H-1802 S C E T A H W-IPL IP series C S T I W S L E N A Pushbutton switches for harsh environments • P bushing Ø 12 mm • latching DISTINCTIVE FEATURES Latching action Illuminated or non-illuminated Compact Flat round actuator for optional marking Sealed to IP67 ENVIRONMENTAL SPECIFICATIONS • Front panel sealing : IP67 according to IEC 60529 • Shock resistance : 100 g according to IEC 512-4, test 6c • Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d • Salt spray : IEC 512-6, test 11f • Robustness (non-illuminated) : IK06 according to EN 62262 (1 joule) • Operating temperature : -40 °C to +85 °C (-40 °F to +185 °F) ELECTRICAL SPECIFICATIONS • Max. current/voltage rating with resistive load: 4 A 12 VDC, 200,000 cycles 1 A 48 VDC, 200,000 cycles For W terminals, current has 2 A 48 VDC, 100,000 cycles to be limited to 400 mA. 3 A 48 VDC, 75,000 cycles 1 A 72 VDC, 15,000 cycles • Initial contact resistance : 100 mΩ max. • Insulation resistance : 1 GΩ min. at 500 VDC • Dielectric strength : 1,500 Vrms between terminals 1,000 Vrms between terminals and frame LED COMPONENT SPECIFICATIONS LED color Forward current Typ. forward voltage Max. forward voltage Super red (L0S) 20 mA 1.95 V 1.95 V A resistor must be series-connected by the user. Yellow (L0Y) 20 mA 2 V 2.05 V Resistor value = supply voltage - LED forward voltage Green (L0G) 20 mA 2.1 V 2.5 V LED forward current Blue (L0B) 20 mA 3.2 V 4 V The company reserves the right to change specifications without notice. 1

S E H IP series C T I W S Pushbutton switches for harsh environments • L E bushing Ø 12 mm • latching N A P GENERAL SPECIFICATIONS TERMINALS •• TP5.oa5tn amel lmt rtha (vic.2ek1ln :7 e2) s.m5s ma: 1xm..5 (m.0m98 (). 0±5 09.)3 mmimn. 2.40(.094) 8.40(.330) 2.30(.090) 1.40 • Typical operating force : 10 N (.10.3090) 3.40(.133) ((.21.10..18240007)) ((..210.158050)) 3.20(.125) • Low level/mech. life : 200.000 cycles • Torque : 1.5 Nm max. applied to nut Straight P Quick-connect Z1 Solder lug S • Soldering : 320 °C (608 °F) max. for 3 sec. CISCOSP ECH: 0.9 5-05-0E3 LECTRICAL FUNCTION CIPNLF1COS CISCOSZ-A MATERIALS DESSIN ECH 0.9 DESSIN ECH 0.9 5-05-03 17.10.01 • Case : thermoplastic, UL 94-V0 • Actuator : polyamide 6/6 • Bushing/bezel : zinc die-cast (zamak), black painted • Contacts : silver, gold plated OFF ON • Output wires (flying lead terminals) : F version : AWG20, section 0.6 mm2 W version : AWG24, section 0.23 mm2 • LED wires : MOUNTING F version : AWG26, section 0.12 mm2 W version : AWG24, section 0.23 mm2 • Lens : polycarbonate PANEL CUT-OUT Maxmax) • Terminal seal : epoxy (1.25.0970) min-5.50min-.216 AmPeEtaMl cporomdpuocntse nmtsa.y be recycled at end-of-life for the re-claiming of valuable 1 1.50(.059 Ø13.60 (.535DIA) ø13.50 (.531DIA) - Flat seal AGENCY APPROVAL 2 A 125 VAC/250 VAC File E83438 MATRIX MOUNTING - BACK OF PANEL SPACE REQUIREMENT See following pages. CIPDTF1EP 20.00 20.00 (.787) (.787) ECH1 CIPDTF1SFCT 20.00(.787) 18.10.0119.10(.751) 22.10.01 DESSIN ECH 0.9 CIPDTF1EA 2 DESSIN ECH 1 17.10.01

S E IP series H C T I W Pushbutton switches for harsh environments • S L bushing Ø 12 mm • latching E N A P BUILD YOUR PART NUMBER BASIC PART NUMBER IP SERIES ACTUATOR SHAPES ELECTRICAL FUNCTION TERMINALS CONTACTS C Square 1 OFF - ON S Solder lugs Silver, gold AD plated R Round, curved F Flying leads, standard P Round, flat W Flying leads, thin Z1 Quick-connect Actuator marking P Straight PC available on round flat models (symbol 10 mm max.). On request. OPTIONS ACTUATOR COLORS LED COLORS OPTIONS APPROVAL 1 Blue Blank Non-illuminated. 100 Satin chrome Consult factory for bezel UL detail of approved B Dark blue L0S Super red models. Bright chrome 101 bezel (round only) 2 Black L0Y Yellow High actuator 3 Green L0G Green 104 (non-illum. round models only) 4 Grey L0B Blue 5 Yellow 6 Red 7/1 White 8 Bright chrome 9 Orange A Satin chrome ABOUT THIS SERIES On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart. Notice : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand (P/N U5125). See "Sealing Boots" section of website. Mounting accessories : Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-Ring. 3

