NMG Series www.murata-ps.com Isolated 2W Single Output DC/DC Converters SELECTION GUIDE Order Code Nominal Input Voltage Output Voltage Output Current Input Current at Rated Load Load Regulation (Typ) Load Regulation (Max) Ripple & Noise (Typ)1 Ripple & Noise (Max)1 Efficiency (Min.) Efficiency (Typ.) Isolation Capacitance MTTF2 V V mA mA % mVp-p % % pF kHrs NMG0505SC 5 5 400 470 5.7 7.3 28 35 81 83 33 3956 NMG0509SC 5 9 222 455 4.2 5.9 20 25 84 86.5 40 3682 NMG0512SC 5 12 167 450 3.8 5.1 18 25 84 87.5 40 3299 FEATURES NMG0515SC 5 15 133 450 3.4 4.5 16 25 84 87.5 40 2833 NMG0524SC 5 24 83 465 4.3 6 35 60 82 85 35 2189 (cid:132)(cid:3)UL 60950 recognised NMG1205SC 12 5 400 200 4.2 4.9 22 35 81 83.5 40 2519 (cid:132)(cid:3)Efficiency from 80% NMG1209SC 12 9 222 190 2.6 3.1 16 25 83 87 61 2405 (cid:132)(cid:3)Wide temperature performance at full NMG1212SC 12 12 167 190 2.4 2.9 13 25 85 88 74 2235 2 Watt load, –40°C to 85°C NMG1215SC 12 15 133 185 2.0 2.4 12 25 85 88 68 2011 NMG1224SC 12 24 83 190 2.6 4 25 40 84 86.5 60 2189 (cid:132)(cid:3)Industry standard pinout NMG1505SC 15 5 400 160 4.3 6 40 60 80 83 40 3963 (cid:132)(cid:3)1kVDC isolation ‘Hi Pot Test’ NMG1509SC 15 9 222 155 2.9 4.5 25 40 82 86.5 55 3176 NMG1512SC 15 12 167 150 2.4 3.5 25 40 84 87.5 65 2875 (cid:132)(cid:3)5V, 12V, 15V & 24V input NMG1515SC 15 15 133 150 2.3 3.5 25 40 84 88 75 2483 (cid:132)(cid:3)5V, 9V, 12V, & 15V output NMG2405SC 24 5 400 100 4.1 6 40 70 80 84 45 3659 NMG2409SC 24 9 222 95 2.6 4 30 50 84 87.5 55 2496 (cid:132)(cid:3)Internal SMD construction NMG2412SC 24 12 167 95 2.1 3.5 25 50 84 88 75 3824 (cid:132)(cid:3)No external components required NMG2415SC 24 15 133 95 2 3.5 30 50 85 88.5 85 3500 When operated with additional external load capacitance the rise time of the input voltage will determine the maximum external (cid:132)(cid:3)MTTF up to 3.9 million hours capacitance value for guaranteed start up. The slower the rise time of the input voltage the greater the maximum value of the additional external capacitance for reliable start up. (cid:132)(cid:3)Pin compatible with CMR, CRR1, NMR & MER1 series INPUT CHARACTERISTICS (cid:132)(cid:3)No electrolytic or tantalum capacitors Parameter Conditions Min. Typ. Max. Units Continuous operation, 5V input types 4.5 5 5.5 V Continuous operation, 12V input types 10.8 12 13.2 PRODUCT OVERVIEW Voltage range Continuous operation, 15V input types 13.5 15 16.5 The NMG series of DC/DC Converters is Continuous operation, 24V input types 21.6 24 26.4 particularly suited to isolating and/or converting Reflected ripple current 7.5 15 mA p-p DC power rails. The galvanic isolation allows the device to be configured to provide an isolated ABSOLUTE MAXIMUM RATINGS negative rail in systems where only positive rails Lead temperature 1.5mm from case for 10 seconds 260°C exist. The wide temperature range guarantees Input voltage VIN, NMG05 types 7V startup from –40°C and full 2 watt output at 85°C. Input voltage VIN, NMG12 types 15V Input voltage VIN, NMG15 types 18V Input voltage VIN, NMG24 types 28V OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Rated Power TA=-40°C to 85°C 2 W Voltage Set Point Accuracy See tolerance envelope Line regulation High VIN to low VIN 1.05 1.2 %/% 1. See Ripple & Noise characterisation method. 2. Calculated using MIL-HDBK-217F FN2 with nominal input voltage at full load. For full details go to www.murata-ps.com/rohs All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified. www.murata-ps.com/support KDC_NMG.E03 Page 1 of 7

