PIC24FJ256GA110 Family Data Sheet 64/80/100-Pin, 16-Bit, General Purpose Flash Microcontrollers with Peripheral Pin Select  2010 Microchip Technology Inc. DS39905E

Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device Trademarks applications and the like is provided only for your convenience The Microchip name and logo, the Microchip logo, dsPIC, and may be superseded by updates. It is your responsibility to KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, ensure that your application meets with your specifications. PIC32 logo, rfPIC and UNI/O are registered trademarks of MICROCHIP MAKES NO REPRESENTATIONS OR Microchip Technology Incorporated in the U.S.A. and other WARRANTIES OF ANY KIND WHETHER EXPRESS OR countries. IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, INCLUDING BUT NOT LIMITED TO ITS CONDITION, MXDEV, MXLAB, SEEVAL and The Embedded Control QUALITY, PERFORMANCE, MERCHANTABILITY OR Solutions Company are registered trademarks of Microchip FITNESS FOR PURPOSE. Microchip disclaims all liability Technology Incorporated in the U.S.A. arising from this information and its use. Use of Microchip Analog-for-the-Digital Age, Application Maestro, CodeGuard, devices in life support and/or safety applications is entirely at dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, the buyer’s risk, and the buyer agrees to defend, indemnify and ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial hold harmless Microchip from any and all damages, claims, Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified suits, or expenses resulting from such use. No licenses are logo, MPLIB, MPLINK, mTouch, Omniscient Code conveyed, implicitly or otherwise, under any Microchip Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, intellectual property rights. PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2010, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-60932-670-8 Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS39905E-page 2  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 64/80/100-Pin, 16-Bit, General Purpose Flash Microcontrollers with Peripheral Pin Select Power Management: Peripheral Features: • On-Chip 2.5V Voltage Regulator • Peripheral Pin Select: • Switch between Clock Sources in Real Time - Allows independent I/O mapping of many • Idle, Sleep and Doze modes with Fast Wake-up and peripherals at run time Two-Speed Start-up - Continuous hardware integrity checking and safety • Run mode: 1 mA/MIPS, 2.0V Typical interlocks prevent unintentional configuration changes • Standby Current with 32 kHz Oscillator: 2.6 A, - Up to 46 available pins (100-pin devices) 2.0V Typical • Three 3-Wire/4-Wire SPI modules (supports 4 Frame modes) with 8-Level FIFO Buffer High-Performance CPU: • Three I2C™ modules support Multi-Master/Slave modes • Modified Harvard Architecture and 7-Bit/10-Bit Addressing • Up to 16MIPS Operation at 32MHz • Four UART modules: • 8 MHz Internal Oscillator - Supports RS-485, RS-232, LIN/J2602 protocols • 17-Bit x 17-Bit Single-Cycle Hardware Multiplier and IrDA® • 32-Bit by 16-Bit Hardware Divider - On-chip hardware encoder/decoder for IrDA • 16 x 16-Bit Working Register Array - Auto-wake-up and Auto-Baud Detect (ABD) • C Compiler Optimized Instruction Set Architecture with - 4-level deep FIFO buffer Flexible Addressing modes • Five 16-Bit Timers/Counters with Programmable Prescaler • Linear Program Memory Addressing, Up to 12Mbytes • Nine 16-Bit Capture Inputs, each with a • Linear Data Memory Addressing, Up to 64Kbytes Dedicated Time Base • Two Address Generation Units for Separate Read and • Nine 16-Bit Compare/PWM Outputs, each with a Write Addressing of Data Memory Dedicated Time Base Analog Features: • 8-Bit Parallel Master Port (PMP/PSP): - Up to 16 address pins • 10-Bit, Up to 16-Channel Analog-to-Digital (A/D) - Programmable polarity on control lines Converter at 500ksps: • Hardware Real-Time Clock/Calendar (RTCC): - Conversions available in Sleep mode - Provides clock, calendar and alarm functions • Three Analog Comparators with Programmable Input/ • Programmable Cyclic Redundancy Check (CRC) Generator Output Configuration • Up to 5 External Interrupt Sources • Charge Time Measurement Unit (CTMU) Remappable Peripherals PDICev2i4cFeJ Pins ProgramMemory (Bytes) SRAM (Bytes) RemappablePins Timers 16-Bit Capture Input Compare/PWM Output ®UART w/ IrDA SPI 2IC™ 10-Bit A/D (ch) Comparators PMP/PSP JTAG CTMU 64GA106 64 64K 16K 31 5 9 9 4 3 3 16 3 Y Y Y 128GA106 64 128K 16K 31 5 9 9 4 3 3 16 3 Y Y Y 192GA106 64 192K 16K 31 5 9 9 4 3 3 16 3 Y Y Y 256GA106 64 256K 16K 31 5 9 9 4 3 3 16 3 Y Y Y 64GA108 80 64K 16K 42 5 9 9 4 3 3 16 3 Y Y Y 128GA108 80 128K 16K 42 5 9 9 4 3 3 16 3 Y Y Y 192GA108 80 192K 16K 42 5 9 9 4 3 3 16 3 Y Y Y 256GA108 80 256K 16K 42 5 9 9 4 3 3 16 3 Y Y Y 64GA110 100 64K 16K 46 5 9 9 4 3 3 16 3 Y Y Y 128GA110 100 128K 16K 46 5 9 9 4 3 3 16 3 Y Y Y 192GA110 100 192K 16K 46 5 9 9 4 3 3 16 3 Y Y Y 256GA110 100 256K 16K 46 5 9 9 4 3 3 16 3 Y Y Y  2010 Microchip Technology Inc. DS39905E-page 3

PIC24FJ256GA110 FAMILY Special Microcontroller Features: • Power-on Reset (POR), Power-up Timer (PWRT), Low-Voltage Detect (LVD) and Oscillator Start-up Timer • Operating Voltage Range of 2.0V to 3.6V (OST) • Self-Reprogrammable under Software Control • Flexible Watchdog Timer (WDT) with On-Chip • 5.5V Tolerant Input (digital pins only) Low-Power RC Oscillator for Reliable Operation • Configurable Open-Drain Outputs on Digital I/O • In-Circuit Serial Programming™ (ICSP™) and • High-Current Sink/Source (18mA/18mA) on all I/O In-Circuit Debug (ICD) via 2 Pins • Selectable Power Management modes: • JTAG Boundary Scan Support - Sleep, Idle and Doze modes with fast wake-up • Brown-out Reset (BOR) • Fail-Safe Clock Monitor Operation: • Flash Program Memory: - Detects clock failure and switches to on-chip - 10,000 erase/write cycle endurance (minimum) FRC oscillator - 20-year data retention minimum • On-Chip LDO Regulator - Selectable write protection boundary - Write protection option for Flash Configuration Words Pin Diagram (64-Pin TQFP and QFN(1)) N62/PMD4/RE4 N61/PMD3/RE3 N60/PMD2/RE2N59/PMD1/RE1N58/PMD0/RE0N69/RF1 N68/RF0 NVREG /VCAPDDCORE3INA/CN16/RD7 3INB/CN15/RD6P20/CN14/PMRD/RD5 P25/CN13/PMWR/RD4 P22/CN52/PMBE/RD3P23/CN51/RD2P24/CN50/RD1 C C CCCC C E VC CR R RRR 4 3 2 1 0 98 7 6 5 4 3 2 1 0 9 6 6 6 6 6 55 5 5 5 5 5 5 5 5 4 CN63/PMD5/RE5 1 48 SOSCO/C3INC/RPI37/T1CK/CN0/RC14 SCL3/CN64/PMD6/RE6 2 47 SOSCI/C3IND/CN1/RC13 SDA3/CN65/PMD7/RE7 3 46 RP11/CN49/RD0 PMA5/RP21/C1IND/CN8/RG6 4 45 RP12/CN56/PMCS1/RD11 C1INC/RP26/CN9/PMA4/RG7 5 PIC24FJ64GA106 44 RP3/CN55/PMCS2/RD10 C2IND/RP19/CN10/PMA3/RG8 6 43 RP4/CN54/RD9 MCLR 7 PIC24FJ128GA106 42 RTCC/RP2/CN53/RD8 C2INC/RP27/CN11/PMA2/RG9 8 PIC24FJ192GA106 41 VSS VSS 9 40 OSCO/CLKO/CN22/RC15 VDD 10 PIC24FJ256GA106 39 OSCI/CLKI/CN23/RC12 PGEC3/AN5/C1INA/RP18/CN7/RB5 11 38 VDD PGED3/AN4/C1INB/RP28/CN6/RB4 12 37 SCL1/CN83/RG2 AN3/C2INA/CN5/RB3 13 36 SDA1/CN84/RG3 AN2/C2INB/RP13/CN4/RB2 14 35 ASCK1/RPI45/INT0/CN72/RF6 PGEC1/AN1/VREF-/RP1/CN3/RB1 15 34 RP30/CN70/RF2 PGED1/AN0/VREF+/RP0/CN2/PMA6/RB0 16 33 RP16/CN71/RF3 7 8 9 0 12 3 4 5 6 7 8 9 0 1 2 1 1 1 2 22 2 2 2 2 2 2 2 3 3 3 PGEC2/AN6/RP6/CN24/RB6 PGED2/AN7/RP7/CN25/RB7 AVDD AVSSAN8/RP8/CN26/RB8 AN9/RP9/CN27/PMA7/RB9 TMS/AN10/CV/CN28/PMA13/RB10REF TDO/AN11/CN29/PMA12/RB11VSS VDD TCK/AN12/CTED2/CN30/PMA11/RB12 TDI/PMA10/AN13/CTED1/CN31/RB13 AN14/CTPLS/RP14/CN32/PMA1/RB14 AN15/REFO/RP29/CN12/PMA0/RB15 SDA2/RP10/CN17/PMA9/RF4 SCL2/RP17/CN18/PMA8/RF5 Legend: Shaded pins indicate pins tolerant to up to +5.5VDC. RPn represents remappable pins for Peripheral Pin Select (PPS) feature. Note 1: For QFN devices, the backplane on the underside of the device must also be connected to VSS. DS39905E-page 4  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY Pin Diagram (80-Pin TQFP) N62/PMD4/RE4N61/PMD3/RE3 N60/PMD2/RE2 N59/PMD1/RE1N58/PMD0/RE0N77/RG0N78/RG1N69/RF1N68/RF0 NVREG /VCAPDDCORE3INA/CN16/RD73INB/CN15/RD6 P20/CN14/PMRD/RD5P25/CN13/PMWR/RD4N19/RD13PI42/CN57/RD12 P22/CN52/PMBE/RD3P23/CN51/RD2P24/CN50/RD1 CC C CCCCCC E VCC RRCR RRR 8079787776 75747372717069686766 6564636261 CN63/PMD5/RE5 1 60 SROPIS3C7/OT/1CC3KIN/CCN/0/RC14 SCL3/CN64/PMD6/RE6 2 59 SOSCI/C3IND/CN1/RC13 SDA3/CN65/PMD7/RE7 3 58 RP11/CN49/RD0 RPI38/CN45/RC1 4 57 RP12/CN56/PMCS1/RD11 RPI40/CN47/RC3 5 56 RP3/CN55/PMCS2/RD10 C1IND/RP21/CN8/PMA5/RG6 6 55 RP4/CN54/RD9 C1INC/RP26/CN9/PMA4/RG7 7 PIC24FJ64GA108 54 RTCC/RP2/CN53/RD8 C2IND/RP19/CN10/PMA3/RG8 8 53 SDA2/RPI35/CN44/RA15 MCLR 9 PIC24FJ128GA108 52 SCL2/RPI36/CN43/RA14 C2INC/RP27/CN11/PMA2/RG9 10 PIC24FJ192GA108 51 VSS VSS 11 50 OSCO/CLKO/CN22/RC15 VDD 12 PIC24FJ256GA108 49 OSCI/CLKI/CN23/RC12 TMS/RPI33/CN66/RE8 13 48 VDD TDO/RPI34/CN67/RE9 14 47 SCL1/CN83/RG2 PGEC3/AN5/C1INA/CN7/RP18/RB5 15 46 SDA1/CN84/RG3 PGED3/AN4/C1INB/RP28/CN6/RB4 16 45 ASCK1/RPI45/INT0/CN72/RF6 AN3/C2INA/CN5/RB3 17 44 RPI44/CN73/RF7 AN2/C2INB/RP13/CN4/RB2 18 43 RP15/CN74/RF8 PGEC1/AN1/RP1/CN3/RB1 19 42 RP30/CN70/RF2 PGED1/AN0/RP0/CN2/RB0 20 41 RP16/CN71/RF3 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 RB6 RB7 RA9 A10 VDD VSSRB8 RB9 B10 B11Vss VDD B12 B13 B14 B15D14 D15 RF4 RF5 PGEC2/AN6/RP6/CN24/ PGED2/RP7/AN7/CN25/ PMA7/-/CN41/VREF PMA6/V+/CN42/RREF A ARP8/AN8/CN26/ RP9/AN9/CN27/ PMA13/AN10/CV/CN28/RREF PMA12/AN11/CN29/R TCK/AN12/CTED2/CN30/PMA11/R TDI/AN13/CTED1/CN31/PMA10/R AN14/CTPLS/RP14/CN32/PMA1/R AN15/REFO/RP29/CN12/PMA0/RRPI43/CN20/R RP5/CN21/R RP10/CN17/PMA9/ RP17/CN18/PMA8/ Legend: Shaded pins indicate pins tolerant to up to +5.5VDC. RPn represents remappable pins for Peripheral Pin Select (PPS) feature.  2010 Microchip Technology Inc. DS39905E-page 5

PIC24FJ256GA110 FAMILY Pin Diagram (100-Pin TQFP) CN62/PMD4/RE4CN61/PMD3/RE3CN60/PMD2/RE2CN80/RG13CN79/RG12CN81/RG14CN59/PMD1/RE1CN58/PMD0/RE0CN40/RA7CN39/RA6CN77/RG0CN78/RG1CN69/RF1CN68/RF0ENVREGV/VCAPDDCOREC3INA/CN16/RD7C3INB/CN15/RD6RP20/CN14/PMRD/RD5RP25/CN13/PMWR/RD4CN19/RD13RPI42/CN57/RD12RP22/CN52/PMBE/RD3RP23/CN51/RD2RP24/CN50/RD1 CN82/RG15 1 100999897969594939291908988878685848382818079787776 75 VSS SOSCO/C3INC/ VDD 2 74 RPI37/T1CK/CN0/RC14 CN63/PMD5/RE5 3 73 SOSCI/C3IND/CN1/RC13 SCL3/CN64/PMD6/RE6 4 72 RP11/CN49/RD0 SDA3/CN65/PMD7/RE7 5 71 RP12/CN56/PMCS1/RD11 RPI38/CN45/RC1 6 70 RP3/CN55/PMCS2/RD10 RPI39/CN46/RC2 7 69 RP4/CN54/RD9 RPI40/CN47/RC3 8 68 RTCC/RP2/CN53/RD8 RPI41/CN48/RC4 9 PIC24FJ64GA110 67 ASDA2/RPI35/CN44/RA15 C1IND/RP21/CN8/PMA5/RG6 10 66 ASCL2/RPI36/CN43/RA14 C1INC/RP26/CN9/PMA4/RG7 11 PIC24FJ128GA110 65 VSS C2IND/RP19/CN10/PMA3/RG8 12 64 OSCO/CLKO/CN22/RC15 MCLR 13 PIC24FJ192GA110 63 OSCI/CLKI/CN23/RC12 C2INC/RP27/CN11/PMA2/RG9 14 PIC24FJ256GA110 62 VDD VSS 15 61 TDO/CN38/RA5 VDD 16 60 TDI/CN37/RA4 TMS/CN33/RA0 17 59 SDA2/CN36/RA3 RPI33/CN66/RE8 18 58 SCL2/CN35/RA2 RPI34/CN67/RE9 19 57 SCL1/CN83/RG2 PGEC3/AN5/C1INA/RP18/CN7/RB5 20 56 SDA1/CN84/RG3 PGED3/AN4/C1INB/RP28/CN6/RB4 21 55 ASCK1/RPI45/INT0/CN72/RF6 AN3/C2INA/CN5/RB3 22 54 RPI44/CN73/RF7 AN2/C2INB/RP13/CN4/RB2 23 53 RP15/CN74/RF8 PGEC1/AN1/RP1/CN3/RB1 24 52 RP30/CN70/RF2 PGED1/AN0/RP0/CN2/RB0 25 51 RP16/CN71/RF3 6789012345678901234567890 2222333333333344444444445 PGEC2/AN6/RP6/CN24/RB6PGED2/AN7/RP7/CN25/RB7V-/CN41/PMA7/RA9REF PMA6/V+/CN42/RA10REF AVDD AVSS AN8/RP8/CN26/RB8AN9/RP9/CN27/RB9AN10/CV/CN28/PMA13/RB10REF AN11/CN29/PMA12/RB11VSS VDDTCK/CN34/RA1RP31/CN76/RF13RPI32/CN75/RF12AN12/CTED2/CN30/PMA11/RB12AN13/CTED1/CN31/PMA10/RB13AN14/CTPLS/RP14/CN32/PMA1/RB14AN15/REFO/RP29/CN12/PMA0/RB15 VSS VDD RPI43/CN20/RD14RP5/CN21/RD15RP10/CN17/PMA9/RF4RP17/CN18/PMA8/RF5 Legend: Shaded pins indicate pins tolerant to up to +5.5VDC. RPn represents remappable pins for Peripheral Pin Select (PPS) feature. DS39905E-page 6  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY Table of Contents 1.0 Device Overview..........................................................................................................................................................................9 2.0 Guidelines for Getting Started with 16-Bit Microcontrollers........................................................................................................23 3.0 CPU ...........................................................................................................................................................................................29 4.0 Memory Organization.................................................................................................................................................................35 5.0 Flash Program Memory..............................................................................................................................................................57 6.0 Resets........................................................................................................................................................................................65 7.0 Interrupt Controller.....................................................................................................................................................................71 8.0 Oscillator Configuration............................................................................................................................................................115 9.0 Power-Saving Features............................................................................................................................................................125 10.0 I/O Ports...................................................................................................................................................................................127 11.0 Timer1......................................................................................................................................................................................155 12.0 Timer2/3 and Timer4/5 ............................................................................................................................................................157 13.0 Input Capture with Dedicated Timer.........................................................................................................................................163 14.0 Output Compare with Dedicated Timer....................................................................................................................................167 15.0 Serial Peripheral Interface (SPI)...............................................................................................................................................175 16.0 Inter-Integrated Circuit (I2C™).................................................................................................................................................185 17.0 Universal Asynchronous Receiver Transmitter (UART)...........................................................................................................193 18.0 Parallel Master Port (PMP).......................................................................................................................................................201 19.0 Real-Time Clock and Calendar (RTCC) ..................................................................................................................................211 20.0 Programmable Cyclic Redundancy Check (CRC) Generator..................................................................................................221 21.0 10-Bit High-Speed A/D Converter............................................................................................................................................225 22.0 Triple Comparator Module........................................................................................................................................................235 23.0 Comparator Voltage Reference................................................................................................................................................239 24.0 Charge Time Measurement Unit (CTMU)................................................................................................................................241 25.0 Special Features......................................................................................................................................................................245 26.0 Instruction Set Summary..........................................................................................................................................................257 27.0 Development Support...............................................................................................................................................................265 28.0 Electrical Characteristics..........................................................................................................................................................269 29.0 Packaging Information..............................................................................................................................................................305 Appendix A: Revision History.............................................................................................................................................................319 Index................................................................................................................................................................................................. 321 The Microchip Web Site.....................................................................................................................................................................327 Customer Change Notification Service..............................................................................................................................................327 Customer Support..............................................................................................................................................................................327 Reader Response..............................................................................................................................................................................328 Product Identification System............................................................................................................................................................329  2010 Microchip Technology Inc. DS39905E-page 7

