Typical Size 6,4 mm X 9,7 mm TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 4-V TO 6-V INPUT, 8-A OUTPUT TRACKING SYNCHRONOUS BUCK ™ PWM SWITCHER WITH INTEGRATED FETs (SWIFT ) FOR SEQUENCING FEATURES DESCRIPTION (cid:1) Power Up/Down Tracking For Sequencing As a member of the SWIFT™ family of dc/dc regulators, (cid:1) 30-mΩ, 12-A Peak MOSFET Switches for High the TPS54880 low-input voltage high-output current Efficiency at 8-A Continuous Output Source synchronous buck PWM converter integrates all or Sink Current required active components. Using the TRACKIN pin (cid:1) Wide PWM Frequency: with other regulators, simultaneous power up and down Fixed 350 kHz or Adjustable 280 kHz to are easily implemented. Included on the substrate with 700 kHz the listed features are a true, high performance, voltage (cid:1) error amplifier that enables maximum performance and Power Good and Enable flexibility in choosing the output filter L and C (cid:1) Load Protected by Peak Current Limit and components; an under-voltage-lockout circuit to Thermal Shutdown prevent start-up until the input voltage reaches 3.8 V; an (cid:1) Integrated Solution Reduces Board Area and internally or externally set slow-start circuit to limit Component Count inrush currents; and a power good output useful for processor/logic reset. APPLICATIONS The TPS54880 is available in a thermally enhanced (cid:1) Low-Voltage, High-Density Distributed Power 28-pin TSSOP (PWP) PowerPAD™ package, which Systems eliminates bulky heatsinks. TI provides evaluation (cid:1) modules and the SWIFT™ designer software tool to aid Point of Load Regulation for High in quickly achieving high-performance power supply Performance DSPs, FPGAs, ASICs and designs to meet aggressive equipment development Microprocessors Requiring Sequencing (cid:1) cycles. Broadband, Networking and Optical Communications Infrastructure SIMPLIFIED SCHEMATIC I/O Supply STARTUP TIMING v di Input VIN PH Core Supply e −1 V/ VfsI == 750 V0 kHz I/O g CORE TPS54880 olta BOOT ut V TRACKIN PGND utp O VBAIAGSNDVCSOEMNPSE − VO PWRGD(I/O) 5 V/div − d o o G er PWRGD(CORE) w o p t − Time − 500 µs/div Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD and SWIFT are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products Copyright © 2002 − 2005, Texas Instruments Incorporated conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION TA OUTPUT VOLTAGE PACKAGE PART NUMBER −40°C to 85°C 0.9 V to 3.3 V Plastic HTSSOP (PWP)(1)(2) TPS54880PWP (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. (2) The PWP package is also available taped and reeled. Add an R suffix to the device type (i.e., TPS54880PWPR). See the application section of this data sheet for PowerPAD drawing and layout information. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1) TPS54880 VIN, ENA −0.3 V to 7 V RT −0.3 V to 6 V IInnppuutt vvoollttaaggee rraannggee, VVI VSENSE, TRACKIN −0.3 V to 4V BOOT −0.3 V to 17 V VBIAS, COMP, PWRGD −0.3 V to 7 V OOuuttppuutt vvoollttaaggee rraannggee, VVO PH −0.6 V to 10 V PH Internally Limited SSoouurrccee ccuurrrreenntt, IIO COMP, VBIAS 6 mA PH 12 A SSiinnkk ccuurrrreenntt,, IISS COMP 6 mA ENA, PWRGD 10 mA Voltage differential AGND to PGND ±0.3 V Operating virtual junction temperature range, TJ −40°C to 125°C Storage temperature, Tstg −65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 300°C (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS MIN NOM MAX UNIT Input voltage, VI 4 6 V Operating junction temperature, TJ −40 125 °C DISSIPATION RATINGS(1)(2) PACKAGE THERMAL IMPEDANCE TA =25°C TA = 70°C TA = 85°C JUNCTION-TO-AMBIENT POWER RATING POWER RATING POWER RATING 28 Pin PWP with solder 18.2 °C/W 5.49 W(3) 3.02 W 2.20 W 28 Pin PWP without solder 40.5 °C/W 2.48 W 1.36 W 0.99 W (1) For more information on the PWP package, refer to TI technical brief, literature number SLMA002. (2) Test board conditions: 1. 3” x 3”, 4 layers, thickness: 0.062” 2. 1.5 oz. copper traces located on the top of the PCB 3. 1.5 oz. copper ground plane on the bottom of the PCB 4. 0.5 oz. copper ground planes on the 2 internal layers 5. 12 thermal vias (see “Recommended Land Pattern” in applications section of this data sheet) (3) Maximum power dissipation may be limited by over current protection. 2

