E M C C o m p o n e n t s May 2018 Chip beads For power line MPZ series MPZ2012 type MPZ2012 2012[0805 inch]* * Dimensions code JIS[EIA]

(2/10) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip- ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip- ment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual- ity require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (8) Public information-processing equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment　　 (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro- tection circuit/device or providing backup circuits in your equipment. 20180521 / beads_commercial_power_mpz2012_en.fm

(3/10) E M C C o m p o n e n t s Chip beads Product compatible with RoHS directive Halogen-free For power line Compatible with lead-free solders Overview of MPZ2012 type FEATURES Noise reduction solution for power line. Compared to the MMZ series, has low direct current resistance for compatibility with large currents, optimal for low power consumption. Performs well even in signal lines where low direct current resistance is required. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MPZ 2012 S 300 A T 000 L×W×T dimensions Impedance Characteristic Series name Material name Packaging style Internal code (mm) () at 100MHz type 2012 2.0×1.25x0.85 S 300 30 A T Taping 000 221 220 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature ranges Package quantity Individual weight Type Operating Storage temperature temperature （°C） （°C） (pieces/reel) （mg） MPZ2012 –55 to +125 –55 to +125 4,000 8 The storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

(4/10) E M C C o m p o n e n t s MPZ2012 type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T4 e ur T3 T3 at er p m e T T2 T: t3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

(5/10) E M C C o m p o n e n t s MPZ2012 type MATERIAL CHARACTERISTIC S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS　 2500 2000 1500 1000 S 500 0 10 100 1000 Frequency(MHz) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

(6/10) E M C C o m p o n e n t s MPZ2012 type SHAPE & DIMENSIONS 2.0±0.2 2 0. ± 5 2 1. 2 0. ± 5 8 0. 0.5±0.3 Dimensions in mm RECOMMENDED LAND PATTERN 2 1. 0.8 1 0.8 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

(7/10) E M C C o m p o n e n t s MPZ2012 type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance DC resistance Rated current Part No. [100MHz] () Tolerance ()max. (A)max. 30 ±10 0.010 6 MPZ2012S300AT000 100 ±25% 0.020 4 MPZ2012S101AT000 220 ±25% 0.040 3 MPZ2012S221AT000 330 ±25% 0.050 2.5 MPZ2012S331AT000 600 ±25% 0.100 2 MPZ2012S601AT000 1000 ±25% 0.150 1.5 MPZ2012S102AT000  Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85°C or more in temperature of the product. ○Measurement equipment Measurement item Product No. Manufacturer Impedance E4991A+16192A Keysight Technologies DC resistance Type-7556 Yokogawa ＊ Equivalent measurement equipment may be used. ○ Rated current vs. temperature characteristics (derating) 7 S300A 6 )A5 (ent 4 S101A d curr3 SS323211AA e at S601A R2 S102A 1 0 –55 –35 –15 5 25 45 65 85 105 125 Temperature (°C) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

(8/10) E M C C o m p o n e n t s MPZ2012 type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MPZ2012S series 1200 1100 MPZ2012S221A 1000 MPZ2012S102A MPZ2012S101A 900 MPZ2012S300A MPZ2012S601A 800 Ω) MPZ2012S331A (e 700 c an 600 d pe 500 m I 400 300 200 100 0 1 10 100 1000 10000 Frequency (MHz) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

(9/10) E M C C o m p o n e n t s MPZ2012 type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MPZ2012S300AT000 MPZ2012S101AT000 MPZ2012S221AT000 50 140 300 Ω()nce 4300 ZR Ω()nce 11802000 Z R Ω()nce 122505000 Z da20 da 60 da R e e e100 p p 40 p Im10 X Im 20 X Im 50 X 0 0 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 Frequency (MHz) Frequency (MHz) Frequency (MHz) MPZ2012S331AT000 MPZ2012S601AT000 MPZ2012S102AT000 400 700 1200 350 600 1000 Ω()ce 320500 Z R Ω()ce 450000 Z Ω()ce 800 Z R edan 210500 edan 300 R edan 460000 mp 100 mp 200 mp I 50 X I 100 X I 200 X 0 0 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 Frequency (MHz) Frequency (MHz) Frequency (MHz) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

(10/10) E M C C o m p o n e n t s MPZ2012 type PACKAGING STYLE REEL DIMENSIONS 2.0±0.5 n. mi 0 6 ø 1.0 ø13±0.2 8.4+–02..00 ø21±0.8 14.4max. ø180±2.0 Dimensions in mm TAPE DIMENSIONS 1 0. 1.5+00.1 2.0±0.05 4.0±0.1 75± 1. 5 0 ±0. 0.3 5 ± B 3. 8.0 A P1 K Dimensions in mm Type A B P1 K MPZ2012 1.5±0.2 2.3±0.2 4.0±0.1 1.1max. 160min. Taping 200min. Drawing direction 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz2012_en.fm

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T DK: MPZ2012S331A MPZ2012S601A MPZ2012S101A MPZ2012S300A MPZ2012S221A MPZ2012S102A MPZ2012S101ATD25 MPZ2012S300ATD25 MPZ2012S102ATD25 MPZ2012S601ATD25 MPZ2012S221ATD25 MPZ2012S331ATD25