HCPL-4562, HCNW4562 High Bandwidth, Analog/Video Optocouplers Data Sheet Description Features The HCPL-4562 and HCNW4562 optocouplers provide • Wide bandwidth[1]: wide bandwidth isolation for analog signals. They are ideal 17 MHz (HCPL-4562) for video isolation when combined with their application 9 MHz (HCNW4562) circuit (Figure 4). High linearity and low phase shift are • High voltage gain[1]: achieved through an AlGaAs LED combined with a high 2.0 (HCPL-4562) speed detector. These single channel optocouplers are 3.0 (HCNW4562) available in 8-Pin DIP and Widebody package • Low G temperature coefficient: -0.3%/°C configurations. V • Highly linear at low drive currents Functional Diagram • High-speed AlGaAs emitter • Safety approval: UL Recognized NC 1 8 VCC – 3750 V rms for 1 minute (5000 V rms for 1 minute for HCPL-4562#020 and HCNW4562) per UL 1577 ANODE 2 7 VB CSA Approved CATHODE 3 6 VO IEC/EN/DIN EN 60747-5-2 Approved – V = 1414 V for HCNW4562 IORM peak NC 4 5 GND • Available in 8-pin DIP and widebody packages Applications • Video isolation for the following standards/formats: NTSC, PAL, SECAM, S-VHS, ANALOG RGB • Low drive current feedback element in switching HCPL-4562 Functional Diagram power supplies, e.g., for ISDN networks • A/D converter signal isolation • Analog signal ground isolation • High voltage insulation CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

Selection Guide Single Channel Packages 8-Pin DIP Widebody (300 Mil) (400 Mil) HCPL-4562 HCNW4562 Ordering Information HCPL-4562 is UL Recognized with 3750 Vrms for 1 minute per UL1577 unless otherwise specified. HCNW4562 is UL Recognized with 5000 Vrms for 1 minute per UL1577. Option Part RoHS non RoHS Surface Gull Tape UL 5000 Vrms/ IEC/EN/DIN Number Compliant Compliant Package Mount Wing & Reel 1 Minute rating EN 60747-5-2 Quantity -000E no option 300 mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel HCPL-4562 -020E #020 X 50 per tube -320E #320 X X X 50 per tube -520E #520 X X X X 1000 per reel -060E #060 X[1] 50 per tube -000E no option 400 mil X X[2] 42 per tube HCNW4562 -300E #300 Widebody X X X X[2] 42 per tube -500E #500 DIP-8 X X X X X[2] 750 per reel Notes: 1. IEC/EN/DIN EN 60747-5-2 V = 630 V Safety Approval. IORM peak 2. IEC/EN/DIN EN 60747-5-2 V = 1414 V Safety Approval. IORM peak To order, choose a part number from the part number Schematic column and combine with the desired option from the I option column to form an order entry. CC 8 VCC 2 IF Example 1: ANODE + HCPL-4562-520E to order product of Gull Wing Surface V F IO 6 Mount package in Tape and Reel packaging with UL 5000 – VO CATHODE Vrms/1 minute rating and RoHS compliant. 3 Example 2: 5 GND HCNW4562 to order product of 8-Pin Widebody DIP IB 7 package in Tube packaging with IEC/EN/DIN EN 60747-5- VB 2 V = 1414 V Safety Approval and UL 5000 Vrms/1 IORM peak minute rating and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation ‘#XXX’ is used for existing products, HCPL-4562 Schematic while (new) products launched since July 15, 2001 and RoHS compliant will use ‘–XXXE.’ 2