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 ELECTRICAL CHARACTERISTICS over operating free-air temperature range unless otherwise noted PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY VOLTAGE, VIN Input voltage range, VIN 4.0 6.0 V fs = 350 kHz, RT open, 11 15.8 PH pin open II(Q) QQuuiieesscceenntt ccuurrrreenntt fs = 500 kHz, RT = 100 kΩ, PH pin open 16 23.5 mmAA Shutdown, ENA = 0 V 1 1.4 UNDER VOLTAGE LOCK OUT Start threshold voltage, UVLO 3.8 3.85 V Stop threshold voltage, UVLO 3.4 3.5 V Hysteresis voltage, UVLO 0.14 0.16 V Rising and falling edge deglitch, UVLO(1) 2.5 µs BIAS VOLTAGE Output voltage, VBIAS I(VBIAS) = 0 2.70 2.80 2.90 V Output current, VBIAS (2) 100 µA CUMULATIVE REFERENCE Vref Accuracy 0.882 0.891 0.900 V REGULATION LLiinnee rreegguullaattiioonn((11))((33)) IL = 3 A, fs = 350 kHz, TJ = 85°C 0.04 %%//VV IL = 3 A, fs = 550 kHz, TJ = 85°C 0.04 LLooaadd rreegguullaattiioonn((11))((33)) IL = 0 A to 6 A, fs = 350 kHz, TJ = 85°C 0.03 %%//AA IL = 0 A to 6 A, fs = 550 kHz, TJ = 85°C 0.03 OSCILLATOR Internally set—free running frequency RT open 280 350 420 kHz RT = 180 kΩ (1% resistor to AGND) 252 280 308 EExxtteerrnnaallllyy sseett—ffrreeee rruunnnniinngg ffrreeqquueennccyy rraannggee RT = 100 kΩ (1% resistor to AGND) 460 500 540 kkHHzz RT = 68 kΩ (1% resistor to AGND) 663 700 762 Ramp valley(1) 0.75 V Ramp amplitude (peak-to-peak)(1) 1 V Minimum controllable on time(1) 200 ns Maximum duty cycle 90% (1) Specified by design (2) Static resistive loads only (3) Specified by the circuit used in Figure 9 3

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 ELECTRICAL CHARACTERISTICS (continued) over operating free-air temperature range unless otherwise noted PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ERROR AMPLIFIER Error amplifier open loop voltage gain 1 kΩ COMP to AGND(1) 90 110 dB Error amplifier unity gain bandwidth Parallel 10 kΩ, 160 pF COMP to AGND(1) 3 5 MHz Error amplifier common mode input voltage range Powered by internal LDO(1) 0 VBIAS V Input bias current, VSENSE VSENSE = Vref 60 250 nA Output voltage slew rate (symmetric), COMP 1.0 1.4 V/µs PWM COMPARATOR PWM comparator propagation delay time, PWM comparator input to PH pin (excluding 10-mV overdrive(1) 70 85 ns deadtime) ENABLE Enable threshold voltage, ENA 0.82 1.20 1.40 V Enable hysteresis voltage, ENA 0.03 V Falling edge deglitch, ENA(1) 2.5 µs Leakage current, ENA VI = 5.5 V 1 µA POWER GOOD Power good threshold voltage VSENSE falling 90 %Vref Power good hysteresis voltage(1) 3 %Vref Power good falling edge deglitch(1) 35 µs Output saturation voltage, PWRGD I(sink) = 2.5 mA 0.18 0.3 V Leakage current, PWRGD VI = 5.5 V 1 µA CURRENT LIMIT VI = 4.5 VOutput shorted(1) 9 1 CCurrentt lliimiitt ttriip poiintt AA VI = 6 V Output shorted(1) 10 12 Current limit leading edge blanking time 100 ns Current limit total response time 200 ns THERMAL SHUTDOWN Thermal shutdown trip point(1) 135 150 165 °C Thermal shutdown hysteresis(1) 10 °C OUTPUT POWER MOSFETS rrDS(on) PPoowweerr MMOOSSFFEETT sswwiittcchheess VVII == 46. 5V (V4)(4) 2360 4670 mmΩΩ TRACKIN Input offset, TRACKIN VSENSE = TRACKIN = 1.25 V −1.5 1.5 mV Input voltage range, TRACKIN See Note 1 0 Vref V (1) Specified by design (2) Static resistive loads only (3) Specified by the circuit used in Figure 9 (4) Matched MOSFETs low-side rDS(on) production tested, high-side rDS(on) specified by design 4

