DDLLPP--RRFFIIDD-- LLPP88CC LEAD-FREE 88--CChhaannnneell RReeaaddeerr//WWrriitteerr FEATURES: • ISO15693, ISO14443A, ISO14443B Compatible • Can read the UID/SID of up to 15 Tags Simultaneously • 13.56MHz Reader/Writer • 8 Channels for External Antenna Connections • FCC/IC Modular Approvals in Place • USB Port Powered from Windows, CE or Linux PC • Both USB and RS232 Interfaces Provided • USB Interface; No Driver Development Required for Windows, CE or Linux PC • Operating Temperatures: 0°C to 70°C • Dimensions: (L x W x H) 4.36” x 3.32” x 0.6” APPLICATIONS INCLUDE: • Real-Time Security • Personal Identification • Pharmaceutical Tracking • Inventory/Asset Management & Tracking • Library/Book Management & Tracking • Baggage Tagging • Sports Event Timing 1.0 INTRODUCTION The DLP-RFID-LP8C is a low-cost, USB-powered module for reading from and writing to ISO15693, ISO14443A and ISO14443B intelligent RFID transponder tags via up to eight external antennas. It has the ability to both read and write tag user data in addition to reading the unique identifier (UID). All of the DLP-RFID-LP8C’s electronics reside on a single, compact PCB; and all operational power is taken from the host Windows/Windows CE/Linux PC via the USB interface. Up to eight external antennas can be connected via reverse-polarity SMA connectors. Rev. 1.7 (May 2018) 1 © DLP Design, Inc.

2.0 HARDWARE SETUP The four jumpers provided on the DLP-RFID-LP8C module are used to select between the USB and Rs232 interfaces. For RS232 interface operation, move the three jumpers to the RS and RS232 positions and remove JP3. For USB operation, move the three jumpers to the USB position and add jumper JP3. If using the RS232 interface, connect the J3 wiring terminals to ±8V to ±12V serial signals typically found in the DB9, RS232 port connectors on a host PC. An external, regulated 5 volt power source must also be connected to J2. If using USB, simply connect the DLP-RFID-LP8C to a host PC using the 5-pin mini-B USB connector CN1 and a compatible USB cable. All power and data are provided via the USB cable. 3.0 APPLICATION DEVELOPMENT The serial interface for the DLP-RFID-LP8C operates at 115,200 baud, no parity, 8 data bits and 1 stop bit. A demonstration GUI is provided with the purchase of a DLP-RFID-LP8C module that demonstrates the communications protocols. Using the Virtual COM Port USB drivers, the DLP-RFID-LP8C appears to the host PC (Windows, Linux, Mac) as an RS232 port. The GUI presents the actual control packets sent, and the reply data coming back from the DLP-RFID-LP8C as an aid to the software developer. 3.1 DEMONSTRATION GUI The demonstration GUI is available as a free download from the DLP Design website. The URL for the download page is printed on the outer packaging of the DLP-RFID-LP8C. Rev. 1.7 (May 2018) 2 © DLP Design, Inc.

3.2 LP8C SPECIFIC COMMANDS To select one of the 8 external antennas on the DLP-RFID-LP8C you must send the correct command packet (Ex: 010900030422F00000). To send this packet using the TI GUI, first make the connection to the DLP-RFID-LP8C, and then click on the Test tab. Enter a command packet as shown below and click on Send Raw. The LED associated with the antenna channel selected will light and successive tag reads will use that channel. LP8C Specific commands: Commands to activate 1 of the 8 Antenna Channels: 1. 010900030422F00000 2. 010900030423F00000 3. 010900030424F00000 4. 010900030425F00000 5. 010900030426F00000 6. 010900030427F00000 7. 010900030428F00000 8. 010900030429F00000 Read Opto-isolated inputs: 010900030435F00000 Write opto-isolated output 1 high: 010900030430F00000 Write opto-isolated output 1 low: 010900030431F00000 Write opto-isolated output 2 high: 010900030432F00000 Write opto-isolated output 2 low: 010900030433F00000 Issue Pass beep 010900030477F00000 Issue Fail Beep 010900030479F00000 Rev. 1.7 (May 2018) 3 © DLP Design, Inc.

3.3 LP8C OPERATING FIRMWARE The source code for the firmware running in the DLP-RFID-LP8C reader (developed using Code Composer Studio) is available for download upon purchase of the DLP-RFID-LP8C from the DLP Design website. 4.0 MECHANICAL DIMENSIONS IN INCHES (MM) 2.08 typ (53.0 typ) 0.45 typ (11.4typ) 0.12 typ (3.1 typ) 0.60 typ (15.1 typ) 0.37 typ (9.3 typ) 3.0 typ 1.55 typ (76.2typ) (39.4typ) 2.70 typ (68.6typ) 3.84 typ (97.6typ) 4.36 typ (111 typ) 2.75 typ (68.9 typ) 3.32 typ 2.85 typ (84typ) (72.3typ) Rev. 1.7 (May 2018) 4 © DLP Design, Inc.