NMG Series Isolated 2W Single Output DC/DC Converters ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Isolation test voltage Flash tested for 1 second 1000 VDC Resistance Viso= 1000VDC 10 GΩ GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units 24V output types 70 Switching frequency kHz All other types 60 TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Specification All output types -40 85 Storage -50 125 °C Case Temperature above 5V input types and 5V output types 30 ambient All other types 25 Cooling Free air convection EFFICIENCY VS LOAD 5V Input 12V Input 90 90 80 80 70 70 NMG0512SC 60 NMG0505SC 60 NMG1205SC Efficiency (%) 4500 NNNMMMGGG000555012954SSSCCC Efficiency (%) 4500 NNNNMMMMGGGG1111222201129254SSSSCCCC 30 30 20 20 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100 Load (%) Load (%) 15V Input 24V Input 90 90 80 80 70 70 NMG2405SC 60 NMG1505SC 60 NMG2409SC Efficiency (%) 4500 NNNMMMGGG111555011925SSSCCC Efficiency (%) 4500 NNMMGG22441125SSCC 30 30 20 20 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100 Load (%) Load (%) www.murata-ps.com/support KDC_NMG.E03 Page 2 of 7

NMG Series Isolated 2W Single Output DC/DC Converters TEMPERATURE DERATING GRAPH 3 W) 2 85°C er ( w o P ut 1 Safe Operating Area p ut O 0 -40 0 50 100 150 Ambient Temperature (°C) TECHNICAL NOTES ISOLATION VOLTAGE ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions NMG series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 minute. A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?” The NMG series has been recognized by Underwriters Laboratory for functional insulation. Both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materi- als, construction and environment. The NMG series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly lim- ited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. SAFETY APPROVAL The NMG series has been recognised by Underwriters Laboratory (UL) to UL 60950 for functional insulation in a maximum ambient temperature of 85ºC and/or case temperature limit of 130ºC. Case temperature measured on the face opposite the pins. File number E151252 applies. The NMG Series of converters are not internally fused so to meet the requirements of UL 60950 an input line fuse should always be used. An anti-surge 2A should be used for NMG05xxSC models, and an anti-surge 0.75A should be used for NMG12xxSC models. All fuses should be UL approved and rated to at least the maximum allowable DC input voltage. RoHS COMPLIANCE INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 260°C for 10 seconds. The pin termination finish is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. This series are backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs www.murata-ps.com/support KDC_NMG.E03 Page 3 of 7

NMG Series Isolated 2W Single Output DC/DC Converters APPLICATION NOTES Minimum load The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%. Capacitive loading and start up Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF. Start-up time Start-up time Typical Start-Up Wave Form μs μs NMG0505SC 444 NMG1505SC 100 NMG0509SC 1120 NMG1509SC 170 NMG0512SC 1930 NMG1512SC 300 NMG0515SC 3470 NMG1515SC 450 NMG1205SC 409 NMG2405SC 80 NMG1209SC 1320 NMG2409SC 130 NMG1212SC 1320 NMG2412SC 220 NMG1215SC 2270 NMG2415SC 330 NMG0524SC 2200 NMG1224SC 1400 Ripple & Noise Characterisation Method All measurement to be taken with the following components connected to the UUT as detailed below. 50 Ohm coax cable, solder connections one end, BNC plug at the other end. C1 1μF X7R multilayer ceramic capacitor rated at minimum 3 x the output voltage of the UUT 10μF tantalum capacitor rated at minimum 1.5 x the output voltage of the UUT with ESR of less than 100 milliohms at 100 kHz e.g. AVX TPS C2 series. C3 100nF multilayer ceramic capacitor, general purpose R1 450 Ohm resistor, carbon film, ±1% R2 50 Ohm BNC termination T1 3T of the coax cable through a ferrite toroid eg Ferroxcube TN32/19/13-3E25 RLOAD Resistive load at the UUT maximum rating. Connections via twisted wires. Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic DC/DC Converter OSCILLOSCOPE C1 C2 C3 R1 T1 R2 + + Y INPUT SUPPLY Input Output - - R LOAD www.murata-ps.com/support KDC_NMG.E03 Page 4 of 7