PIC24FJ256GA110 FAMILY TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. DS39905E-page 8  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 1.0 DEVICE OVERVIEW • Doze Mode Operation: When timing-sensitive applications, such as serial communications, This document contains device-specific information for require the uninterrupted operation of peripherals, the following devices: the CPU clock speed can be selectively reduced, allowing incremental power savings without • PIC24FJ64GA106 • PIC24FJ64GA110 missing a beat. • PIC24FJ128GA106 • PIC24FJ128GA110 • Instruction-Based Power-Saving Modes: The • PIC24FJ192GA106 • PIC24FJ192GA110 microcontroller can suspend all operations, or • PIC24FJ256GA106 • PIC24FJ256GA110 selectively shut down its core while leaving its peripherals active, with a single instruction in • PIC24FJ64GA108 software. • PIC24FJ128GA108 • PIC24FJ192GA108 1.1.3 OSCILLATOR OPTIONS AND • PIC24FJ256GA108 FEATURES All of the devices in the PIC24FJ256GA110 family offer This family expands on the existing line of Microchip‘s five different oscillator options, allowing users a range 16-bit general purpose microcontrollers, combining of choices in developing application hardware. These enhanced computational performance with an include: expanded and highly configurable peripheral feature set. The PIC24FJ256GA110 family provides a new • Two Crystal modes using crystals or ceramic platform for high-performance applications, which have resonators. outgrown their 8-bit platforms, but don’t require the • Two External Clock modes offering the option of a power of a digital signal processor. divide-by-2 clock output. • A Fast Internal Oscillator (FRC) with a nominal 1.1 Core Features 8MHz output, which can also be divided under software control to provide clock speeds as low as 1.1.1 16-BIT ARCHITECTURE 31kHz. Central to all PIC24F devices is the 16-bit modified • A Phase Lock Loop (PLL) frequency multiplier Harvard architecture, first introduced with Microchip’s available to the external oscillator modes and the dsPIC® digital signal controllers. The PIC24F CPU core FRC Oscillator, which allows clock speeds of up offers a wide range of enhancements, such as: to 32MHz. • 16-bit data and 24-bit address paths with the • A separate internal RC Oscillator (LPRC) with a ability to move information between data and fixed 31kHz output, which provides a low-power memory spaces option for timing-insensitive applications. • Linear addressing of up to 12Mbytes (program The internal oscillator block also provides a stable space) and 64Kbytes (data) reference source for the Fail-Safe Clock Monitor. This • A 16-element working register array with built-in option constantly monitors the main clock source software stack support against a reference signal provided by the internal • A 17 x 17 hardware multiplier with support for oscillator and enables the controller to switch to the integer math internal oscillator, allowing for continued low-speed operation or a safe application shutdown. • Hardware support for 32 by 16-bit division • An instruction set that supports multiple 1.1.4 EASY MIGRATION addressing modes and is optimized for high-level languages, such as ‘C’ Regardless of the memory size, all devices share the same rich set of peripherals, allowing for a smooth • Operational performance up to 16 MIPS migration path as applications grow and evolve. The 1.1.2 POWER-SAVING TECHNOLOGY consistent pinout scheme used throughout the entire family also aids in migrating from one device to the next All of the devices in the PIC24FJ256GA110 family larger, or even in jumping from 64-pin to 100-pin incorporate a range of features that can significantly devices. reduce power consumption during operation. Key The PIC24F family is pin-compatible with devices in the items include: dsPIC33 and PIC32 families, and shares some • On-the-Fly Clock Switching: The device clock compatibility with the pinout schema for PIC18 and can be changed under software control to the dsPIC30 devices. This extends the ability of applica- Timer1 source or the internal, low-power RC tions to grow from the relatively simple, to the powerful Oscillator during operation, allowing the user to and complex, yet still selecting a Microchip device. incorporate power-saving ideas into their software designs.  2010 Microchip Technology Inc. DS39905E-page 9

PIC24FJ256GA110 FAMILY 1.2 Other Special Features 1.3 Details on Individual Family Members • Peripheral Pin Select: The Peripheral Pin Select (PPS) feature allows most digital peripherals to be Devices in the PIC24FJ256GA110 family are available mapped over a fixed set of digital I/O pins. Users in 64-pin, 80-pin and 100-pin packages. The general may independently map the input and/or output of block diagram for all devices is shown in Figure1-1. any one of the many digital peripherals to any one The devices are differentiated from each other in four of the I/O pins. ways: • Communications: The PIC24FJ256GA110 family incorporates a range of serial communication 1. Flash program memory (64 Kbytes for PIC24FJ64GA1 devices, 128 Kbytes for peripherals to handle a range of application requirements. There are three independent I2C™ PIC24FJ128GA1 devices, 192 Kbytes for modules that support both Master and Slave PIC24FJ192GA1 devices and 256 Kbytes for modes of operation. Devices also have, through PIC24FJ256GA1 devices). the Peripheral Pin Select (PPS) feature, four 2. Available I/O pins and ports (53 pins on 6 ports independent UARTs with built-in IrDA® for 64-pin devices, 69 pins on 7 ports for 80-pin encoder/decoders and three SPI modules. devices and 85 pins on 7 ports for 100-pin • Analog Features: All members of the devices). PIC24FJ256GA110 family include a 10-bit A/D 3. Available Interrupt-on-Change Notification (ICN) Converter module and a triple comparator inputs (same as the number of available I/O pins module. The A/D module incorporates program- for all devices). mable acquisition time, allowing for a channel to 4. Available remappable pins (31 pins on 64-pin be selected and a conversion to be initiated with- devices, 42 pins on 80-pin devices and 46 pins out waiting for a sampling period, as well as faster on 100-pin devices) sampling speeds. The comparator module All other features for devices in this family are identical. includes three analog comparators that are These are summarized in Table1-1. configurable for a wide range of operations. A list of the pin features available on the • CTMU Interface: In addition to their other analog PIC24FJ256GA110 family devices, sorted by function, features, members of the PIC24FJ256GA110 is shown in Table1-4. Note that this table shows the pin family include the brand new CTMU interface location of individual peripheral features and not how module. This provides a convenient method for they are multiplexed on the same pin. This information precision time measurement and pulse genera- is provided in the pinout diagrams in the beginning of tion, and can serve as an interface for capacitive this data sheet. Multiplexed features are sorted by the sensors. priority given to a feature, with the highest priority • Parallel Master Port: One of the general purpose peripheral being listed first. I/O ports can be reconfigured for enhanced parallel data communications. In this mode, the port can be configured for both master and slave operations, and supports 8-bit transfers with up to 16 external address lines in Master modes. • Real-Time Clock/Calendar: This module implements a full-featured clock and calendar with alarm functions in hardware, freeing up the timer resources and program memory space for the use of the core application. DS39905E-page 10  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 1-1: DEVICE FEATURES FOR THE PIC24FJ256GA110 FAMILY: 64-PIN DEVICES Features PIC24FJ64GA106 PIC24FJ128GA106 PIC24FJ192GA106 PIC24FJ256GA106 Operating Frequency DC – 32 MHz Program Memory (bytes) 64K 128K 192K 256K Program Memory (instructions) 22,016 44,032 67,072 87,552 Data Memory (bytes) 16,384 Interrupt Sources 66 (62/4) (soft vectors/NMI traps) I/O Ports Ports B, C, D, E, F, G Total I/O Pins 53 Remappable Pins 31 (29 I/O, 2 input only) Timers: Total Number (16-bit) 5(1) 32-Bit (from paired 16-bit timers) 2 Input Capture Channels 9(1) Output Compare/PWM 9(1) Channels Input Change Notification 53 Interrupt Serial Communications: UART 4(1) SPI (3-wire/4-wire) 3(1) I2C™ 3 Parallel Communications Yes (PMP/PSP) JTAG Boundary Scan Yes 10-Bit Analog-to-Digital Module 16 (input channels) Analog Comparators 3 CTMU Interface Yes Resets (and delays) POR, BOR, RESET Instruction, MCLR, WDT; Illegal Opcode, REPEAT Instruction, Hardware Traps, Configuration Word Mismatch (PWRT, OST, PLL Lock) Instruction Set 76 Base Instructions, Multiple Addressing Mode Variations Packages 64-Pin TQFP Note 1: Peripherals are accessible through remappable pins.  2010 Microchip Technology Inc. DS39905E-page 11

PIC24FJ256GA110 FAMILY TABLE 1-2: DEVICE FEATURES FOR THE PIC24FJ256GA110 FAMILY: 80-PIN DEVICES Features PIC24FJ64GA108 PIC24FJ128GA108 PIC24FJ192GA108 PIC24FJ256GA108 Operating Frequency DC – 32 MHz Program Memory (bytes) 64K 128K 192K 256K Program Memory (instructions) 22,016 44,032 67,072 87,552 Data Memory (bytes) 16,384 Interrupt Sources 66 (62/4) (soft vectors/NMI traps) I/O Ports Ports A, B, C, D, E, F, G Total I/O Pins 69 Remappable Pins 42 (31 I/O, 11 input only) Timers: Total Number (16-bit) 5(1) 32-Bit (from paired 16-bit timers) 2 Input Capture Channels 9(1) Output Compare/PWM 9(1) Channels Input Change Notification 69 Interrupt Serial Communications: UART 4(1) SPI (3-wire/4-wire) 3(1) I2C™ 3 Parallel Communications Yes (PMP/PSP) JTAG Boundary Scan Yes 10-Bit Analog-to-Digital Module 16 (input channels) Analog Comparators 3 CTMU Interface Yes Resets (and delays) POR, BOR, RESET Instruction, MCLR, WDT; Illegal Opcode, REPEAT Instruction, Hardware Traps, Configuration Word Mismatch (PWRT, OST, PLL Lock) Instruction Set 76 Base Instructions, Multiple Addressing Mode Variations Packages 80-Pin TQFP Note 1: Peripherals are accessible through remappable pins. DS39905E-page 12  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 1-3: DEVICE FEATURES FOR THE PIC24FJ256GA110 FAMILY: 100-PIN DEVICES Features PIC24FJ64GA110 PIC24FJ128GA110 PIC24FJ192GA110 PIC24FJ256GA110 Operating Frequency DC – 32 MHz Program Memory (bytes) 64K 128K 192K 256K Program Memory (instructions) 22,016 44,032 67,072 87,552 Data Memory (bytes) 16,384 Interrupt Sources 66 (62/4) (soft vectors/NMI traps) I/O Ports Ports A, B, C, D, E, F, G Total I/O Pins 85 Remappable Pins 46 (32 I/O, 14 input only) Timers: Total Number (16-bit) 5(1) 32-Bit (from paired 16-bit timers) 2 Input Capture Channels 9(1) Output Compare/PWM 9(1) Channels Input Change Notification 85 Interrupt Serial Communications: UART 4(1) SPI (3-wire/4-wire) 3(1) I2C™ 3 Parallel Communications Yes (PMP/PSP) JTAG Boundary Scan Yes 10-Bit Analog-to-Digital Module 16 (input channels) Analog Comparators 3 CTMU Interface Yes Resets (and delays) POR, BOR, RESET Instruction, MCLR, WDT; Illegal Opcode, REPEAT Instruction, Hardware Traps, Configuration Word Mismatch (PWRT, OST, PLL Lock) Instruction Set 76 Base Instructions, Multiple Addressing Mode Variations Packages 100-Pin TQFP Note 1: Peripherals are accessible through remappable pins.  2010 Microchip Technology Inc. DS39905E-page 13

PIC24FJ256GA110 FAMILY FIGURE 1-1: PIC24FJ256GA110 FAMILY GENERAL BLOCK DIAGRAM Data Bus Interrupt Controller PORTA(1) 16 8 16 16 (13 I/O) PSV & Table Data Latch Data Access Control Block PCH PCL DataRAM 23 Program Counter Address PORTB Stack Repeat Latch Control Control Logic Logic (16 I/O) 16 23 16 Address Latch Read AGU Write AGU PORTC(1) Program Memory (8 I/O) Data Latch Address Bus EA MUX 16 a 24 Dat 16 16 PORTD(1) al Inst Latch Liter (16 I/O) Inst Register Instruction Decode & PORTE(1) Control Divide OSCO/CLKO Control Signals Support 16 x 16 (10 I/O) OSCI/CLKI 17x17 W Reg Array Timing Power-up Multiplier Generation Timer Oscillator REFO FRC/LPRC Start-up Timer PORTF(1) Oscillators Power-on 16-Bit ALU Reset (11 I/O) 16 Precision Band Gap Watchdog Reference Timer ENVREG BOR and RVeoglutalagteor LVD(2) PORTG(1) (12 I/O) VDDCORE/VCAP VDD,VSS MCLR 10-Bit Timer1 Timer2/3(3) Timer4/5(3) RTCC Comparators(3) ADC PMP/PSP 1-I9C(3) PW1-M9(/3O)C ICNs(1) 1/S2/P3I(3) 1I/22C/3 1/U2A/3R/4T(3) CTMU Note 1: Not all I/O pins or features are implemented on all device pinout configurations. See Table1-4 for specific implementations by pin count. 2: BOR functionality is provided when the on-board voltage regulator is enabled. 3: These peripheral I/Os are only accessible through remappable pins. DS39905E-page 14  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP AN0 16 20 25 I ANA A/D Analog Inputs. AN1 15 19 24 I ANA AN2 14 18 23 I ANA AN3 13 17 22 I ANA AN4 12 16 21 I ANA AN5 11 15 20 I ANA AN6 17 21 26 I ANA AN7 18 22 27 I ANA AN8 21 27 32 I ANA AN9 22 28 33 I ANA AN10 23 29 34 I ANA AN11 24 30 35 I ANA AN12 27 33 41 I ANA AN13 28 34 42 I ANA AN14 29 35 43 I ANA AN15 30 36 44 I ANA ASCL2 — — 66 I/O I2C Alternate I2C2 Synchronous Serial Clock Input/Output. ASDA2 — — 67 I/O I2C Alternate I2C2 Data Input/Output. AVDD 19 25 30 P — Positive Supply for Analog modules. AVSS 20 26 31 P — Ground Reference for Analog modules. C1INA 11 15 20 I ANA Comparator 1 Input A. C1INB 12 16 21 I ANA Comparator 1 Input B. C1INC 5 7 11 I ANA Comparator 1 Input C. C1IND 4 6 10 I ANA Comparator 1 Input D. C2INA 13 17 22 I ANA Comparator 2 Input A. C2INB 14 18 23 I ANA Comparator 2 Input B. C2INC 8 10 14 I ANA Comparator 2 Input C. C2IND 6 8 12 I ANA Comparator 2 Input D. C3INA 55 69 84 I ANA Comparator 3 Input A. C3INB 54 68 83 I ANA Comparator 3 Input B. C3INC 48 60 74 I ANA Comparator 3 Input C. C3IND 47 59 73 I ANA Comparator 3 Input D. CLKI 39 49 63 I ANA Main Clock Input Connection. CLKO 40 50 64 O — System Clock Output. Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer  2010 Microchip Technology Inc. DS39905E-page 15

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS (CONTINUED) Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP CN0 48 60 74 I ST Interrupt-on-Change Inputs. CN1 47 59 73 I ST CN2 16 20 25 I ST CN3 15 19 24 I ST CN4 14 18 23 I ST CN5 13 17 22 I ST CN6 12 16 21 I ST CN7 11 15 20 I ST CN8 4 6 10 I ST CN9 5 7 11 I ST CN10 6 8 12 I ST CN11 8 10 14 I ST CN12 30 36 44 I ST CN13 52 66 81 I ST CN14 53 67 82 I ST CN15 54 68 83 I ST CN16 55 69 84 I ST CN17 31 39 49 I ST CN18 32 40 50 I ST CN19 — 65 80 I ST CN20 — 37 47 I ST CN21 — 38 48 I ST CN22 40 50 64 I ST CN23 39 49 63 I ST CN24 17 21 26 I ST CN25 18 22 27 I ST CN26 21 27 32 I ST CN27 22 28 33 I ST CN28 23 29 34 I ST CN29 24 30 35 I ST CN30 27 33 41 I ST CN31 28 34 42 I ST CN32 29 35 43 I ST CN33 — — 17 I ST CN34 — — 38 I ST CN35 — — 58 I ST CN36 — — 59 I ST CN37 — — 60 I ST CN38 — — 61 I ST CN39 — — 91 I ST CN40 — — 92 I ST CN41 — 23 28 I ST CN42 — 24 29 I ST Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer DS39905E-page 16  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS (CONTINUED) Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP CN43 — 52 66 I ST Interrupt-on-Change Inputs. CN44 — 53 67 I ST CN45 — 4 6 I ST CN46 — — 7 I ST CN47 — 5 8 I ST CN48 — — 9 I ST CN49 46 58 72 I ST CN50 49 61 76 I ST CN51 50 62 77 I ST CN52 51 63 78 I ST CN53 42 54 68 I ST CN54 43 55 69 I ST CN55 44 56 70 I ST CN56 45 57 71 I ST CN57 — 64 79 I ST CN58 60 76 93 I ST CN59 61 77 94 I ST CN60 62 78 98 I ST CN61 63 79 99 I ST CN62 64 80 100 I ST CN63 1 1 3 I ST CN64 2 2 4 I ST CN65 3 3 5 I ST CN66 — 13 18 I ST CN67 — 14 19 I ST CN68 58 72 87 I ST CN69 59 73 88 I ST CN70 34 42 52 I ST CN71 33 41 51 I ST CN72 35 45 55 I ST CN73 — 44 54 I ST CN74 — 43 53 I ST CN75 — — 40 I ST CN76 — — 39 I ST CN77 — 75 90 I ST CN78 — 74 89 I ST CN79 — — 96 I ST CN80 — — 97 I ST CN81 — — 95 I ST CN82 — — 1 I ST CN83 37 47 57 I ST CN84 36 46 56 I ST Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer  2010 Microchip Technology Inc. DS39905E-page 17