5.0 REGULATORY AGENCY CONSIDERATIONS 5.1 AGENCY IDENTIFICATION NUMBERS Compliance with the appropriate regulatory agencies is essential in the deployment of all intentional radiators. DLP Design has obtained modular approval for this RF product such that an OEM need only meet a few basic requirements in order to utilize their end product under this approval. Corresponding agency identification numbers are listed below: PPAARRTT NNUUMMBBEERR UUSS//FFCCCC CCAANN//IICC DLP-RFID-LP8C SX90LP8C 5675A-0LP8C 5.2 EXTERNAL ANTENNAS The DLP-RFID1-LP8C is approved for use with external 50 Ohm loop/ferrite antennas that are resonant at 13.56MHz. Connection is made via reverse-polarity SMA connectors. Two different antennas are available from DLP Design: the DLP-FANT and the DLP-RFID-ANT. DDLLPP--FFAANNTT DDLLPP--RRFFIIDD--AANNTT The DLP-FANT ferrite-based antenna provides a compact footprint for space-constrained applications and provides up to a 1.25-inch read range. The DLP-FANT requires a coax cable with a reverse-polarity SMA connector at one end for connection to the DLP-RFID-LP8C reader. This coax cable is available in a 3-foot length from DLP Design under part number DLP-COAX1. The DLP-RFID-ANT ships with an attached 15-foot coax cable with a reverse-polarity SMA connector and provides up to 4 inches of read range with larger (credit card size) tags. Rev. 1.7 (May 2018) 5 © DLP Design, Inc.

5.3 FCC/IC REQUIREMENTS FOR MODULAR APPROVAL Any changes or modifications to the DLP-RFID-LP8C’s printed circuit board could void the user’s authority to operate the equipment. Operation of an unapproved antenna could void the user’s authority to operate the equipment. 5.4 WARNINGS Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) this device must accept any interference received, including interference that may cause undesirable operation. To reduce potential radio interference with other users, the antenna type and its gain should be so chosen that the equivalent isotropically-radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device is intended for use under the following conditions: 1. The transmitter module may not be co-located with any other transmitter or antenna; and, 2. The module is approved using the FCC “unlicensed modular transmitter approval” method. As long as these two conditions are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance measures necessitated by the installation of this module (i.e. digital device emissions, PC peripheral requirements, etc.). Note: In the event that these conditions cannot be met (i.e. co-location with another transmitter), then the FCC authorization is no longer valid, and the corresponding FCC ID may not be used on the final product. Under these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 5.5 OEM PRODUCT LABELING The final end product must be labeled in a visible area with the following text: “Contains TX FCC ID: SX90LP8C” 5.6 RF EXPOSURE In order to comply with FCC RF exposure-compliance requirements, the antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Rev. 1.7 (May 2018) 6 © DLP Design, Inc.

5.7 ADDITIONAL INFORMATION FOR OEM INTEGRATORS The end user should NOT be provided with any instructions on how to remove or install the DLP-RFID- LP8C. This device has been pre-certified to operate with the antenna models listed below, or any other 50 Ohm, magnetic loop antenna that resonates at 13.56MHz. (cid:131) DLP Design Large Loop Antenna (cid:131) DLP Design Small Loop Antenna (cid:131) DLP Design Ferrite Antenna 6.0 DISCLAMER Neither the whole nor any part of the information contained herein nor the product described in this datasheet may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis, and no warranty as to their suitability for any particular purpose is either made or implied. DLP Design will not accept any claim for damages whatsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. 7.0 CONTACT INFORMATION DLP Design, Inc. 1605 Roma Lane Allen, TX 75013 Phone: 469-964-8027 Fax: 415-901-4859 Email: support@dlpdesign.com Internet: http://www.dlpdesign.com Rev. 1.7 (May 2018) 7 © DLP Design, Inc.