Package Outline Drawings 8-Pin DIP Package (HCPL-4562) 9.65 ± 0.25 7.62 ± 0.25 (0.380 ± 0.010) (0.300 ± 0.010) TYPE NUMBER 8 7 6 5 OPTION CODE* 6.35 ± 0.25 (0.250 ± 0.010) A XXXXZ DATE CODE YYWWRU UL 1 2 3 4 RECOGNITION 1.78 (0.070) MAX. 1.19 (0.047) MAX. + 0.076 5° TYP. 0.254 - 0.051 + 0.003) 3.56 ± 0.13 4.70 (0.185) MAX. (0.010- 0.002) (0.140 ± 0.005) 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 0.65 (0.025) MAX. DIMENSIONS IN MILLIMETERS AND (INCHES). (0.043 ± 0.013) * MARKING CODE LETTER FOR OPTION NUMBERS 2.54 ± 0.25 "L" = OPTION 020 (0.100 ± 0.010) OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-4562) LAND PATTERN RECOMMENDATION 9.65 ± 0.25 1.016 (0.040) (0.380 ± 0.010) 8 7 6 5 6.350 ± 0.25 10.9 (0.430) (0.250 ± 0.010) 1 2 3 4 2.0 (0.080) 1.27 (0.050) 1.780 9.65 ± 0.25 (0.070) (0.380 ± 0.010) 1.19 MAX. (0.047) 7.62 ± 0.25 MAX. (0.300 ± 0.010) + 0.076 0.254 - 0.051 3.56 ± 0.13 + 0.003) (0.140 ± 0.005) (0.010- 0.002) 1.080 ± 0.320 (0.043 ± 0.013) 0.635 ± 0.25 (0.025 ± 0.010) 12° NOM. 2.54 0.635 ± 0.130 (0.100) (0.025 ± 0.005) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 3

8-Pin Widebody DIP Package (HCNW4562) 11.15 ± 0.15 11.00 MAX. (0.442 ± 0.006) (0.433) 9.00 ± 0.15 8 7 6 5 (0.354 ± 0.006) TYPE NUMBER A DATE CODE HCNWXXXX YYWW 1 2 3 4 10.16 (0.400) TYP. 1.55 (0.061) MAX. 7° TYP. 0.254-+ 0 0.0.007561 + 0.003) (0.010- 0.002) 5.10 MAX. (0.201) 3.10 (0.122) 3.90 (0.154) 0.51 (0.021) MIN. 2.54 (0.100) TYP. 1.78 ± 0.15 0.40 (0.016) (0.070 ± 0.006) 0.56 (0.022) DIMENSIONS IN MILLIMETERS (INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW4562) 11.15 ± 0.15 (0.442 ± 0.006) LAND PATTERN RECOMMENDATION 8 7 6 5 9.00 ± 0.15 (0.354 ± 0.006) 13.56 (0.534) 1 2 3 4 1.3 2.29 (0.051) (0.09) 1.55 12.30 ± 0.30 (0.061) (0.484 ± 0.012) MAX. 11.00 MAX. (0.433) 4.00 MAX. (0.158) 1.78 ± 0.15 (0.070 ± 0.006) 1.00 ± 0.15 0.75 ± 0.25 (0.039 ± 0.006) + 0.076 2.54 (0.030 ± 0.010) 0.254- 0.0051 (0.100) BSC + 0.003) (0.010- 0.002) DIMENSIONS IN MILLIMETERS (INCHES). 7° NOM. LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 4

Solder Reflow Temperature Profile 300 PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. PEAK PEAK TEMP. TEMP. 245°C 240°C PEAK TEMP. C) 200 230°C E (° 2.5°C ± 0.5°C/SEC. SOLDERING TUR 116500°°CC S3E0C. 2T0IM0°EC A 140°C ER 30 P 3°C + 1°C/–0.5°C SEC. M TE 100 PREHEATING TIME 150°C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL ROOM TEMPERATURE LOOSE 0 0 50 100 150 200 250 TIME (SECONDS) Note: Non-halide flux should be used. Recommended Pb-Free IR Profile TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATURE tp 20-40 SEC. *260 +0/-5 °C Tp 217 °C TL RAMP-UP RE 3 °C/SEC. MAX. RAMP-DOWN ATU Tsmax 150 - 200 °C 6 °C/SEC. MAX. ER Tsmin P TEM PREtHsEAT tL 60 to 150 SEC. 60 to 180 SEC. 25 t 25 °C to PEAK TIME NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C Note: Non-halide flux should be used. * Recommended peak temperature for widebody 400 mils package is 245°C Regulatory Information The devices contained in this data sheet have been approved by the following organizations: UL IEC/EN/DIN EN 60747-5-2 Recognized under UL 1577, Component Recognition Approved under: Program, File E55361. IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 CSA DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 Approved under CSA Component Acceptance Notice #5, (HCNW4562 only) File CA 88324. 5