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS (CONTINUED) Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP CTED1 28 34 42 I ANA CTMU External Edge Input 1. CTED2 27 33 41 I ANA CTMU External Edge Input 2. CTPLS 29 35 43 O — CTMU Pulse Output. CVREF 23 29 34 O — Comparator Voltage Reference Output. ENVREG 57 71 86 I ST Voltage Regulator Enable. INT0 35 45 55 I ST External Interrupt Input. MCLR 7 9 13 I ST Master Clear (device Reset) Input. This line is brought low to cause a Reset. OSCI 39 49 63 I ANA Main Oscillator Input Connection. OSCO 40 50 64 O ANA Main Oscillator Output Connection. PGEC1 15 19 24 I/O ST In-Circuit Debugger/Emulator/ICSP™ Programming Clock. PGED1 16 20 25 I/O ST In-Circuit Debugger/Emulator/ICSP Programming Data. PGEC2 17 21 26 I/O ST In-Circuit Debugger/Emulator/ICSP Programming Clock. PGED2 18 22 27 I/O ST In-Circuit Debugger/Emulator/ICSP Programming Data. PGEC3 11 15 20 I/O ST In-Circuit Debugger/Emulator/ICSP Programming Clock. PGED3 12 16 21 I/O ST In-Circuit Debugger/Emulator/ICSP Programming Data. PMA0 30 36 44 I/O ST Parallel Master Port Address Bit 0 Input (Buffered Slave modes) and Output (Master modes). PMA1 29 35 43 I/O ST Parallel Master Port Address Bit 1 Input (Buffered Slave modes) and Output (Master modes). PMA2 8 10 14 O — Parallel Master Port Address (Demultiplexed Master PMA3 6 8 12 O — modes). PMA4 5 7 11 O — PMA5 4 6 10 O — PMA6 16 24 29 O — PMA7 22 23 28 O — PMA8 32 40 50 O — PMA9 31 39 49 O — PMA10 28 34 42 O — PMA11 27 33 41 O — PMA12 24 30 35 O — PMA13 23 29 34 O — PMCS1 45 57 71 I/O ST/TTL Parallel Master Port Chip Select 1 Strobe/Address Bit 15. PMCS2 44 56 70 O ST Parallel Master Port Chip Select 2 Strobe/Address Bit 14. PMBE 51 63 78 O — Parallel Master Port Byte Enable Strobe. PMD0 60 76 93 I/O ST/TTL Parallel Master Port Data (Demultiplexed Master mode) or PMD1 61 77 94 I/O ST/TTL Address/Data (Multiplexed Master modes). PMD2 62 78 98 I/O ST/TTL PMD3 63 79 99 I/O ST/TTL PMD4 64 80 100 I/O ST/TTL PMD5 1 1 3 I/O ST/TTL PMD6 2 2 4 I/O ST/TTL PMD7 3 3 5 I/O ST/TTL PMRD 53 67 82 O — Parallel Master Port Read Strobe. PMWR 52 66 81 O — Parallel Master Port Write Strobe. Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer DS39905E-page 18  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS (CONTINUED) Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP RA0 — — 17 I/O ST PORTA Digital I/O. RA1 — — 38 I/O ST RA2 — — 58 I/O ST RA3 — — 59 I/O ST RA4 — — 60 I/O ST RA5 — — 61 I/O ST RA6 — — 91 I/O ST RA7 — — 92 I/O ST RA9 — 23 28 I/O ST RA10 — 24 29 I/O ST RA14 — 52 66 I/O ST RA15 — 53 67 I/O ST RB0 16 20 25 I/O ST PORTB Digital I/O. RB1 15 19 24 I/O ST RB2 14 18 23 I/O ST RB3 13 17 22 I/O ST RB4 12 16 21 I/O ST RB5 11 15 20 I/O ST RB6 17 21 26 I/O ST RB7 18 22 27 I/O ST RB8 21 27 32 I/O ST RB9 22 28 33 I/O ST RB10 23 29 34 I/O ST RB11 24 30 35 I/O ST RB12 27 33 41 I/O ST RB13 28 34 42 I/O ST RB14 29 35 43 I/O ST RB15 30 36 44 I/O ST RC1 — 4 6 I/O ST PORTC Digital I/O. RC2 — — 7 I/O ST RC3 — 5 8 I/O ST RC4 — — 9 I/O ST RC12 39 49 63 I/O ST RC13 47 59 73 I/O ST RC14 48 60 74 I/O ST RC15 40 50 64 I/O ST Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer  2010 Microchip Technology Inc. DS39905E-page 19

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS (CONTINUED) Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP RD0 46 58 72 I/O ST PORTD Digital I/O. RD1 49 61 76 I/O ST RD2 50 62 77 I/O ST RD3 51 63 78 I/O ST RD4 52 66 81 I/O ST RD5 53 67 82 I/O ST RD6 54 68 83 I/O ST RD7 55 69 84 I/O ST RD8 42 54 68 I/O ST RD9 43 55 69 I/O ST RD10 44 56 70 I/O ST RD11 45 57 71 I/O ST RD12 — 64 79 I/O ST RD13 — 65 80 I/O ST RD14 — 37 47 I/O ST RD15 — 38 48 I/O ST RE0 60 76 93 I/O ST PORTE Digital I/O. RE1 61 77 94 I/O ST RE2 62 78 98 I/O ST RE3 63 79 99 I/O ST RE4 64 80 100 I/O ST RE5 1 1 3 I/O ST RE6 2 2 4 I/O ST RE7 3 3 5 I/O ST RE8 — 13 18 I/O ST RE9 — 14 19 I/O ST REFO 30 36 44 O — Reference Clock Output. RF0 58 72 87 I/O ST PORTF Digital I/O. RF1 59 73 88 I/O ST RF2 34 42 52 I/O ST RF3 33 41 51 I/O ST RF4 31 39 49 I/O ST RF5 32 40 50 I/O ST RF6 35 45 55 I/O ST RF7 — 44 54 I/O ST RF8 — 43 53 I/O ST RF12 — — 40 I/O ST RF13 — — 39 I/O ST Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer DS39905E-page 20  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS (CONTINUED) Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP RG0 — 75 90 I/O ST PORTG Digital I/O. RG1 — 74 89 I/O ST RG2 37 47 57 I/O ST RG3 36 46 56 I/O ST RG6 4 6 10 I/O ST RG7 5 7 11 I/O ST RG8 6 8 12 I/O ST RG9 8 10 14 I/O ST RG12 — — 96 I/O ST RG13 — — 97 I/O ST RG14 — — 95 I/O ST RG15 — — 1 I/O ST RP0 16 20 25 I/O ST Remappable Peripheral (input or output). RP1 15 19 24 I/O ST RP2 42 54 68 I/O ST RP3 44 56 70 I/O ST RP4 43 55 69 I/O ST RP5 — 38 48 I/O ST RP6 17 21 26 I/O ST RP7 18 22 27 I/O ST RP8 21 27 32 I/O ST RP9 22 28 33 I/O ST RP10 31 39 49 I/O ST RP11 46 58 72 I/O ST RP12 45 57 71 I/O ST RP13 14 18 23 I/O ST RP14 29 35 43 I/O ST RP15 — 43 53 I/O ST RP16 33 41 51 I/O ST RP17 32 40 50 I/O ST RP18 11 15 20 I/O ST RP19 6 8 12 I/O ST RP20 53 67 82 I/O ST RP21 4 6 10 I/O ST RP22 51 63 78 I/O ST RP23 50 62 77 I/O ST RP24 49 61 76 I/O ST RP25 52 66 81 I/O ST RP26 5 7 11 I/O ST RP27 8 10 14 I/O ST RP28 12 16 21 I/O ST RP29 30 36 44 I/O ST RP30 34 42 52 I/O ST RP31 — — 39 I/O ST Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer  2010 Microchip Technology Inc. DS39905E-page 21

PIC24FJ256GA110 FAMILY TABLE 1-4: PIC24FJ256GA110 FAMILY PINOUT DESCRIPTIONS (CONTINUED) Pin Number Input Function I/O Description 64-Pin 80-Pin 100-Pin Buffer TQFP, QFN TQFP TQFP RPI32 — — 40 I ST Remappable Peripheral (input only). RPI33 — 13 18 I ST RPI34 — 14 19 I ST RPI35 — 53 67 I ST RPI36 — 52 66 I ST RPI37 48 60 74 I ST RPI38 — 4 6 I ST RPI39 — — 7 I ST RPI40 — 5 8 I ST RPI41 — — 9 I ST RPI42 — 64 79 I ST RPI43 — 37 47 I ST RPI44 — 44 54 I ST RPI45 35 45 55 I ST RTCC 42 54 68 O — Real-Time Clock Alarm/Seconds Pulse Output. SCL1 37 47 57 I/O I2C I2C1 Synchronous Serial Clock Input/Output. SCL2 32 52 58 I/O I2C I2C2 Synchronous Serial Clock Input/Output. SCL3 2 2 4 I/O I2C I2C3 Synchronous Serial Clock Input/Output. SDA1 36 46 56 I/O I2C I2C1 Data Input/Output. SDA2 31 53 59 I/O I2C I2C2 Data Input/Output. SDA3 3 3 5 I/O I2C I2C3 Data Input/Output. SOSCI 47 59 73 I ANA Secondary Oscillator/Timer1 Clock Input. SOSCO 48 60 74 O ANA Secondary Oscillator/Timer1 Clock Output. T1CK 48 60 74 I ST Timer1 Clock. TCK 27 33 38 I ST JTAG Test Clock Input. TDI 28 34 60 I ST JTAG Test Data Input. TDO 24 14 61 O — JTAG Test Data Output. TMS 23 13 17 I ST JTAG Test Mode Select Input. VCAP 56 70 85 P — External Filter Capacitor Connection (regulator enabled). VDD 10, 26, 38 12, 32, 48 2, 16, 37, P — Positive Supply for Peripheral Digital Logic and I/O Pins. 46, 62 VDDCORE 56 70 85 P — Positive Supply for Microcontroller Core Logic (regulator disabled). VREF- 15 23 28 I ANA A/D and Comparator Reference Voltage (low) Input. VREF+ 16 24 29 I ANA A/D and Comparator Reference Voltage (high) Input. VSS 9, 25, 41 11, 31, 51 15, 36, 45, P — Ground Reference for Logic and I/O Pins. 65, 75 Legend: TTL = TTL input buffer ST = Schmitt Trigger input buffer ANA = Analog level input/output I2C™ = I2C/SMBus input buffer DS39905E-page 22  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 2.0 GUIDELINES FOR GETTING FIGURE 2-1: RECOMMENDED STARTED WITH 16-BIT MINIMUM CONNECTIONS MICROCONTROLLERS C2(2) 2.1 Basic Connection Requirements VDD Getting started with the PIC24FJ256GA110 family R1 DD SS (1) (1) family of 16-bit microcontrollers requires attention to a V V R2 minimal set of device pin connections before MCLR (EN/DIS)VREG proceeding with development. VCAP/VDDCORE C1 The following pins must always be connected: C7 PIC24FJXXXX • All VDD and VSS pins (see Section2.2 “Power Supply Pins”) VSS VDD C6(2) C3(2) • All AVDD and AVSS pins, regardless of whether or not the analog device features are used VDD D S VSS D S D S (see Section2.2 “Power Supply Pins”) V V D S A A V V • MCLR pin (see Section2.3 “Master Clear (MCLR) Pin”) C5(2) C4(2) • ENVREG/DISVREG and VCAP/VDDCORE pins (PIC24F J devices only) (see Section2.4 “Voltage Regulator Pins Key (all values are recommendations): (ENVREG/DISVREG and VCAP/VDDCORE)”) C1 through C6: 0.1 F, 20V ceramic These pins must also be connected if they are being C7: 10 F, 6.3V or greater, tantalum or ceramic used in the end application: R1: 10 kΩ • PGECx/PGEDx pins used for In-Circuit Serial R2: 100Ω to 470Ω Programming™ (ICSP™) and debugging purposes Note 1: See Section2.4 “Voltage Regulator Pins (see Section2.5 “ICSP Pins”) (ENVREG/DISVREG and VCAP/VDDCORE)” • OSCI and OSCO pins when an external oscillator for explanation of ENVREG/DISVREG pin source is used connections. (see Section2.6 “External Oscillator Pins”) 2: The example shown is for a PIC24F device Additionally, the following pins may be required: with five VDD/VSS and AVDD/AVSS pairs. Other devices may have more or less pairs; • VREF+/VREF- pins used when external voltage adjust the number of decoupling capacitors reference for analog modules is implemented appropriately. Note: The AVDD and AVSS pins must always be connected, regardless of whether any of the analog modules are being used. The minimum mandatory connections are shown in Figure2-1.  2010 Microchip Technology Inc. DS39905E-page 23

PIC24FJ256GA110 FAMILY 2.2 Power Supply Pins 2.3 Master Clear (MCLR) Pin 2.2.1 DECOUPLING CAPACITORS The MCLR pin provides two specific device functions: device Reset, and device programming The use of decoupling capacitors on every pair of and debugging. If programming and debugging are power supply pins, such as VDD, VSS, AVDD and not required in the end application, a direct AVSS is required. connection to VDD may be all that is required. The Consider the following criteria when using decoupling addition of other components, to help increase the capacitors: application’s resistance to spurious Resets from voltage sags, may be beneficial. A typical • Value and type of capacitor: A 0.1 F (100 nF), configuration is shown in Figure2-1. Other circuit 10-20V capacitor is recommended. The capacitor designs may be implemented, depending on the should be a low-ESR device with a resonance application’s requirements. frequency in the range of 200MHz and higher. Ceramic capacitors are recommended. During programming and debugging, the resistance • Placement on the printed circuit board: The and capacitance that can be added to the pin must decoupling capacitors should be placed as close be considered. Device programmers and debuggers to the pins as possible. It is recommended to drive the MCLR pin. Consequently, specific voltage place the capacitors on the same side of the levels (VIH and VIL) and fast signal transitions must not be adversely affected. Therefore, specific values board as the device. If space is constricted, the of R1 and C1 will need to be adjusted based on the capacitor can be placed on another layer on the application and PCB requirements. For example, it is PCB using a via; however, ensure that the trace recommended that the capacitor, C1, be isolated length from the pin to the capacitor is no greater from the MCLR pin during programming and than 0.25inch (6mm). debugging operations by using a jumper (Figure2-2). • Handling high-frequency noise: If the board is The jumper is replaced for normal run-time experiencing high-frequency noise (upward of operations. tens of MHz), add a second ceramic type capaci- tor in parallel to the above described decoupling Any components associated with the MCLR pin capacitor. The value of the second capacitor can should be placed within 0.25 inch (6mm) of the pin. be in the range of 0.01F to 0.001F. Place this second capacitor next to each primary decoupling FIGURE 2-2: EXAMPLE OF MCLR PIN capacitor. In high-speed circuit designs, consider CONNECTIONS implementing a decade pair of capacitances as close to the power and ground pins as possible VDD (e.g., 0.1F in parallel with 0.001F). • Maximizing performance: On the board layout R1 from the power supply circuit, run the power and R2 return traces to the decoupling capacitors first, MCLR and then to the device pins. This ensures that the JP PIC24FXXXX decoupling capacitors are first in the power chain. Equally important is to keep the trace length C1 between the capacitor and the power pins to a minimum, thereby reducing PCB trace inductance. Note 1: R1 10k is recommended. A suggested 2.2.2 TANK CAPACITORS starting value is 10k. Ensure that the On boards with power traces running longer than six MCLR pin VIH and VIL specifications are met. inches in length, it is suggested to use a tank capacitor 2: R2 470 will limit any current flowing into for integrated circuits including microcontrollers to MCLR from the external capacitor, C, in the supply a local power source. The value of the tank event of MCLR pin breakdown, due to Electrostatic Discharge (ESD) or Electrical capacitor should be determined based on the trace Overstress (EOS). Ensure that the MCLR pin resistance that connects the power supply source to VIH and VIL specifications are met. the device, and the maximum current drawn by the device in the application. In other words, select the tank capacitor so that it meets the acceptable voltage sag at the device. Typical values range from 4.7F to 47F. DS39905E-page 24  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 2.4 Voltage Regulator Pins Designers may use Figure2-3 to evaluate ESR (ENVREG/DISVREG and equivalence of candidate devices. VCAP/VDDCORE) The placement of this capacitor should be close to VCAP/VDDCORE. It is recommended that the trace Note: This section applies only to PIC24F J length not exceed 0.25inch (6mm). Refer to devices with an on-chip voltage regulator. Section28.0 “Electrical Characteristics” for additional information. The on-chip voltage regulator enable/disable pin (ENVREG or DISVREG, depending on the device When the regulator is disabled, the VCAP/VDDCORE pin family) must always be connected directly to either a must be tied to a voltage supply at the VDDCORE level. supply voltage or to ground. The particular connection Refer to Section28.0 “Electrical Characteristics” for is determined by whether or not the regulator is to be information on VDD and VDDCORE. used: FIGURE 2-3: FREQUENCY vs. ESR • For ENVREG, tie to VDD to enable the regulator, PERFORMANCE FOR or to ground to disable the regulator SUGGESTED VCAP • For DISVREG, tie to ground to enable the regulator or to VDD to disable the regulator 10 Refer to Section25.2 “On-Chip Voltage Regulator” for details on connecting and using the on-chip 1 regulator. ) When the regulator is enabled, a low-ESR (<5Ω) R ( 0.1 capacitor is required on the VCAP/VDDCORE pin to S E stabilize the voltage regulator output voltage. The VCAP/VDDCORE pin must not be connected to VDD and 0.01 must use a capacitor of 10 µF connected to ground. The type can be ceramic or tantalum. Suitable examples of 0.001 capacitors are shown in Table2-1. Capacitors with 0.01 0.1 1 10 100 1000 10,000 equivalent specification can be used. Frequency (MHz) Note: Typical data measurement at 25°C, 0V DC bias. . TABLE 2-1: SUITABLE CAPACITOR EQUIVALENTS Nominal Make Part # Base Tolerance Rated Voltage Temp. Range Capacitance TDK C3216X7R1C106K 10 µF ±10% 16V -55 to 125ºC TDK C3216X5R1C106K 10 µF ±10% 16V -55 to 85ºC Panasonic ECJ-3YX1C106K 10 µF ±10% 16V -55 to 125ºC Panasonic ECJ-4YB1C106K 10 µF ±10% 16V -55 to 85ºC Murata GRM32DR71C106KA01L 10 µF ±10% 16V -55 to 125ºC Murata GRM31CR61C106KC31L 10 µF ±10% 16V -55 to 85ºC  2010 Microchip Technology Inc. DS39905E-page 25

