SURFACE MOUNT LED LAMPS Standard Type Chip LEDs with reflector SML-010 Series Pure Green Green Yellow Orange Red Package Size(cid:0) GaP GaAsP on GaP GaAlAs on GaAs （mm）(cid:0) 555nm 570nm 585nm 610nm 650nm 660nm 3216 (1206) 3.0x2.0 t=1.3 SML-010PT SML-010MT SML-010YT SML-010DT SML-010VT SML-010LT ■ Absolute Maximum Ratings（Ta=25℃）(cid:0) ■External Dimensions（Unit：mm）(cid:0) Power(cid:0) Forward(cid:0) Peak(cid:0)Reverse(cid:0)Operating(cid:0) Stotage(cid:0) 3.0 1.3＋−00..12 Emitting(cid:0)dissipation current(cid:0)forward(cid:0)voltage temperature temperature(cid:0) 2.3 0.3 0.5 Part No. current(cid:0) color （mPWD）(cid:0)（mIFA）(cid:0) ＊IFP （VVR）(cid:0) （T°oCp）r (cid:0) （T°sCtg）(cid:0) （mA）(cid:0) 0 6 2. 1. SML-010PT Pure Green SML-010MT Green Cathode mark SML-010YT Yellow 70 25 60 4 -30 to +85 -40 to +85 SML-010DT Orange SML-010VT Red SML-010LT Red 75 30 75 2-Ｒ0.3 ＊IFP measured under duty ≦1/ 5,pulse width ≦1ms. 7 1. ■ Electrical Optical Characteristics（Ta=25℃）(cid:0) Terminal 1.6 Forward(cid:0) Reverse(cid:0) Light wavelength Brightness(cid:0) Tolerance:±0.1 voltage(cid:0) current(cid:0) Peak Half-wave IV Part No. Resin Color VF IR λp ∆λ ■Directivity Typ. IF Max. VR Typ. Typ. IF Min. Typ. IF (V) (mA) (µA) (V) (nm) (nm) (mA) (mcd) (mcd) (mA) SML-010PT 555 2.2 6.3 X’ Y’ 0° 2.2 30° 30° SML-010MT 570 5.6 25 SML-010YT Transparent(cid:0)2.1 585 40 2.2 6.3 SML-010DT Clear 20 100 4 610 20 3.6 10 20 60° 60° 2.0 SML-010VT 650 2.2 6.3 SML-010LT 1.75 660 25 5.6 16 90° 90° 100 50 0 50 100 Relative brightness (%) (Typ.) ■ Recommemded Pad Layout ■ Packaging Spacifications（Unit：mm）(cid:0) Tape Spacifications：T86〈2,500pcs／reel〉 Reel Spacifications 1.6 L 5 a 1.4 4 Feeding direction vel Po 1.5 2 φ1.5 1.75 sition 5 5 3.8 1.4 3.4 5.5 φ13 2.4 0.5 1.6 （Unit：mm）(cid:0) φ60 1.4 1 The recommended thickness of the screen mask φ180 for soldering is between 100 and 200μm. The hole size of the screen mask should be same as the recommended land pattern or smaller.

SURFACE MOUNT LED LAMPS ■ Electrical Characteristic Curves Forward Current - Forward Voltage Relative Luminous Intensity - Case Temperature 50 SML-010PT(cid:0) 1.6 SML-010PT(cid:0) Ta=25℃(cid:0) SML-010MT(cid:0) Y IF=20mA SML-010MT(cid:0) mA()NT : I F 521.000 SSMMLL--001100YDTT(cid:0)(cid:0) S INTENSIT 11..42 SSMMLL--001100YDTT(cid:0)(cid:0) E SML-010VT(cid:0) U SML-010VT(cid:0) CURR 2.0 SML-010LT MINO 1.0 SML-010LT D 1.0 LU FORWAR 00..52 ELATIVE 00..86 R 0.1 0.4 1.5 2.0 2.5 3.0 −20 0 20 40 60 80 FORWARD VOLTAGE : VF (V) CASE TEMPERATURE : Tc (℃) Relative Luminous Intensity - Forward Current 3.0 SML-010PT(cid:0) 3.0 SML-010LT TY f=1kHz SML-010MT(cid:0) TY f=1kHz SI 2.5 SI 2.5 N SML-010YT(cid:0) N S INTE 2.0 DC SML-010DT(cid:0) S INTE 2.0 DC U SML-010VT U O O N 1.5 DF=50% N 1.5 MI MI DF=50% U U L L E 1.0 E 1.0 TIV 20% TIV 20% ELA 0.5 15% ELA 0.5 15% R 10% R 10% 0 5% 0 5% 0 10 20 30 40 50 60 0 10 20 30 40 50 60 PEAK FORWARD CURRENT : IF peak (mA) PEAK FORWARD CURRENT : IF peak (mA) Ratio of Maximum Tolerable Peak Current - Pulse Duration (cid:0) (cid:0) I(cid:0)ax. peak FMIax. FM 56 SSMMLL--001100PMTT(cid:0)(cid:0) I(cid:0)ax. peak FMIax. FM 56 SML-010LT RATIO of MAXIMUM TOLERABLE PEAK CURRENTto MAXIMUM TOLERABLE DC CURRENT 2.441235 150kHz0 220kHz0 510kHz0 15kHz02 2kHz 1kHz 1500Hz03200Hz 100Hz 104 SSSMMMLLL---000111000YDVTTT(cid:0)(cid:0) RATIO of MAXIMUM TOLERABLE PEAK CURRENTto MAXIMUM TOLERABLE DC CURRENT 2.541235 10 20 510kHz0 15kHz02 2kHz 1kHz 1500Hz03200Hz 100Hz 104 PULSE DURATION : Tw (μs) PULSE DURATION : Tw (μs) Derating A) m SML-010PT(cid:0) (T : I ax. FM 30 SSMMLL--001100MYTT(cid:0)(cid:0) N E SML-010DT(cid:0) R UR 20 SML-010VT(cid:0) D C (cid:0) SML-010LT R A W (cid:0) OR 10 F M (cid:0) U M AXI 0 M 0 10 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE : Ta (℃)

Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: R OHM Semiconductor: SML-010FTT86 SML-010LTT86 SML-010MTT87