Insulation and Safety Related Specifications 8-Pin DIP Widebody (300 Mil) (400 Mil) Parameter Symbol Value Value Units Conditions Minimum External L(101) 7.1 9.6 mm Measured from input terminals to Air Gap (External output terminals, shortest distance Clearance) through air. Minimum External L(102) 7.4 10.0 mm Measured from input terminals to Tracking (External output terminals, shortest distance Creepage) path along body. Minimum Internal 0.08 1.0 mm Through insulation distance, Plastic Gap conductor to conductor, usually the (Internal Clearance) direct distance between the photo- emitter and photodetector inside the optocoupler cavity. Minimum Internal NA 4.0 mm Measured from input terminals to Tracking (Internal output terminals, along internal cavity. Creepage) Tracking Resistance CTI 200 200 Volts DIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index) Isolation Group IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW4562 ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 600 V rms I-IV for rated mains voltage ≤ 1000 V rms I-III Climatic Classification 55/85/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage V 1414 V IORM peak Input to Output Test Voltage, Method b* V x 1.875 = V , 100% Production Test with t = 1 sec, V 2652 V IORM PR m PR peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V x 1.5 = V , Type and sample test, V 2121 V IORM PR PR peak t = 60 sec, Partial Discharge < 5 pC m Highest Allowable Overvoltage* (Transient Overvoltage, t = 10 sec) V 8000 V ini IOTM peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 17, Thermal Derating curve.) Case Temperature T 150 °C S Input Current I 400 mA S,INPUT Output Power P 700 mW S,OUTPUT Insulation Resistance at T, V = 500 V R ≥ 109 Ω S IO S *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. 6

Absolute Maximum Ratings Parameter Symbol Device Min. Max. Units Note Storage Temperature T -55 125 °C S Operating Temperature T -40 85 °C A Average Forward Input Current I HCPL-4562 12 mA F(avg) HCNW4562 25 Peak Forward Input Current I HCPL-4562 18.6 mA F(PEAK) HCNW4562 40 Effective Input Current I HCPL-4562 12.9 mA rms F(EFF) Reverse LED Input Voltage (Pin 3-2) V HCPL-4562 1.8 V R HCNW4562 3 Input Power Dissipation P HCNW4562 40 mW IN Average Output Current (Pin 6) I 8 mA O(AVG) Peak Output Current (Pin 6) I 16 mA O(PEAK) Emitter-Base Reverse Voltage (Pin 5-7) V 5 V EBR Supply Voltage (Pin 8-5) V -0.3 30 V CC Output Voltage (Pin 6-5) V -0.3 20 V O Base Current (Pin 7) I 5 mA B Output Power Dissipation P 100 mW 2 O Lead Solder Temperature T HCPL-4562 260 °C LS 1.6 mm Below Seating Plane, 10 Seconds up to HCNW4562 260 °C Seating Plane, 10 Seconds Reflow Temperature Profile T Option See Package Outline RP 300 Drawings Section Recommended Operating Conditions Parameter Symbol Device Min. Max. Units Note Operating Temperature T HCPL-4562 -10 70 °C A Quiescent Input Current I HCPL-4562 6 mA FQ HCNW4562 10 Peak Input Current I HCPL-4562 10 mA F(PEAK) HCNW4562 17 7

Electrical Specifications (DC) T = 25°C, I = 6 mA for HCPL-4562 and I = 10 mA for HCNW4562 (i.e., Recommended I ) unless otherwise specified. A F F FQ Parameter Symbol Device Min. Typ.* Max. Units Test Conditions Fig. Note Base Photo I 13 31 65 µA I = 10 mA V ≥ 5 V 2, 6 PB F PB Current HCPL-4562 19.2 I = 6 mA F I ∆I / -0.3 %/°C 2 mA < I < 10 mA, 2 PB PB F Temperature ∆T V ≥ 5 V PB Coefficient I HCPL-4562 0.25 % 2 mA < I < 10 mA 2, 6 3 PB F Nonlinearity HCNW4562 0.15 6 mA < I < 14 mA F Input Forward V HCPL-4562 1.1 1.3 1.6 V I = 5 mA 5 F F Voltage HCNW4562 1.2 1.6 1.8 I = 10 mA F Input Reverse BV HCPL-4562 1.8 5 V I = 10 µA R R Breakdown HCNW4562 3 I = 100 µA R Voltage Transistor h 60 160 I = 1 mA, FE C Current Gain V = 1.25 V CE Current CTR HCPL-4562 45 % V = 1.25 V, 8, 9 4 CE Transfer Ratio HCNW4562 52 V ≥ 5 V PB DC Output V HCPL-4562 4.25 V G = 2, V = 9 V 4, OUT V CC Voltage HCNW4562 5.0 15 8