PIC24FJ256GA110 FAMILY 2.4.1 CONSIDERATIONS FOR CERAMIC FIGURE 2-4: DC BIAS VOLTAGE vs. CAPACITORS CAPACITANCE CHARACTERISTICS In recent years, large value, low-voltage, surface-mount ceramic capacitors have become very cost effective in sizes up to a few tens of microfarad. The low-ESR, small physical size and other properties make ceramic %) 10 e ( 0 capacitors very attractive in many types of applications. ng-10 16V Capacitor ha-20 Ceramic capacitors are suitable for use with the inter- C-30 nal voltage regulator of this microcontroller. However, ance --5400 10V Capacitor some care is needed in selecting the capacitor to cit-60 ensure that it maintains sufficient capacitance over the Capa--8700 6.3V Capacitor intended operating range of the application. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 DC Bias Voltage (VDC) Typical low-cost, 10 F ceramic capacitors are available in X5R, X7R and Y5V dielectric ratings (other types are also available, but are less common). The initial toler- When selecting a ceramic capacitor to be used with the ance specifications for these types of capacitors are internal voltage regulator, it is suggested to select a often specified as ±10% to ±20% (X5R and X7R), or high-voltage rating, so that the operating voltage is a -20%/+80% (Y5V). However, the effective capacitance small percentage of the maximum rated capacitor volt- that these capacitors provide in an application circuit will age. For example, choose a ceramic capacitor rated at also vary based on additional factors, such as the 16V for the 2.5V or 1.8V core voltage. Suggested applied DC bias voltage and the temperature. The total capacitors are shown in Table2-1. in-circuit tolerance is, therefore, much wider than the initial tolerance specification. 2.5 ICSP Pins The X5R and X7R capacitors typically exhibit satisfac- The PGECx and PGEDx pins are used for In-Circuit tory temperature stability (ex: ±15% over a wide Serial Programming (ICSP) and debugging purposes. temperature range, but consult the manufacturer's data It is recommended to keep the trace length between sheets for exact specifications). However, Y5V capaci- the ICSP connector and the ICSP pins on the device as tors typically have extreme temperature tolerance short as possible. If the ICSP connector is expected to specifications of +22%/-82%. Due to the extreme tem- experience an ESD event, a series resistor is recom- perature tolerance, a 10 F nominal rated Y5V type mended, with the value in the range of a few tens of capacitor may not deliver enough total capacitance to ohms, not to exceed 100Ω. meet minimum internal voltage regulator stability and Pull-up resistors, series diodes and capacitors on the transient response requirements. Therefore, Y5V PGECx and PGEDx pins are not recommended as they capacitors are not recommended for use with the will interfere with the programmer/debugger communi- internal regulator if the application must operate over a cations to the device. If such discrete components are wide temperature range. an application requirement, they should be removed In addition to temperature tolerance, the effective from the circuit during programming and debugging. capacitance of large value ceramic capacitors can vary Alternatively, refer to the AC/DC characteristics and substantially, based on the amount of DC voltage timing requirements information in the respective applied to the capacitor. This effect can be very signifi- device Flash programming specification for information cant, but is often overlooked or is not always on capacitive loading limits and pin input voltage high documented. (VIH) and input low (VIL) requirements. Typical DC bias voltage vs. capacitance graph for X7R For device emulation, ensure that the “Communication type capacitors is shown in Figure2-4. Channel Select” (i.e., PGECx/PGEDx pins), programmed into the device, matches the physical connections for the ICSP to the Microchip debugger/emulator tool. For more information on available Microchip development tools connection requirements, refer to Section27.0 “Development Support”. DS39905E-page 26  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 2.6 External Oscillator Pins FIGURE 2-5: SUGGESTED PLACEMENT OF THE Many microcontrollers have options for at least two OSCILLATOR CIRCUIT oscillators: a high-frequency primary oscillator and a low-frequency secondary oscillator (refer to Single-Sided and In-line Layouts: Section8.0 “Oscillator Configuration” for details). Copper Pour Primary Oscillator The oscillator circuit should be placed on the same (tied to ground) Crystal side of the board as the device. Place the oscillator DEVICE PINS circuit close to the respective oscillator pins with no more than 0.5inch (12mm) between the circuit components and the pins. The load capacitors should be placed next to the oscillator itself, on the same side Primary OSCI Oscillator of the board. C1 ` OSCO Use a grounded copper pour around the oscillator cir- cuit to isolate it from surrounding circuits. The C2 GND grounded copper pour should be routed directly to the ` MCU ground. Do not run any signal traces or power SOSCO traces inside the ground pour. Also, if using a two-sided board, avoid any traces on the other side of the board Secondary SOSC I where the crystal is placed. Oscillator Crystal ` Layout suggestions are shown in Figure2-5. In-line packages may be handled with a single-sided layout that completely encompasses the oscillator pins. With Sec Oscillator: C1 Sec Oscillator: C2 fine-pitch packages, it is not always possible to com- pletely surround the pins and components. A suitable solution is to tie the broken guard sections to a mirrored Fine-Pitch (Dual-Sided) Layouts: ground layer. In all cases, the guard trace(s) must be returned to ground. Top Layer Copper Pour (tied to ground) In planning the application’s routing and I/O assign- ments, ensure that adjacent port pins, and other Bottom Layer signals in close proximity to the oscillator, are benign Copper Pour (i.e., free of high frequencies, short rise and fall times (tied to ground) and other similar noise). OSCO For additional information and design guidance on oscillator circuits, please refer to these Microchip C2 Application Notes, available at the corporate web site Oscillator (www.microchip.com): GND Crystal • AN826, “Crystal Oscillator Basics and Crystal C1 Selection for rfPIC™ and PICmicro® Devices” • AN849, “Basic PICmicro® Oscillator Design” OSCI • AN943, “Practical PICmicro® Oscillator Analysis and Design” • AN949, “Making Your Oscillator Work” DEVICE PINS  2010 Microchip Technology Inc. DS39905E-page 27

PIC24FJ256GA110 FAMILY 2.7 Configuration of Analog and If your application needs to use certain A/D pins as Digital Pins During ICSP analog input pins during the debug session, the user application must modify the appropriate bits during Operations initialization of the ADC module, as follows: If an ICSP compliant emulator is selected as a debug- • For devices with an ADnPCFG register, clear the ger, it automatically initializes all of the A/D input pins bits corresponding to the pin(s) to be configured (ANx) as “digital” pins. Depending on the particular as analog. Do not change any other bits, particu- device, this is done by setting all bits in the ADnPCFG larly those corresponding to the PGECx/PGEDx register(s), or clearing all bit in the ANSx registers. pair, at any time. All PIC24F devices will have either one or more • For devices with ANSx registers, set the bits ADnPCFG registers or several ANSx registers (one for corresponding to the pin(s) to be configured as each port); no device will have both. Refer to (choose analog. Do not change any other bits, particularly one xref: Sectionx.x.x in I/O chapter or Sectionx.0 those corresponding to the PGECx/PGEDx pair, A/D Chapter) for more specific information. at any time. The bits in these registers that correspond to the A/D When a Microchip debugger/emulator is used as a pins that initialized the emulator must not be changed programmer, the user application firmware must by the user application firmware; otherwise, correctly configure the ADnPCFG or ANSx registers. communication errors will result between the debugger Automatic initialization of this register is only done and the device. during debugger operation. Failure to correctly configure the register(s) will result in all A/D pins being recognized as analog input pins, resulting in the port value being read as a logic '0', which may affect user application functionality. 2.8 Unused I/Os Unused I/O pins should be configured as outputs and driven to a logic low state. Alternatively, connect a 1kΩ to 10kΩ resistor to VSS on unused pins and drive the output to logic low. DS39905E-page 28  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 3.0 CPU For most instructions, the core is capable of executing a data (or program data) memory read, a working reg- Note: This data sheet summarizes the features of ister (data) read, a data memory write and a program this group of PIC24F devices. It is not (instruction) memory read per instruction cycle. As a intended to be a comprehensive reference result, three parameter instructions can be supported, source. For more information, refer to the allowing trinary operations (that is, A + B = C) to be “PIC24F Family Reference Manual”, executed in a single cycle. Section 2. “CPU” (DS39703). A high-speed, 17-bit by 17-bit multiplier has been included to significantly enhance the core arithmetic The PIC24F CPU has a 16-bit (data), modified Harvard capability and throughput. The multiplier supports architecture with an enhanced instruction set and a Signed, Unsigned and Mixed mode, 16-bit by 16-bit or 24-bit instruction word with a variable length opcode 8-bit by 8-bit integer multiplication. All multiply field. The Program Counter (PC) is 23 bits wide and instructions execute in a single cycle. addresses up to 4M instructions of user program memory space. A single-cycle instruction prefetch The 16-bit ALU has been enhanced with integer divide mechanism is used to help maintain throughput and pro- assist hardware that supports an iterative non-restoring vides predictable execution. All instructions execute in a divide algorithm. It operates in conjunction with the single cycle, with the exception of instructions that REPEAT instruction looping mechanism and a selection change the program flow, the double-word move of iterative divide instructions to support 32-bit (or (MOV.D) instruction and the table instructions. 16-bit), divided by 16-bit, integer signed and unsigned Overhead-free program loop constructs are supported division. All divide operations require 19 cycles to using the REPEAT instructions, which are interruptible at complete, but are interruptible at any cycle boundary. any point. The PIC24F has a vectored exception scheme with up PIC24F devices have sixteen, 16-bit working registers to 8 sources of non-maskable traps and up to 118 inter- in the programmer’s model. Each of the working rupt sources. Each interrupt source can be assigned to registers can act as a data, address or address offset one of seven priority levels. register. The 16th working register (W15) operates as A block diagram of the CPU is shown in Figure3-1. a Software Stack Pointer for interrupts and calls. The upper 32Kbytes of the data space memory map 3.1 Programmer’s Model can optionally be mapped into program space at any 16K word boundary defined by the 8-bit Program Space The programmer’s model for the PIC24F is shown in Visibility Page Address (PSVPAG) register. The program Figure3-2. All registers in the programmer’s model are to data space mapping feature lets any instruction memory mapped and can be manipulated directly by access program space as if it were data space. instructions. A description of each register is provided in Table3-1. All registers associated with the The Instruction Set Architecture (ISA) has been programmer’s model are memory mapped. significantly enhanced beyond that of the PIC18, but maintains an acceptable level of backward compatibil- ity. All PIC18 instructions and addressing modes are supported either directly or through simple macros. Many of the ISA enhancements have been driven by compiler efficiency needs. The core supports Inherent (no operand), Relative, Literal, Memory Direct and three groups of addressing modes. All modes support Register Direct and various Register Indirect modes. Each group offers up to seven addressing modes. Instructions are associated with predefined addressing modes depending upon their functional requirements.  2010 Microchip Technology Inc. DS39905E-page 29

PIC24FJ256GA110 FAMILY FIGURE 3-1: PIC24F CPU CORE BLOCK DIAGRAM PSV & Table Data Access Control Block Data Bus Interrupt Controller 16 8 16 16 Data Latch 23 PCH PCL Data RAM 16 23 Program Counter Stack Loop Address Control Control Latch Logic Logic 23 16 RAGU Address Latch WAGU Program Memory Address Bus EA MUX Data Latch ROM Latch 24 16 16 Instruction a Decode & Dat Control Instruction Reg al er Lit Control Signals to Various Blocks Hardware Multiplier 16 x 16 W Register Array Divide Support 16 16-Bit ALU 16 To Peripheral Modules DS39905E-page 30  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 3-1: CPU CORE REGISTERS Register(s) Name Description W0 through W15 Working Register Array PC 23-Bit Program Counter SR ALU STATUS Register SPLIM Stack Pointer Limit Value Register TBLPAG Table Memory Page Address Register PSVPAG Program Space Visibility Page Address Register RCOUNT Repeat Loop Counter Register CORCON CPU Control Register FIGURE 3-2: PROGRAMMER’S MODEL 15 0 W0 (WREG) Divider Working Registers W1 W2 Multiplier Registers W3 W4 W5 W6 W7 Working/Address W8 Registers W9 W10 W11 W12 W13 W14 Frame Pointer W15 Stack Pointer 0 Stack Pointer Limit SPLIM 0 Value Register 22 0 PC 0 Program Counter 7 0 Table Memory Page TBLPAG Address Register 7 0 Program Space Visibility PSVPAG Page Address Register 15 0 Repeat Loop Counter RCOUNT Register 15 SRH SRL 0 ———————DC IPL RA N OV Z C ALU STATUS Register (SR) 2 1 0 15 0 ————————————IPL3PSV—— CPU Control Register (CORCON) Registers or bits shadowed for PUSH.S and POP.S instructions.  2010 Microchip Technology Inc. DS39905E-page 31

PIC24FJ256GA110 FAMILY 3.2 CPU Control Registers REGISTER 3-1: SR: ALU STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — DC bit 15 bit 8 R/W-0(1) R/W-0(1) R/W-0(1) R-0 R/W-0 R/W-0 R/W-0 R/W-0 IPL2(2) IPL1(2) IPL0(2) RA N OV Z C bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8 DC: ALU Half Carry/Borrow bit 1 = A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred 0 = No carry-out from the 4th or 8th low-order bit of the result has occurred bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(1,2) 111 = CPU interrupt priority level is 7 (15); user interrupts disabled 110 = CPU interrupt priority level is 6 (14) 101 = CPU interrupt priority level is 5 (13) 100 = CPU interrupt priority level is 4 (12) 011 = CPU interrupt priority level is 3 (11) 010 = CPU interrupt priority level is 2 (10) 001 = CPU interrupt priority level is 1 (9) 000 = CPU interrupt priority level is 0 (8) bit 4 RA: REPEAT Loop Active bit 1 = REPEAT loop in progress 0 = REPEAT loop not in progress bit 3 N: ALU Negative bit 1 = Result was negative 0 = Result was non-negative (zero or positive) bit 2 OV: ALU Overflow bit 1 = Overflow occurred for signed (2’s complement) arithmetic in this arithmetic operation 0 = No overflow has occurred bit 1 Z: ALU Zero bit 1 = An operation which effects the Z bit has set it at some time in the past 0 = The most recent operation which effects the Z bit has cleared it (i.e., a non-zero result) bit 0 C: ALU Carry/Borrow bit 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note 1: The IPL Status bits are read-only when NSTDIS (INTCON1<15>) = 1. 2: The IPL Status bits are concatenated with the IPL3 bit (CORCON<3>) to form the CPU Interrupt Priority Level (IPL). The value in parentheses indicates the IPL when IPL3 = 1. DS39905E-page 32  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 3-2: CORCON: CPU CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/C-0 R/W-0 U-0 U-0 — — — — IPL3(1) PSV — — bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-4 Unimplemented: Read as ‘0’ bit 3 IPL3: CPU Interrupt Priority Level Status bit(1) 1 = CPU interrupt priority level is greater than 7 0 = CPU interrupt priority level is 7 or less bit 2 PSV: Program Space Visibility in Data Space Enable bit 1 = Program space visible in data space 0 = Program space not visible in data space bit 1-0 Unimplemented: Read as ‘0’ Note 1: User interrupts are disabled when IPL3 = 1.  2010 Microchip Technology Inc. DS39905E-page 33

PIC24FJ256GA110 FAMILY 3.3 Arithmetic Logic Unit (ALU) 3.3.2 DIVIDER The PIC24F ALU is 16 bits wide and is capable of addi- The divide block supports signed and unsigned integer tion, subtraction, bit shifts and logic operations. Unless divide operations with the following data sizes: otherwise mentioned, arithmetic operations are 2’s 1. 32-bit signed/16-bit signed divide complement in nature. Depending on the operation, the 2. 32-bit unsigned/16-bit unsigned divide ALU may affect the values of the Carry (C), Zero (Z), 3. 16-bit signed/16-bit signed divide Negative (N), Overflow (OV) and Digit Carry (DC) 4. 16-bit unsigned/16-bit unsigned divide Status bits in the SR register. The C and DC Status bits operate as Borrow and Digit Borrow bits, respectively, The quotient for all divide instructions ends up in W0 for subtraction operations. and the remainder in W1. Sixteen-bit signed and unsigned DIV instructions can specify any W register The ALU can perform 8-bit or 16-bit operations, for both the 16-bit divisor (Wn), and any W register depending on the mode of the instruction that is used. (aligned) pair (W(m + 1):Wm) for the 32-bit dividend. Data for the ALU operation can come from the W The divide algorithm takes one cycle per bit of divisor, register array, or data memory, depending on the so both 32-bit/16-bit and 16-bit/16-bit instructions take addressing mode of the instruction. Likewise, output the same number of cycles to execute. data from the ALU can be written to the W register array or a data memory location. 3.3.3 MULTI-BIT SHIFT SUPPORT The PIC24F CPU incorporates hardware support for The PIC24F ALU supports both single bit and both multiplication and division. This includes a single-cycle, multi-bit arithmetic and logic shifts. dedicated hardware multiplier and support hardware Multi-bit shifts are implemented using a shifter block, for 16-bit divisor division. capable of performing up to a 15-bit arithmetic right 3.3.1 MULTIPLIER shift, or up to a 15-bit left shift, in a single cycle. All multi-bit shift instructions only support Register Direct The ALU contains a high-speed, 17-bit x 17-bit Addressing for both the operand source and result multiplier. It supports unsigned, signed or mixed sign destination. operation in several multiplication modes: A full summary of instructions that use the shift 1. 16-bit x 16-bit signed operation is provided below in Table3-2. 2. 16-bit x 16-bit unsigned 3. 16-bit signed x 5-bit (literal) unsigned 4. 16-bit unsigned x 16-bit unsigned 5. 16-bit unsigned x 5-bit (literal) unsigned 6. 16-bit unsigned x 16-bit signed 7. 8-bit unsigned x 8-bit unsigned TABLE 3-2: INSTRUCTIONS THAT USE THE SINGLE AND MULTI-BIT SHIFT OPERATION Instruction Description ASR Arithmetic shift right source register by one or more bits. SL Shift left source register by one or more bits. LSR Logical shift right source register by one or more bits. DS39905E-page 34  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 4.0 MEMORY ORGANIZATION from either the 23-bit Program Counter (PC) during pro- gram execution, or from table operation or data space As Harvard architecture devices, PIC24F micro- remapping, as described in Section4.3 “Interfacing controllers feature separate program and data memory Program and Data Memory Spaces”. spaces and busses. This architecture also allows the User access to the program memory space is restricted direct access of program memory from the data space to the lower half of the address range (000000h to during code execution. 7FFFFFh). The exception is the use of TBLRD/TBLWT operations which use TBLPAG<7> to permit access to 4.1 Program Address Space the Configuration bits and Device ID sections of the The program address memory space of the configuration memory space. PIC24FJ256GA110 family devices is 4M instructions. Memory maps for the PIC24FJ256GA110 family of The space is addressable by a 24-bit value derived devices are shown in Figure4-1. FIGURE 4-1: PROGRAM SPACE MEMORY MAP FOR PIC24FJ256GA110 FAMILY DEVICES PIC24FJ64GA1XX PIC24FJ128GA1XX PIC24FJ192GA1XX PIC24FJ256GA1XX GOTO Instruction GOTO Instruction GOTO Instruction GOTO Instruction 000000h 000002h Reset Address Reset Address Reset Address Reset Address 000004h Interrupt Vector Table Interrupt Vector Table Interrupt Vector Table Interrupt Vector Table 0000FEh Reserved Reserved Reserved Reserved 000100h 000104h Alternate Vector Table Alternate Vector Table Alternate Vector Table Alternate Vector Table 0001FEh User Flash 000200h Program Memory User Flash (22K instructions) Program Memory User Flash Flash Config Words (44K instructions) Program Memory 00ABFEh (67K instructions) User Flash 00AC00h Program Memory e ac Flash Config Words (87K instructions) 0157FEh p S 015800h y or m e Flash Config Words 020BFEh M er 020C00h s U Flash Config Words 02ABFEh Unimplemented Unimplemented 02AC00h Read ‘0’ Read ‘0’ Unimplemented Read ‘0’ Unimplemented Read ‘0’ 7FFFFFh 800000h Reserved Reserved Reserved Reserved e c a p S y F7FFFEh or F80000h m Device Config Registers Device Config Registers Device Config Registers Device Config Registers e F8000Eh M n F80010h o ati ur nfig Reserved Reserved Reserved Reserved o C FEFFFEh FF0000h DEVID (2) DEVID (2) DEVID (2) DEVID (2) FFFFFFh Note: Memory areas are not shown to scale.  2010 Microchip Technology Inc. DS39905E-page 35