A B C D C C C C C C C C H H H H H H H H 8 901-144-8RRP-SMA8 6 901-144-8RRP-SMA6 4 901-144-8RRP-SMA4 2 901-144-8RRP-SMA2 7 901-144-8RRP-SMA7 5 901-144-8RRP-SMA5 3 901-144-8RRP-SMA3 1 901-144-8RRP-SMA1 5 3241FXRELAY SPSTRL8 3241FXRL6RELAY SPST 3241FXRL4RELAY SPST 3241FXRL2RELAY SPST 3241FXRELAY SPSTRL7 3241FXRL5RELAY SPST 3241FXRL3RELAY SPST 3241FXRL1RELAY SPST 5 S S W W V V C C C C 360R8 LEDD2 360R4 LEDD1 360R5 LEDD4 360R1 LEDD3 360R6 LEDD6 360R2 LEDD5 360R7 LEDD8 A 360R3 LEDD7 N SWVC TENNA SWVC 10111213141516 C 10111213141516 C 4 SWVCC8 COMG9ND7C7B76B6C65B5C54B4C43B3C32B2C21B1C1 ULN2003A/TSSOPU4 SWVCC8 COMG9ND7B7C76B6C65B5C54B4C43B3C32B2C21B1C1 ULN2003A/TSSOPU3 4 3 .47uFC22 54321 Mini-B USB ConnectorCN1 RS232 HeaderJ3 4321 8 Y7G7NY6G2B95DY5G2A104Y4G1116Y312CY2313BY1V214CAY0115C 16 UCVCC0.1uFC18 3 47pF47pFC13C12 10/10 Tant.01C10C11 12 240-1018-1FB1 DTR -->RX <--TX --> 0.1uFC2 0.1uFC1 UCVCC ANT_SEL_CANT_SEL_BANT_SEL_A5VDC INJ274HC238/TSSOPU5 21 5 V 2 FT232R712228156.1uFC16GGGATEGNNN3V3OUTSN17DDDTD OSCO28OSCI27AVCC/NC24RESET#19VCCIN/NC8 USBDP15USBDMV16CCVCC5 INIO20 FT232R4 U8 .1uFC14 MAX3238/SO FORCEOFF14FORCEON13INVALID15 R1OUTB16T5INT5OUT1712R3INR3OUT1118T4INT4OUT1910R2INR2OUT920R1INR1OUT821T3INT3OUT227T2INT2OUT236T1INT1OUT245 C1-25VCCV-264C2-3GNDV+227C1+C2+281U60.1uF C5 0.1uF/0603C21 10/10 TantC19 .01uFC20 12IN1uF/10V/0603C8240-1018-1FB2 2 1 CBUS412CBUS314CBUS213CBUS122CBUS02347KRI#6R23DCD#10DSR#9MMBT3904DTR#2Q4CTS#11.1uFRTS#3C9RXD5TXD1 30KR21 UCVCC.1uFC15 USBVCC IRLML6402CT PQ3 1RX <--TOHOSTRX <--RX Select 10K MMBT3904Q5R30RESET TX -0.1uF-C4360>R28 TX -->1 FROMHOST 0.1uFC3LEDTX SELECTD9 USBVCCSWVCC 15V SELECT .01uF/06032C7 GNCINCOUT31D10/10 TantC6 INOUT453.3V PQ1L303M2SPU7 1 A B C D

A B C D EXT_O EXT_O U U T2 T1 5 1.8KR34 1.8KR36 3V 5 C C LTV846ISO 8 76 54 32 1470R32 470R33 1 9 1011 1213 1415 16 C 46 E E 4 S 22pF XT_IN1 XT_IN2 10KR314 2.2uFC33 WVCC 3VCC 13.56MHY1 10KR35 z 0.01uFC34 BG11 VSS10 RX2_PM9 RX1_AM8 VSS_RX7 VSS_PA6 TX_OUT5 VDD_PA4 VDD_RF3 VIN2 VDD_A1 VDD_X32 XTAL_IN31 XTAL_OUT30TRF7970AU1 C4722pF filtrationetwork &Matching 3VCC n D ASK/OOK IRQ MOD VSS_AVSS_DVDD_IO IO0IO1IO2IO3IO4IO5IO6IO7 EN2ATA_CLK SYS_CLK EN 12 13 14 152916 1718192021222324 2526 27 28 AN TE 321 21 N 3 3VCC 3VCC SLAVE_SELE SOMISIMO SWVCCDATA_CLK NA J4 COMIN2IN1 OUT2OUT1 J1 3 C T S LA SOMISIMOVE_SELECT LED EXT_IN1EXT_IN2EXT_OUT2EXT_OUT1 20191817161514131211 10987654321 SP K PPPPPPPPPP PPPPPPPXXD R 2 3.2/UCB0SOMI/UCB0SCL3.1/UCB0SIMO/UCB0SDA3.0/UCB0STE/UCA0CLK2.5/Rosc/CA52.4/CA1/TA22.3/CA0/TA12.2/CAOUT/TA0/CA42.1/TAINCLK/CA32.0/ACLK/CA21.7/TA2 1.6/TA11.5/TA01.4/SMCLK1.3/TA21.2/TA11.1/TA01.0/TACLKOUT/P2.7/CA7IN/P2.6/CA6VCC MSP430F2370U2 87654321 PROGRAMMING HEAJ5 470 R22 Q1MMBT3904 2 D E R P3.3/UCB0CLK/UCA0STE21P3.4/UCA0TXD/UCA-SIMO22P3.5/UCA0RXD/UCA0SOMI23P3.624P3.725P4.0/TB026P4.1/TB127P4.2/TB228P4.3/TB029P4.4/TB130 P4.5/TB231P4.6/TBOUTH/ACLK32P4.7/TBCLK33 RST/NMI38D/AVSST39TDAVCCDI40/OTTTC/TMCLDSKKI 33334567 LED MMBT3904Q2 BuzzerBZ1 SWVCC 1 DATA_CLKTOHOSTFROMHOST 47KANT_SEL_AANT_SEL_BR37ANT_SEL_C SPKR 0.01uFC25 UCVCC 47KR20 RESET GR TAG LEDD10 R29470 SchematiSimplifi DLP-RFID- 1 Not useMode Sel 21 TG 2.2uFC24 100R19 ced LP8C d 3V C C A B C D