DATA SHEET SE2431L: 2.4 GHz Front-End Module Applications L E S _ SXDT  Smart meters CPCTCSAN  In-home appliances Logic  Smart thermostats Control PA Features ANT1  Integrated: – PA with up to +24 dBm output power TR – LNA with programmable bypass – Antenna switching with Tx and Rx diversity function ANT2  Suitable for ZigBee®, Bluetooth® Low Energy, and Bluetooth 1.0 LNA  Typical low NF: 2 dB 202410-001  Operating temperature range: –40 °C to +125 °C Figure 1. SE2431L Block Diagram  Single-ended 50 Ω Tx/Rx RF interface  Fast switch on/off time <1 μs Description  Supply operation: 2.0 V to 3.6 V The SE2431L is a high-performance, fully integrated RF front-end  Sleep mode current: 0.05 μA typical module (FEM), suitable for ZigBee, Bluetooth Low Energy, and  Small QFN (24-pin, 3.0 mm x 4.0 mm x 0.9 mm Nickel- Bluetooth 1.0 applications. Palladium-gold [NiPdAu] plated) package The SE2431L is designed for ease of use and maximum flexibility, (MSL1, 260°C per JEDEC J-STD-020) with fully matched 50 Ω input and output, integrated inter-stage matching and harmonic filter, and digital controls that are compatible with 1.6 V to 3.6 V Complementary Metal Oxide Semiconductor (CMOS) levels. Skyworks GreenTM products are compliant with The RF blocks operate over a wide supply voltage range from all applicable legislation and are halogen-free. 2.0 V to 3.6 V, which allows the SE2431L to be used in battery- For additional information, refer to Skyworks powered applications over a wide spectrum of the battery Definition of GreenTM, document number discharge curve. SQ04–0074. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202410K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 13, 2017 1

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE T 1 X U C S D T O C P S C B V C C 4 3 2 1 0 2 2 2 2 2 B2 1 19 VCC2 B1 2 18 GND N/C 3 17 N/C N/C 4 16 ANT_SEL N/C 5 15 ANT1 T/R 6 14 GND N/C 7 13 ANT2 8 9 10 11 12 C D D D D Y0587 N/ GN GN GN GN Figure 2. SE2431L Pinout (Top View) Table 1. SE2431L Signal Descriptions Pin Name Description Pin Name Description 1 B2 Connect through the bias resistor to pin 23 13 ANT2 Connect to 50 Ω antenna 2 B1 Connect through the bias resistor to pin 23 14 GND Connect to PCB ground 3 N/C Not connected internally to the device 15 ANT1 Connect to 50 Ω antenna 4 N/C Not connected internally to the device 16 ANT_SEL Connect to the GPIO signal to control the antenna switch (see Table 8) 5 N/C Not connected internally to the device 17 N/C Not connected internally to the device 6 Transmit/receive port from/to transceiver, T/R 18 GND Connect to PCB ground single-ended 50 Ω 7 N/C Not connected internally to the device 19 VCC2 Connect to positive supply 8 N/C Not connected internally to the device 20 CSD Connect to the GPIO signal to control the SE2431L modes (see Table 8) 9 GND Connect to PCB ground 21 CPS Connect to the GPIO signal to control the SE2431L modes (see Table 8) 10 GND Connect to PCB ground 22 VCC1 Connect to positive supply 11 GND Connect to PCB ground 23 BOUT Connect to pins 1 and 2 through the bias resistors 12 GND Connect to PCB ground 24 CTX Connect to the GPIO signal to control the SE2431L modes (see Table 8) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 June 13, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410K

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Electrical and Mechanical Specifications The absolute maximum ratings of the SE2431L are provided in The state of the SE2431L is determined by the logic provided in Table 2. The recommended operating conditions are specified in Table 8. Table 3, and electrical specifications are provided in Tables 4 through 7. Table 2. SE2431L Absolute Maximum Ratings1 Parameter Symbol Minimum Maximum Units Supply voltage 1 VCC1 –0.3 3.6 V Supply voltage 2 VCC2 –0.3 3.6 V Control pin voltages –0.3 3.6 V Operating temperature TOP –40 +125 C Storage temperature TSTG –40 +125 C Tx output power at ANT1 or ANT2 port into 50 Ω load POUT_TX_MAX +24 dBm Tx input power at TR port PIN_TX_MAX +6 dBm Rx input power at ANT1 or ANT2 ports PIN_RX_MAX +10 dBm Rx input power at ANT1 or ANT2 ports in bypass mode PIN_RX_BYPASS_MAX +15 dBm Thermal resistance ΘJC 40 C/W Electrostatic discharge: ESD Human Body Model (HBM), Class 1C 1000 V 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD handling precautions should be used at all times. Table 3. Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Ambient temperature TA –40 +25 +125 C Supply voltage on VCC pins VCC1 2.0 3.0 3.6 V Supply voltage on VCC pins VCC2 2.0 3.0 3.6 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202410K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 13, 2017 3