PIC24FJ256GA110 FAMILY 4.1.1 PROGRAM MEMORY 4.1.3 FLASH CONFIGURATION WORDS ORGANIZATION In PIC24FJ256GA110 family devices, the top three The program memory space is organized in words of on-chip program memory are reserved for word-addressable blocks. Although it is treated as configuration information. On device Reset, the 24bits wide, it is more appropriate to think of each configuration information is copied into the appropriate address of the program memory as a lower and upper Configuration registers. The addresses of the Flash word, with the upper byte of the upper word being Configuration Word for devices in the unimplemented. The lower word always has an even PIC24FJ256GA110 family are shown in Table4-1. address, while the upper word has an odd address Their location in the memory map is shown with the (Figure4-2). other memory vectors in Figure4-1. Program memory addresses are always word-aligned The Configuration Words in program memory are a on the lower word and addresses are incremented or compact format. The actual Configuration bits are decremented by two during code execution. This mapped in several different registers in the configuration arrangement also provides compatibility with data memory space. Their order in the Flash Configuration memory space addressing and makes it possible to Words do not reflect a corresponding arrangement in the access data in the program memory space. configuration space. Additional details on the device Configuration Words are provided in Section25.1 4.1.2 HARD MEMORY VECTORS “Configuration Bits”. All PIC24F devices reserve the addresses between TABLE 4-1: FLASH CONFIGURATION 00000h and 000200h for hard coded program execu- tion vectors. A hardware Reset vector is provided to WORDS FOR redirect code execution from the default value of the PIC24FJ256GA110 FAMILY PC on device Reset to the actual start of code. A GOTO DEVICES instruction is programmed by the user at 000000h with Program Configuration the actual address for the start of code at 000002h. Device Memory Word PIC24F devices also have two interrupt vector tables, (Words) Addresses located from 000004h to 0000FFh and 000100h to 00ABFEh: 0001FFh. These vector tables allow each of the many PIC24FJ64GA 22,016 00AC00h device interrupt sources to be handled by separate ISRs. A more detailed discussion of the interrupt vector 0157FAh: PIC24FJ128GA 44,032 tables is provided in Section7.1 “Interrupt Vector 0157FEh Table”. 020BFAh: PIC24FJ192GA 67,072 020BFEh 02ABFAh: PIC24FJ256GA 87,552 02ABFEh FIGURE 4-2: PROGRAM MEMORY ORGANIZATION msw most significant word least significant word PC Address Address (lsw Address) 23 16 8 0 000001h 00000000 000000h 000003h 00000000 000002h 000005h 00000000 000004h 000007h 00000000 000006h Program Memory Instruction Width ‘Phantom’ Byte (read as ‘0’) DS39905E-page 36  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 4.2 Data Address Space PIC24FJ256GA110 family devices implement a total of 16Kbytes of data memory. Should an EA point to a The PIC24F core has a separate, 16-bit wide data mem- location outside of this area, an all zero word or byte will ory space, addressable as a single linear range. The be returned. data space is accessed using two Address Generation Units (AGUs), one each for read and write operations. 4.2.1 DATA SPACE WIDTH The data space memory map is shown in Figure4-3. The data memory space is organized in All Effective Addresses (EAs) in the data memory space byte-addressable, 16-bit wide blocks. Data is aligned are 16 bits wide and point to bytes within the data space. in data memory and registers as 16-bit words, but all This gives a data space address range of 64Kbytes or data space EAs resolve to bytes. The Least Significant 32Kwords. The lower half of the data memory space Bytes (LSBs) of each word have even addresses, while (that is, when EA<15> = 0) is used for implemented the Most Significant Bytes (MSBs) have odd memory addresses, while the upper half (EA<15> = 1) is addresses. reserved for the program space visibility area (see Section4.3.3 “Reading Data From Program Memory Using Program Space Visibility”). FIGURE 4-3: DATA SPACE MEMORY MAP FOR PIC24FJ256GA110 FAMILY DEVICES MSB LSB Address MSB LSB Address 0001h 0000h SFR SFR Space 07FFh 07FEh Space Near 0801h 0800h DataSpace 1FFFh 1FFEh 2001h 2000h Implemented Data RAM Data RAM 47FFh 47FEh 4801h 4800h Unimplemented Read as ‘0’ 7FFFh 7FFFh 8001h 8000h Program Space Visibility Area FFFFh FFFEh Note: Data memory areas are not shown to scale.  2010 Microchip Technology Inc. DS39905E-page 37

PIC24FJ256GA110 FAMILY 4.2.2 DATA MEMORY ORGANIZATION A Sign-Extend (SE) instruction is provided to allow AND ALIGNMENT users to translate 8-bit signed data to 16-bit signed values. Alternatively, for 16-bit unsigned data, users To maintain backward compatibility with PIC® devices can clear the MSB of any W register by executing a and improve data space memory usage efficiency, the Zero-Extend (ZE) instruction on the appropriate PIC24F instruction set supports both word and byte address. operations. As a consequence of byte accessibility, all Effective Address (EA) calculations are internally scaled Although most instructions are capable of operating on to step through word-aligned memory. For example, the word or byte data sizes, it should be noted that some core recognizes that Post-Modified Register Indirect instructions operate only on words. Addressing mode [Ws++] will result in a value of Ws + 1 4.2.3 NEAR DATA SPACE for byte operations and Ws + 2 for word operations. The 8-Kbyte area between 0000h and 1FFFh is Data byte reads will read the complete word which con- referred to as the near data space. Locations in this tains the byte, using the LSb of any EA to determine space are directly addressable via a 13-bit absolute which byte to select. The selected byte is placed onto address field within all memory direct instructions. The the LSB of the data path. That is, data memory and reg- remainder of the data space is indirectly addressable. isters are organized as two parallel, byte-wide entities Additionally, the whole data space is addressable using with shared (word) address decode, but separate write lines. Data byte writes only write to the corresponding MOV instructions, which support Memory Direct Addressing with a 16-bit address field. side of the array or register which matches the byte address. 4.2.4 SFR SPACE All word accesses must be aligned to an even address. The first 2Kbytes of the near data space, from 0000h Misaligned word data fetches are not supported, so to 07FFh, are primarily occupied with Special Function care must be taken when mixing byte and word opera- Registers (SFRs). These are used by the PIC24F core tions or translating from 8-bit MCU code. If a and peripheral modules for controlling the operation of misaligned read or write is attempted, an address error the device. trap will be generated. If the error occurred on a read, the instruction underway is completed; if it occurred on SFRs are distributed among the modules that they con- a write, the instruction will be executed but the write will trol and are generally grouped together by module. not occur. In either case, a trap is then executed, allow- Much of the SFR space contains unused addresses; ing the system and/or user to examine the machine these are read as ‘0’. A diagram of the SFR space, state prior to execution of the address Fault. showing where SFRs are actually implemented, is shown in Table4-2. Each implemented area indicates All byte loads into any W register are loaded into the a 32-byte region where at least one address is Least Significant Byte. The Most Significant Byte is not implemented as an SFR. A complete listing of modified. implemented SFRs, including their addresses, is shown in Tables4-3 through4-29. TABLE 4-2: IMPLEMENTED REGIONS OF SFR DATA SPACE SFR Space Address xx00 xx20 xx40 xx60 xx80 xxA0 xxC0 xxE0 000h Core ICN Interrupts — 100h Timers Capture Compare 200h I2C™ UART SPI/UART SPI/I2C SPI UART I/O 300h A/D A/D/CTMU — — — — — — 400h — — — — — — 500h — — — — — — — — 600h PMP RTC/Comp CRC — PPS — 700h — — System NVM/PMD — — — — Legend: — = No implemented SFRs in this block DS39905E-page 38  2010 Microchip Technology Inc.

 TABLE 4-3: CPU CORE REGISTERS MAP 2 010 M NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts icro WREG0 0000 Working Register 0 0000 ch WREG1 0002 Working Register 1 0000 ip T WREG2 0004 Working Register 2 0000 e ch WREG3 0006 Working Register 3 0000 n o WREG4 0008 Working Register 4 0000 lo gy WREG5 000A Working Register 5 0000 In WREG6 000C Working Register 6 0000 c . WREG7 000E Working Register 7 0000 WREG8 0010 Working Register 8 0000 WREG9 0012 Working Register 9 0000 WREG10 0014 Working Register 10 0000 WREG11 0016 Working Register 11 0000 WREG12 0018 Working Register 12 0000 P WREG13 001A Working Register 13 0000 I WREG14 001C Working Register 14 0000 C WREG15 001E Working Register 15 0800 2 SPLIM 0020 Stack Pointer Limit Value Register xxxx 4 PCL 002E Program Counter Low Word Register 0000 F PCH 0030 — — — — — — — — Program Counter Register High Byte 0000 J TBLPAG 0032 — — — — — — — — Table Memory Page Address Register 0000 2 PSVPAG 0034 — — — — — — — — Program Space Visibility Page Address Register 0000 5 RCOUNT 0036 Repeat Loop Counter Register xxxx 6 SR 0042 — — — — — — — DC IPL2 IPL1 IPL0 RA N OV Z C 0000 G CORCON 0044 — — — — — — — — — — — — IPL3 PSV — — 0000 DISICNT 0052 — — Disable Interrupts Counter Register xxxx A Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. 1 1 0 F D A S 3 99 M 0 5 E -pa IL g e 3 Y 9

D TABLE 4-4: ICN REGISTER MAP P S 3 9 File All I 9 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 C 0 Name Resets 5 E -p CNPD1 0054 CN15PDE CN14PDE CN13PDE CN12PDE CN11PDE CN10PDE CN9PDE CN8PDE CN7PDE CN6PDE CN5PDE CN4PDE CN3PDE CN2PDE CN1PDE CN0PDE 0000 2 a ge CNPD2 0056 CN31PDE CN30PDE CN29PDE CN28PDE CN27PDE CN26PDE CN25PDE CN24PDE CN23PDE CN22PDE CN21PDE(1) CN20PDE(1) CN19PDE(1) CN18PDE CN17PDE CN16PDE 0000 4 40 CNPD3 0058 CN47PDE(1) CN46PDE(2) CN45PDE(1) CN44PDE(1) CN43PDE(1) CN42PDE(1) CN41PDE(1) CN40PDE(2)CN39PDE(2) CN38PDE(2) CN37PDE(2) CN36PDE(2) CN35PDE(2) CN34PDE(2) CN33PDE(2) CN32PDE 0000 F CNPD4 005A CN63PDE CN62PDE CN61PDE CN60PDE CN59PDE CN58PDE CN57PDE(1) CN56PDE CN55PDE CN54PDE CN53PDE CN52PDE CN51PDE CN50PDE CN49PDE CN48PDE(2) 0000 J CNPD5 005C CN79PDE(2) CN78PDE(1) CN77PDE(1) CN76PDE(2) CN75PDE(2) CN74PDE(1) CN73PDE(1) CN72PDE CN71PDE CN70PDE CN69PDE CN68PDE CN67PDE(1) CN66PDE(1) CN65PDE CN64PDE 0000 2 CNPD6 005E — — — — — — — — — — — CN84PDE CN83PDE CN82PDE(2) CN81PDE(2) CN80PDE(2) 0000 5 CNEN1 0060 CN15IE CN14IE CN13IE CN12IE CN11IE CN10IE CN9IE CN8IE CN7IE CN6IE CN5IE CN4IE CN3IE CN2IE CN1IE CN0IE 0000 6 CNEN2 0062 CN31IE CN30IE CN29IE CN28IE CN27IE CN26IE CN25IE CN24IE CN23IE CN22IE CN21IE(1) CN20IE(1) CN19IE(1) CN18IE CN17IE CN16IE 0000 G CNEN3 0064 CN47IE(1) CN46IE(2) CN45IE(1) CN44IE(1) CN43IE(1) CN42IE(1) CN41IE(1) CN40IE(2) CN39IE(2) CN38IE(2) CN37IE(2) CN36IE(2) CN35IE(2) CN34IE(2) CN33IE(2) CN32IE 0000 A CNEN4 0066 CN63IE CN62IE CN61IE CN60IE CN59IE CN58IE CN57IE(1) CN56IE CN55IE CN54IE CN53IE CN52IE CN51IE CN50IE CN49IE CN48IE(2) 0000 CNEN5 0068 CN79IE(2) CN78IE(1) CN77IE(1) CN76IE(2) CN75IE(2) CN74IE(1) CN73IE(1) CN72IE CN71IE CN70IE CN69IE CN68IE CN67IE(1) CN66IE(1) CN65IE CN64IE 0000 1 CNEN6 006A — — — — — — — — — — — CN84IE CN83IE CN82IE(2) CN81IE(2) CN80IE(2) 0000 1 0 CNPU1 006C CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE 0000 CNPU2 006E CN31PUE CN30PUE CN29PUE CN28PUE CN27PUE CN26PUE CN25PUE CN24PUE CN23PUE CN22PUE CN21PUE(1) CN20PUE(1) CN19PUE(1) CN18PUE CN17PUE CN16PUE 0000 F CNPU3 0070 CN47PUE(1) CN46PUE(2) CN45PUE(1) CN44PUE(1) CN43PUE(1) CN42PUE(1) CN41PUE(1) CN40PUE(2)CN39PUE(2) CN38PUE(2) CN37PUE(2) CN36PUE(2) CN35PUE(2) CN34PUE(2) CN33PUE(2) CN32PUE 0000 A CNPU4 0072 CN63PUE CN62PUE CN61PUE CN60PUE CN59PUE CN58PUE CN57PUE(1) CN56PUE CN55PUE CN54PUE CN53PUE CN52PUE CN51PUE CN50PUE CN49PUE CN48PUE(2) 0000 CNPU5 0074 CN79PUE(2) CN78PUE(1) CN77PUE(1) CN76PUE(2) CN75PUE(2) CN74PUE(1) CN73PUE(1) CN72PUE CN71PUE CN70PUE CN69PUE CN68PUE CN67PUE(1) CN66PUE(1) CN65PUE CN64PUE 0000 M CNPU6 0076 — — — — — — — — — — — CN84PUE CN83PUE CN82PUE(2) CN81PUE(2) CN80PUE(2) 0000 I L Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Note 1: Unimplemented in 64-pin devices; read as ‘0’. Y 2: Unimplemented in 64-pin and 80-pin devices; read as ‘0’.  2 0 1 0 M ic ro c h ip T e c h n o lo g y In c .

 TABLE 4-5: INTERRUPT CONTROLLER REGISTER MAP 2 0 File All 1 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 Name Resets M ic INTCON1 0080 NSTDIS — — — — — — — — — — MATHERR ADDRERR STKERR OSCFAIL — 0000 ro c INTCON2 0082 ALTIVT DISI — — — — — — — — — INT4EP INT3EP INT2EP INT1EP INT0EP 0000 h ip IFS0 0084 — — AD1IF U1TXIF U1RXIF SPI1IF SPF1IF T3IF T2IF OC2IF IC2IF — T1IF OC1IF IC1IF INT0IF 0000 T e IFS1 0086 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF — IC8IF IC7IF — INT1IF CNIF CMIF MI2C1IF SI2C1IF 0000 c hn IFS2 0088 — — PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF IC5IF IC4IF IC3IF — — — SPI2IF SPF2IF 0000 o lo IFS3 008A — RTCIF — — — — — — — INT4IF INT3IF — — MI2C2IF SI2C2IF — 0000 g y IFS4 008C — — CTMUIF — — — — LVDIF — — — — CRCIF U2ERIF U1ERIF — 0000 Inc IFS5 008E — — IC9IF OC9IF SPI3IF SPF3IF U4TXIF U4RXIF U4ERIF — MI2C3IF SI2C3IF U3TXIF U3RXIF U3ERIF — 0000 . IEC0 0094 — — AD1IE U1TXIE U1RXIE SPI1IE SPF1IE T3IE T2IE OC2IE IC2IE — T1IE OC1IE IC1IE INT0IE 0000 IEC1 0096 U2TXIE U2RXIE INT2IE T5IE T4IE OC4IE OC3IE — IC8IE IC7IE — INT1IE CNIE CMIE MI2C1IE SI2C1IE 0000 IEC2 0098 — — PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE IC5IE IC4IE IC3IE — — — SPI2IE SPF2IE 0000 IEC3 009A — RTCIE — — — — — — — INT4IE INT3IE — — MI2C2IE SI2C2IE — 0000 IEC4 009C — — CTMUIE — — — — LVDIE — — — — CRCIE U2ERIE U1ERIE — 0000 IEC5 009E — — IC9IE OC9IE SPI3IE SPF3IE U4TXIE U4RXIE U4ERIE — MI2C3IE SI2C3IE U3TXIE U3RXIE U3ERIE — 0000 IPC0 00A4 — T1IP2 T1IP1 T1IP0 — OC1IP2 OC1IP1 OC1IP0 — IC1IP2 IC1IP1 IC1IP0 — INT0IP2 INT0IP1 INT0IP0 4444 P IPC1 00A6 — T2IP2 T2IP1 T2IP0 — OC2IP2 OC2IP1 OC2IP0 — IC2IP2 IC2IP1 IC2IP0 — — — — 4440 I IPC2 00A8 — U1RXIP2 U1RXIP1 U1RXIP0 — SPI1IP2 SPI1IP1 SPI1IP0 — SPF1IP2 SPF1IP1 SPF1IP0 — T3IP2 T3IP1 T3IP0 4444 C IPC3 00AA — — — — — — — — — AD1IP2 AD1IP1 AD1IP0 — U1TXIP2 U1TXIP1 U1TXIP0 0044 2 IPC4 00AC — CNIP2 CNIP1 CNIP0 — CMIP2 CMIP1 CMIP0 — MI2C1IP2 MI2C1IP1 MI2C1IP0 — SI2C1IP2 SI2C1IP1 SI2C1IP0 4444 4 IPC5 00AE — IC8IP2 IC8IP1 IC8IP0 — IC7IP2 IC7IP1 IC7IP0 — — — — — INT1IP2 INT1IP1 INT1IP0 4404 F IPC6 00B0 — T4IP2 T4IP1 T4IP0 — OC4IP2 OC4IP1 OC4IP0 — OC3IP2 OC3IP1 OC3IP0 — — — — 4440 J IPC7 00B2 — U2TXIP2 U2TXIP1 U2TXIP0 — U2RXIP2 U2RXIP1 U2RXIP0 — INT2IP2 INT2IP1 INT2IP0 — T5IP2 T5IP1 T5IP0 4444 IPC8 00B4 — — — — — — — — — SPI2IP2 SPI2IP1 SPI2IP0 — SPF2IP2 SPF2IP1 SPF2IP0 0044 2 IPC9 00B6 — IC5IP2 IC5IP1 IC5IP0 — IC4IP2 IC4IP1 IC4IP0 — IC3IP2 IC3IP1 IC3IP0 — — — — 4440 5 IPC10 00B8 — OC7IP2 OC7IP1 OC7IP0 — OC6IP2 OC6IP1 OC6IP0 — OC5IP2 OC5IP1 OC5IP0 — IC6IP2 IC6IP1 IC6IP0 4444 6 IPC11 00BA — — — — — — — — — PMPIP2 PMPIP1 PMPIP0 — OC8IP2 OC8IP1 OC8IP0 0044 G IPC12 00BC — — — — — MI2C2IP2 MI2C2IP1 MI2C2IP0 — SI2C2IP2 SI2C2IP1 SI2C2IP0 — — — — 0440 A IPC13 00BE — — — — — INT4IP2 INT4IP1 INT4IP0 — INT3IP2 INT3IP1 INT3IP0 — — — — 0440 IPC15 00C2 — — — — — RTCIP2 RTCIP1 RTCIP0 — — — — — — — — 0400 1 IPC16 00C4 — CRCIP2 CRCIP1 CRCIP0 — U2ERIP2 U2ERIP1 U2ERIP0 — U1ERIP2 U1ERIP1 U1ERIP0 — — — — 4440 1 IPC18 00C8 — — — — — — — — — — — — — LVDIP2 LVDIP1 LVDIP0 0004 0 IPC19 00CA — — — — — — — — — CTMUIP2 CTMUIP1 CTMUIP0 — — — — 0040 IPC20 00CC — U3TXIP2 U3TXIP1 U3TXIP0 — U3RXIP2 U3RXIP1 U3RXIP0 — U3ERIP2 U3ERIP1 U3ERIP0 — — — — 4440 F D IPC21 00CE — U4ERIP2 U4ERIP1 U4ERIP0 — — — — — MI2C3IP2 MI2C3IP1 MI2C3IP0 — SI2C3IP2 SI2C3IP1 SI2C3IP0 4044 A S 399 IPC22 00D0 — SPI3IP2 SPI3IP1 SPI3IP0 — SPF3IP2 SPF3IP1 SPF3IP0 — U4TXIP2 U4TXIP1 U4TXIP0 — U4RXIP2 U4RXIP1 U4RXIP0 4444 M 0 IPC23 00D2 — — — — — — — — — IC9IP2 IC9IP1 IC9IP0 — OC9IP2 OC9IP1 OC9IP0 0044 5 E-pa ILNeTgTeRnEdG: 00—E0 = uCnPimUpIRleQmented—, read aVs H‘0O’. LRDeset va—lues are sIhLoRw3n in heILxaRd2ecimal.ILR1 ILR0 — VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000 IL g e 4 Y 1

D TABLE 4-6: TIMER REGISTER MAP P S 3 9 All I 90 File Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Resets C 5 E -p TMR1 0100 Timer1 Register 0000 2 a g PR1 0102 Timer1 Period Register FFFF 4 e 4 T1CON 0104 TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 — TSYNC TCS — 0000 F 2 TMR2 0106 Timer2 Register 0000 J TMR3HLD 0108 Timer3 Holding Register (for 32-bit timer operations only) 0000 2 TMR3 010A Timer3 Register 0000 5 PR2 010C Timer2 Period Register FFFF 6 PR3 010E Timer3 Period Register FFFF G T2CON 0110 TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 T32 — TCS — 0000 A T3CON 0112 TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 — — TCS — 0000 TMR4 0114 Timer4 Register 0000 1 TMR5HLD 0116 Timer5 Holding Register (for 32-bit operations only) 0000 1 TMR5 0118 Timer5 Register 0000 0 PR4 011A Timer4 Period Register FFFF F PR5 011C Timer5 Period Register FFFF A T4CON 011E TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 T32 — TCS — 0000 T5CON 0120 TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 — — TCS — 0000 M Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. I L Y  2 0 1 0 M ic ro c h ip T e c h n o lo g y In c .