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 PWP PACKAGE (TOP VIEW) AGND 1 28 RT VSENSE 2 27 ENA COMP 3 26 TRACKIN PWRGD 4 25 VBIAS BOOT 5 24 VIN PH 6 23 VIN PH 7 THERMAL 22 VIN PH 8 PAD 21 VIN PH 9 20 VIN PH 10 19 PGND PH 11 18 PGND PH 12 17 PGND PH 13 16 PGND PH 14 15 PGND TERMINAL FUNCTIONS TERMINAL DDEESSCCRRIIPPTTIIOONN NAME NO. AGND 1 Analog ground. Return for compensation network/output divider, slow-start capacitor, VBIAS capacitor, RT resistor. Connect PowerPAD to AGND. BOOT 5 Bootstrap output. 0.022-µF to 0.1-µF low-ESR capacitor connected from BOOT to PH generates floating drive for the high-side FET driver. COMP 3 Error amplifier output. Connect frequency compensation network from COMP to VSENSE ENA 27 Enable input. Logic high enables oscillator, PWM control and MOSFET driver circuits. Logic low disables operation and places device in low quiescent current state. PGND 15−19 Power ground. High current return for the low-side driver and power MOSFET. Connect PGND with large copper areas to the input and output supply returns, and negative terminals of the input and output capacitors. A single point connection to AGND is recommended. PH 6−14 Phase output. Junction of the internal high-side and low-side power MOSFETs, and output inductor. PWRGD 4 Power good open drain output. High when VSENSE ≥ 90% Vref, otherwise PWRGD is low. RT 28 Frequency setting resistor input. Connect a resistor from RT to AGND to set the switching frequency. TRACKIN 26 External reference input. High impedance input to internal reference/multiplexer and error amplifier circuits. VBIAS 25 Internal bias regulator output. Supplies regulated voltage to internal circuitry. Bypass VBIAS pin to AGND pin with a high quality, low-ESR 0.1-µF to 1.0-µF ceramic capacitor. VIN 20−24 Input supply for the power MOSFET switches and internal bias regulator. Bypass VIN pins to PGND pins close to device package with a high quality, low-ESR 10-µF ceramic capacitor. VSENSE 2 Error amplifier inverting input. Connect to output voltage through compensation network/output divider. 5

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 INTERNAL BLOCK DIAGRAM AGND VBIAS Enable Comparator VBIAS REG ENA Falling SHUTDOWN 1.2 V Edge ILIM VIN Deglitch Thermal Comparator VIN Hysteresis: 0.03 V 2.5 µs Shutdown Leading 150°C Edge VIN UVLO Blanking Comparator Falling 100 ns and VIN BOOT Rising 3.8 V Edge sense Fet Hysteresis: 0.16 V Deglitch 30 mΩ I/O 2.5 µs SS_DIS SHUTDOWN PH LOUT Core TRACKIN Multiplexer + − R Q Adaptive Dead-Time CO and Error S Control Logic Amplifier PWM Reference Comparator 25 ns Adaptive VIN Dead Time 30 mΩ OSC PGND Powergood Comparator PWRGD VSENSE Falling 0.90 Vref Edge TPS54880 Deglitch Hysteresis: 0.03 Vref SHUTDOWN 35 µs VSENSE COMP RT RELATED DC/DC PRODUCTS (cid:1) TPS56300—dc/dc controller (cid:1) PT6600 series—6-A plugin modules 6