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Table 4. SE2431L Electrical Specifications: DC1 (VCC = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Total supply current ICC_TX20 Tx mode POUT = +20 dBm 115 mA Total supply current2 ICC_TX17 Tx mode POUT = +17 dBm 90 mA Total supply current2 ICC_TX10 Tx mode POUT = +10 dBm 50 mA Quiescent current ICQ_TX No RF 30 mA Total supply current ICC_RX Rx mode 5 7 mA Total supply current ICC_RXBYPASS Rx Bypass mode 300 μA Sleep supply current ICC_OFF No RF 0.05 1.0 μA 1 Performance is guaranteed only under the conditions listed in the above table. 2 Guaranteed by characterization. Table 5. SE2431L Electrical Specifications: Logic Characteristics1 (VCC = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Logic input high voltage2 VIH 1.6 3.6 V Logic input low voltage2 VIL 0 0.3 V Logic input high current2 IIH 1 μA Logic input low current2 IIL 1 μA 1 Performance is guaranteed only under the conditions listed in the above table. 2 Guaranteed by characterization. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 June 13, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410K

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Table 6. SE2431L Electrical Specifications: AC Characteristics1 (VCC = 3 V, TA = +25 C, as Measured on Skyworks SE2431L-EK1 Evaluation Board [De-Embedded to the Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Transmit (Tx) Frequency range fIN 2400 2483 MHz POUT VCC = +3.6 V, PIN = +3 dBm5 +24.0 dBm VCC = +3.3 V, PIN = 0 dBm5 +22.5 dBm VCC = +3.0 V, PIN = 0 dBm +21.0 dBm Output power at ANT1 or ANT2 ports VCC = +2.7 V, PIN = 0 dBm5 +20.5 dBm VCC = +2.0 V, PIN = 0 dBm +17.0 dBm VCC = +3.0 V, PIN = –13 dBm5 +10 dBm Small signal gain S21 2400 MHz to 2483 MHz, PIN = -25 dBm 19 22 25 dB Small signal gain variation ΔS21 2400 to 2483 MHz 2 dBp-p Saturated gain variation5 ΔGSAT 2400 to 2483 MHz 1 dBp-p Harmonics2 HD2 POUT = +20 dBm –42 dBm/MHz HD35 POUT = +20 dBm –42 dBm/MHz Output return loss5 S22_ANT At ANT1 or ANT2 ports –10 –5 dB Input return loss5 S11 At TR port, Tx mode –5 dB Rise and fall times5 ttRF43 800 ns Stability5 STAB C0.W1 ,G PHINz =to 0 2 d0B.0m G Hz All non-harmonically related outputs <–42.0 dBm/MHz Load VSWR = 6:1 Ruggedness5 RU CW, PIN = +6 dBm, Load VSWR = 10:1 No permanent damage Receive (Rx) Frequency range fIN 2400 2483 MHz Receive gain Rx_GAIN 10.0 12.5 15.0 dB Receive noise figure5 NF 2.0 2.5 dB Third order input intercept point5 IIP3 –3 +2 dBm LNA input compression point5 IP1dB –13 –8 dBm Antenna port return loss5 S11_ANT –10 –5 dB Output return loss5 S22 At TR port, Rx mode –10 –5 dB Rise and fall times5 tR3 800 ns tF4 Bypass gain G_BP –3 –2 dB Tx or Rx Bypass 1 dB input compression point5 IP1dB +15 dBm 1 Performance is guaranteed only under the conditions listed in the above table. 2 IEEE 802.15.4 source. 3 From 50% of the CTX edge to 90% of the final RF output power. 4 From 50% of the CTX edge to 10% of the final RF output power. 5 Guaranteed by characterization. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202410K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 13, 2017 5