 TABLE 4-7: INPUT CAPTURE REGISTER MAP 2 010 M NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts icro IC1CON1 0140 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 ch IC1CON2 0142 — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D ip T IC1BUF 0144 Input Capture 1 Buffer Register 0000 ec IC1TMR 0146 Timer Value 1 Register xxxx h no IC2CON1 0148 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 log IC2CON2 014A — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D y In IC2BUF 014C Input Capture 2 Buffer Register 0000 c . IC2TMR 014E Timer Value 2 Register xxxx IC3CON1 0150 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 IC3CON2 0152 — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D IC3BUF 0154 Input Capture 3 Buffer Register 0000 IC3TMR 0156 Timer Value 3 Register xxxx IC4CON1 0158 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 IC4CON2 015A — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D P IC4BUF 015C Input Capture 4 Buffer Register 0000 I IC4TMR 015E Timer Value 4 Register xxxx C IC5CON1 0160 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 2 IC5CON2 0162 — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D 4 IC5BUF 0164 Input Capture 5 Buffer Register 0000 F IC5TMR 0166 Timer Value 5 Register xxxx J IC6CON1 0168 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 2 IC6CON2 016A — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D 5 IC6BUF 016C Input Capture 6 Buffer Register 0000 IC6TMR 016E Timer Value 6 Register xxxx 6 IC7CON1 0170 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 G IC7CON2 0172 — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D A IC7BUF 0174 Input Capture 7 Buffer Register 0000 1 IC7TMR 0176 Timer Value 7 Register xxxx 1 IC8CON1 0178 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 0 IC8CON2 017A — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D IC8BUF 017C Input Capture 8 Buffer Register 0000 F D IC8TMR 017E Timer Value 8 Register xxxx A S 3 IC9CON1 0180 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 99 IC9CON2 0182 — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D M 0 5E IC9BUF 0184 Input Capture 9 Buffer Register 0000 -pa IC9TMR 0186 Timer Value 9 Register xxxx IL g e 4 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Y 3

D TABLE 4-8: OUTPUT COMPARE REGISTER MAP P S 3 9 File All I 9 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 C 0 Name Resets 5 E -p OC1CON1 0190 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 2 a g OC1CON2 0192 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C 4 e 4 OC1RS 0194 Output Compare 1 Secondary Register 0000 F 4 OC1R 0196 Output Compare 1 Register 0000 J OC1TMR 0198 Timer Value 1 Register xxxx 2 OC2CON1 019A — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 5 OC2CON2 019C FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C 6 OC2RS 019E Output Compare 2 Secondary Register 0000 G OC2R 01A0 Output Compare 2 Register 0000 OC2TMR 01A2 Timer Value 2 Register xxxx A OC3CON1 01A4 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 1 OC3CON2 01A6 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C 1 OC3RS 01A8 Output Compare 3 Secondary Register 0000 0 OC3R 01AA Output Compare 3 Register 0000 OC3TMR 01AC Timer Value 3 Register xxxx F OC4CON1 01AE — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 A OC4CON2 01B0 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C M OC4RS 01B2 Output Compare 4 Secondary Register 0000 OC4R 01B4 Output Compare 4 Register 0000 I L OC4TMR 01B6 Timer Value 4 Register xxxx Y OC5CON1 01B8 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 OC5CON2 01BA FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C OC5RS 01BC Output Compare 5 Secondary Register 0000 OC5R 01BE Output Compare 5 Register 0000 OC5TMR 01C0 Timer Value 5 Register xxxx OC6CON1 01C2 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 OC6CON2 01C4 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C  OC6RS 01C6 Output Compare 6 Secondary Register 0000 2 0 OC6R 01C8 Output Compare 6 Register 0000 1 0 M OC6TMR 01CA Timer Value 6 Register xxxx ic OC7CON1 01CC — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 ro c OC7CON2 01CE FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C h ip T OC7RS 01D0 Output Compare 7 Secondary Register 0000 ec OC7R 01D2 Output Compare 7 Register 0000 h n OC7TMR 01D4 Timer Value 7 Register xxxx o log Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. y In c .

 TABLE 4-8: OUTPUT COMPARE REGISTER MAP (CONTINUED) 2 010 M NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts icro OC8CON1 01D6 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 ch OC8CON2 01D8 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C ip T OC8RS 01DA Output Compare 8 Secondary Register 0000 e c OC8R 01DC Output Compare 8 Register 0000 h no OC8TMR 01DE Timer Value 8 Register xxxx lo g OC9CON1 01E0 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — ENFLT0 — — OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 y In OC9CON2 01E2 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C c . OC9RS 01E4 Output Compare 9 Secondary Register 0000 OC9R 01E6 Output Compare 9 Register 0000 OC9TMR 01E8 Timer Value 9 Register xxxx Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-9: I2C˜ REGISTER MAP P File All I Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 C Name Resets I2C1RCV 0200 — — — — — — — — Receive Register 0000 2 I2C1TRN 0202 — — — — — — — — Transmit Register 00FF 4 I2C1BRG 0204 — — — — — — — Baud Rate Generator Register 0000 F I2C1CON 0206 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN 1000 J I2C1STAT 0208 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D/A P S R/W RBF TBF 0000 2 I2C1ADD 020A — — — — — — Address Register 0000 5 I2C1MSK 020C — — — — — — Address Mask Register 0000 6 I2C2RCV 0210 — — — — — — — — Receive Register 0000 G I2C2TRN 0212 — — — — — — — — Transmit Register 00FF I2C2BRG 0214 — — — — — — — Baud Rate Generator Register 0000 A I2C2CON 0216 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN 1000 1 I2C2STAT 0218 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D/A P S R/W RBF TBF 0000 1 I2C2ADD 021A — — — — — — Address Register 0000 0 I2C2MSK 021C — — — — — — Address Mask Register 0000 I2C3RCV 0270 — — — — — — — — Receive Register 0000 F I2C3TRN 0272 — — — — — — — — Transmit Register 00FF D A S I2C3BRG 0274 — — — — — — — Baud Rate Generator Register 0000 3 99 I2C3CON 0276 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN 1000 M 0 5E I2C3STAT 0278 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D/A P S R/W RBF TBF 0000 -pa I2C3ADD 027A — — — — — — Address Register 0000 IL ge 45 IL2eCg3eMnSd:K 0—27 C= unimpl—emented, rea—d as ‘0’. Re—set values —are shown —in hexadeci—mal. Address Mask Register 0000 Y

D TABLE 4-10: UART REGISTER MAP P S 3 990 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts IC 5 E-p U1MODE 0220 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL 0000 2 ag U1STA 0222 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA 0110 4 e 4 U1TXREG 0224 — — — — — — — Transmit Register xxxx F 6 U1RXREG 0226 — — — — — — — Receive Register 0000 J U1BRG 0228 Baud Rate Generator Prescaler 0000 2 U2MODE 0230 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL 0000 5 U2STA 0232 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA 0110 U2TXREG 0234 — — — — — — — Transmit Register xxxx 6 U2RXREG 0236 — — — — — — — Receive Register 0000 G U2BRG 0238 Baud Rate Generator Prescaler 0000 A U3MODE 0250 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL 0000 U3STA 0252 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA 0110 1 U3TXREG 0254 — — — — — — — Transmit Register xxxx 1 U3RXREG 0256 — — — — — — — Receive Register 0000 0 U3BRG 0258 Baud Rate Generator Prescaler 0000 F U4MODE 02B0 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL 0000 U4STA 02B2 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA 0110 A U4TXREG 02B4 — — — — — — — Transmit Register xxxx M U4RXREG 02B6 — — — — — — — Receive Register 0000 U4BRG 02B8 Baud Rate Generator Prescaler 0000 I L Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Y TABLE 4-11: SPI REGISTER MAP File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets SPI1STAT 0240 SPIEN — SPISIDL — — SPIBEC2 SPIBEC1 SPIBEC0 SRMPT SPIROV SRXMPT SISEL2 SISEL1 SISEL0 SPITBF SPIRBF 0000 SPI1CON1 0242 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE2 SPRE1 SPRE0 PPRE1 PPRE0 0000 SPI1CON2 0244 FRMEN SPIFSD SPIFPOL — — — — — — — — — — — SPIFE SPIBEN 0000  2 SPI1BUF 0248 Transmit and Receive Buffer 0000 0 1 SPI2STAT 0260 SPIEN — SPISIDL — — SPIBEC2 SPIBEC1 SPIBEC0 SRMPT SPIROV SRXMPT SISEL2 SISEL1 SISEL0 SPITBF SPIRBF 0000 0 M SPI2CON1 0262 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE2 SPRE1 SPRE0 PPRE1 PPRE0 0000 icro SPI2CON2 0264 FRMEN SPIFSD SPIFPOL — — — — — — — — — — — SPIFE SPIBEN 0000 ch SPI2BUF 0268 Transmit and Receive Buffer 0000 ip T SPI3STAT 0280 SPIEN — SPISIDL — — SPIBEC2 SPIBEC1 SPIBEC0 SRMPT SPIROV SRXMPT SISEL2 SISEL1 SISEL0 SPITBF SPIRBF 0000 ec SPI3CON1 0282 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE2 SPRE1 SPRE0 PPRE1 PPRE0 0000 h no SPI3CON2 0284 FRMEN SPIFSD SPIFPOL — — — — — — — — — — — SPIFE SPIBEN 0000 log SPI3BUF 0288 Transmit and Receive Buffer 0000 y In Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. c .

 TABLE 4-12: PORTA REGISTER MAP(1) 2 01 File Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7(2) Bit 6(2) Bit 5(2) Bit 4(2) Bit 3(2) Bit2(2) Bit 1(2) Bit 0(2) All 0 Name Resets M ic TRISA 02C0 TRISA15 TRISA14 — — — TRISA10 TRISA9 — TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 36FF roc PORTA 02C2 RA15 RA14 — — — RA10 RA9 — RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 xxxx h ip LATA 02C4 LATA15 LATA14 — — — LATA10 LATA9 — LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 xxxx T e ODCA 02C6 ODA15 ODA14 — — — ODA10 ODA9 — ODA7 ODA6 ODA5 ODA4 ODA3 ODA2 ODA1 ODA0 0000 c hn Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Reset values shown are for 100-pin devices. olo Note 1: PORTA and all associated bits are unimplemented on 64-pin devices and read as ‘0’. Bits are available on 80-pin and 100-pin devices only, unless otherwise noted. g 2: Bits are implemented on 100-pin devices only; otherwise, read as ‘0’. y In c . TABLE 4-13: PORTB REGISTER MAP File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets TRISB 02C8 TRISB15 TRISB14 TRISB13 TRISB12 TRISB11 TRISB10 TRISB9 TRISB8 TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 FFFF PORTB 02CA RB15 RB14 RB13 RB12 RB11 RB10 RB9 RB8 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx LATB 02CC LATB15 LATB14 LATB13 LATB12 LATB11 LATB10 LATB9 LATB8 LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 xxxx P ODCB 02CE ODB15 ODB14 ODB13 ODB12 ODB11 ODB10 ODB9 ODB8 ODB7 ODB6 ODB5 ODB4 ODB3 ODB2 ODB1 ODB0 0000 I Legend: Reset values are shown in hexadecimal. C 2 TABLE 4-14: PORTC REGISTER MAP 4 File Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4(1) Bit 3(2) Bit 2(1) Bit 1(2) Bit 0 All F Name Resets J TRISC 02D0 TRISC15 TRISC14 TRISC13 TRISC12 — — — — — — — TRISC4 TRISC3 TRISC2 TRISC1 — F01E 2 PORTC 02D2 RC15(3,4) RC14 RC13 RC12(3) — — — — — — — RC4 RC3 RC2 RC1 — xxxx 5 LATC 02D4 LATC15 LATC14 LATC13 LATC12 — — — — — — — LATC4 LATC3 LATC2 LATC1 — xxxx 6 ODCC 02D6 ODC15 ODC14 ODC13 ODC12 — — — — — — — ODC4 ODC3 ODC2 ODC1 — 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Reset values shown are for 100-pin devices. G Note 1: Bits are unimplemented in 64-pin and 80-pin devices; read as ‘0’. 2: Bits are unimplemented in 64-pin devices; read as ‘0’. A 3: RC12 and RC15 are only available when the Primary Oscillator is disabled or when EC mode is selected (POSCMD<1:0> Configuration bits= 11 or 00); otherwise, read as ‘0’ 1 4: RC15 is only available when POSCMD<1:0> Configuration bits= 11 or 00 and the OSCIOFN Configuration bit = 1. 1 0 TABLE 4-15: PORTD REGISTER MAP F File Addr Bit 15(1) Bit 14(1) Bit 13(1) Bit 12(1) Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All D Name Resets A S 3 99 TRISD 02D8 TRISD15 TRISD14 TRISD13 TRISD12 TRISD11 TRISD10 TRISD9 TRISD8 TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 FFFF M 05 PORTD 02DA RD15 RD14 RD13 RD12 RD11 RD10 RD9 RD8 RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 xxxx E -pag LOADTCDD 0022DDCE LOADTDD1155 LOADTDD1144 LOADTDD1133 LOADTDD1122 LOADTDD1111 LOADTDD1100 LOADTDD99 LOADTDD88 LOADTDD77 LOADTDD66 LOADTDD55 LOADTDD44 LOADTDD33 LOADTDD22 LOADTDD11 LOADTDD00 x0x0x0x0 IL e 4 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Reset values shown are for 100-pin devices. Y 7 Note 1: Bits are unimplemented on 64-pin devices; read as ‘0’.

D P S TABLE 4-16: PORTE REGISTER MAP 3 9 I 905 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9(1) Bit 8(1) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts C E -pa TRISE 02E0 — — — — — — TRISE9 TRISE8 TRISE7 TRISE6 TRISE5 TRISE4 TRISE3 TRISE2 TRISE1 TRISE0 03FF 2 g 4 e PORTE 02E2 — — — — — — RE9 RE8 RE7 RE6 RE5 RE4 RE3 RE2 RE1 RE0 xxxx 4 F 8 LATE 02E4 — — — — — — LATE9 LATE8 LATE7 LATE6 LATE5 LATE4 LATE3 LATE2 LATE1 LATE0 xxxx ODCE 02E6 — — — — — — ODE9 ODE8 ODE7 ODE6 ODE5 ODE4 ODE3 ODE2 ODE1 ODE0 0000 J Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Reset values shown are for 100-pin devices. 2 Note 1: Bits are unimplemented in 64-pin devices; read as ‘0’. 5 6 TABLE 4-17: PORTF REGISTER MAP G File Addr Bit 15 Bit 14 Bit 13(1) Bit 12(1) Bit 11 Bit 10 Bit 9 Bit 8(2) Bit 7(2) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All A Name Resets TRISF 02E8 — — TRISF13 TRISF12 — — — TRISF8 TRISF7 TRISF6 TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0 31FF 1 PORTF 02EA — — RF13 RF12 — — — RF8 RF7 RF6 RF5 RF4 RF3 RF2 RF1 RF0 xxxx 1 LATF 02EC — — LATF13 LATF12 — — — LATF8 LATF7 LATF6 LATF5 LATF4 LATF3 LATF2 LATF1 LATF0 xxxx 0 ODCF 02EE — — ODF13 ODF12 — — — ODF8 ODF7 ODF6 ODF5 ODF4 ODF3 ODF2 ODF1 ODF0 0000 F Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Reset values shown are for 100-pin devices. Note 1: Bits are unimplemented in 64-pin and 80-pin devices; read as ‘0’. A 2: Bits are unimplemented in 64-pin devices; read as ‘0’. M TABLE 4-18: PORTG REGISTER MAP I L File Addr Bit 15(1) Bit 14(1) Bit 13(1) Bit 12(1) Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1(2) Bit 0(2) All Y Name Resets TRISG 02F0 TRISG15 TRISG14 TRISG13 TRISG12 — — TRISG9 TRISG8 TRISG7 TRISG6 — — TRISG3 TRISG2 TRISG1 TRISG0 F3CF PORTG 02F2 RG15 RG14 RG13 RG12 — — RG9 RG8 RG7 RG6 — — RG3 RG2 RG1 RG0 xxxx LATG 02F4 LATG15 LATG14 LATG13 LATG12 — — LATG9 LATG8 LATG7 LATG6 — — LATG3 LATG2 LATG1 LATG0 xxxx ODCG 02F6 ODG15 ODG14 ODG13 ODG12 — — ODG9 ODG8 ODG7 ODG6 — — ODG3 ODG2 ODG1 ODG0 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Reset values shown are for 100-pin devices. Note 1: Bits unimplemented in 64-pin and 80-pin devices; read as ‘0’.  2: Bits unimplemented in 64-pin devices; read as ‘0’. 2 0 1 0 M TABLE 4-19: PAD CONFIGURATION REGISTER MAP ic ro File All c Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 h Name Resets ip Te PADCFG1 02FC — — — — — — — — — — — — — — RTSECSEL PMPTTL 0000 c hn Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. o lo g y In c .