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 TYPICAL CHARACTERISTICS DRAIN-SOURCE INTERNALLY SET EXTERNALLY SET ON-STATE RESISTANCE OSCILLATOR FREQUENCY OSCILLATOR FREQUENCY vs vs vs JUNCTION TEMPERATURE JUNCTION TEMPERATURE JUNCTION TEMPERATURE ΩDrain Source On-State Reststance − m 1234560000000 VIN = 5 V IO = 6 A f − Internally Set Oscillator Frequency − kHz 234567555555000000−40 0 25 85 125 f − Externally Set Oscillator Frequency − kHz 234567800000000000000−40 0 RRRTTT === 61128085 00k kk 85 125 −40 0 25 85 125 TJ − Junction Temperature − °C TJ − Junction Temperature − °C TJ − Junction Temperature − °C Figure 1 Figure 2 Figure 3 VOLTAGE REFERENCE DEVICE POWER LOSSES AT TJ = 125°C OUTPUT VOLTAGE REGULATION vs vs vs JUNCTION TEMPERATURE LOAD CURRENT INPUT VOLTAGE 0.895 5 0.895 4.5 TfsJ = = 7 10205 k°CHz n − V TIOA == 38 5A°C, ge Reference − V 00..889913 wer Losses − W 23..5534 Voltage Regulatio 00..889913 fs = 550 kHz − Volta 0.889 vice Po 1.52 VI = 5 V Output 0.889 Vref0.887 De 1 V − O0.887 0.5 0.885 0 0.885 −40 0 25 85 125 0 1 2 3 4 5 6 7 8 3 3.5 4 4.5 5 5.5 6 TJ − Junction Temperature − °C IL − Load Current − A VI − Input Voltage − V Figure 4 Figure 5 Figure 6 ERROR AMPLIFIER OPEN LOOP RESPONSE 140 0 RL = 10 kΩ, −20 120 CL = 160 pF, TA = 25°C −40 100 −60 s Gain − dB468000 Phase −−−11820000ase − Degree h Gain −140P 20 −160 0 −180 −20 −200 1 10 100 1 k 10 k 100 k 1 M 10 M f − Frequency − Hz Figure 7 7

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 APPLICATION INFORMATION Figure 8 shows the schematic diagram for a typical board. To provide power up tracking, the enable of the I/O TPS54880 application. The TPS54880 (U1) can provide supply should be used. If the I/O enable is not used to greater than 8 A of output current at a nominal output power up, then devices with similar undervoltage lockout voltage of 1.8 V. For proper thermal performance, the thresholds need to be implemented to ensure power up exposed thermal PowerPAD underneath the integrated tracking. To ensure power down tracking, the enable pin circuit package must be soldered to the printed-circuit should be used. TPS54810 VOUT_I/O I/O Power Supply R1 U1 10 kΩ R2 28 1 10 RkΩ4 71.5 kΩ 2276 RETRNTAACKINVSCAEOGNMNSDPE 32 C1 R5 10R 3kΩ 25 VBIAS PWRGD4 470 pF 10 kΩ R7 C3 24 5 R6 C2 23 VIN BOOT 6 C5 C4 301 Ω 470 pF 9.76 kΩ 1 µF 22 VVIINN PPHH 7 0.047 µF 12 pF R8 21 VIN PH 8 9.76 kΩ 20 VIN PH 9 19 10 PGND PH 18 11 VOUT_CORE VIN PGND PH L1 C6 C7 1176 PGND PH 1132 R2.92 Ω 0.65 µH C8 C9 C10 10 µF 10 µF PGND PH 22 µF 22 µF 22 µF 15 PGND PH 14 C11 PwrPad 3300 pF Analog and Power Grounds are Tied at the Power Pad Under the Package of IC Figure 8. Application Circuit COMPONENT SELECTION at 1.8 V. R3, along with R7, R5, C1, C3, and C4 form the loop compensation network for the circuit. For this design, The values for the components used in this design a Type 3 topology is used. example were selected for low output ripple voltage and small PCB area. Additional design information is available at www.ti.com. OPERATING FREQUENCY INPUT FILTER In the application circuit, the 350 kHz operation is selected by leaving RT open. Connecting a 180kΩ to 68 kΩ resistor The input voltage is a nominal 5 Vdc. The input filter C6 is between RT (pin 28) and analog ground can be used to set a 10-µF ceramic capacitor (Taiyo Yuden). C7 also a 10-µF the switching frequency to 280kHz to 700 kHz. To ceramic capacitor (Taiyo Yuden) provides high frequency calculate the RT resistor, use the equation below: decoupling of the TPS54880 from the input supply and must be located as close as possible to the device. Ripple R(cid:1) 500kHz (cid:2)100[k(cid:1)] SwitchingFrequency (1) current is carried in both C6 and C7, and the return path to PGND must avoid the current circulating in the output OUTPUT FILTER capacitors C8, C9, and C10. The output filter is composed of a 0.65-µH inductor and 3 FEEDBACK CIRCUIT x 22-µF capacitor. The inductor is a low dc resistance (0.017 Ω) type, Pulse Engineering PA0227. The The values for these components have been selected to capacitors used are 22-µF, 6.3 V ceramic types with X5R provide low output ripple voltage. The resistor divider dielectric. The feedback loop is compensated so that the network of R3 and R8 sets the output voltage for the circuit unity gain frequency is approximately 75 kHz. 8