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Table 7. SE2431L Electrical Specifications: AC Characteristics, Diversity Antenna Function1 (VCC1 = VCC2 = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Min Typical Max Units Isolation between ANT1 and ANT2 ports ISOLANTSW –20 dB Antenna 1 to antenna 2 switching time2 tANT1-ANT2 400 ns 1 Performance is guaranteed only under the conditions listed in the above table. Unused antenna port should be connected to 50 Ω. 2 Guaranteed by characterization. Table 8. SE2431L Logic Controls1 (VCC = 3 V, TA = +25 C, Unless Otherwise Noted) Mode Description CPS CSD CTX ANT_SEL 0 All off (sleep mode)2 0 0 0 X 1 Rx or Tx bypass mode 0 1 0 X 2 Rx LNA mode 1 1 0 X 3 Tx mode X 1 1 X ANT1 port enabled X 1 X 0 ANT2 port enabled X 1 X 1 1 The logic 0 and 1 levels are compliant to VIL and VIH, respectively, as specified in Table 5. 2 All controls must be at logic 0 to achieve the specified sleep current. Evaluation Board Description Measure TX Performance The SE2431L Evaluation Board is used to test the performance of Apply an RF signal to connector J34 (TR) to monitor the 2.4 GHz the SE2431L front-end module (FEM). An Evaluation Board amplifier performance. Monitor the output power on connector schematic diagram is provided in Figure 3. A reference design J35 (ANT1) or J32 (ANT2). schematic is shown in Figure 4. A photograph of the Evaluation Board is shown in Figure 5. A Bill of Materials (BOM) for the Measure RX Performance Evaluation Board is provided in Table 9. Apply an RF signal to connector J35 (ANT1) or J32 (ANT2) to monitor the 2.4 GHz LNA performance. Monitor the output signal Evaluation Board Setup Procedure on connector J34 (TR). Connect Supply CAUTION: Be careful not to overdrive the amplifier by applying 1. Connect J32, J34, and J35 to 50 Ω instruments. Terminate all too much RF on the input to the device. A suitable unused ports (if applicable) with 50 Ω. starting input power is –20 dBm. 2. Connect the supply ground to pin 20 of the J36 header. 3. Connect 3.0 V to pins 1, 3, and 16 of J36. 4. Refer to Table 8 for information about selecting the required RF path and for antenna port control. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 June 13, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410K

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE J36 VCC 1 2 VCC VDD 3 4 VDD 5 6 C51 2.2 uF C52 VBIN 7 8 VBIN 2.2 uF 9 10 CTX 11 12 CPS 13 14 CSD VCC 15 16 VCC2 C53 17 18 ANTSEL DNI 19 20 CPS C54 CSD R44 10 pF 100 kΩ R47 100 kΩ CTX VCC2 R43 100 kΩ BOUT R37 BOUT 2.2 kΩ C33 100 nF 25 2423222120 1.R24 k2Ω 1 B2PAD CTXBOUTVCC1CPSCSDVCC2 19 LD2N0I 1C04 p6F 2 B1 GND 18 (shorted) 3 DNC SE2431L DNC 17 4 DNC U4 ANT_SEL 16 C29 VBIN 5 DNC ANT1 15 DNI SJM34A 6 T/R GND 14 7 DNC ANT2 13 ANTSEL DNCGNDGNDGNDGND RD4N5I 89101112 TP1 Test Point J35 SMA J32 SMA 202410-003 Figure 3. SE2431L Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202410K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 13, 2017 7

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE VCC C1 2.2 uF VCC C3 C2 CTX 10 pF 100 nF CPS C4 BOUT CSD 10 pF BOUT R1 25 2423222120 L20 2.2 kΩ PAD CTX BOUT VCC1 CPS CSD D(sNhoIrted) 1 B2 VCC219 R 2 32 BD1NC SE2U4131L GDNNDC1178 1.2 kΩ 4 DNC ANT_SEL16 ANT_SEL 5 DNC ANT115 ANT1 T/R 6 T/R GND14 7 DNC ANT213 NC ND ND ND ND ANT2 D G G G G 89 101112 TP1 Test Point 202410-004 Figure 4. SE2431L Reference Design Schematic Figure 5. SE2431L Evaluation Board Notes to Figure 5: 1. R44, R45, R43, R47, and C52 are for evaluation purposes and can be removed in the final application. 2. The Skyworks Evaluation Board contains 0 Ω resistors and footprints for non-populated components that are not shown in the schematic. 3. L20 is an 0402 SMT placement with the pads shorted together. This provides 3 mm of track between the Vcc2 pin and C46. It should be included in the application layout. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 June 13, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410K

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Table 9. SE2431L Bill of Materials (BOM) Component Value Manufacturer Mfr Part Number Package Size Description R42 1.2 kΩ Panasonic ERJ2GEJ122 0402 Thick film chip resistor R37 2.2 kΩ Panasonic ERJ2GEJ222 0402 Thick film chip resistor J36 10X2 Samtec TSW-110-07-G-D 100MIL 100 mil header C33 100 nF Murata GRM155R71C104KA88D 0402 Monolithic ceramic U4 SE2431L Skyworks Skyworks SE2431L QFN400X300 2.5 GHz ZigBee front end C51, C52 2.2 uF Murata GRM21BR71A225KA01L 0805 Ceramic capacitor 2.2 uF 10 V 10% X7R C46, C54 10 pF Murata GRM1555C1H100JZ01 0402 Multilayer ceramic R43, R44, R47 100 kΩ Panasonic ERJ2GEJ104 0402 Thick film chip resistor J32, J34, J35 SMA Johnson Components 142-0701-851 End launch SMA end launch straight jack receptacle - tab contact C29, C53, R45 DNI - - 0402 Do not install L20 Short - - 0402 Shorted 0402 footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202410K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 13, 2017 9