 TABLE 4-20: ADC REGISTER MAP 2 0 File All 1 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 Name Resets M ic ADC1BUF0 0300 ADC Data Buffer 0 xxxx ro c ADC1BUF1 0302 ADC Data Buffer 1 xxxx h ip ADC1BUF2 0304 ADC Data Buffer 2 xxxx T e ADC1BUF3 0306 ADC Data Buffer 3 xxxx c hn ADC1BUF4 0308 ADC Data Buffer 4 xxxx o lo ADC1BUF5 030A ADC Data Buffer 5 xxxx g y ADC1BUF6 030C ADC Data Buffer 6 xxxx Inc ADC1BUF7 030E ADC Data Buffer 7 xxxx . ADC1BUF8 0310 ADC Data Buffer 8 xxxx ADC1BUF9 0312 ADC Data Buffer 9 xxxx ADC1BUFA 0314 ADC Data Buffer 10 xxxx ADC1BUFB 0316 ADC Data Buffer 11 xxxx ADC1BUFC 0318 ADC Data Buffer 12 xxxx ADC1BUFD 031A ADC Data Buffer 13 xxxx ADC1BUFE 031C ADC Data Buffer 14 xxxx P ADC1BUFF 031E ADC Data Buffer 15 xxxx I C AD1CON1 0320 ADON — ADSIDL — — — FORM1 FORM0 SSRC2 SSRC1 SSRC0 — — ASAM SAMP DONE 0000 AD1CON2 0322 VCFG2 VCFG1 VCFG0 r — CSCNA — — BUFS — SMPI3 SMPI2 SMPI1 SMPI0 BUFM ALTS 0000 2 AD1CON3 0324 ADRC r r SAMC4 SAMC3 SAMC2 SAMC1 SAMC0 ADCS7 ADCS6 ADCS5 ADCS4 ADCS3 ADCS2 ADCS1 ADCS0 0000 4 AD1CHS 0328 CH0NB — — CH0SB4 CH0SB3 CH0SB2 CH0SB1 CH0SB0 CH0NA — — CH0SA4 CH0SA3 CH0SA2 CH0SA1 CH0SA0 0000 F AD1PCFGL 032C PCFG15 PCFG14 PCFG13 PCFG12 PCFG11 PCFG10 PCFG9 PCFG8 PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 0000 J AD1PCFGH 032A — — — — — — — — — — — — — — PCFG17 PCFG16 0000 2 AD1CSSL 0330 CSSL15 CSSL14 CSSL13 CSSL12 CSSL11 CSSL10 CSSL9 CSSL8 CSSL7 CSSL6 CSSL5 CSSL4 CSSL3 CSSL2 CSSL1 CSSL0 0000 Legend: — = unimplemented, read as ‘0’, r = reserved, maintain as ‘0’. Reset values are shown in hexadecimal. 5 6 G TABLE 4-21: CTMU REGISTER MAP A File All 1 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets 1 CTMUCON 033C CTMUEN — CTMUSIDL TGEN EDGEN EDGSEQEN IDISSEN CTTRIG EDG2POL EDG2SEL1 EDG2SEL0 EDG1POL EDG1SEL1 EDG1SEL0 EDG2STAT EDG1STAT 0000 0 CTMUICON 033E ITRIM5 ITRIM4 ITRIM3 ITRIM2 ITRIM1 ITRIM0 IRNG1 IRNG0 — — — — — — — — 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. F D A S 3 99 M 0 5 E -pa IL g e 4 Y 9

D TABLE 4-22: PARALLEL MASTER/SLAVE PORT REGISTER MAP P S 399 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts IC 0 5 E -p PMCON 0600 PMPEN — PSIDL ADRMUX1 ADRMUX0 PTBEEN PTWREN PTRDEN CSF1 CSF0 ALP CS2P CS1P BEP WRSP RDSP 0000 2 ag PMMODE 0602 BUSY IRQM1 IRQM0 INCM1 INCM0 MODE16 MODE1 MODE0 WAITB1 WAITB0 WAITM3 WAITM2 WAITM1 WAITM0 WAITE1 WAITE0 0000 4 e 5 PMADDR 0604 CS2 CS1 ADDR13 ADDR12 ADDR11 ADDR10 ADDR9 ADDR8 ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 0000 F 0 PMDOUT1 Parallel Port Data Out Register 1 (Buffers 0 and 1) 0000 J PMDOUT2 0606 Parallel Port Data Out Register 2 (Buffers 2 and 3) 0000 2 PMDIN1 0608 Parallel Port Data In Register 1 (Buffers 0 and 1) 0000 5 PMDIN2 060A Parallel Port Data In Register 2 (Buffers 2 and 3) 0000 6 PMAEN 060C PTEN15 PTEN14 PTEN13 PTEN12 PTEN11 PTEN10 PTEN9 PTEN8 PTEN7 PTEN6 PTEN5 PTEN4 PTEN3 PTEN2 PTEN1 PTEN0 0000 G PMSTAT 060E IBF IBOV — — IB3F IB2F IB1F IB0F OBE OBUF — — OB3E OB2E OB1E OB0E 0000 A Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. 1 TABLE 4-23: REAL-TIME CLOCK AND CALENDAR REGISTER MAP 1 File All 0 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets F ALRMVAL 0620 Alarm Value Register Window Based on ALRMPTR<1:0> xxxx A ALCFGRPT 0622 ALRMEN CHIME AMASK3 AMASK2 AMASK1 AMASK0 ALRMPTR1 ALRMPTR0 ARPT7 ARPT6 ARPT5 ARPT4 ARPT3 ARPT2 ARPT1 ARPT0 0000 RTCVAL 0624 RTCC Value Register Window Based on RTCPTR<1:0> xxxx M RCFGCAL 0626 RTCEN — RTCWREN RTCSYNC HALFSEC RTCOE RTCPTR1 RTCPTR0 CAL7 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 xxxx I Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. L TABLE 4-24: COMPARATORS REGISTER MAP Y File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets CMSTAT 0630 CMIDL — — — — C3EVT C2EVT C1EVT — — — — — C3OUT C2OUT C1OUT 0000 CVRCON 0632 — — — — — — — — CVREN CVROE CVRR CVRSS CVR3 CVR2 CVR1 CVR0 0000 CM1CON 0634 CEN COE CPOL — — — CEVT COUT EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 0000 CM2CON 0636 CEN COE CPOL — — — CEVT COUT EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 0000  2 CM3CON 0638 CEN COE CPOL — — — CEVT COUT EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 0000 01 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. 0 M ic TABLE 4-25: CRC REGISTER MAP ro chip NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts T e c CRCCON 0640 — — CSIDL VWORD4 VWORD3 VWORD2 VWORD1 VWORD0 CRCFUL CRCMPT — CRCGO PLEN3 PLEN2 PLEN1 PLEN0 0040 h n o CRCXOR 0642 X15 X14 X13 X12 X11 X10 X9 X8 X7 X6 X5 X4 X3 X2 X1 — 0000 lo g CRCDAT 0644 CRC Data Input Register 0000 y In CRCWDAT 0646 CRC Result Register 0000 c . Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.

 TABLE 4-26: PERIPHERAL PIN SELECT REGISTER MAP 2 0 File All 1 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 Name Resets M ic RPINR0 0680 — — INT1R5 INT1R4 INT1R3 INT1R2 INT1R1 INT1R0 — — — — — — — — 3F00 roc RPINR1 0682 — — INT3R5 INT3R4 INT3R3 INT3R2 INT3R1 INT3R0 — — INT2R5 INT2R4 INT2R3 INT2R2 INT2R1 INT2R0 3F3F h ip RPINR2 0684 — — — — — — — — — — INT4R5 INT4R4 INT4R3 INT4R2 INT4R1 INT4R0 003F Te RPINR3 0686 — — T3CKR5 T3CKR4 T3CKR3 T3CKR2 T3CKR1 T3CKR0 — — T2CKR5 T2CKR4 T2CKR3 T2CKR2 T2CKR1 T2CKR0 3F3F c h RPINR4 0688 — — T5CKR5 T5CKR4 T5CKR3 T5CKR2 T5CKR1 T5CKR0 — — T4CKR5 T4CKR4 T4CKR3 T4CKR2 T4CKR1 T4CKR0 3F3F n o RPINR7 068E — — IC2R5 IC2R4 IC2R3 IC2R2 IC2R1 IC2R0 — — IC1R5 IC1R4 IC1R3 IC1R2 IC1R1 IC1R0 3F3F lo g RPINR8 0690 — — IC4R5 IC4R4 IC4R3 IC4R2 IC4R1 IC4R0 — — IC3R5 IC3R4 IC3R3 IC3R2 IC3R1 IC3R0 3F3F y In RPINR9 0692 — — IC6R5 IC6R4 IC6R3 IC6R2 IC6R1 IC6R0 — — IC5R5 IC5R4 IC5R3 IC5R2 IC5R1 IC5R0 3F3F c . RPINR10 0694 — — IC8R5 IC8R4 IC8R3 IC8R2 IC8R1 IC8R0 — — IC7R5 IC7R4 IC7R3 IC7R2 IC7R1 IC7R0 3F3F RPINR11 0696 — — OCFBR5 OCFBR4 OCFBR3 OCFBR2 OCFBR1 OCFBR0 — — OCFAR5 OCFAR4 OCFAR3 OCFAR2 OCFAR1 OCFAR0 3F3F RPINR15 069E — — IC9R5 IC9R4 IC9R3 IC9R2 IC9R1 IC9R0 — — — — — — — — 3F00 RPINR17 06A2 — — U3RXR5 U3RXR4 U3RXR3 U3RXR2 U3RXR1 U3RXR0 — — — — — — — — 3F00 RPINR18 06A4 — — U1CTSR5 U1CTSR4 U1CTSR3 U1CTSR2 U1CTSR1 U1CTSR0 — — U1RXR5 U1RXR4 U1RXR3 U1RXR2 U1RXR1 U1RXR0 3F3F RPINR19 06A6 — — U2CTSR5 U2CTSR4 U2CTSR3 U2CTSR2 U2CTSR1 U2CTSR0 — — U2RXR5 U2RXR4 U2RXR3 U2RXR2 U2RXR1 U2RXR0 3F3F RPINR20 06A8 — — SCK1R5 SCK1R4 SCK1R3 SCK1R2 SCK1R1 SCK1R0 — — SDI1R5 SDI1R4 SDI1R3 SDI1R2 SDI1R1 SDI1R0 3F3F P RPINR21 06AA — — U3CTSR5 U3CTSR4 U3CTSR3 U3CTSR2 U3CTSR1 U3CTSR0 — — SS1R5 SS1R4 SS1R3 SS1R2 SS1R1 SS1R0 3F3F RPINR22 06AC — — SCK2R5 SCK2R4 SCK2R3 SCK2R2 SCK2R1 SCK2R0 — — SDI2R5 SDI2R4 SDI2R3 SDI2R2 SDI2R1 SDI2R0 3F3F I C RPINR23 06AE — — — — — — — — — — SS2R5 SS2R4 SS2R3 SS2R2 SS2R1 SS2R0 3F3F RPINR27 06B6 — — U4CTSR5 U4CTSR4 U4CTSR3 U4CTSR2 U4CTSR1 U4CTSR0 — — U4RXR5 U4RXR4 U4RXR3 U4RXR2 U4RXR1 U4RXR0 3F3F 2 RPINR28 06B8 — — SCK3R5 SCK3R4 SCK3R3 SCK3R2 SCK3R1 SCK3R0 — — SDI3R5 SDI3R4 SDI3R3 SDI3R2 SDI3R1 SDI3R0 003F 4 RPINR29 06BA — — — — — — — — — — SS3R5 SS3R4 SS3R3 SS3R2 SS3R1 SS3R0 003F F RPOR0 06C0 — — RP1R5 RP1R4 RP1R3 RP1R2 RP1R1 RP1R0 — — RP0R5 RP0R4 RP0R3 RP0R2 RP0R1 RP0R0 0000 J RPOR1 06C2 — — RP3R5 RP3R4 RP3R3 RP3R2 RP3R1 RP3R0 — — RP2R5 RP2R4 RP2R3 RP2R2 RP2R1 RP2R0 0000 RPOR2 06C4 — — RP5R5(1) RP5R4(1) RP5R3(1) RP5R2(1) RP5R1(1) RP5R0(1) — — RP4R5 RP4R4 RP4R3 RP4R2 RP4R1 RP4R0 0000 2 RPOR3 06C6 — — RP7R5 RP7R4 RP7R3 RP7R2 RP7R1 RP7R0 — — RP6R5 RP6R4 RP6R3 RP6R2 RP6R1 RP6R0 0000 5 RPOR4 06C8 — — RP9R5 RP9R4 RP9R3 RP9R2 RP9R1 RP9R0 — — RP8R5 RP8R4 RP8R3 RP8R2 RP8R1 RP8R0 0000 6 RPOR5 06CA — — RP11R5 RP11R4 RP11R3 RP11R2 RP11R1 RP11R0 — — RP10R5 RP10R4 RP10R3 RP10R2 RP10R1 RP10R0 0000 G RPOR6 06CC — — RP13R5 RP13R4 RP13R3 RP13R2 RP13R1 RP13R0 — — RP12R5 RP12R4 RP12R3 RP12R2 RP12R1 RP12R0 0000 RPOR7 06CE — — RP15R5(1) RP15R4(1) RP15R3(1) RP15R2(1) RP15R1(1) RP15R0(1) — — RP14R5 RP14R4 RP14R3 RP14R2 RP14R1 RP14R0 0000 A RPOR8 06D0 — — RP17R5 RP17R4 RP17R3 RP17R2 RP17R1 RP17R0 — — RP16R5 RP16R4 RP16R3 RP16R2 RP16R1 RP16R0 0000 1 RPOR9 06D2 — — RP19R5 RP19R4 RP19R3 RP19R2 RP19R1 RP19R0 — — RP18R5 RP18R4 RP18R3 RP18R2 RP18R1 RP18R0 0000 1 RPOR10 06D4 — — RP21R5 RP21R4 RP21R3 RP21R2 RP21R1 RP21R0 — — RP20R5 RP20R4 RP20R3 RP20R2 RP20R1 RP20R0 0000 0 RPOR11 06D6 — — RP23R5 RP23R4 RP23R3 RP23R2 RP23R1 RP23R0 — — RP22R5 RP22R4 RP22R3 RP22R2 RP22R1 RP22R0 0000 RPOR12 06D8 — — RP25R5 RP25R4 RP25R3 RP25R2 RP25R1 RP25R0 — — RP24R5 RP24R4 RP24R3 RP24R2 RP24R1 RP24R0 0000 F RPOR13 06DA — — RP27R5 RP27R4 RP27R3 RP27R2 RP27R1 RP27R0 — — RP26R5 RP26R4 RP26R3 RP26R2 RP26R1 RP26R0 0000 D A S RPOR14 06DC — — RP29R5 RP29R4 RP29R3 RP29R2 RP29R1 RP29R0 — — RP28R5 RP28R4 RP28R3 RP28R2 RP28R1 RP28R0 0000 3 99 RPOR15 06DE — — RP31R5(2) RP31R4(2) RP31R3(2) RP31R2(2) RP31R1(2) RP31R0(2) — — RP30R5 RP30R4 RP30R3 RP30R2 RP30R1 RP30R0 0000 M 05 ALTRP 06E2 — — — — — — — — — — — — — — — SCK1CM xxx0 E -pa LNeogteend:1: —Bit s= aurnei munpilmempleenmteedn,t ereda ind 6a4s -‘p0i’n. Rdeevsiecte vsa; lrueeasd a arse ‘s0h’.own in hexadecimal. IL g e 5 2: Bits are unimplemented in 64-pin and 80-pin devices; read as ‘0’. Y 1

D TABLE 4-27: SYSTEM REGISTER MAP P S 3 990 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts IC 5 E -p RCON 0740 TRAPR IOPUWR — — — — CM PMSLP EXTR SWR SWDTEN WDTO SLEEP IDLE BOR POR Note 1 2 ag OSCCON 0742 — COSC2 COSC1 COSC0 — NOSC2 NOSC1 NOSC0 CLKLOCK IOLOCK LOCK — CF POSCEN SOSCEN OSWEN Note 2 4 e 5 CLKDIV 0744 ROI DOZE2 DOZE1 DOZE0 DOZEN RCDIV2 RCDIV1 RCDIV0 — — — — — — — — 0100 F 2 OSCTUN 0748 — — — — — — — — — — TUN5 TUN4 TUN3 TUN2 TUN1 TUN0 0000 J REFOCON 074E ROEN — ROSSLP ROSEL RODIV3 RODIV2 RODIV1 RODIV0 — — — — — — — — 0000 2 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Note 1: The Reset value of the RCON register is dependent on the type of Reset event. See Section6.0 “Resets” for more information. 5 2: The Reset value of the OSCCON register is dependent on both the type of Reset event and the device configuration. See Section8.0 “Oscillator Configuration” for more information. 6 G TABLE 4-28: NVM REGISTER MAP A File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 Name Resets 1 NVMCON 0760 WR WREN WRERR — — — — — — ERASE — — NVMOP3 NVMOP2 NVMOP1 NVMOP0 0000(1) 0 NVMKEY 0766 — — — — — — — — NVMKEY<7:0> 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. F Note 1: Reset value shown is for POR only. Value on other Reset states is dependent on the state of memory write or erase operations at the time of Reset. A M TABLE 4-29: PMD REGISTER MAP I File All L Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets Y PMD1 0770 T5MD T4MD T3MD T2MD T1MD — — — I2C1MD U2MD U1MD SPI2MD SPI1MD — — ADC1MD 0000 PMD2 0772 IC8MD IC7MD IC6MD IC5MD IC4MD IC3MD IC2MD IC1MD OC8MD OC7MD OC6MD OC5MD OC4MD OC3MD OC2MD OC1MD 0000 PMD3 0774 — — — — — CMPMD RTCCMD PMPMD CRCMD — — — U3MD I2C3MD I2C2MD — 0000 PMD4 0776 — — — — — — — — — — U4MD — REFOMD CTMUMD LVDMD — 0000 PMD5 0778 — — — — — — — IC9MD — — — — — — — OC9MD 0000 PMD6 077A — — — — — — — — — — — — — — — SPI3MD 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.  2 0 1 0 M ic ro c h ip T e c h n o lo g y In c .