NMG Series Isolated 2W Single Output DC/DC Converters APPLICATION NOTES (continued) Output Ripple Reduction By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max. Component selection Capacitor: It is required that the ESR (Equivalent Series Resistance) should be as low as possible, ceramic types are recommended. The voltage rating should be at least twice (except for 15V output), the rated output voltage of the DC/DC converter. Inductor: The rated current of the inductor should not be less than that of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF (Self Resonant Frequency) should be >20MHz. L DC Power C Load Source DC Inductor Capacitor L, μH SMD Through Hole C, μF NMG0505SC 4.7 82472C 11R472C 10 NMG0509SC 10 82103C 11R103C 4.7 NMG0512SC 22 82223C 11R223C 2.2 NMG0515SC 47 82473C 11R473C 1 NMG0524SC 47 82473C 11R473C 1 NMG1205SC 4.7 82472C 11R472C 10 NMG1209SC 10 82103C 11R103C 4.7 NMG1212SC 22 82223C 11R223C 2.2 NMG1215SC 47 82473C 11R473C 1 NMG1224SC 47 82473C 11R473C 1 NMG1505SC 4.7 82472C 11R472C 10 NMG1509SC 10 82103C 11R103C 4.7 NMG1512SC 22 82223C 11R223C 2.2 NMG1515SC 47 82473C 11R473C 1 NMG2405SC 4.7 82472C 11R472C 10 NMG2409SC 10 82103C 11R103C 4.7 NMG2412SC 22 82223C 11R223C 2.2 NMG2415SC 47 82473C 11R473C 1 www.murata-ps.com/support KDC_NMG.E03 Page 5 of 7

NMG Series Isolated 2W Single Output DC/DC Converters TOLERANCE ENVELOPES The voltage tolerance envelopes show typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to changes in output loading and set point accuracy. 1224, 1515, 2412, 2415 2405 +6% +3% +2% e e g g a a olt olt +2% ut V 0% ut V p p ut ut 0% O O -3% -3% 10 25 50 75 100 10 25 50 75 100 Output Load Current (%) Output Load Current (%) 05XX,, 1205, 1209, 1212, 1215, 1505, 1509, 1512, 2409 +5% e g a olt +2% V ut p ut 0% O -4% 10 25 50 75 100 Output Load Current (%) www.murata-ps.com/support KDC_NMG.E03 Page 6 of 7

NMG Series Isolated 2W Single Output DC/DC Converters PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS PIN CONNECTIONS - 4 PIN SIP Pin Function 19.65 [0.774] MAX 1 +VIN 2 -VIN 7.65 [0.301] MAX 4 -VOUT MIN 6 +VOUT 10.15 [0.400] MAX XNYMYWGW0505SC 0.40 [0.0016] TUBE OUTLINE DIMENSIONS 9.3 [0.366] 1 2 4 6 4.10±0.50 [0.161±0.020] 2.54 [0.100] 0.50±0.05 [0.020±0.002] 5.08 [0.200] 12.43 [0.489] 18.0 [0.709] 0.25±0.05 [0.010±0.002] 1.45 ] 0.057] 1.00 0.039 12.70 [0.500] 2.52 ] 0.099] 1.54 0.061 5.0 [0.197] Unless otherwise stated all dimensions in mm (inches) Controlling dimension is mm. Unless otherwise specified all dimensions in mm [inches] ±0.55mm [0.022]. All pins on a 2.54mm (0.100”) pitch and within 0.25mm (0.010”) of true position. Weight: 2.8g Tube Length : 520mm [20.472] ±2.0 [0.079]. Tube Quantity : 25 RECOMMENDED FOOTPRINT DETAILS 1.15 ] 0.045] X 4 HOLES Ø Ø 1.00 0.039 2.54 [0.100] 2.54 [0.100] This product is subject to the following operating requirements Murata Power Solutions, Inc. and the Life and Safety Critical Application Sales Policy: 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Refer to: http://www.murata-ps.com/requirements/ ISO 9001 and 14001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2017 Murata Power Solutions, Inc. www.murata-ps.com/support KDC_NMG.E03 Page 7 of 7

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M urata: NMG1215SC NMG0512SC NMG0509SC NMG1209SC NMG0515SC NMG1212SC NMG1205SC NMG0505SC NMG2412SC NMG1509SC NMG1512SC NMG1505SC NMG2409SC NMG2415SC NMG2405SC NMG1515SC