Small Signal Characteristics (AC) T = 25°C, I = 6 mA for HCPL-4562 and I = 10 mA for HCNW4562 (i.e., Recommended I ) unless otherwise specified. A F F FO Parameter Symbol Device Min. Typ.* Max. Units Test Conditions Fig. Note Voltage Gain G HCPL-4562 0.8 2.0 4.2 V = 1 V 1 6 V IN P-P (0.1 MHz) HCNW4562 3.0 G Temperature ∆G /∆T -0.3 %/°C V = 1 V , 1, 11 V V IN P-P Coefficient f = 0.1 MHz REF Base Photo ∆i HCPL-4562 1.1 3.0 -dB V = 1 V , 3, 10, PB IN P-P Current (6 MHz) HCNW4562 0.36 f = 0.1 MHz 12 REF Variation -3 dB Frequency i HCPL-4562 6 15 MHz V = 1 V , 3, 10, 7 PB IN P-P (i ) (-3 dB) HCNW4562 13 f = 0.1 MHz 12 PB REF -3 dB Frequency G HCPL-4562 6 17 MHz V = 1 V , 1, 11 7 V IN P-P (G ) (-3 dB) HCNW4562 9 f = 0.1 MHz V REF Gain Variation ∆G HCPL-4562 1.1 3.0 -dB T = 25°C V = 1 V , 1, 11 V A IN P-P (6 MHz) HCNW4562 0.54 f = 0.1 MHz REF HCPL-4562 0.8 T = -10°C A 1.5 T = 70°C A ∆G HCPL-4562 1.15 -dB V = 1 V , V IN P-P (10 MHz) HCNW4562 2.27 f = 0.1 MHz REF Differential HCPL-4562 ±1.0 % I = 0.7 mA p-p, 3, 7 8 Fac Gain at I = 3 to 9 mA Fdc f = 3.58 MHz HCNW4562 ±0.9 I = 1 mA p-p, Fac I = 7 to 13 mA Fdc Differential HCPL-4562 ±1 deg. I = 0.7 mA p-p, 3, 7 9 Fac Phase at I = 3 to 9 mA Fdc f = 3.58 MHz HCNW4562 ±0.6 I = 1 mA p-p, Fac I = 7 to 13 mA Fdc Total Harmonic THD HCPL-4562 2.5 % V = 1 V , 4 10 IN P-P Distortion HCNW4562 0.75 f = 3.58 MHz, G = 2 V Output Noise V(noise) 950 µV rms 10 Hz to 10 MHz 1 O Voltage Isolation Mode IMRR HCPL-4562 122 dB f = 120 Hz, G = 2 14 11 V Rejection Ratio HCNW4562 119 9

Package Characteristics All Typicals at T = 25°C A Parameter Sym. Device Min. Typ. Max. Units Test Conditions Fig. Note Input-Output V HCPL-4562 3750 V rms RH ≤50%, 5, 12 ISO Momentary HCNW4562 5000 t = 1 min., 5, 13 Withstand HCPL-4562 5000 T = 25°C 5, 13 A Voltage* (Option 020) Input-Output R HCPL-4562 1012 Ω V = 500 Vdc 5 I-O I-O Resistance HCNW4562 1012 1013 T = 25°C A 1011 T = 100°C A Input-Output C HCPL-4562 0.6 pF f = 1 MHz 5 I-O Capacitance HCNW4562 0.5 0.6 *The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203E. Notes: 1. When used in the circuit of Figure 1 or Figure 4; G = V /V ; I = 6 mA (HCPL-4562), I = 10 mA (HCNW4562). V OUT IN FQ FQ 2. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (HCPL-4562). 3. Maximum variation from the best fit line of I vs. I expressed as a percentage of the peak-to-peak full scale output. PB F 4. CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I , to the forward LED input current, I, times 100%. O F 5. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together. 6. Flat-band, small-signal voltage gain. 7. The frequency at which the gain is 3 dB below the flat-band gain. 8. Differential gain is the change in the small-signal gain of the optocoupler at 3.58 MHz as the bias level is varied over a given range. 9. Differential phase is the change in the small-signal phase response of the optocoupler at 3.58 MHz as the bias level is varied over a given range. 10. TOTAL HARMONIC DISTORTION (THD) is defined as the square root of the sum of the square of each harmonic distortion component. The THD of the isolated video circuit is measured using a 2.6 kΩ load in series with the 50 Ω input impedance of the spectrum analyzer. 11. ISOLATION MODE REJECTION RATIO (IMRR), a measure of the optocoupler’s ability to reject signals or noise that may exist between input and output terminals, is defined by 20 log [(V /V )/(V /V )], where V is the isolation mode voltage signal. 10 OUT IN OUT IM IM 12. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for 1 second (leakage detec- tion current limit, I ≤5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related I-O Characteristics Table, if applicable. 13. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for 1 second (leakage detec- tion current limit, I ≤5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related I-O Characteristics Table, if applicable. 10