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 PCB LAYOUT input capacitors, the output capacitors, the input voltage decoupling capacitor, and the PGND pins of the Figure 9 shows a generalized PCB layout guide for the TPS54880. Use a separate wide trace for the analog TPS54880. ground signal path. This analog ground should be used for the voltage set point divider, timing resistor RT and bias The VIN pins should be connected together on the printed capacitor grounds. Connect this trace directly to AGND circuit board (PCB) and bypassed with a low ESR ceramic (pin 1). bypass capacitor. Care should be taken to minimize the loop area formed by the bypass capacitor connections, the The PH pins should be tied together and routed to the VIN pins, and the TPS54880 ground pins. The minimum output inductor. Since the PH connection is the switching recommended bypass capacitance is 10-µF ceramic with node, inductor should be located very close to the PH pins a X5R or X7R dielectric and the optimum placement is and the area of the PCB conductor minimized to prevent closest to the VIN pins and the PGND pins. excessive capacitive coupling. The TPS54880 has two internal grounds (analog and Connect the boot capacitor between the phase node and power). Inside the TPS54880, the analog ground ties to all the BOOT pin as shown. Keep the boot capacitor close to of the noise sensitive signals, while the power ground ties the IC and minimize the conductor trace lengths. to the noisier power signals. Noise injected between the two grounds can degrade the performance of the Connect the output filter capacitor(s) as shown between TPS54880, particularly at higher output currents. Ground the VOUT trace and PGND. It is important to keep the loop noise on an analog ground plane can also cause problems formed by the PH pins, Lout, Cout and PGND as small as with some of the control and bias signals. For these practical. reasons, separate analog and power ground traces are Place the compensation components from the VOUT trace recommended. There should be an area of ground one the to the VSENSE and COMP pins. Do not place these top layer directly under the IC, with an exposed area for components too close to the PH trace. Do to the size of the connection to the PowerPAD. Use vias to connect this IC package and the device pinout, they will have to be ground area to any internal ground planes. Use additional routed somewhat close, but maintain as much separation vias at the ground side of the input and output filter as possible while still keeping the layout compact. capacitors as well. The AGND and PGND pins should be tied to the PCB ground by connecting them to the ground Connect the bias capacitor from the VBIAS pin to analog area under the device as shown. The only components ground using the isolated analog ground trace. If an RT that should tie directly to the power ground plane are the resistor is used, connect it to this trace as well. 9

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 ANALOG GROUND TRACE AGND RT VSENSE ENA TRACKING VOLTAGE COMPENSATION COMP TRACKIN RESISTOR DIVIDER NETWORK BIAS CAPACITOR NETWORK PWRGD VBIAS BOOT CAPACITOR BOOT VIN EXPOSED PH POWERPAD VIN VOUT AREA PH VIN PH VIN VIN PH PH VIN PH PGND OUTPUT INDUCTOR PH PGND OUTPUT PH PGND FILTER CAPACITOR PH PGND INPUT INPUT PH PGND BYPASS BULK CAPACITOR FILTER TOPSIDE GROUND AREA VIA to Ground Plane Figure 9. TPS54880 PCB Layout 10

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 LAYOUT CONSIDERATIONS FOR THERMAL any area available must be used when 8 A or greater PERFORMANCE operation is desired. Connection from the exposed area of the PowerPAD to the analog ground plane layer must be For operation at full rated load current, the analog ground made using 0.013 inch diameter vias to avoid solder plane must provide an adequate heat dissipating area. A wicking through the vias. Eight vias must be in the 3-inch by 3-inch plane of 1 ounce copper is recommended, PowerPAD area with four additional vias located under the though not mandatory, depending on ambient temperature device package. The size of the vias under the package, and airflow. Most applications have larger areas of internal but not in the exposed thermal pad area, can be increased ground plane available, and the PowerPAD must be to 0.018. Additional vias beyond the twelve recommended connected to the largest area available. Additional areas that enhance thermal performance must be included in on the top or bottom layers also help dissipate heat, and areas not under the device package. Minimum Recommended Thermal Vias: 8 x 0.013 Diameter Inside 8 PL Ø0.0130 Powerpad Area 4 x 0.018 Diameter Under Device as Shown. Additional 0.018 Diameter Vias May Be Used if Top Side Analog Ground 4 PL Ø0.0180 Area Is Extended. Connect Pin 1 to Analog Ground Plane in This Area for Optimum Performance 0.0150 0.06 0.0339 0.0650 0.0500 0.3820 0.3478 0.0500 0.2090 0.0500 0.0256 0.0650 0.0339 Minimum Recommended Exposed Copper Area for Powerpad. 5mil 0.1700 Stencils May Require 10 Percent 0.1340 Larger Area Minimum Recommended Top Side Analog Ground Area 0.0630 0.0400 Figure 10. Recommended Land Pattern for 28-Pin PWP PowerPAD 11

