.531.02) Ke 1.161 (0.8) Typ .031 4 1 s e Rotari .(267.92) (.73.191) .(002.64) .(002.50) (.418.89) (9.27) (9.65) (10.3) (4.5) (12.7) M2022TNW01-DC .365 .380 .406 .177 .500 s TN Frame • Solder Lug Three Pole e d Sli (.20.944) Dia Typ (.1428.34) (3.5) (1.1) x (2.0) Typ (2.0) Typ .138 .043 x .079 .079 Circuit Mark This Side s e actil (23.8) (4.7) Typ 9 6 3 T (29.5) .937 25° .185 8 5 2 (1.531.02) 1.161 (0.8) Typ 7 4 1 .031 Tilt (6.9) (7.9) (0.6) (0.5) (4.8) Typ .272 .311 .024 .020 .189 (9.27) (9.65) (12.4) (4.5) (17.5) M2032TNW01-DC .365 .380 .488 .177 .689 h c u To TN Frame • Solder Lug Four Pole (2.4) Dia Typ (12.3) .094 .484 (3.5) (1.1) x (2.0) Typ (2.0) Typ s .138 .043 x .079 .079 or at Circuit Mark dic This Side n I 12 9 6 3 (23.8) (4.7) Typ es (29.5) .937 25° .185 11 8 5 2 (1.531.02) sori 1.161 (.00.381) Typ 10 7 4 1 s e c c A nt (6.9) (7.9) (0.6) (0.5) (4.8) Typ me .272 .311 .024 .020 .189 e (9.27) (9.65) (12.4) (4.5) (22.3) ppl M2042TNW01-DC .365 .380 .488 .177 .878 u S B88 www.nkkswitches.com

Series M Flat Frame Mount Miniature Rockers s e TYPICAL SWITCH DIMENSIONS gl g o T TY Frame • Solder Lug Single Pole Double Pole (3.2) Dia Typ (14.5) s .126 .571 (.313.58) . 0(14.13) xx (.20.709) Typ B cker o R Circuit Mark This Side s n o (34.9) (4.7) Typ 3 6 3 hbutt (41.3)1.374 25° .185 2 (.1531.20) 5 2 (.1531.20) Pus 1.626 (0.8) Typ .031 1 4 1 B P d e at n mi u Ill (12.8) (8.4) (0.6) (0.5) (2.0) (2.0) Typ ble .504 .331 .024 .020 .079 .079 a (.1559.151) (.1309.04) (.1309.04) (.417.57) (.73.191) (.418.89) amm gr Double pole has barrier between terminals. M2012TYW01-JC o Pr Three Pole TY Frame • Solder Lug s k c o (.312.26) Dia Typ (14.5) (.20.709) Typ eyl .571 (3.5) (1.1) x (2.0) Typ K .138 .043 x .079 Circuit Mark es This Side ari ot 9 6 3 R (34.9) (4.7) Typ (41.3)1.374 25° .185 8 5 2 (.1531.20) 1.626 (.00.381) Typ 7 4 1 es d Sli s (.1520.84) (.83.341) .(002.64) .(002.50) .(418.89) Typ actile (.1559.151) (.1309.04) (.1427.61) (.417.57) .(1678.59) T M2032TYW01-JC Four Pole TY Frame • Solder Lug Tilt (3.2) Dia Typ (2.0) Typ .126 (14.5) .079 .571 (3.5) (1.1) x (2.0) Typ .138 .043 x .079 ch u o T Circuit Mark This Side 12 9 6 3 s (34.9) (4.7) Typ or 1.374 .185 11 8 5 2 (13.0) at 1(4.612.36) 25° (0.8) Typ 10 7 4 1 .512 ndic .031 I s e ori s s e c c (12.8) (8.4) (0.6) (0.5) (4.8) Typ A .504 .331 .024 .020 .189 (.1559.151) (.1309.04) (.1427.61) (.417.57) ( 2.827.83) ent m e M2042TYW01-JC pl p u S www.nkkswitches.com B89

