TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection - SP4060 Series SP4060 Series 2.5V 20A Diode Array RoHS Pb GREEN Description The SP4060 integrates low capacitance diodes with an additional zener diode to protect each I/O pin against ESD and high surge events. This robust device can safely absorb up to 20A per IEC 61000-4-5 (t =8/20µs) without p performance degradation and a minimum ±30kV ESD per IEC 61000-4-2 International Standard. Their low loading capacitance also makes them ideal for protecting high speed signal pins. Features • ESD, IEC 61000-4-2, • Low capacitance of 4.4pF ±30kV contact, ±30kV air (TYP) per I/O Pinout • EFT, IEC 61000-4-4, 40A • Low leakage current of (5/50ns) 1µA (MAX) at 2.5V • Lightning, IEC 61000-4-5, • Moisture Sensitivity Level I/O 1 I/O 8 20A (8/20µs) (MSL-1) I/O 2 I/O 7 I/O 6 I/O 3 Applications I/O 5 I/O 4 NC GND • LCD/PD TVs • Set Top Boxes • Desktops • Notebooks • Game Consoles Functional Block Diagram I/O 8 I/O 7 I/O 6 I/O 5 Application Example LVDS Interface LVDS Controller CLK+ CLK- A0+ A0- Outside World A1+ I/O 1 I/O 2 I/O 3 I/O 4 GND A1- A2+ A2- Additional Information Signal Shield GND Datasheet Resources Samples SP4060-08ATG Shield GND Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17

TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection - SP4060 Series Absolute Maximum Ratings Thermal Information Symbol Parameter Value Units Parameter Rating Units I Peak Current (t=8/20μs) 20.0 A Storage Temperature Range –55 to 150 °C PP p Maximum Junction Temperature 150 °C P Peak Pulse Power (t=8/20µs) 300 W PK p Maximum Lead Temperature 260 °C T Operating Temperature –40 to 125 ºC OP (Soldering 20-40s) T Storage Temperature –55 to 150 °C STOR CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (T =25ºC) OP Parameter Symbol Test Conditions Min Typ Max Units Reverse Standoff Voltage V 2.5 V RWM Snap Back Voltage V I =50mA 2.0 V SB SB Reverse Leakage Current I V =2.5V, I/O to GND 0.5 1.0 µA LEAK R I =1A, t=8/20µs, Fwd 4.5 5.5 V PP p I =5A, t=8/20µs, Fwd 6.0 7.2 V PP p Clamp Voltage1 V C I =10A, t=8/20µs, Fwd 8.0 9.6 V PP p I =20A, t=8/20µs, Fwd 12.5 15.0 V PP p IEC61000-4-2 (Contact) ±30 kV ESD Withstand Voltage1 V ESD IEC61000-4-2 (Air) ±30 kV Diode Capacitance1 C Reverse Bias=0V 4.4 5.0 pF I/O-GND Diode Capacitance1 C Reverse Bias=0V 2.2 pF I/O-I/O Note: 1. Parameter is guaranteed by design and/or device characterization. 8/20µs Pulse Waveform Clamping Voltage vs. I PP 110% 14.0 100% 12.0 90% 80% V)C 10.0 of IPP 70% age ( 8.0 nt 60% olt e V Perc 4500%% amp 6.0 Cl 4.0 30% 20% 2.0 10% 0.0 0% 1.0 3.0 5.0 7.0 9.0 11.0 13.0 15.0 17.0 19.0 21.0 0.0 5.0 10.0 15.0 20.0 25.0 30.0 Time (μs) Peak Pulse Current-IPP (A) © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17

TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection - SP4060 Series Capacitance vs. Bias Insertion Loss (S21) I/O to GND 5.0 5 0 4.0 -5 F) B) e (p3.0 n (d-10 Capacitanc2.0 Attenuatio--2105 1.0 -25 0.0 -30 0.0 0.5 1.0 1.5 2.0 2.5 10 100 1000 10000 DC Bias (V) Frequency (MHz) Soldering Parameters Reflow Condition Pb – Free assembly tP TP CCrriittiiccaall ZZoonnee - Temperature Min (Ts(min)) 150°C e RRaammpp--uupp TTLL ttoo TTPP Pre Heat -- TTeimmep e(mraitnu rteo Mmaaxx )( T(ts()max)) 2600 0–° C180 secs rutare TS(mTaxL) tL s pm RRaammpp--ddoown Average ramp up rate (Liquidus) Temp e PPrreehheeaatt 3°C/second max T (TL) to peak TS(min) tS T to T - Ramp-up Rate 3°C/second max S(max) L Reflow -- TTeemmppeerraattuurree ((TtL)) (Liquidus) 26107 –° C1 50 seconds 25 time to peak temperature Time L Peak Temperature (T ) 260+0/-5 °C P Time within 5°C of actual peak 20 – 40 seconds Temperature (t ) p Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T ) 8 minutes Max. P Do not exceed 260°C Package Dimensions — MSOP10 2.00 D [0.0787] 0.50 Package MSOP 10 [0.0197] Pins 10 JEDEC MO-187 Millimeters Inches E1 E 5.28[0.2079]3.20[0.1260] 1.04[0.0409]4.24[0.1669] DAAIM1 0M.0-in0 M01..11a05x 0M.0-i0n0 00M..00a40x36 B 0.17 0.27 0.007 0.011 [00.0.13226] c 0.08 0.23 0.003 0.009 Solder Pad Layout D 2.90 3.10 0.114 0.122 1 2 E 4.67 5.10 0.184 0.200 A E1 2.90 3.10 0.114 0.122 C e 0.50 BSC 0.020 BSC L 0.40 0.80 0.016 0.032 B e A1 L © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17

TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection - SP4060 Series Part Numbering System Product Characteristics SP 4060 -08ATG Lead Plating Pre-Plated Frame G= Green TVS Diode Arrays Lead Material Copper Alloy (SPA® Diodes) T= Tape & Reel Lead Coplanarity 0.0004 inches (0.102mm) Package Series A = MSOP10 Substitute Material Silicon Number of Channels Body Material Molded Epoxy Flammability UL 94 V-0 Part Marking System Notes : 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. LF 4. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI 11-13. YYWWD YYWW = Date code Product Series P*8 Number of P = SP4060 Channels Assembly Site Ordering Information Part Number Package Marking Min. Order Qty. SP4060-08ATG MSOP10 P*8 4000 Embossed Carrier Tape & Reel Specification — MSOP-10 Millimetres Inches Min Max Min Max E 1.65 1.85 0.065 0.073 F 5.40 5.60 0.213 0.220 D 1.50 1.60 0.059 0.063 D1 1.50 Min 0.059 Min P0 3.90 4.10 0.154 0.161 10P0 40.0± 0.20 1.574±0.008 W 11.90 12.10 0.469 0.476 P 7.90 8.10 0.311 0.319 A0 5.20 5.40 0.205 0.213 B0 3.20 3.40 0.126 0.134 K0 1.20 1.40 0.047 0.055 t 0.30 ± 0.05 0.012± 0.002 Pin 1 Location User Feeding Direction Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17