Chip tantalum capacitors TC Series P Case Datasheet Features 1) Small package, large capacitance chip tantalum capacitor. 2) Low impedance capacitors. 3) Screening by thermal shock. Dimensions Anode mark (Unit : mm) Dimensions Size L 2.0 ± 0.2 L W1 W1 1.25 ± 0.2 H W2 0.9 ± 0.2 H 1.2 Max. W2 S 0.45 ± 0.3 S S + − Part No. Explanation TT C P 1 A 1 0 5 M 8 R 1 2 3 4 5 6 1 Series name 4 Nominal capacitance TC Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. 2 Case style P : 2012-12 (0805) size 5 Capacitance tolerance M : ± 20% 3 Rated voltage 6 Taping Rated voltage (V) 4 6.3 10 16 20 25 CODE 0G 0J 1A 1C 1D 1E 8 : Reel width : 8mm R : Positive electrode on the side opposite to sprocket hole www.rohm.com 1/6 ○c 2013 ROHM Co., Ltd. All rights reserved. 2013.11 - Rev.I

TC Series P Case Datasheet Rated table Rated voltage (V.DC) Capacitance (μF) 4 6.3 10 16 25 1.0 (105) P P P 1.5 (155) P 2.2 (225) P P 3.3 (335) P 4.7 (475) P P 10 (106) P P P 15 (156) P 22 (226) P P Remark) Case size codes (P) in the above show products line-up. Marking The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : A voltage code is shown as below table. (3) Capacitance : A capacitance code is shown as below table. Voltage Rated DC Capacitance Nominal Code Voltage (V) Code Capacitance (μF) g 4 A 1.0 j 6.3 E 1.5 A 10 J 2.2 C 16 N 3.3 D 20 S 4.7 E 25 a 10 e 15 j 22 Visual typical example voltage code and capacitance code are variable with parts number. [P case] j J EX.) − − (1) (2) (1) voltage code (2) capacitance code jj JJ manufacture code www.rohm.com 2/6 ○c 2013 ROHM Co., Ltd. All rights reserved. 2013.11 - Rev.I

TC Series P Case Datasheet Characteristics Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Operating Temperature −55°C to +125°C Voltage reduction when temperature exceeds +85°C Maximum operating +85°C temperature with no voltage derating Rated voltage (V.DC) 4 6.3 10 16 20 25 at 85°C Category voltage (V.DC) 2.5 4 6.3 10 13 16 at 125°C Surge voltage (V.DC) 5.0 8 13 20 26 32 at 85°C DC Leakage current Shall be satisfied the value on As per 4.9 JIS C 5101-1 " Standard list " As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1min Capacitance tolerance Shall be satisfied allowance range. As per 4.7 JIS C 5101-1 ±20% As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5V.DC Measuring circuit : DC Equivalent series circuit Tangent of loss angle Shall be satisfied the value on As per 4.8 JIS C 5101-1 (Df, tan δ) " Standard list " As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5V.DC Measuring circuit : DC Equivalent series circuit Impedance Shall be satisfied the value on As per 4.10 JIS C 5101-1 " Standard list " As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Resistance to Appearance There should be no significant abnormality. As per 4.14 JIS C 5101-1 Soldering heat The indications should be clear. As per 4.6 JIS C 5101-3 Dip in the solder bath L.C. Less than initial limit Solder temp : 260±10°C C / C TCP0J226M8R : Within ±20% of initial value Duration : 5±0.5s TCP1A106M8R : Within ±20% of initial value Repetition : 1 Others : Within ±10% of initial value After the specimens, leave it at room temperature for over 24h and then measure the sample. Df (tan δ) Less than 150% of initial limit Temperature Appearance There should be no significant abnormality. As per 4.16 JIS C 5101-1 cycle The indications should be clear. As per 4.10 JIS C 5101-3 Repetition : 5 cycles L.C. TCP0J226M8R : Less than 150% of initial limit (1 cycle : steps 1 to 4) without discontinuation. Others : Less than initial limit Temp. Time C / C 1 to 10μF : Within ±10% of initial value 1 −55±3°C 30±3min. 15 to 33μF : Within ±20% of initial value 2 Room temp. 3min.or less TCP1A106M8R : Within ±20% of initial value 3 125±2°C 30±3min. Df (tan δ) Less than 150% of initial limit 4 Room temp. 3min.or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Moisture Appearance There should be no significant abnormality. As per 4.22 JIS C 5101-1 resistance The indications should be clear. As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric L.C. TCP0G336M8R : Less than 150% of initial limit condition that the temperature and humidity are Others : Less than initial limit 60±2°C and 90 to 95% RH,respectiveiy, for 500±12h C / C Within ±20% of initial value leave it at room temperature for over 24h and then measure the Df (tan δ) Less than 150% of initial limit sample. www.rohm.com 3/6 ○c 2013 ROHM Co., Ltd. All rights reserved. 2013.11 - Rev.I