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 PERFORMANCE GRAPHS EFFICIENCY LOAD REGULATION LINE REGULATION vs vs vs OUTPUT CURRENT OUTPUT CURRENT INPUT VOLTAGE 100 0.20 0.20 9905 VO = 1.8 V 0.15 VVTAIO = == 5 21 5V.8°,C V,, 0.15 VTFASO 2==5 7°1C0.80, Vk,Hz 85 % 0.10 FS = 700 kHz % 0.10 Efficiency − % 67785050 VO = 0.9 V VO = 1.2 V Load Regulation − −−000...0105005 Line Regulation − −−000...0100505 IO = 0 A IO = 6 A 60 VI = 5 V, 55 TFAS == 2750°0C k,Hz −0.15 −0.15 50 −0.20 −0.20 0.5 1 1.522.533.5 44.55 5.566.57 7.58 0 1 2 3 4 5 6 7 8 4 4.5 5 5.5 6 IO − Output Current − A IO − Output Current − A VI − Input Voltage − V Figure 11 Figure 12 Figure 13 AMBIENT TEMPERATURE vs LOOP RESPONSE LOAD CURRENT v OUTPUT AND INPUT RIPPLE 5600 115800 112155 TfsJ = = 7 10205 k°CHz 00 mV/di v Gain − dB−−1234210000000 Gain Phase −−03691000263000Phase − Degrees°mbient Temperature − C 1056789555555 Safe Operating Area(1) VI = 5 V Input Ripple − 1V/div Output Ripple − 20 mV/di −−−543000 VIfOSI === 7500 VA0,, kHz −−−11952000 A 3455 e Pin − 2 −60100 1 k 10 k 100 k 1 M−180 250 1 2 3 4 5 6 7 8 Phas t − Time − 1 µs/div f − Frequency − Hz IO − Output Current − A Figure 14 Figure 15 Figure 16 LOAD TRANSIENT RESPONSE STARTUP TIMING POWER DOWN TIMING − Output Voltage −100 mV/divVO VVIO = = 5 1 V.8, V Load Current 2A/div − Output Voltage −1 V/divVO VfsI == 750 V0 kHz PWRGPDW(IR/OG)DC(COOIR/OREE) Power Good − 5 V/div − Output Voltage −1 V/divVO CPIP/OWOWRRREGGDD((CI/OO)RE) Power Good − 5 V/div t − Time −20 µs/div t − Time − 500 µs/div t − Time −20 µs/div Figure 17 Figure 18 Figure 19 (1) Safe operating area is applicable to the test board conditions in the Dissipation Ratings 12

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 Figure 20 shows the schematic diagram for a power switch ensures the I/O voltage is not applied to the load supply tracking design using a TPS2034 high side power before U1 has enough bias voltage to operate and switch and a TPS54880 device. The TPS2034 power generate the core voltage. TPS2034 VOUT_I/O Distribution Switch R1 U1 10 kΩ R2 28 1 10 RkΩ4 71.5 kΩ 2276 RETRNTAACKINVSCAEOGNMNSDPE 32 C1 R5 10R 3kΩ 25 VBIAS PWRGD4 470 pF 10 kΩ R7 C3 24 5 R6 C2 23 VIN BOOT 6 C5 C4 301 Ω 470 pF 9.76 kΩ 1 µF 22 VVIINN PPHH 7 0.047 µF 12 pF R8 21 VIN PH 8 9.76 kΩ 20 VIN PH 9 19 10 PGND PH 18 11 VOUT_CORE VIN PGND PH L1 C6 C7 1176 PGND PH 1132 R2.92 Ω 0.65 µH C8 C9 C10 10 µF 10 µF PGND PH 22 µF 22 µF 22 µF 15 PGND PH 14 C11 PwrPad 3300 pF Analog and Power Grounds are Tied at the Power Pad Under the Package of IC Figure 20. Typical Application With Power Switch 13

