ALUMINUM ELECTROLYTIC CAPACITORS ULR Chip Type, High Voltage. Chip Type, high Voltage. Applicable to automatic mounting machine using carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. ULV Long Life ULR High Voltage UUX Specifications Item Performance Characteristics Category Temperature Range –40 to +105°C Rated Voltage Range 160 to 500V Rated Capacitance Range 2.7 to 39µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.04CV +100(µA). Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) 160 200 250 400 450 500 tan δ (MAX.) 0.20 0.20 0.25 0.25 0.30 0.30 Measurement frequency: 120Hz Rated voltage (V) 160 200 250 400 450 500 Stability at Low Temperature Impedance ratio Z–40°C / Z+20°C 6 6 10 10 15 15 ZT / Z20 (MAX.) The specifications listed at right shall be met when the Capacitance change Within ±20% of the initial capacitance value Endurance capacitors are restored to 20°C after the rated voltage is tan δ 200% or less than the intial specified value applied for 3000 hours at 105°C. Leakage current Less than or equal to the initial specified value After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value Resistance to soldering maintained at 250°C and then performing voltage treatment based on tan δ Less than or equal to the initial specified value heat JIS C 5101-4 clause 4.1 at 20°C, they shall meet the characteristic Leakage current Less than or equal to the initial specified value requirements listed at right when they are removed from the plate. Marking Black print on the case top. Chip Type Type numbering system (Example : 400V 8.2µF) (φ8 , φ10) Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Voltage(2G : 400V) Series Plasti0c. 3pMlaAtfoXr.m C±0.2 MAX. U L R 2 G 8 R 2 M N L 1 G S Lot No. 0.5 Trade mark A28.2 2GLR D±0.5φ B±0.2 EA±0.2A±0.2 TCaappinagc ictaondcee tolerCanocnefi g(u±r2a0ti%on) Capacitance L±1.0 H Rated capacitance (8.2µF) Negative Rated voltage (400V) Pressure relief vent (mm) Series name φD × L 8 × 10 10 × 10 10 × 13.5 Type A 2.9 3.2 3.2 B 8.3 10.3 10.3 C 8.3 10.3 10.3 Voltage E 3.1 4.5 4.5 V 160 200 250 400 450 500 L 10 10 13.5 H 0.8 to 1.10.8 to 1.10.8 to 1.1 Code 2C 2D 2E 2G 2W 2H Dimensions V 160 200 250 400 450 500 Cap.(µF) Code 2C 2D 2E 2G 2W 2H 2.7 2R7 8 × 10 20 3.9 3R9 8 × 10 25 10 × 10 35 4.7 4R7 8 × 10 35 5.6 5R6 10 × 13.5 40 6.8 6R8 10 × 10 40 8.2 8R2 10 × 10 50 10 100 8 × 10 35 10 × 13.5 45 12 120 8 × 10 50 10 × 13.5 55 15 150 8 × 10 50 10 × 10 50 22 220 10 × 10 65 10 × 13.5 55 27 270 10 × 10 65 33 330 10 × 13.5 70 Case size Rated 39 390 10 × 13.5 70 φD × L (mm) ripple Rated ripple current (mArms) at 105°C 120Hz Taping specifications are given in page 23. Frequency coefficient of rated ripple current Recommended land size, soldering by reflow are given Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more in page 18, 19. Coefficient 0.80 1.00 1.25 1.40 1.60 Please refer to page 3 for the minimum order quantity. 172