CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PLG Radial Lead Type, Higher Capacitance Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105°C. Radial lead type : PLG Lead free flow soldering condition correspondence Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). Higher Capacitance PLF Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 330 to 3900µF Capacitance Tolerance ±20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Temperature Characteristics Z+105°C / Z+20°C 1.25 (100kHz) (Max.Impedance Ratio) Z–55°C / Z+20°C 1.25 Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value Endurance capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 2000 hours at 105°C. Leakage current ( 2) Less than or equal to the initial specified value Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is (Steady State) applied for 1000 hours at 60°C, 90% RH. ESR ( 1) 150% or less than the initial specified value Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions prescribed Capacitance change Within ± 10% of the initial capacitance value ( 3) Resistance to here as preheat at 150 to 200°C for 60 to 180 seconds and peak tan δ 130% or less than the initial specified value temperature at 265°C for 10 seconds or less, the capacitor shall meet ESR ( 1) 130% or less than the initial specified value Soldering Heat the specifications listed at right, provided that its temperature profile is Leakage current ( 2) Less than or equal to the initial specified value measured at both of terminal ends facing the soldering side. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 4V 1200µF) Capacitance Resin coated Case 1 2 3 4 5 6 7 8 9 10 11 12 Voltage(g:4V) P L G 0 G 1 2 2 M CO 1 LG1200g841 D±0.5φ ±0.5P Size code Configuration φd Capacitance tolerance (±20%) Series Lot. No. L+0.5MAX. 15MIN 4MIN Rated capacitance (1200µF) Rated voltage (4V) Series name (mm) Type Size φ8 × 9L φ8 × 12L φ10 × 13L φD 8.0 8.0 10.0 Voltage Frequency coefficient of rated ripple current L 8.5 11.5 12.5 V 2.5 4 6.3 10 16 P 3.5 3.5 5.0 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more φd 0.6 0.6 0.6 Code e g j A C Coefficient 0.05 0.30 0.70 1.00 Please refer to page 20 about the end seal configuration. Dimension table in next page. 66

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PLG Dimensions Rated Voltage ESR Rated Ripple (V) Surge Voltage Rated Capacitance Case Size tan δ Leakage Current (mΩ) (mArms) Part Number Code (V) (µF) φD × L (mm) (µA) (at 100kHz 20°C) (105°C/100kHz) 1800 8 × 9 0.08 900 9 6000 PLG0E182MCO1 2.5 2200 8 × 12 0.08 1100 8 6700 PLG0E222MDO1 2.8 (0E) 2700 10 × 13 0.08 1350 8 5560 PLG0E272MDO1 3900 10 × 13 0.08 1950 8 7000 PLG0E392MDO1 1200 8 × 9 0.08 960 9 5900 PLG0G122MCO1 4 4.6 1800 8 × 12 0.08 1440 9 6500 PLG0G182MDO1 (0G) 2700 10 × 13 0.08 2160 8 6900 PLG0G272MDO1 820 8 × 9 0.08 1033 9 5700 PLG0J821MCO1 6.3 1200 8 × 12 0.08 1512 9 6100 PLG0J122MDO1 7.2 (0J) 1500 10 × 13 0.08 1890 9 6300 PLG0J152MDO1 1800 10 × 13 0.08 2268 8 6600 PLG0J182MDO1 560 8 × 9 0.08 1120 11 5100 PLG1A561MCO1 10 11.5 820 8 × 12 0.08 1640 10 5800 PLG1A821MDO1 (1A) 1200 10 × 13 0.08 2400 9 6200 PLG1A122MDO1 330 8 × 9 0.08 1056 13 4700 PLG1C331MCO1 16 18.4 470 8 × 12 0.08 1504 11 5400 PLG1C471MDO1 (1C) 820 10 × 13 0.08 2624 11 5600 PLG1C821MDO1 Rated ripple current (mArms) at 105°C 100kHz Please refer to page 20, 21, 22 about the formed or taped product spec. Please refer to page 3 for the minimum order quantity. 67

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N ichicon: PLG1C471MDO1 PLG1C821MDO1 PLG1A821MDO1 PLG1A561MCO1 PLG0E392MDO1 PLG1C331MCO1 PLG0E222MDO1 PLG0G122MCO1 PLG0G182MDO1 PLG0G272MDO1 PLG0J122MDO1 PLG0J182MDO1 PLG0J821MCO1 PLG1A122MDO1 PLG0E182MCO1 PLG0J152MDO1 PLG0E272MDO1TD PLG0E392MD01 PLG0E272MDO1 PLG0G272MDO1TD PLG1A821MDO1TD PLG1C471MDO1TD PLG1A122MDO1TD PLG1C331MCO1TD PLG0J821MCO1TD PLG0J182MDO1TD PLG0J122MDO1TD PLG0E392MDO1TD PLG1A561MCO1TD PLG0G122MCO1TD PLG1C821MDO1TD PLG0E182MCO1TD PLG0E222MDO1TD PLG0G182MDO1TD PLG0J152MDO1TD