162 Ω (HCPL-4562) 90.9 Ω (HCNW4562) Figure 1. Gain and bandwidth test circuit 162 Ω (HCPL-4562) 90.9 Ω (HCNW4562) Figure 2. Base photo current test circuit Figure 3. Base photo current frequency response test circuit Figure 4. Recommended isolated video interface circuit 11

HCPL-4562 HCNW4562 100 mA IF – + AGE 10 V–F T L O D V TA = 70 °C R 1.0 A W TA = 25 °C R FO TA = -10 °C T 0.1 U P N – I F 0.01 I 1.0 1.1 1.2 1.3 1.4 1.5 VF – FORWARD VOLTAGE – V Figure 5. Input current vs. forward voltage HCPL-4562 fig 5a HCPL-4562 HCNW4562 80 A – µ 70 T N 60 E R UR 50 C O 40 T HO 30 TA = 25 °C E P VPB > 5 V S 20 A B – 10 B P I 0 0 2 4 6 8 10 12 14 16 18 20 IF – INPUT CURRENT – mA Figure 6. Base photo current vs. input current HCPL-4562 fig 6a HCPL-4562 HCNW4562 1.02 2 S E E R 1 1 G GAIN PHASE – DE AL 0.98 0 SE N A G H L-SI 0.96 NORMALIZED GAIN -1 AL P AL IF = 6 mA GN SM 0.94 fT =A 3=. 5285 M°CHz -2 LL-SI SEE FIG. 3 A M 0.92 -3 S 0 2 4 6 8 10 12 14 16 18 20 IF – INPUT CURRENT – mA Figure 7. Small-signal response vs. input current HCPL-4562 fig 7a 12

O HCPL-4562 HCNW4562 TI 1.04 A R R 1.02 E F 1.00 S N A 0.98 R T T 0.96 NORMALIZED N TA = 25 °C RE 0.94 IF = 6.0 mA CUR 0.92 VVCPBE => 15. 2V5 V D E 0.90 Z ALI 0.88 M R 0.86 O -10 0 10 20 30 40 50 60 70 N T – TEMPERATURE – °C Figure 8. Current transfer ratio vs. temperature HCPL-4562 fig 8a O ATI HCPL-4562 HCNW4562 R 1.10 R E F NS 1.00 VCE = 5.0 V A R T T 0.90 EN VCE = 1.25 V R 0.80 R U C D 0.70 NORMALIZED ZE TA = 25 °C VCE = 0.4 V MALI 0.60 IVFC =E 6= m1.A25 V OR VPB > 5 V N 0.50 – 0 2 4 6 8 10 12 14 16 18 20 R CT IF – INPUT CURRENT – mA Figure 9. Current transfer ratio vs. input current HCPL-4562 fig 9a B N – d -0.9 HCPL-4562 HCNW4562 O TI -1.1 A FREQUENCY = 6 MHz RI -1.3 A V T -1.5 N RE -1.7 R FREQUENCY = 10 MHz U -1.9 C O T -2.1 O E PH -2.3 TFAR E=F 2 =5 0°.C1 MHz S -2.5 A B – B -2.71 2 3 4 5 6 7 8 9 10 11 12 P i∆ IFQ – QUIESCENT INPUT CURRENT – mA Figure 10. Base photo current variation vs. bias conditions HCPL-4562 fig 10a 13

