8 7 6 5 4 3 2 1 REVISIONS ZONE REV. DESCRIPTION DATE APPROVED ALL A TABLE REDRAWN ECO 3290 12/10/86 DETAIL 1 B REMOVED UNUSED P/N# 02/10/09 C ADDED TS209N 03/04/11 D D ADDED TS-425 09/13/12 D 1.000 DETAIL A SCALE 2 : 1 .180 .100±.010 A .291 +.015 .115 -.000 DETAIL 2 .210 C C 1.000 A .500 .281 .093 1.000 2 PL. 2.000 .291 A B DETAIL 3 B 1.000 1.000 A .291 UNLESS OTHERWISE SPECIFIED: NAME DATE 11115 VANOWEN ST., NORTH HOLLYWOOD, DIMENSIONS ARE IN INCHES DRAWN TRUSHAR 02/06/09 CA 91605 A TOLERANCES: A FRACTIONAL CHECKED T-STRUT 5. DEGREASE ANGULAR: 1 4. STRAIGHT WITHIN .015/10" IN LENGTH TWO PLACE DECIMAL .03 ENG APPR. W/O INSERTS THREE PLACE DECIMAL .010 MFG APPR. 3. CUT ENDS TO BE SQUARE WITHIN .0025/INCH IN WIDTH PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC 2. REMOVE ALL BURRS THE INFORMATION CONTAINED IN THIS TOLERANCING PER: Q.A. SIZE DWG. NO. REV DRAWING IS THE SOLE PROPERTY OF 1. MAT'L: AL. EXTRUSION, 6063-T6, PRE-ANOD., P/N TS100 VECTOR ELECTRONICS & TECH., INC. ANY MATERIAL 1 THIRD ANGLE PROJECTION B 5280006 D REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF FINISH NOTES: UNLESS OTHERWISE SPECIFIED. VECTOR ELECTRONICS & TECH., INC. IS SCALE: 1:1 WEIGHT: SHEET 1 OF 1 PROHIBITED. DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1

8 7 6 5 4 3 2 1 REVISIONS ZONE REV. DESCRIPTION DATE APPROVED ALL RELEASED FOR PROTOTYPE - 100 UNITS OF CCK13S 02/14/80 50 CCM14S & 50 CCK13S P/N TS81-5 NO. OF HOLES WAS 30 A1 ACTUAL STOCK PARTS HAVE 31 07/31/80 P/N TS81-5 "B" DIM. WAS 7.500 D B NO. OF HOLES WERE 31/ ECO2013 03/26/81 D MOVED 1.000 DIM. LOCATION C CALLOUT FOR CLARITY NO ECO D ADDED TS81-6 &-7 D INC ECO 2628 12/17/84 A E INC ECO 3924 REMOVED P/N# TS81-6, -7 F 02/10/09 TS169-5,TS209-5 B .002 C G ADDED P/N TS169-5/90 02/13/13 .500±.015 .250 TYP. .250±.002 TYP. .156 .060 +.030/-.000 4 6 E 7 C 1.000±.015 C .291±.008 REF. 1.000±.060 TYP. DETAIL E SCALE 2 : 1 +.015 B .115 B -.000 .180 .100±.010 .210 UNLESS OTHERWISE SPECIFIED: NAME DATE 11115 VANOWEN ST., NORTH HOLLYWOOD, 7. TOOLING MARK MAY APPEAR DIMENSIONS ARE IN INCHES DRAWN TRUSHAR 02/10/09 CA 91605 A 6. USE .1565 DIA. PUNCH TO FORM RADIUS EQUAL WITHIN .005 FROM CL OF SLOT TOLERANCES: A 5. PART TO BE FREE OF BURRS AND SURFACE SCRATCHES FARNAGCUTLIAORN: AL.X CHECKED T-STRUT 4. NON CUMULATIVE TOLERANCE TWO PLACE DECIMAL .03 ENG APPR. FOR SNAP-IN CARD GUIDE THREE PLACE DECIMAL .005 MFG APPR. 3. PART TO BE STRAIGHT WITHIN .015/10 INCHES IN LENGTH PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC 2. CUT ENDS TO BE SQUARE WITHIN .0025/INCH IN WIDTH THE INFORMATION CONTAINED IN THIS TOLERANCING PER: Q.A. SIZE DWG. NO. REV DRAWING IS THE SOLE PROPERTY OF 1. MAT'L: AL. EXTRUSION, 6063-T6, PRE-ANOD., P/N TS100 VECTOR ELECTRONICS & TECH., INC. ANY MATERIAL 1 THIRD ANGLE PROJECTION B M6336D4.2 G REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF FINISH NOTES: UNLESS OTHERWISE SPECIFIED. VECTOR ELECTRONICS & TECH., INC. IS SCALE: 1:1 WEIGHT: SHEET 1 OF 1 PROHIBITED. DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1