EXTREME ADVANCED ENGINEERING TEMPERATURE Technical Data Sheet Technical Data Sheet Put-Ups Wall Expansion Range Nominal Part Bulk Shop Available Diameter Thickness Size # Min. Max. Spool Spool Colors UL Recognized: VW-1 ±0.005” 24 0.022” FGLG.24 0.005” 0.020” 0.027” 500’ 250’ 6 For High Temp - Low Voltage 22 0.027” FGLG.22 0.005” 0.025” 0.032” 500’ 250’ 6 Applications 20 0.034” FGLG.20 0.009” 0.032” 0.039” 500’ 250’ 6 18 0.042” FGLG.18 0.011” 0.040” 0.049” 500’ 250’ 6 Easy To Install-Cuts With 16 0.053” FGLG.16 0.011” 0.051” 0.061” 500’ 250’ 6 Scissors 14 0.066” FGLG.14 0.011” 0.064” 0.072” 500’ 250’ 6 12 0.085” FGLG.12 0.011” 0.081” 0.089” 250’ 100’ 6 Resists Most Organic Solvents 11 0.095” FGLG.11 0.011” 0.091” 0.101” 250’ 100’ 6 10 0.106” FGLG.10 0.011” 0.102” 0.112” 250’ 100’ 6 Cut And Abrasion Resistant 9 0.118” FGLG.09 0.011” 0.114” 0.124” 250’ 100’ 6 8 0.133” FGLG.08 0.011” 0.129” 0.141” 250’ 100’ 6 7 0.148” FGLG.07 0.013” 0.144” 0.158” 250’ 100’ 6 6 0.166” FGLG.06 0.013” 0.162” 0.178” 250’ 100’ 6 5 0.186” FGLG.05 0.013” 0.182” 0.198” 250’ 100’ 6 4 0.208” FGLG.04 0.016” 0.204” 0.224” 250’ 100’ 6 3 0.234” FGLG.03 0.016” 0.229” 0.249” 250’ 100’ 6 2 0.263” FGLG.02 0.016” 0.258” 0.278” 250’ 100’ 6 1 0.294” FGLG.01 0.016” 0.289” 0.311” 100’ 50’ 6 0 0.330” FGLG.00 0.016” 0.325” 0.347” 100’ 50’ 6 3/8” 0.375” FGL0.38 0.016” 0.375” 0.399” 100’ 50’ 6 7/16” 0.438” FGL0.44 0.018” 0.438” 0.462” 100’ 50’ 6 1/2” 0.500” FGL0.50 0.018” 0.500” 0.524” 100’ 50’ 6 5/8” 0.625” FGL0.63 0.018” 0.625” 0.655” 100’ 50’ 6 3/4” 0.750” FGL0.75 0.018” 0.750” 0.786” 100’ 50’ 6 1” 1.000” FGL1.00 0.018” 1.000” 1.040” 100’ 50’ 6 Heat Treated, Fray-Resistant Colors Fiberglass Sleeving Available: 6 = WH, NT, YL RD, BL, BK Cut Cleanly Techflex® INSULTHERM TRU-FIT (FGL) is a braided fiberglass sleeving which has been heat treated and Scissors impregnated with an acrylic binder to reduce fraying and dusting, and improve usability and performance. Material FGL is engineered for applications where temperatures as high as 1,200ºF may be encountered. FGL is used as primary Acrylic Coated Fiberglass insulation on low voltage applications such as leads in toasters, coffee makers, ranges and other appliances. FGL Grade may also be used as insulation and protection for small FGL heaters and resistors that operate at high temperatures, and to insulate over soldered connections when exposure to sol- Wall Thickness der melt temperatures is possible. Refer to Chart Insultherm Tru-Fit provides a sturdy, long lasting and inex- pensive insulation solution. It is flexible and expandable, Drawing Number and can easily be installed over applications with irregular TF001INS-WD shapes and tight turns. Standard color are Black and Natural, but other colors are available by special order. Contact your Account representative for details. Colors Available: www.techflex.com 800.323.5140 • 973.300.9242 • fax: 973.300.9409 VW-1 104 Demarest Road • Sparta, NJ 07871 White (WH), Natural (NT), Yellow (YL), Red (RD), Blue (BL), Black (BK).

EXTREME ADVANCED ENGINEERING TEMPERATURE TTeecchhnincaicl aDla tDa aSthae eStheet Melt Point ASTM D-2117 2,048°F (1,120°C) ABRASION FLAMMABILITY Maximum Continuous Mil-I-23053 Abrasion Resistance Rating ____________________ UL VW-1 1,202°F (650°C) w Very High w w . Abrasion Test Machine t e Taber 5150 c h Minimum Continuous f l Abrasion Test Wheel -94°F (-70°C) ex Calibrase H-18 CHEMICAL .c o m RESISTANCE Abrasion Test Load 500g 1=No Effect 4=More Affected Room Temperature PHYSICAL 2=Little Effect 5=Severely Affected 75°F 3=Affected PROPERTIES Humidity 15% Aromatic Solvents ________________ 1 Monofilament Diameter_________ NA Slight Fraying ASTM D-204 Aliphatic Solvents _________________ 1 200 Test Cycles Flammability Rating __________ VW-1 Chlorinated Solvents ______________ 1 Slight Fraying Weak Bases ______________________ 1 Recommended Cutting _______ Scissor 1,000 Test Cycles Colors __________________________6 Salts ____________________________ 1 Fraying Strong Bases _____________________ 1 Wall Thickness ____________.005”-.018” 1,700 Test Cycles Specific Gravity ASTM D-792 __ 1.0-1.8 Salt Water 0-S-1926 ________________ 1 Moisture Absorption ____________ .01 Material Destroyed Hydraulic Fluid MIL-H-5606 _________ 1 % ASTM D-570 2,300 Test Cycles Lube Oil MIL-L-7808 _______________ 1 TML __________________________.02 Pre-Test Weight De-Icing Fluid MIL-A-8243 __________ 1 CVCM ________________________ .01 15.3 g Strong Acids _____________________ 2 WVR __________________________ .00 Post-Test Weight Strong Oxidants __________________ 2 Outgassing ___________________ Low 13.6 g Esters/Ketones ___________________ 1 Test End Loss Of Mass UV Light ________________________ 2 Point Of Destruction Petroleum _______________________ 1 11% Fungus ASTM G-21 ________________ 1 Halogen Free ___________________Yes RoHS __________________________Yes SVHC ________________________None © 2020 Techflex® - Any unauthorized reproduction, in whole or part, in any medium whatsoever, without the express written permission of Techflex® is strictly forbidden. Techflex® product names and logos are registered trademarks of Techflex®, unless otherwise attributed. The contents and illustrations contained herein are believed to be reliable. Techflex® makes no warranties as to their accuracy or completeness and disclaims any liability in connection with their use. Techflex’s® only obligations are those in standard terms of sale for these products and Techflex® will not be liable for any consequential or other damages arising due to misuse of these products or typographical errors or omissions. Users should make their own evaluation to determine the suitability of these products for their unique and specific applications. 01-08