HCPL-4562 HCNW4562 3 B d 2 N – 1 TA = -10 °C AI G 0 E TA = 25 °C G -1 A LT -2 TA = 70 °C O D V -3 ZE -4 NORMALIZED LI TA = 25 °C MA -5 f = 0.1 MHz OR -6 N -7 0.01 0.1 1.0 10 100 100010,000100,000 f – FREQUENCY – KHz Figure 11. Normalized voltage gain vs. frequency HCPL-4562 fig 11a B HCPL-4562 HCNW4562 – d 0.5 NT 0 E R -0.5 R O CU -1.0 NORMALIZED T -1.5 TA = 25 °C HO -2.0 f = 0.1 MHz P SE -2.5 A B -3.0 D E -3.5 Z ALI -4.0 M R -4.5 O 0.01 0.1 1.0 10 100 100010,000100,000 N f – FREQUENCY – KHz Figure 12. Normalized base photo current vs. frequency HCPL-4562 fig 12a HCPL-4562 HCNW4562 0 -25 IPB PHASE SEE FIGURE 3 S -50 E E -75 GR TA = 25 °C E -100 D – -125 E S -150 VIDEO INTERFACE HA CIRCUIT PHASE – P -175 SEE FIGURE 4 ∅-200 -225 -250 0 2 4 6 8 10 12 14 16 18 20 f – FREQUENCY – MHz Figure 13. Phase vs. frequency HCPL-4562 fig 13a 14

B d – HCPL-4562 HCNW4562 O 150 ATI TA = 25 °C R N 120 O TI -20 dB/DECADE SLOPE C E J 90 E R E D O 60 M N LATIO 30 IMRR = 20 LOG10 vOUGTv/vIM O S R – I 00.01 0.1 1.0 10 100 1000 10,000 R M f – FREQUENCY – KHz I Figure 14. Isolation mode rejection ratio vs. frequency HCPL-4562 fig 14a HCPL-4562 HCNW4562 6.0 V – 5.5 E G A T 5.0 L O V T 4.5 U P T OU 4.0 C D – 3.5 O V 3.0 50 100 150 200 250 300 350 400 450 hFE – TRANSISTOR CURRENT GAIN Figure 15. DC output voltage vs. transistor current gain HCPL-4562 fig 15a S HCNW4562 VCC – I1000 R9 ICQ4 = 2 mA RRENT 890000 PISS ( m(mAW)) U ADDITIONAL T C 700 Q4 BUFFER PU 600 STAGE N Q3 Q5 P, IS 500 – 400 R R11 VOUT WE 300 O 200 LOW P R10 R12 ILMOPAEDDANCE TPUT 1000 U 0 25 50 75 100 125 150 175 O TS – CASE TEMPERATURE – °C Figure 16. Output buffer stage for low imped- Figure 17. Thermal derating curve, dependence of ance loads safety limiting value with case temperature per IEC/ HCPL-4562 fig 17b EN/DIN EN 60747-5-2 15 HCPL-4562 fig 16