Series M Flat Frame Mount Miniature Rockers s e gl LEGENDS g o T NKK Switches can provide custom legends for caps. Contact factory for more information. s ker B c Ro Suggested Printable Area for Caps s n o utt AT4148 AT4150 AT4156 b h s u P B P minated OFFON OFFON OFON u F Ill e bl a m m a gr o Pr (0.38) Typ s .015 (0.38) Typ (0.38) Typ ck .015 .015 o yl (6.9) Typ (5.76) Typ (4.5) Typ Ke .272 .227 .177 (11.18) Typ (10.03) Typ .440 .395 (0.76) Typ (7.75) (0.76) Typ (0.76) Typ (9.91) (0.76) Typ (3.36) Typ .030 .305 .030 .030 .390 .030 .132 Rotaries (.93.6257) (1.41.5403) (.00.3706) Typ ((11..3555.39.515591)) (.00.3706) Typ Shaded areas are printable areas. s e d Sli Recommended Print Method: Pad Print s ctile Epoxy based ink is recommended. a T Tilt h c u o T s or at c di n I s e ori s s e c c A nt e m e pl p u S B90 www.nkkswitches.com

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N KK Switches: M2044TNW01-DH M2018TNW01-DA M2018TYW01-JA M2018TNW01-EA M2015TNW01-EA M2018TJW03-GA- 1A M2012TJG01-FH-1A M2012TXG41-DC M2012TYW01-JA M2012TJW02-FG-3A-FC M2012TNW01-EA M2012TNW01-DA M2019TJG01-FA-2A-F M2019TNW01-DA M2019TNW01-EA M2013TNW01-EA M2013TNW01- DA M2019TYW01-HH M2033TNW01-EA M2032TNW01-DA M2032TYW01-JA M2033TNW01-DA M2042TNW01- EA M2042TNW01-DA M2042TYW01-JA M2028TYW01-JA M2028TNW01-EA M2022TNW01-EA M2022TNW01-DA M2023TJW01-FA-3A-CF M2022TYW01-JA M2029TNW01-EA M2029TNW01-DA M2022TJG01-FB-1B M2022TJG01-GB-1B M2029TJG02-FC-3A-CE M2023TNW01-DA M2029TJW01-FC-3A-CE M2028TJW01-GA-1A M2023TNW01-EA M2028TJW01-GA M2028TNW01-DA M2012TJA02-FH-3A-FC M2012TJA02-GH-3A-FC M2012TJG01-FA-1A M2012TJG01-FA-2A-C M2012TJG01-FA-3A-CF M2012TJG01-FC-1A M2012TJG01-FC-2A-C M2012TJG01-FE-1A M2012TJG01-GA-1A M2012TJG01-SA-1A M2012TJW01-FA M2012TJW01-FA-1A M2012TJW01-FA-1H M2012TJW01-FA-2A-F M2012TJW01-FA-3A-EF M2012TJW01-FA-4A-CF M2012TJW01-FB-1A M2012TJW01-FC-1A M2012TJW01-FC-1C M2012TJW01-FC-1G M2012TJW01-FC-2A-C M2012TJW01-FC-3A-CF M2012TJW01-FE-1A M2012TJW01-FF M2012TJW01-FF-1A M2012TJW01-FF-1G M2012TJW01-FG-1A M2012TJW01-FH-3A-CF M2012TJW01-GA-1A M2012TJW01-GA-2A M2012TJW01-GB-1A M2012TJW01-GC-1A M2012TJW01-GH-4A-EE M2012TJW01-SA M2012TJW02-FA-1A M2012TJW02-FA-4A-EE M2012TJW02-FC-1A M2012TJW02-GA-1A M2012TJW03-FA-1A M2012TJW03-FA-2A M2012TJW03-FA-4A-FE M2012TNG01 M2012TNG01-DA M2012TNG01-DB M2012TNG01-DC M2012TNW01 M2012TNW01-DC M2012TNW03-DA M2012TXW15-DH M2012TYG01-HH M2012TYW01 M2012TYW01-JB M2012TYW01-JC M2012TYW01-JH M2013TJG01-FA-1A M2013TJG01-FA-3A-CC M2013TJG01-FC-1A M2013TJG01-FC-3A-CF