ALUMINUM ELECTROLYTIC CAPACITORS UUP 6mmL Chip Type, Bi-Polarized Chip type, bi-polarized withstanding high temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). UUP AEC-Q200 compliant. Please contact us for details. UUN Extended range High Temperature Specifications UWP Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 47µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) 6.3 10 16 25 35 50 tan δ (MAX.) 0.24 0.20 0.17 0.17 0.15 0.15 Measurement frequency : 120Hz Rated voltage (V) 6.3 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z–25°C / Z+20°C 4 3 2 2 2 2 ZT / Z20 (MAX.) Z–40°C / Z+20°C 8 6 4 4 3 3 The specifications listed at right shall be met Capacitance change Within ±20% of the initial capacitance value when the capacitors are restored to 20°C after Endurance the rated voltage is applied for 1000 hours at tan δ 200% or less than the initial specified value 105°C with the polarity every 250 hours. Leakage current Less than or equal to the initial specified value After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value Resistance to soldering maintained at 250°C. The capacitors shall meet the characteristic heat requirements listed at right when they are removed from the plate tan δ Less than or equal to the initial specified value and restored to 20°C. Leakage current Less than or equal to the initial specified value Marking Black print on the case top. Chip Type Type numbering system (Example : 16V 10µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 105˚C Marking Capacitance Plastic platform AX. U U P 1 C 1 0 0 M C L 1 G S Lot No. Voltage 0.3MAX. C±0.2 5M Taping code 0. (mm) Configuration A2P1016V D±0.5φ B±0.2 A±0.2A±0.2E CABφD1444...833 2555...133 2666....4663 CapaRcaittaendcR ceaa ttpoealdec rviatoanlntcacege e( (± 1(21006µ%VF))) E 1.0 1.3 2.2 5.8±0.3 0.5 to 0.8 Series name Type Voltage mark for 6.3V is 6V Dimensions V 6.3 10 16 25 35 50 Cap.(µF) Code 0J 1A 1C 1E 1V 1H 0.1 0R1 4 1.0 0.22 R22 4 2.0 0.33 R33 4 2.8 0.47 R47 4 4.0 1 010 4 8.4 2.2 2R2 4 8.4 5 13 3.3 3R3 5 12 5 16 5 17 4.7 4R7 4 12 5 16 5 18 6.3 20 10 100 4 17 5 23 6.3 27 6.3 29 22 220 5 28 6.3 33 6.3 37 33 330 6.3 37 6.3 41 6.3 49 Rated 47 470 6.3 45 Case size ripple φD(mm) Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Taping specifications are given in page 23. Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more Recommended land size, soldering by reflow are given in page 18, 19. Coefficient 0.70 1.00 1.17 1.36 1.50　　 Please select UUN(p.166) if high CV products are required. Please refer to page 3 for the minimum order quantity. 124 CAT.8100H

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N ichicon: UUP1E100MCL1GS UUP1C220MCL1GS UUP1E4R7MCL1GS UUP1H4R7MCL1GS UUP0J220MCL1GS UUP0J330MCL1GS UUP0J470MCL1GS UUP1A100MCL1GS UUP1A220MCL1GS UUP1A330MCL1GS UUP1C4R7MCL1GS UUP1C330MCL1GS UUP1E3R3MCL1GS UUP1V2R2MCL1GS UUP1V3R3MCL1GS UUP1H0R1MCL1GS UUP1HR22MCL1GS UUP1HR33MCL1GS UUP1HR47MCL1GS UUP1H010MCL1GS UUP1H2R2MCL1GS UUP1H3R3MCL1GS UUP1C100MCL1GS UUP1V100MCL1GS UUP1HR47MCL1GB UUN2A470MNQ1ZD