V G V R I = E �≈ V E 10 (1) FQ R (�I /�I ) R R 4 PB F 7 9 V G V R I = E �≈ V E 10 (1) FQ i ≈� RV4 /R(�IPB/�IF) R7R9 (2) Fpp--pp IN 4 iiFFpppp--pp--pp≈� �V≈INiP/BRpp4--pp = VINpp--pp ((32)) I I V FQ PBQ E i i V Fpp--pp �≈ PBpp--pp = INpp--pp (3) I I i V V FacFtQor (MFP)B:Q F((pp--pp))E= INpp--pp (4) 2 I 2 V i FQ V E Factor (MF): F((pp--pp))= INpp--pp (4) 2 I 2 V VIOFQ==VCRVCE4–�≈VB(E�4–IGPBFVQR/R�V1I9E0F[)RVR1B07ERXE9- (IPBQ - IBXQ) R7] ((51)) R V = V –V – 9[V - (I - I ) R ] (5) O CC BE BEX PBQ BXQ 7 iFpp--pp≈� VIN/R4 4 R10 (2) G V R Conversion from HCPL-4562 to HCNW4562 IiPFBppQ--pp�≈�≈iVPRB7ppRE--pp91=0 VINpp--pp ((36)) IIFQ �≈ GVIPVBEQR10 VE (6) In order to obtain similar circuit performance when FigPBuQre 15 RshRows the dependency of the DC output 7 9 converting from the HCPL-4562 to the HCNW4562, FvoIalctatogr≈�e (oVMnCF Ch)F-:EX2.iFV((ppB--pEp))=VINpp--pp ((47)) it is recommended to increase the Quiescent Input BXQ R h2 I 2 V For 9 V < V 6 < 1F2E XVFQ, select thEe value of R such that Current, I , from 6 mA to 10 mA. If the application circuit V CC- 2 V 11 FQ I ≈� CC BE (7) in Figure 4 is used, then potentiometer R4 should be BXQ R h V 6 FE4X.2R5 V adjusted appropriately. VI = V≈� –OV� – 9[V� 9.0-m(IA - I ) R ] ((58)) OCQQ44 CCR BE447R0 BEX PBQ BXQ 7 11 10 Design Considerations of the Application Circuit V 4.25 V I ≈� O � � 9.0 mA (8) ThCeQQ 44voltRage g4a7in0 of the second stage (Q ) is Tsehvee raapl pfeÏiactautrieosn t hcairtc hueitl pi nm Faixgimurizee 4t hien cboarnpdowraidteths apIRPRpB1r9Q0ox�≈*im1Ga+Vt1e1VslyER Re1q0uCal to1:+ 1 3((96)) pimeprfoorrtamnat nocfe t hoefs et hfeea tHuCrePsL i-s4 5p6ea2k/eHdC NreWsp4o5n6s2e. oMf tohset RR9 * R7R99 CQ31 2� R1�11 fT44 (9) 10 1 + s R C + detector circuit that helps extend the frequency range 9 CQ3 2� R� f onthvueem rc bwheohr iicocefh g otahfi enD svCto albgtaieagsse, t phgoeai niontv sie sar arreelll acatilrilvc eucloiytn tcsooepqnouslteoangncyte., saT nhodef IRnIGcB rXVaeQna≈�≈s�diVV nVtVOghICUN ReCRT 6′-1�l≈o1h 2a(F��R�dEIIV′IX P1FB1iBm EinpcRRRelu4d7RdRRa1en90sc eth) eo 1rp1 arerTa4d4lluecl incogm Rb in(kaetieo(pn1(in 70og))f the desire to maximize bandwidth performance. Rw19GI1/hRVe10r≈� er≈�attVyOioIpUVN TiOcco�a≈n�llsy�t4aIPnF.�B2tI)5P BwRVi4l7lR� =im19900p.0.r0om0v3eA2 the bandwid9th. (1(80)) TLEoD u qseu itehsec ecnirtc cuuitr,r fiernstt bsye:lect R1 to set VE for the desired Ibwf ahiCntQeQ d4r4iwes itndyRetphc1ic1e amslslaayyr4y �7� aI0ItPlFosBo d b=riev0 ep. 0ra0e 3sloe2wrv eidm pbeyd aandcdein lgo aadn, additional emitte�r IfFollowing the buffer stage (Q in V G V R R 1 5 I = E �≈ V E 10 (1) Figu9re* 16), in which case R can be increased( 9to) FQ R4 (�IPB/�IF) R7R9 seRt 1IC0Q4 ≅1 2+ mAs.R9 CCQ3 + 2� R11�1 f 11 T44 For a constant value V , the circuit topology Finally, adjust R to achieve the desired voltage gain. i ≈� V /R INp-p (2) 4 (aFdppj--uppstinIgN th4e gain with R ) preserves linearity by V G V R koeIniFeF QVppp--=ppi.ngR�≈ E4tihP�≈eB ppm(--pp�oI=PdBVu/V�laIINEtFppi)o--ppnR1 07fRa9c4tor (MF) dependent o((n31ly)) GV ≈� VOUT �≈ �IPB R7R9 (10) IFQE V IPBQ G VVER VIN �IF R4R10 I = E �≈ V E 10 (1) FiiIIIaiFFFFFFIFcppppQQQQFpp--t--Qpppp--o===pp≈≈r�� RRR�VVV(VV≈MEEE444IINNiFIP���//≈≈≈PBRR)Bp:p44Q(((--pp���2iFIII=GGGPPP(I(ppBBBFVVV-Q-///Vpp���)VVVIV)IIINEEEFFFE=pp)))--RRRpVpRRR2111I000N777VRRRppE--999pp (((((((4311122))))))) Dwehfienrietiotynp:ically ��IIPFB = 0.0032 R (�I /�I ) R R 4 PB F 7 9 VFMiiiOaiFFoIFcppppF=dpp--t--Qpppp--uopp≈≈≈Vlr���aC�(tVVV≈CiMoIINN–inFIP///PBRRRV)Bp:Bp44Q--Eppi4F–=((pp-R-VpRp)I1V)9N0E=pp[--VpVpBINEppX--pp- (IPBQ - IBXQ) R7] ((((((543222)))))) GI V == VQouliteasgcee nGta LinED forward current FaiiiFIIFFFcppFFpppppp-t-QQpp------oppppppr���(≈≈≈MINiiiFIIPPPPPBBB)BBppp:ppp4QQ------pppppp2iF===(I(ppF-Q-VVVpp)IIIVV)NNNEE=pppppp------pppVppp2INVppE--pp ((((4333)))) iFpF-Qp = Pcuerarke-ntot-peak small signal LED forward VVFVFVFVFooIIIOOOOnaaaPBPIrlcccBBFX=====y tttaQQQQ ooow VVVVVgrrr≈��≈≈�iCCCCti(((vhCCCCVMMMGGe Ch–––––nVVRFFFICRRFP EVVVVV)))6VVGB77X-:::BBBB.RREEQhVEEEE,2RR2222iii99F 4444FFFV–––––E11V(((IIII00EX(((ppppppFFFF,B ---QQQQRRRR---pppEaRRRRRppp)))n1111V)))999990000dE===[[[[[ VVVVVVVVV2222CBBBBIIINNNCEEEE,VVVV ppppppXXXXDEEEE------pppppp-----C (((((oIIIIIPPPPuBBBBtQQQQpu-----t IIIIIvBBBBoXXXXlQQQQt)))))agRRRRRe7777 ]]]]]will v(((((((((((55555a444766r)))))))))))y ViVPIINBPBppBE--QXpp ==== PPbQBeeaausaasieeekk- s--pEttcoomhe--onppittteeto beaa crakk usv sserommr leptaanahllgtllo ssetiio ggo nncf uaaHllrC rienPnpLt-u4t5 v6o2l/ta ge IO �≈CCGV VBEER410 R10 BEX PBQ BXQ 7 (6) HCNW4562 transistor WPhBeQre: V 4.25 V IIIIBPPCBBXQQQQQ44≈��≈≈�≈� VGGGRCVVRCRR1O16VVV7-RREE�h2RRR9FE11V400XB7E0 � 9.0 mA ((((8766)))) IBXQ = QHCuNieWsc4e5n6t 2b atrsaen csuisrtroernt of HCPL-4562/ 1awwnIIIII6RGIRGIRGIRIRIRBBBPBhhRRRRRRdCCCCCBXXXX111111VVVQQQQQeeQQQQQ,999999QQQQQ00000044444rr44444≈≈≈���ee≈≈≈≈�≈******����≈≈≈≈≈�����VVVtt111111VVVyyVVVVOOORRRRRIIppCCCCUUU++++++VVVVVNNVRRRRCCCCRR11111TTTiiOOOOOcc111116666777ssssss----���aa≈≈≈RRE�����hhhhllRRRRRR2222ll999FFFF���yy���EEEE9999991I4I4I444VVVV44444III0XXXXPPPFF.....��BBBB77777CCCCCC�BBB22222EEEEII00000ICCCCCC55555PPFQQQQQQBBRRRVVVVVRRR33333311111144777++++++RRR�����==RRR11999999990022222200.....������00000..00RRRRRRmmmmm00111111������11111133AAAAA11111122ffffffTTTTTT444444444444 (((111((((((((((((((((9999998888877776000))))))))))))))))))) ChCfQFTVE43X E ==== CHVrUEteoffounCs eglriiNttrscrayetWotgo niguver4ta en 5RGai dn6c4caa2 rfiopnr tesa r(qsacI Cnuie/tsIemaBinn)s itoctcotyefer Horfr fCdo QPemgL5 -ec4no5le6ler2ac/tt ioo rn o f Q3 IN F�I 4 10 V �I F R R wGGGhVVVer≈≈≈���eVVtVVVyOOOIIpUUUNNTTTic���a≈≈≈ll��y���IIIIIPPPFF��BBBIIPFBRRRRR44777RRR=RR11999000.0032 (((111000))) IN F 4 10 �I wwhheerreettyyppiiccaallllyy ���IIIPPBB == 00..00003322 wheretypically �IPFFB = 0.0032 �I F

For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2005-2008 Avago Technologies Limited. All rights reserved. Obsoletes AV01-0571EN AV02-1361EN - June 23, 2008

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: B roadcom Limited: HCNW4562 HCNW4562#300 HCNW4562#500 HCNW4562-000E HCNW4562-300E HCNW4562-500E HCPL- 4562 HCPL-4562#020 HCPL-4562#060 HCPL-4562#300 HCPL-4562#320 HCPL-4562#500 HCPL-4562#520 HCPL-4562-000E HCPL-4562-020E HCPL-4562-060E HCPL-4562-300E HCPL-4562-320E HCPL-4562-500E HCPL-4562-520E