TC Series P Case Datasheet Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101− 3) Temperature Temp. −55°C As per 4.29 JIS C 5101-1 Stability As per 4.13 JIS C 5101-3 C / C Within 0/−15% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " L.C. − Temp. +85°C C / C Within +15/0% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " L.C. Less than 1000% of initial limit Temp. +125°C C / C Within +20/0% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " L.C. Less than 1250% of initial limit Surge voltage Appearance There should be no significant abnormality. As per 4.26JIS C 5101-1 As per 4.14JIS C 5101-3 L.C. Shall be satisfied the voltage on " Standard list " Apply the specified surge voltage via the serial resistance of 1kΩ every 5±0.5 min. C / C TOCthPe0rsJ 2 2 6 M 8 R :: WWiitthhiinn ±±2100%% ooff iinniittiiaall vvaalluuee for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for Df (tan δ) Less than 150% of initial limit over 24h and then measure the sample. Loading at Appearance There should be no significant abnormality. As per 4.23 JIS C 5101-1 High temperature As per 4.15 JIS C 5101-3 L.C. TCP0J226M8R : Less than 150% of initial limit After applying the rated voltage for 1000+36/0 h without Others : Less than initial limit discontinuation via the serial resistance of 3Ω or less C / C TCP0J226M8R : Within ±20% of initial value at a temperature of 85±2°C, leave the sample at room Others : Within ±10% of initial value temperature / humidity for over 24h and measure the value. Df (tan δ) Less than 150% of initial limit Terminal Capacitance The measured value should be stable. As per 4.35 JIS C 5101-1 strength As per 4.9 JIS C 5101-3 Appearance There should be no significant abnormality. A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below) (Unit : mm) 20 50 F (Apply force) R230 1 thickness=1.6mm 45 45 Adhesiveness The terminal should not come off. As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product Apply force a circuit board www.rohm.com 4/6 ○c 2013 ROHM Co., Ltd. All rights reserved. 2013.11 - Rev.I

TC Series P Case Datasheet Item Performance Test conditions (JIS C 5101−1 and JIS C 5101− 3) Dimensions Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. Solderability 3/4 or more surface area of the solder coated As per 4.15.2 JIS C 5101-1 terminal dipped in the soldering bath should As per 4.7 JIS C 5101-3 be covered with the new solder. Dip speed=25±2.5mm / s Pre−treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25% IPA 75% Vibration Capacitance Measure value should not fluctuate during As per 4.17 JIS C 5101-1 the measurement. Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Appearance There should be no significant abnormality. Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Standard products list Df Rated Category Surge Cap. Tolerance Leakage Impedance 120Hz voltage voltage voltage 120Hz current 100kHz (%) Part No. 85°C 125°C 85°C 25°C 1WV.60s (V) (V) (V) (μF) (%) (μA) −55°C 2855°°CC 125°C (Ω) TC P 0G 106 M8R 4 2.5 5 10 ± 20 0.5 30 20 30 9.3 TC P 0G 226 M8R 4 2.5 5 22 ± 20 0.9 30 20 30 7.7 TC P 0J 225 M8R 6.3 4 8 2.2 ± 20 0.5 30 20 30 17.5 TC P 0J 475 M8R 6.3 4 8 4.7 ± 20 0.5 30 20 30 11.8 TC P 0J 106 M8R 6.3 4 8 10 ± 20 0.6 30 20 30 8.3 TC P 0J 156 M8R 6.3 4 8 15 ± 20 0.9 30 20 30 7.7 TC P 0J 226 M8R 6.3 4 8 22 ± 20 1.4 38 25 38 5.0 TC P 1A 105 M8R 10 6.3 13 1.0 ± 20 0.5 15 10 15 17.5 TC P 1A 155 M8R 10 6.3 13 1.5 ± 20 0.5 30 20 30 16.1 TC P 1A 225 M8R 10 6.3 13 2.2 ± 20 0.5 30 20 30 14.4 TC P 1A 335 M8R 10 6.3 13 3.3 ± 20 0.5 30 20 30 11.8 TC P 1A 475 M8R 10 6.3 13 4.7 ± 20 0.5 30 20 30 9.3 TC P 1A 106 M8R 10 6.3 13 10 ± 20 1.0 30 20 30 7.7 TC P 1C 105 M8R 16 10 20 1.0 ± 20 0.5 15 10 15 16.1 TC P 1E 105 M8R 25 16 32 1.0 ± 20 0.6 30 20 30 9.3 www.rohm.com 5/6 ○c 2013 ROHM Co., Ltd. All rights reserved. 2013.11 - Rev.I

TC Series P Case Datasheet Packaging specifications Sprocket hole φD0 t1 E A F B W t2 P1 P2 P0 Pull-out direction Component is loaded (Unit : mm) A B W E F P1 P2 P0 D0 t1 t2 standard packaging quantity 1.55±0.1 2.3±0.1 8.0±0.2 1.75±0.1 3.5±0.05 4.0±0.1 2.0±0.05 4.0±0.1 φ1.55±0.05 0.25±0.05 1.32±0.1 3000pcs Reel dimensions 0 1.0 +0 11.4±1.0 9. 2 0. ± 3 1 φ 5 1.00 0−1. + 0 80 6 1 φ φ Label Pull-out direction (Unit : mm) EIAJ ET−7200A www.rohm.com 6/6 ○c 2013 ROHM Co., Ltd. All rights reserved. 2013.11 - Rev.I

DDaattaasshheeeett Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved.

DDaattaasshheeeett Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved.

DDaattaasshheeeett General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sale s representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE Rev.001 © 2015 ROHM Co., Ltd. All rights reserved.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: R OHM Semiconductor: TCP0J475M8R TCP1A105M8R TCP1A475M8R TCP1A106M8R TCP0J225M8R TCP1C105M8R TCP0G106M8R TCP0J156M8R TCP0G226M8R TCP1A225M8R TCP1E105M8R TCP0J226M8R TCP0J106M8R