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 DETAILED DESCRIPTION VOLTAGE REFERENCE The voltage reference system produces a precise V UNDERVOLTAGE LOCK OUT (UVLO) ref signal by scaling the output of a temperature stable The TPS54880 incorporates an under voltage lockout bandgap circuit. During manufacture, the bandgap and circuit to keep the device disabled when the input voltage scaling circuits are trimmed to produce 0.891 V at the (VIN) is insufficient. During power up, internal circuits are output of the error amplifier, with the amplifier connected held inactive until VIN exceeds the nominal UVLO as a voltage follower. The trim procedure adds to the high threshold voltage of 3.8 V. Once the UVLO start threshold precision regulation of the TPS54880, since it cancels is reached, device start-up begins. The device operates offset errors in the scale and error amplifier circuits. until VIN falls below the nominal UVLO stop threshold of OSCILLATOR AND PWM RAMP 3.5 V. Hysteresis in the UVLO comparator, and a 2.5-µs rising and falling edge deglitch circuit reduce the likelihood The oscillator frequency is set internally to 350 kHz. If a of shutting the device down due to noise on VIN. different frequency of operation is required for the application, the oscillator frequency can be externally TRACKIN/INTERNAL SLOW-START adjusted from 280 to 700 kHz by connecting a resistor The internal slow-start circuit provides start-up slope between the RT pin and AGND. The switching frequency control of the output voltage. The nominal internal is approximated by the following equation, where R is the slow-start rate is 25 V/ms. When the voltage on TRACKIN resistance from RT to AGND: rises faster than the internal slope or is present when SwitchingFrequency(cid:1)100k(cid:1)(cid:2)500[kHz] (2) device operation is enabled, the output rises at the internal R rate. If the reference voltage on TRACKIN rises more SWITCHING FREQUENCY RT PIN slowly, then the output rises at about the same rate as TRACKIN. 350 kHz, internally set Float Externally set 280 kHz to 700 kHz R = 180 kΩ to 68 kΩ Once the voltage on the TRACKIN pin is greater than the internal reference of 0.891 V, the multiplexer switches the ERROR AMPLIFIER noninverting node to the high precision reference. The high performance, wide bandwidth, voltage error amplifier sets the TPS54880 apart from most dc/dc ENABLE (ENA) converters. The user is given the flexibility to use a wide The enable pin, ENA, provides a digital control enable or range of output L and C filter components to suit the disable (shut down) for the TPS54880. An input voltage of particular application needs. Type 2 or type 3 compensa- 1.4 V or greater ensures that the TPS54880 is enabled. An tion can be employed using external compensation input of 0.82 V or less ensures that device operation is components. disabled. These are not standard logic thresholds, even PWM CONTROL though they are compatible with TTL outputs. Signals from the error amplifier output, oscillator, and When ENA is low, the oscillator, slow-start, PWM control current limit circuit are processed by the PWM control and MOSFET drivers are disabled and held in an initial logic. Referring to the internal block diagram, the control state ready for device start-up. On an ENA transition from logic includes the PWM comparator, OR gate, PWM latch, low to high, device start-up begins with the output starting and portions of the adaptive dead-time and control logic from 0 V. block. During steady-state operation below the current limit threshold, the PWM comparator output and oscillator VBIAS REGULATOR (VBIAS) pulse train alternately reset and set the PWM latch. Once the PWM latch is reset, the low-side FET remains on for a The VBIAS regulator provides internal analog and digital minimum duration set by the oscillator pulse width. During blocks with a stable supply voltage over variations in this period, the PWM ramp discharges rapidly to its valley junction temperature and input voltage. A high quality, voltage. When the ramp begins to charge back up, the low-ESR, ceramic bypass capacitor is required on the low-side FET turns off and high-side FET turns on. As the VBIAS pin. X7R or X5R grade dielectrics are PWM ramp voltage exceeds the error amplifier output recommended because their values are more stable over voltage, the PWM comparator resets the latch, thus temperature. The bypass capacitor must be placed close turning off the high-side FET and turning on the low-side to the VBIAS pin and returned to AGND. FET. The low-side FET remains on until the next oscillator External loading on VBIAS is allowed, with the caution that pulse discharges the PWM ramp. internal circuits require a minimum VBIAS of 2.70V, and During transient conditions, the error amplifier output external loads on VBIAS with ac or digital switching noise could be below the PWM ramp valley voltage or above the may degrade performance. The VBIAS pin may be useful PWM peak voltage. If the error amplifier is high, the PWM as a reference voltage for external circuits. latch is never reset, and the high-side FET remains on until 14