S E H IP series C T I W S Pushbutton switches for harsh environments • L E bushing Ø 12 mm • latching N A P FLAT All drawings with standard flying lead terminals. ILLUMINATED - SQUARE MODELS 7.00 (.275) (. 47122S.0Q0) Min Min) 5.70 (.224) 17.50 Solder lug terminals 1.50 (.059 (.688SQ) IPC1SAD OFF - ON 8.20 (.322) ø12.00x0.75SI Flying leadIP tCer1mFAinDals OFF - ON 12.40 (.488) EP(O.4X7Y2D IAx0.75IS) 16.00 Max (.629 Max) For THIN flying leads, replace F with W. 500±10(19.68±.393) Also available with straight PC : IPC1PAD or quick-connect terminals : IPC1Z1AD. Wire colors : black : contact, red : LED anode(+), blue : LED cathode(-) FLAT ILLUMINATED - ROUND MODELS Solder lug terminals 7.00 (.275) (.4ø7122D.0IA0 ) E1.50 Min C(.059 Min) CIPHD0.T9F 1CL5.70 U(.224) (.6ø8187D.5I0A ) IPR1SAD OFF - ON 8.20 (.322) ø12.010x07.75S.I 10.01 Flying leadIP tRer1mFAinDals OFF - ON 12.40 (.488) EP(O.4X7Y2D IAx0.75IS) 16.00 Max (.629 Max) FAolsro T aHvIaNil aflbylien gw ilteha sdtsra, irgehptl aPcCe : FIP wRi1thP AWD. or quick-connect terminals : IPR1Z1AD. 500±10(19.68±.393) Wire colors : black : contact, red : LED anode(+), blue : LED cathode(-) FLAT NON-ILLLUMINATED - SQUARE MODELS Solder lug terminals 7.00 (.275) (.47122S.0Q0) C1.50 Min I(.059 Min) PDTF1RLU5.70 (.224) (.68187S.5Q0) IPC1SAD OFF - ON 8.20 (.322) øD12.0E0x0S.75SSI IN ECH 0.9 Flying leadIP tCer1mFAinDals OFF - ON 12.40 (.488) EPO(.X41Y72 D7IAx0..715IS0) .01 16.00 Max (.629 Max) 500±10(19.68±.393) For THIN flying leads, replace F with W. Also available with straight PC : IPR1PAD or quick-connect terminals : IPC1Z1AD. FLAT NON-ILLUMINATED - ROUND MODELS Ø17.50 (.688DIA) CURVED ACTUATOR 7.00(.275) (.4Ø7122D.0IA0) 2.00(.078) MinMin) (.4Ø7122D.0IA0) 2.00(.078) 7.00(.275) Solder lug terminals IPR1SAD OFF - ON 1.50 (.059 Flying lead terminals IPR1FAD OFF - ON CIPDTF1CNL FLAT ACTUATOR 8.20(.322) Ø12.00x0.7D5SIESSIN ECH 0.9 (.472DIAx0.75IS) FSlyoilndge rl eluagd tteerrmmiinnaallss IIPPPP11SFAADD OOFFFF -- OONN 12.40(.488) EPOXY 17.10.0114.10(.555) For THIN flying leads, replace F with W. 500±10(19.68±.393) Also available with straight PC: IP•1PAD or quick-connect terminals: IP•1Z1AD 4

S E IP series H C T I W S Pushbutton switches for harsh environments • L bushing Ø 12 mm • latching E N A P ACTUATOR COLORS BASIC P/N 1 Blue 6 Red B Dark blue 7/1 White 2 Black 8 Bright chrome 3 Green 9 Orange 4 Grey A Satin chrome 5 Yellow LED COLORS BASIC P/N Blank Non-illuminated L0S Super red L0Y Yellow L0G Green L0B Blue OPTIONS BASIC P/N 110001 SBaritginh tc chhrorommee b beezzeell (round only) (.Ø47122D.0IA0) 4.70(.185) (.Ø47122D.0IA0) 4.70(.185) 104 High actuator - For round, non-illuminated only 104 IPR 104 IPP AGENCY APPROVAL BASIC P/N UL Consult factory for details of approved models. To order switches marked UL, complete above box with ”UL”. 5