TNPU e3 www.vishay.com Vishay Draloric Ultra Precision Thin Film Chip Resistors FEATURES • Low temperature coefficient and tight tolerances • Sulfur resistance verified according to ASTM B 809 • Superior moisture resistivity (85 °C; 85 % RH) • Excellent overall stability at different environmental conditions  0.05 % (1000 h rated power at 70 °C) • AEC-Q200 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS TNPU e3 ultra precision thin film flat chip resistors combine • Industrial equipment the proven reliability of TNPW e3 products with a most • Telecommunication advanced level of precision and stability. This unique • Medical equipment combination makes the product perfectly suited for all applications with outstanding requirements towards size, • Instrumentation reliable precision and stability. • Test and measuring equipment • Automotive TECHNICAL SPECIFICATIONS DESCRIPTION TNPU0603 e3 TNPU0805 e3 TNPU1206 e3 Imperial size 0603 0805 1206 Metric size code RR1608M RR2012M RR3216M Resistance range 100  to 100 k 100  to 332 k 100  to 511 k Resistance tolerance ± 0.1 %; ± 0.05 %; ± 0.02 % Temperature coefficient ± 10 ppm/K; ± 5 ppm/K Rated dissipation, P (1) 0.1 W 0.125 W 0.25 W 70 Operating voltage, U AC /DC 75 V 150 V 200 V max. RMS Permissible film temperature, F max. (1) 125 °C 125 °C 125 °C Operating temperature range -55 °C to 125 °C -55 °C to 125 °C -55 °C to 125 °C Permissible voltage against ambient (insulation): 1 min; U 100 V 200 V 300 V ins FITobserved  0.1 x 10-9/h  0.1 x 10-9/h  0.1 x 10-9/h Note (1) Please refer to APPLICATION INFORMATION, see below. APPLICATION INFORMATION When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. Revision: 01-Jul-16 1 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPU e3 www.vishay.com Vishay Draloric MAXIMUM RESISTANCE CHANGE AT RATED DISSIPATION OPERATION MODE STANDARD TNPU0603 e3 0.100 W Rated dissipation, P TNPU0805 e3 0.125 W 70 TNPU1206 e3 0.250 W Operating temperature range -55 °C to 125 °C Permissible film temperature, F max. 125 °C TNPU0603 e3 100  to 100 k TNPU0805 e3 100  to 332 k TNPU1206 e3 100  to 511 k Max. resistance change at P70 for resistance range, |R/R| after: 1000 h  0.05 % 8000 h  0.1 % 225 000 h  0.3 % TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE TCR TOLERANCE RESISTANCE E-SERIES ± 10 ppm/K ± 0.05 % ± 0.1 % TNPU0603 e3 100  to 100 k ± 5 ppm/K ± 0.05 % ± 0.02 % ± 10 ppm/K ± 0.05 % ± 0.1 % 100  to 332 k TNPU0805 e3 E24; E192 ± 5 ppm/K ± 0.05 % ± 0.02 % 100  to 200 k ± 10 ppm/K ± 0.05 % ± 0.1 % 100  to 511 k TNPU1206 e3 ± 5 ppm/K ± 0.05 % ± 0.02 % 100  to 200 k Revision: 01-Jul-16 2 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPU e3 www.vishay.com Vishay Draloric PACKAGING PACKAGING TYPE / SIZE CODE QUANTITY PACKAGING STYLE WIDTH PITCH DIMENSIONS E52 = EN 1000 Tape and reel TNPU0603 e3 cardboard tape TNPU0805 e3 8 mm 4 mm Ø 180 mm / 7" acc. IEC 60286-3, TNPU1206 e3 ET1 = EA 5000 Type 1a PART NUMBER AND PRODUCT DESCRIPTION Part Number: TNPU12061K32AZEA00 T N P U 1 2 0 6 1 K 3 2 A Z E A 0 0 TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING TNPU0603 R = Decimal B = ± 0.1 % Y = ± 10 ppm/K EA TNPU0805 K = Thousand A = ± 0.05 % Z = ± 5 ppm/K EN TNPU1206 M = Million H = ± 0.02 % (4 digits) Product Description: TNPU1206 1K32 0.05 % T-16 ET1 e3 TNPU1206 1K32 0.05 % T-16 ET1 e3 TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING LEAD (Pb)-FREE TNPU0603 Examples: ± 0.1 % T-13 = ± 10 ppm/K ET1 e3 = Pure tin TNPU0805 1K32 = 1320  ± 0.02 % T-16 = ± 5 ppm/K E52 termination finish TNPU1206 ± 0.05 % Note • Products can be ordered using either the PART NUMBER or the PRODUCT DESCRIPTION. Revision: 01-Jul-16 3 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPU e3 www.vishay.com Vishay Draloric DESCRIPTION MATERIALS Vishay acknowledges the following systems for the Production is strictly controlled and follows an extensive regulation of hazardous substances: set of instructions established for reproducibility. A • IEC 62474, Material Declaration for Products of and for the homogeneous film of metal alloy is deposited on a high Electrotechnical Industry, with the list of declarable grade AI2O3 ceramic substrate and conditioned to achieve substances given therein (2) the desired temperature coefficient. Specially designed • The Global Automotive Declarable Substance List inner contacts are deposited on both sides. A special laser (GADSL) (3) is used to achieve the target value by smoothly fine trimming • The REACH regulation (1907/2006/EC) and the related list the resistive layer without damaging the ceramics. A further of substances with very high concern (SVHC) (4) for its conditioning is applied in order to stabilize the trimming supply chain result. The resistor elements are covered by a protective The products do not contain any of the banned substances coating designed for electrical, mechanical and climatic as per IEC 62474, GADSL, or the SVHC list, see protection. The terminations receive a final pure tin on nickel www.vishay.com/how/leadfree. plating. The result of the determined production is verified Hence the products fully comply with the following by an extensive testing procedure on 100 % of the individual directives: chip resistors. Only accepted products are laid directly into • 2000/53/EC End-of-Life Vehicle Directive (ELV) and the tape in accordance with IEC 60286-3 Type 1a (1). Annex II (ELV II) • 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment ASSEMBLY 2015/863/EU The resistors are suitable for processing on automatic • 2012/19/EU Waste Electrical and Electronic Equipment SMD assembly systems. They are suitable for automatic Directive (WEEE) soldering using wave, reflow or vapour phase as shown in Vishay pursues the elimination of conflict minerals from its IEC 61760-1 (1). The encapsulation is resistant to all supply chain, see the Conflict Minerals Policy at cleaning solvents commonly used in the electronics www.vishay.com/doc?49037. industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, potting compounds RELATED PRODUCTS and their processes, if applied, shall be qualified by For products with precision specification see the datasheet: appropriate means to ensure the long-term stability of the whole system. • TNPW e3 - High Stability Thin Film Flat Chip Resistors (www.vishay.com/doc?28758) The resistors are RoHS compliant, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. The immunity of the plating against tin whisker growth has been proven under extensive testing. Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. (2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474. (3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org. (4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table. Revision: 01-Jul-16 4 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPU e3 www.vishay.com Vishay Draloric FUNCTIONAL PERFORMANCE % 120 n wer i 100 o P d ate 80 R 60 40 20 0 -55 -25 0 25 50 75 100 125 150 175 70 Derating Ambient Temperature in °C B TNPU1206 e3 d 110 n TNPU0805 e3 i A3100 TNPU0603 e3 y irt ae 90 n iL -n 80 o N 70 60 40 100 1K 10K 100K 1M Non-Linearity Resistance Value in Ω V V/ µ n 1 e i s oi TNPU0805 e3 N nt TNPU0603 e3 e r r u C 0.1 TNPU1206 e3 0.01 100 1K 10K 100K 1M Resistance Value in Ω Current Noise Revision: 01-Jul-16 5 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPU e3 www.vishay.com Vishay Draloric TEST AND REQUIREMENTS All tests are carried out in accordance with the following The tests are carried out under standard atmospheric specifications: conditions in accordance with IEC 60068-1, 4.3, whereupon EN 60115-1, generic specification the following values are applied: EN 60115-8 (successor of EN 140400), Temperature: 15 °C to 35 °C sectional specification Relative humidity: 25 % to 75 % EN 140401-801, detail specification Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). IEC 60068-2-xx, test methods A climatic category LCT / UCT / 56 is applied, defined by the The parameters stated in the Test Procedures and lower category temperature (LCT), the upper category Requirements table are based on the required tests and temperature (UCT), and the duration of exposure in the permitted limits of EN 140401-801. The table presents only damp heat, steady state test (56 days). the most important tests, for the full test schedule refer to The components are mounted for testing on printed circuit the documents listed above. However, some additional boards in accordance with EN 60115-8, 2.4.2, unless tests and a number of improvements against those otherwise specified. minimum requirements have been included. The testing also covers most of the requirements specified by EIA / ECA-703 and JIS-C-5201-1. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 IEC 60068-2 (1) REQUIREMENTS TEST PROCEDURE CLAUSE TEST METHOD PERMISSIBLE CHANGE (R) Stability for product types: TNPU0603 e3 TNPU0805 e3 TNPU1206 e3 4.5 - Resistance ± 0.1 %; ± 0.05 %; ± 0.02 % Temperature At (20 / -55 / 20) °C 4.8 - ± 10 ppm/K; ± 5 ppm/K coefficient and (20 / 125 / 20) °C U = P x R or U = U ; 70 max. whichever is the less severe; 4.25.1 - Endurance at 70 °C 1.5 h on; 0.5 h off; 70 °C; 1000 h ± (0.05 % R + 0.01 ) 70 °C; 8000 h ± (0.1 % R + 0.02 ) Endurance at upper 125 °C; 1000 h ± (0.05 % R + 0.01 ) 4.25.3 - category temperature 125 °C; 8000 h ± (0.1 % R + 0.02 ) Damp heat, (40 ± 2) °C; 56 days; 4.24 78 (Cab) ± (0.1 % R + 0.01 ) steady state (93 ± 3) % RH 4.23 Climatic sequence: 4.23.2 2 (Bb) Dry heat UCT; 16 h 55 °C; 24 h; 4.23.3 30 (Db) Damp heat, cyclic > 90 % RH; 5 cycle 4.23.4 1 (Ab) Cold LCT; 2 h ± (0.1 % R + 0.02 ) 4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; (25 ± 10) °C 55 °C; 24 h; 4.23.6 30 (Db) Damp heat, cyclic > 90 % RH; 5 cycles U = P70 x R Umax.; 1 min 4.23.7 - D.c. load LCT = -55 °C UCT = 125 °C - 1 (Aa) Cold -55 °C; 2 h ± (0.05 % R + 0.01 ) Revision: 01-Jul-16 6 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPU e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS EN 60115-1 IEC 60068-2 (1) REQUIREMENTS TEST PROCEDURE CLAUSE TEST METHOD PERMISSIBLE CHANGE (R) Stability for product types: TNPU0603 e3 TNPU0805 e3 TNPU1206 e3 30 min at LCT and 30 min at UCT; Rapid change 4.19 14 (Na) LCT = -55 °C; ± (0.1 % R + 0.01 ) of temperature UCT = 125 °C; 1000 cycles U = 2.5 x P x R 70 4.13 - Short time or U = 2 x Umax.; ± (0.05 % R + 0.01 ) overload whichever is the less severe; 5 s Endurance by sweeping; 10 Hz to 2000 Hz; ± (0.05 % R + 0.01 ) 4.22 6 (Fc) Vibration no resonance; no visible damage amplitude  1.5 mm or  200 m/s2; 6 h Solder bath method; SnPb40; non-activated flux (215 ± 3) °C; (3 ± 0.3) s Good tinning ( 95 % covered); 4.17 58 (Td) Solderability Solder bath method; no visible damage SnAg3Cu0,5 or SnAg3,5; non-activated flux (235 ± 3) °C; (2 ± 0.2) s Resistance to Solder bath method; 4.18 58 (Td) ± (0.02 % R + 0.01) soldering heat (260 ± 5) °C; (10 ± 1) s Component solvent Isopropyl alcohol 4.29 45 (XA) No visible damage resistance +50 °C; method 2 RR 1608M; 9 N 4.32 21 (Ue3) Shear (adhesion) RR 2012M and No visible damage RR 3216M; 45 N ± (0.05 % R + 0.01) 4.33 21 (Ue ) Substrate bending Depth 2 mm, 3 times 1 no visible damage, no open circuit in bent position 4.7 - Voltage proof U = U ; 60 ± 5 s No flashover or breakdown RMS ins IEC 60 695-11-5 (1), 4.35 - Flammability No burning after 30 s needle flame test; 10 s U = 15 x P x R Periodic electric 70 or U = 2 x U ; overload: max. 4.39 - whichever is the less severe; ± (0.1 R + 0.02 ) Standard operation 0.1 s on; 2.5 s off; mode 1000 cycles Damp heat, (85 ± 5) °C; 56 days 4.37 67 (Cy) steady state, ± (0.25 R + 0.05 ) (85 ± 5) % RH accelerated IEC 61340-3-1 (1); 3 pos. + 3 neg. Electro static (equivalent to MIL-STD-883, 4.38 - discharge method 3015) ± (0.5 R + 0.05 ) (Human Body Model) TNPU0603: 1000 V TNPU0805: 1500 V TNPU1206: 2000 V Note (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. Revision: 01-Jul-16 7 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPU e3 www.vishay.com Vishay Draloric DIMENSIONS L Tt W H Tb DIMENSIONS AND MASS H L W T T MASS TYPE / SIZE t b (mm) (mm) (mm) (mm) (mm) (mg) TNPU0603 e3 0.45 ± 0.10 1.6 ± 0.10 0.85 ± 0.10 0.3 ± 0.20 0.3 ± 0.20 2 TNPU0805 e3 0.45 ± 0.10 2.0 ± 0.15 1.25 ± 0.15 0.4 ± 0.20 0.4 ± 0.20 5.5 TNPU1206 e3 0.55 ± 0.10 3.2 ± 0.15 1.6 ± 0.15 0.5 ± 0.25 0.5 ± 0.25 10 SOLDER PAD DIMENSIONS G X Y RECOMMENDED SOLDER PAD DIMENSIONS REFLOW SOLDERING WAVE SOLDERING TYPE / SIZE Y X G Y X G (mm) (mm) (mm) (mm) (mm) (mm) TNPU0603 e3 0.5 0.9 1.0 0.9 0.9 1.0 TNPU0805 e3 0.7 1.3 1.2 0.9 1.3 1.3 TNPU1206 e3 0.9 1.7 2.0 1.1 1.7 2.3 Revision: 01-Jul-16 8 Document Number: 28779 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: V ishay: TNPU0603100KAZEN00 TNPU0603100RAZEN00 TNPU060310K0AZEN00 TNPU06031K00AZEN00 TNPU060349K9AZEN00 TNPU06034K99AZEN00 TNPU0805100KAZEN00 TNPU0805100RAZEN00 TNPU080510K0AZEN00 TNPU08051K00AZEN00 TNPU1206100KAZEN00 TNPU1206100RAZEN00 TNPU120610K0AZEN00 TNPU12061K00AZEN00 TNPU08054K99AZEN00 TNPU080549K9AZEN00 TNPU0603100KBZEN00 TNPU0603100RBZEN00 TNPU060310K0BZEN00 TNPU060315K0BZEN00 TNPU06031K00BZEN00 TNPU060320K0BZEN00 TNPU060324K9BZEN00 TNPU06032K00BZEN00 TNPU06032K49BZEN00 TNPU060349K9BZEN00 TNPU06034K99BZEN00 TNPU0805100KBZEN00 TNPU0805100RBZEN00 TNPU080510K0BZEN00 TNPU08051K00BZEN00 TNPU080520K0BZEN00 TNPU08052K00BZEN00 TNPU080549K9BZEN00 TNPU08054K99BZEN00 TNPU1206100KBZEN00 TNPU1206100RBZEN00 TNPU120610K0BZEN00 TNPU12061K00BZEN00 TNPU120620K0BZEN00 TNPU12062K00BZEN00 TNPU120649K9BZEN00 TNPU12064K99BZEN00 TNPU0603102KBZEA00 TNPU060399R8BZEA00 TNPU0805333KAYEA00 TNPU080599R8AYEA00 TNPU1206512KBZEA00 TNPU120699R8BZEA00 TNPU060351K1BZEN00