TPS54880 www.ti.com SLVS450A − OCTOBER 2002 REVISED APRIL 2005 the oscillator pulse signals the control logic to turn the OVERCURRENT PROTECTION high-side FET off and the low-side FET on. The device The cycle-by-cycle current limiting is achieved by sensing operates at its maximum duty cycle until the output voltage the current flowing through the high-side MOSFET and rises to the regulation set-point, setting VSENSE to comparing this signal to a preset overcurrent threshold. approximately the same voltage as VREF. If the error The high side MOSFET is turned off within 200 ns of amplifier output is low, the PWM latch is continually reset reaching the current limit threshold. A 100-ns leading edge and the high-side FET does not turn on. The low-side FET blanking circuit prevents the current limit from false remains on until the VSENSE voltage decreases to a tripping. Current limit detection occurs only when current range that allows the PWM comparator to change states. flows from VIN to PH when sourcing current to the output The TPS54880 is capable of sinking current continuously filter. Load protection during current sink operation is until the output reaches the regulation set-point. provided by thermal shutdown. If the current limit comparator trips for longer than 100 ns, THERMAL SHUTDOWN the PWM latch resets before the PWM ramp exceeds the error amplifier output. The high-side FET turns off and The device uses the thermal shutdown to turn off the power low-side FET turns on to decrease the energy in the output MOSFETs and disable the controller if the junction inductor and consequently the output current. This temperature exceeds 150°C. The device is released from process is repeated each cycle in which the current limit shutdown automatically when the junction temperature comparator is tripped. decreases to 10°C below the thermal shutdown trip point, and starts up under control of the slow-start circuit. DEAD-TIME CONTROL AND MOSFET Thermal shutdown provides protection when an overload DRIVERS condition is sustained for several milliseconds. With a persistent fault condition, the device cycles continuously; Adaptive dead-time control prevents shoot-through starting up by control of the soft-start circuit, heating up due current from flowing in both N-channel power MOSFETs to the fault condition, and then shutting down upon during the switching transitions by actively controlling the reaching the thermal shutdown trip point. This sequence turnon times of the MOSFET drivers. The high-side driver repeats until the fault condition is removed. does not turn on until the voltage at the gate of the low-side FET is below 2 V. While the low-side driver does not turn POWER-GOOD (PWRGD) on until the voltage at the gate of the high-side MOSFET The power good circuit monitors for under voltage is below 2 V. conditions on VSENSE. If the voltage on VSENSE is 10% The high-side and low-side drivers are designed with below the reference voltage, the open-drain PWRGD 300-mA source and sink capability to quickly drive the output is pulled low. PWRGD is also pulled low if VIN is power MOSFETs gates. The low-side driver is supplied less than the UVLO threshold or ENA is low, or a thermal from VIN, while the high-side drive is supplied from the shutdown occurs. When VIN ≥ UVLO threshold, ENA ≥ BOOT pin. A bootstrap circuit uses an external BOOT enable threshold, and VSENSE > 90% of V , the open ref capacitor and an internal 2.5-Ω bootstrap switch drain output of the PWRGD pin is high. A hysteresis connected between the VIN and BOOT pins. The voltage equal to 3% of V and a 35 µs falling edge deglitch ref integrated bootstrap switch improves drive efficiency and circuit prevent tripping of the power good comparator due reduces external component count. to high frequency noise. 15

PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 PACKAGING INFORMATION Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples (1) Drawing Qty (2) (6) (3) (4/5) TPS54880PWP ACTIVE HTSSOP PWP 28 50 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 85 TPS54880 & no Sb/Br) TPS54880PWPR ACTIVE HTSSOP PWP 28 2000 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 85 TPS54880 & no Sb/Br) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1

PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 12-Feb-2019 TAPE AND REEL INFORMATION *Alldimensionsarenominal Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1 Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant (mm) W1(mm) TPS54880PWPR HTSSOP PWP 28 2000 330.0 16.4 6.9 10.2 1.8 12.0 16.0 Q1 PackMaterials-Page1

PACKAGE MATERIALS INFORMATION www.ti.com 12-Feb-2019 *Alldimensionsarenominal Device PackageType PackageDrawing Pins SPQ Length(mm) Width(mm) Height(mm) TPS54880PWPR HTSSOP PWP 28 2000 350.0 350.0 43.0 PackMaterials-Page2

GENERIC PACKAGE VIEW PWP 28 PowerPADTM TSSOP - 1.2 mm max height 4.4 x 9.7, 0.65 mm pitch SMALL OUTLINE PACKAGE Images above are just a representation of the package family, actual package may vary. Refer to the product data sheet for package details. 4224765/A www.ti.com

None

None

None

IMPORTANTNOTICEANDDISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2020, Texas Instruments Incorporated