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Package Dimensions Package and Handling Information The PCB layout footprint for the SE2431L is provided in Figure 6. Instructions on the shipping container label regarding exposure to A typical part marking diagram is shown in Figure 7. Package moisture after the container seal is broken must be followed. dimensions are shown in Figure 8, and tape and reel dimensions Otherwise, problems related to moisture absorption may occur are provided in Figure 9. when the part is subjected to high temperatures during solder assembly. The SE2431L is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C, and can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 June 13, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410K

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE 4.40 2.70 3X 1.05 3X 0.52 0 3X 0.52 3X 1.05 5X 0.54 1.70 3.40 0 0 5X 0.54 0.60 Typ 0 15X ø0.254 0.20 Typ 0.400 Typ Via Pattern Board Metal (Note 4) 4.50 4.40 2.50 1.03 0.20 Typ Typ 0.53 Typ 1.50 3.50 3.40 0.20 Typ 0.70 Typ 0.60 Typ 0.30 Typ 0.400 Typ 0.20 Typ 0.400 Typ Package Outline Solder Mask Pattern Stencil Pattern (Note 6) (Note 5) Notes: 57% Solder Coverage on Center Pad 1. All dimensions are in millimeters. 2. Dimensions and tolerances per ASME 14.5M–1994. 3. Unless specified, dimensions are symmetrical about center lines. 4. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), via holes to be filled with conductive paste and plated over. 5. Stencil recommendations: 0.10 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release. 6. Solder mask recommendations: Contact board fabricator for recommended solder mask offset and tolerance. 202410-006 Figure 6. PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202410K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 13, 2017 11

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Terminal Finish Symbol Pin 1 Indicator Skyworks Part Number Lot Code 202410-007 Figure 7. SE2431L Typical Part Marking 3.00 ± 0.05 A 0.05 C 0.85 ± 0.05 1.60 ± 0.05 0.203 Ref B 0.30 x 45° 0.00–0.05 Pin 1 Indicator Pin 1 Indicator Exposed Pad 4.00 ± 0.05 2.60 ± 0.05 0.40 24 X 0.25 Min R0.075, Typ 2X 0.05 C 25X 0.05 C See Detail A See Detail B 2X 0.05 C 4 Top View C Bottom View SeatingPlane Side View Detail B Scale 2X 0.12 ± 0.05 2X R0.075 4 Places Notes: R0.075 Detail A 1. Dimensions are in millimeters. 0.40 ± 0.05 Scale 2X 0.40 ± 0.05 0.28 ± 0.05 2. Dimensions and tolerances according to ASME Y14.5M-1994. 20 Places 3. Unless otherwise specified, the following values apply: Decimal Tolerance: Angular Tolerance: 0.20 ± 0.05 0.07 C A B 0.20 ± 0.05 0.07 C A B X.X (1 place) ± 0.1 mm ±1/2° 5 0.05 C 5 0.05 C X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm 4. Coplanarity applies to the terminals as well as all other bottom surface metallization. 5. Dimension applies to metallized terminal. If terminal tip has a radius, dimension should not be measured in that radius area. 202410-008 6. Unless specified, dimensions are symmetrical about center lines. Figure 8. SE2431L Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 12 June 13, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410K

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE 8.00 ∅1.5 +0.1/–0.0 4.00 (Note 1) 1.75 ± 0.10 2.00 ± 0.05 (Note 3) ∅1.50 Min. A 0.30 ± 0.05 5 R0.3 Max. 5.50 ± 0.0(Note 3) 0 ± 0.30 4.40 2. 1 A 0.12 1.10 3.40 Pin 1 Indicator Detail A 0.12 Notes: R0.25 1. 10 sprocket hole pitch cumulative tolerance ±0.2 mm. 2. Camber in compliance with EIA 481. 3. Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole. 202410-009 4. All measurements are in millimeters. Figure 9. SE2431L Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202410K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 13, 2017 13

DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Ordering Information Model Name Manufacturing Part Number Evaluation Board Part Number SE2431L: 2.4 GHz Front-End Module SE2431L SE2431L-EK1 Copyright © 2012-2015, 2017 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 14 June 13, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410K