PIC24FJ256GA110 FAMILY 4.2.5 SOFTWARE STACK 4.3 Interfacing Program and Data Memory Spaces In addition to its use as a working register, the W15 reg- ister in PIC24F devices is also used as a Software The PIC24F architecture uses a 24-bit wide program Stack Pointer. The pointer always points to the first space and a 16-bit wide data space. The architecture is available free word and grows from lower to higher also a modified Harvard scheme, meaning that data addresses. It predecrements for stack pops and can also be present in the program space. To use this post-increments for stack pushes, as shown in data successfully, it must be accessed in a way that Figure4-4. Note that for a PC push during any CALL preserves the alignment of information in both spaces. instruction, the MSB of the PC is zero-extended before Aside from normal execution, the PIC24F architecture the push, ensuring that the MSB is always clear. provides two methods by which program space can be Note: A PC push during exception processing accessed during operation: will concatenate the SRL register to the • Using table instructions to access individual bytes MSB of the PC prior to the push. or words anywhere in the program space The Stack Pointer Limit Value (SPLIM) register, associ- • Remapping a portion of the program space into ated with the Stack Pointer, sets an upper address the data space (program space visibility) boundary for the stack. SPLIM is uninitialized at Reset. Table instructions allow an application to read or write As is the case for the Stack Pointer, SPLIM<0> is to small areas of the program memory. This makes the forced to ‘0’ because all stack operations must be method ideal for accessing data tables that need to be word-aligned. Whenever an EA is generated using updated from time to time. It also allows access to all W15 as a source or destination pointer, the resulting bytes of the program word. The remapping method address is compared with the value in SPLIM. If the allows an application to access a large block of data on contents of the Stack Pointer (W15) and the SPLIM a read-only basis, which is ideal for look-ups from a register are equal, and a push operation is performed, large table of static data; it can only access the least a stack error trap will not occur. The stack error trap will significant word of the program word. occur on a subsequent push operation. Thus, for example, if it is desirable to cause a stack error trap 4.3.1 ADDRESSING PROGRAM SPACE when the stack grows beyond address 2000h in RAM, Since the address ranges for the data and program initialize the SPLIM with the value, 1FFEh. spaces are 16 and 24 bits, respectively, a method is Similarly, a Stack Pointer underflow (stack error) trap is needed to create a 23-bit or 24-bit program address generated when the Stack Pointer address is found to from 16-bit data registers. The solution depends on the be less than 0800h. This prevents the stack from interface method to be used. interfering with the Special Function Register (SFR) For table operations, the 8-bit Table Memory Page space. Address (TBLPAG) register is used to define a 32Kword A write to the SPLIM register should not be immediately region within the program space. This is concatenated followed by an indirect read operation using W15. with a 16-bit EA to arrive at a full 24-bit program space address. In this format, the Most Significant bit of FIGURE 4-4: CALL STACK FRAME TBLPAG is used to determine if the operation occurs in the user memory (TBLPAG<7> = 0) or the configuration 0000h 15 0 memory (TBLPAG<7> = 1). For remapping operations, the 8-bit Program Space s Visibility Page Address (PSVPAG) register is used to d waress define a 16Kword page in the program space. When Todr the Most Significant bit of the EA is ‘1’, PSVPAG is con- Grows gher Ad 000000P0C0<015P:C0><22:16> W15 (before CALL) c2a3t-ebnita pterodg rwaimth stphaec leo wadedr r1e5ss b. iUtsn loikf et htaeb lEeA o ptoe rfaotriomn sa, ck Hi <Free Word> W15 (after CALL) this limits remapping operations strictly to the user a St memory area. POP : [--W15] Table4-30 and Figure4-5 show how the program EA is PUSH: [W15++] created for table operations and remapping accesses from the data EA. Here, P<23:0> refers to a program space word, whereas D<15:0> refers to a data space word.  2010 Microchip Technology Inc. DS39905E-page 53

PIC24FJ256GA110 FAMILY TABLE 4-30: PROGRAM SPACE ADDRESS CONSTRUCTION Access Program Space Address Access Type Space <23> <22:16> <15> <14:1> <0> Instruction Access User 0 PC<22:1> 0 (Code Execution) 0xx xxxx xxxx xxxx xxxx xxx0 TBLRD/TBLWT User TBLPAG<7:0> Data EA<15:0> (Byte/Word Read/Write) 0xxx xxxx xxxx xxxx xxxx xxxx Configuration TBLPAG<7:0> Data EA<15:0> 1xxx xxxx xxxx xxxx xxxx xxxx Program Space Visibility User 0 PSVPAG<7:0> Data EA<14:0>(1) (Block Remap/Read) 0 xxxx xxxx xxx xxxx xxxx xxxx Note 1: Data EA<15> is always ‘1’ in this case, but is not used in calculating the program space address. Bit 15 of the address is PSVPAG<0>. FIGURE 4-5: DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION Program Counter(1) 0 Program Counter 0 23 Bits EA 1/0 Table Operations(2) 1/0 TBLPAG 8 Bits 16 Bits 24 Bits Select 1 EA 0 Program Space Visibility(1) 0 PSVPAG (Remapping) 8 Bits 15 Bits 23 Bits User/Configuration Byte Select Space Select Note1: The LSb of program space addresses is always fixed as ‘0’ in order to maintain word alignment of data in the program and data spaces. 2: Table operations are not required to be word-aligned. Table read operations are permitted in the configuration memory space. DS39905E-page 54  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 4.3.2 DATA ACCESS FROM PROGRAM 2. TBLRDH (Table Read High): In Word mode, it MEMORY USING TABLE maps the entire upper word of a program address INSTRUCTIONS (P<23:16>) to a data address. Note that D<15:8>, the ‘phantom’ byte, will always be ‘0’. The TBLRDL and TBLWTL instructions offer a direct In Byte mode, it maps the upper or lower byte of method of reading or writing the lower word of any the program word to D<7:0> of the data address within the program space without going through address, as above. Note that the data will data space. The TBLRDH and TBLWTH instructions are always be ‘0’ when the upper ‘phantom’ byte is the only method to read or write the upper 8 bits of a selected (byte select = 1). program space word as data. In a similar fashion, two table instructions, TBLWTH The PC is incremented by two for each successive and TBLWTL, are used to write individual bytes or 24-bit program word. This allows program memory words to a program space address. The details of addresses to directly map to data space addresses. their operation are explained in Section5.0 “Flash Program memory can thus be regarded as two, 16-bit Program Memory”. word-wide address spaces, residing side by side, each with the same address range. TBLRDL and TBLWTL For all table operations, the area of program memory access the space which contains the least significant space to be accessed is determined by the Table data word, and TBLRDH and TBLWTH access the space Memory Page Address (TBLPAG) register. TBLPAG which contains the upper data byte. covers the entire program memory space of the device, including user and configuration spaces. When Two table instructions are provided to move byte or TBLPAG<7> = 0, the table page is located in the user word-sized (16-bit) data to and from program space. memory space. When TBLPAG<7> = 1, the page is Both function as either byte or word operations. located in configuration space. 1. TBLRDL (Table Read Low): In Word mode, it Note: Only table read operations will execute in maps the lower word of the program space the configuration memory space, and only location (P<15:0>) to a data address (D<15:0>). then, in implemented areas, such as the In Byte mode, either the upper or lower byte of Device ID. Table write operations are not the lower program word is mapped to the lower allowed. byte of a data address. The upper byte is selected when the byte select is ‘1’; the lower byte is selected when it is ‘0’. FIGURE 4-6: ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS Program Space TBLPAG Data EA<15:0> 02 23 15 0 000000h 23 16 8 0 00000000 00000000 020000h 00000000 030000h 00000000 ‘Phantom’ Byte TBLRDH.B (Wn<0> = 0) TBLRDL.B (Wn<0> = 1) TBLRDL.B (Wn<0> = 0) TBLRDL.W The address for the table operation is determined by the data EA within the page defined by the TBLPAG register. 800000h Only read operations are shown; write operations are also valid in the user memory area.  2010 Microchip Technology Inc. DS39905E-page 55

PIC24FJ256GA110 FAMILY 4.3.3 READING DATA FROM PROGRAM 24-bit program word are used to contain the data. The MEMORY USING PROGRAM SPACE upper 8 bits of any program space locations used as VISIBILITY data should be programmed with ‘1111 1111’ or ‘0000 0000’ to force a NOP. This prevents possible The upper 32Kbytes of data space may optionally be issues should the area of code ever be accidentally mapped into any 16Kword page of the program space. executed. This provides transparent access of stored constant data from the data space without the need to use Note: PSV access is temporarily disabled during special instructions (i.e., TBLRDL/H). table reads/writes. Program space access through the data space occurs if For operations that use PSV and are executed outside the Most Significant bit (MSb) of the data space EA is ‘1’ a REPEAT loop, the MOV and MOV.D instructions will and program space visibility is enabled by setting the require one instruction cycle in addition to the specified PSV bit in the CPU Control (CORCON<2>) register. The execution time. All other instructions will require two location of the program memory space to be mapped instruction cycles in addition to the specified execution into the data space is determined by the Program Space time. Visibility Page Address (PSVPAG) register. This 8-bit For operations that use PSV which are executed inside register defines any one of 256 possible pages of a REPEAT loop, there will be some instances that 16Kwords in program space. In effect, PSVPAG func- require two instruction cycles in addition to the tions as the upper 8 bits of the program memory specified execution time of the instruction: address, with the 15bits of the EA functioning as the lower bits. Note that by incrementing the PC by 2 for • Execution in the first iteration each program memory word, the lower 15 bits of data • Execution in the last iteration space addresses directly map to the lower 15 bits in the • Execution prior to exiting the loop due to an corresponding program space addresses. interrupt Data reads to this area add an additional cycle to the • Execution upon re-entering the loop after an instruction being executed, since two program memory interrupt is serviced fetches are required. Any other iteration of the REPEAT loop will allow the Although each data space address, 8000h and higher, instruction accessing data, using PSV, to execute in a maps directly into a corresponding program memory single cycle. address (see Figure4-7), only the lower 16bits of the FIGURE 4-7: PROGRAM SPACE VISIBILITY OPERATION When CORCON<2> = 1 and EA<15> = 1: Program Space Data Space PSVPAG 23 15 0 02 000000h 0000h Data EA<14:0> 010000h 018000h The data in the page designated by PSV- PAG is mapped into the upper half of the data memory 8000h space.... PSV Area ...while the lower 15 bits of the EA specify an exact FFFFh address within the PSV area. This corresponds exactly to the same lower 15 bits of the actual program 800000h space address. DS39905E-page 56  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 5.0 FLASH PROGRAM MEMORY RTSP is accomplished using TBLRD (table read) and TBLWT (table write) instructions. With RTSP, the user Note: This data sheet summarizes the features of may write program memory data in blocks of 64 instruc- this group of PIC24F devices. It is not tions (192 bytes) at a time and erase program memory intended to be a comprehensive reference in blocks of 512 instructions (1536 bytes) at a time. source. For more information, refer to the “PIC24F Family Reference Manual”, 5.1 Table Instructions and Flash Section 4. “Program Memory” Programming (DS39715). Regardless of the method used, all programming of The PIC24FJ256GA110 family of devices contains Flash memory is done with the table read and table internal Flash program memory for storing and execut- write instructions. These allow direct read and write ing application code. The memory is readable, writable access to the program memory space from the data and erasable when operating with VDD over 2.35V. If memory while the device is in normal operating mode. the regulator is disabled, the VDDCORE voltage must be The 24-bit target address in the program memory is over 2.25V. formed using the TBLPAG<7:0> bits and the Effective Flash memory can be programmed in three ways: Address (EA) from a W register specified in the table instruction, as shown in Figure5-1. • In-Circuit Serial Programming™ (ICSP™) • Run-Time Self-Programming (RTSP) The TBLRDL and the TBLWTL instructions are used to read or write to bits<15:0> of program memory. • Enhanced In-Circuit Serial Programming TBLRDL and TBLWTL can access program memory in (Enhanced ICSP) both Word and Byte modes. ICSP allows a PIC24FJ256GA110 family device to be The TBLRDH and TBLWTH instructions are used to read serially programmed while in the end application circuit. or write to bits<23:16> of program memory. TBLRDH This is simply done with two lines for the programming and TBLWTH can also access program memory in Word clock and programming data (which are named PGECx or Byte mode. and PGEDx, respectively), and three other lines for power (VDD), ground (VSS) and Master Clear (MCLR). This allows customers to manufacture boards with unprogrammed devices and then program the micro- controller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. FIGURE 5-1: ADDRESSING FOR TABLE REGISTERS 24 Bits Using Program 0 Program Counter 0 Counter Working Reg EA Using 1/0 TBLPAG Reg Table Instruction 8 Bits 16 Bits User/Configuration Byte Space Select 24-Bit EA Select  2010 Microchip Technology Inc. DS39905E-page 57

PIC24FJ256GA110 FAMILY 5.2 RTSP Operation 5.3 JTAG Operation The PIC24F Flash program memory array is organized The PIC24F family supports JTAG boundary scan. into rows of 64 instructions or 192 bytes. RTSP allows Boundary scan can improve the manufacturing the user to erase blocks of eight rows (512 instructions) process by verifying pin to PCB connectivity. at a time and to program one row at a time. It is also possible to program single words. 5.4 Enhanced In-Circuit Serial The 8-row erase blocks and single row write blocks are Programming edge-aligned, from the beginning of program memory, on Enhanced In-Circuit Serial Programming uses an boundaries of 1536 bytes and 192 bytes, respectively. on-board bootloader, known as the program executive, When data is written to program memory using TBLWT to manage the programming process. Using an SPI instructions, the data is not written directly to memory. data frame format, the program executive can erase, Instead, data written using table writes is stored in program and verify program memory. For more holding latches until the programming sequence is information on Enhanced ICSP, see the device executed. programming specification. Any number of TBLWT instructions can be executed and a write will be successfully performed. However, 5.5 Control Registers 64TBLWT instructions are required to write the full row There are two SFRs used to read and write the of memory. program Flash memory: NVMCON and NVMKEY. To ensure that no data is corrupted during a write, any The NVMCON register (Register5-1) controls which unused addresses should be programmed with blocks are to be erased, which memory type is to be FFFFFFh. This is because the holding latches reset to programmed and when the programming cycle starts. an unknown state, so if the addresses are left in the Reset state, they may overwrite the locations on rows NVMKEY is a write-only register that is used for write which were not rewritten. protection. To start a programming or erase sequence, the user must consecutively write 55h and AAh to the The basic sequence for RTSP programming is to set up NVMKEY register. Refer to Section5.6 “Programming a Table Pointer, then do a series of TBLWT instructions Operations” for further details. to load the buffers. Programming is performed by setting the control bits in the NVMCON register. 5.6 Programming Operations Data can be loaded in any order and the holding regis- ters can be written to multiple times before performing A complete programming sequence is necessary for a write operation. Subsequent writes, however, will programming or erasing the internal Flash in RTSP wipe out any previous writes. mode. During a programming or erase operation, the processor stalls (waits) until the operation is finished. Note: Writing to a location multiple times without Setting the WR bit (NVMCON<15>) starts the opera- erasing is not recommended. tion and the WR bit is automatically cleared when the All of the table write operations are single-word writes operation is finished. (2 instruction cycles), because only the buffers are writ- ten. A programming cycle is required for programming each row. DS39905E-page 58  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 5-1: NVMCON: FLASH MEMORY CONTROL REGISTER R/SO-0(1) R/W-0(1) R/W-0(1) U-0 U-0 U-0 U-0 U-0 WR WREN WRERR — — — — — bit 15 bit 8 U-0 R/W-0(1) U-0 U-0 R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) — ERASE — — NVMOP3(2) NVMOP2(2) NVMOP1(2) NVMOP0(2) bit 7 bit 0 Legend: SO = Set Only bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 WR: Write Control bit(1) 1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is cleared by hardware once the operation is complete. 0 = Program or erase operation is complete and inactive bit 14 WREN: Write Enable bit(1) 1 = Enable Flash program/erase operations 0 = Inhibit Flash program/erase operations bit 13 WRERR: Write Sequence Error Flag bit(1) 1 = An improper program or erase sequence attempt or termination has occurred (bit is set automatically on any set attempt of the WR bit) 0 = The program or erase operation completed normally bit 12-7 Unimplemented: Read as ‘0’ bit 6 ERASE: Erase/Program Enable bit(1) 1 = Perform the erase operation specified by NVMOP<3:0> on the next WR command 0 = Perform the program operation specified by NVMOP<3:0> on the next WR command bit 5-4 Unimplemented: Read as ‘0’ bit 3-0 NVMOP<3:0>: NVM Operation Select bits(1,2) 1111 = Memory bulk erase operation (ERASE = 1) or no operation (ERASE = 0)(3) 0011 = Memory word program operation (ERASE = 0) or no operation (ERASE = 1) 0010 = Memory page erase operation (ERASE = 1) or no operation (ERASE = 0) 0001 = Memory row program operation (ERASE = 0) or no operation (ERASE = 1) Note 1: These bits can only be reset on POR. 2: All other combinations of NVMOP<3:0> are unimplemented. 3: Available in ICSP™ mode only. Refer to the device programming specification.  2010 Microchip Technology Inc. DS39905E-page 59

PIC24FJ256GA110 FAMILY 5.6.1 PROGRAMMING ALGORITHM FOR 5. Write the program block to Flash memory: FLASH PROGRAM MEMORY a) Set the NVMOP bits to ‘0001’ to configure for row programming. Clear the ERASE bit The user can program one row of Flash program memory and set the WREN bit. at a time. To do this, it is necessary to erase the 8-row erase block containing the desired row. The general b) Write 55h to NVMKEY. process is as follows: c) Write AAh to NVMKEY. 1. Read eight rows of program memory d) Set the WR bit. The programming cycle (512instructions) and store in data RAM. begins and the CPU stalls for the duration of the write cycle. When the write to Flash 2. Update the program data in RAM with the memory is done, the WR bit is cleared desired new data. automatically. 3. Erase the block (see Example5-1 for an 6. Repeat Steps 4 and 5, using the next available implementation in assembler): 64instructions from the block in data RAM by a) Set the NVMOP bits (NVMCON<3:0>) to incrementing the value in TBLPAG, until all ‘0010’ to configure for block erase. Set the 512instructions are written back to Flash ERASE (NVMCON<6>) and WREN memory. (NVMCON<14>) bits. For protection against accidental operations, the write b) Write the starting address of the block to be initiate sequence for NVMKEY must be used to allow erased into the TBLPAG and W registers. any erase or program operation to proceed. After the c) Write 55h to NVMKEY. programming command has been executed, the user d) Write AAh to NVMKEY. must wait for the programming time until programming e) Set the WR bit (NVMCON<15>). The erase is complete. The two instructions following the start of cycle begins and the CPU stalls for the dura- the programming sequence should be NOPs, as shown tion of the erase cycle. When the erase is in Example5-5. done, the WR bit is cleared automatically. Note: The equivalent C code for these steps, 4. Write the first 64 instructions from data RAM into prepared using Microchip’s MPLAB C30 the program memory buffers (see Example5-3 compiler and a specific library of built-in for the implementation in assembler). hardware functions, is shown in Examples5-2,5-4 and5-6. EXAMPLE 5-1: ERASING A PROGRAM MEMORY BLOCK (ASSEMBLY LANGUAGE CODE) ; Set up NVMCON for block erase operation MOV #0x4042, W0 ; MOV W0, NVMCON ; Initialize NVMCON ; Init pointer to row to be ERASED MOV #tblpage(PROG_ADDR), W0 ; MOV W0, TBLPAG ; Initialize PM Page Boundary SFR MOV #tbloffset(PROG_ADDR), W0 ; Initialize in-page EA[15:0] pointer TBLWTL W0, [W0] ; Set base address of erase block DISI #5 ; Block all interrupts with priority <7 ; for next 5 instructions MOV #0x55, W0 MOV W0, NVMKEY ; Write the 55 key MOV #0xAA, W1 ; MOV W1, NVMKEY ; Write the AA key BSET NVMCON, #WR ; Start the erase sequence NOP ; Insert two NOPs after the erase NOP ; command is asserted DS39905E-page 60  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY EXAMPLE 5-2: ERASING A PROGRAM MEMORY BLOCK (C LANGUAGE CODE) // C example using MPLAB C30 unsigned long progAddr = 0xXXXXXX; // Address of row to write unsigned int offset; //Set up pointer to the first memory location to be written TBLPAG = progAddr>>16; // Initialize PM Page Boundary SFR offset = progAddr & 0xFFFF; // Initialize lower word of address __builtin_tblwtl(offset, 0x0000); // Set base address of erase block // with dummy latch write NVMCON = 0x4042; // Initialize NVMCON asm("DISI #5"); // Block all interrupts with priority <7 // for next 5 instructions __builtin_write_NVM(); // C30 function to perform unlock // sequence and set WR EXAMPLE 5-3: LOADING THE WRITE BUFFERS (ASSEMBLY LANGUAGE CODE) ; Set up NVMCON for row programming operations MOV #0x4001, W0 ; MOV W0, NVMCON ; Initialize NVMCON ; Set up a pointer to the first program memory location to be written ; program memory selected, and writes enabled MOV #0x0000, W0 ; MOV W0, TBLPAG ; Initialize PM Page Boundary SFR MOV #0x6000, W0 ; An example program memory address ; Perform the TBLWT instructions to write the latches ; 0th_program_word MOV #LOW_WORD_0, W2 ; MOV #HIGH_BYTE_0, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 1st_program_word MOV #LOW_WORD_1, W2 ; MOV #HIGH_BYTE_1, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 2nd_program_word MOV #LOW_WORD_2, W2 ; MOV #HIGH_BYTE_2, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch • • • ; 63rd_program_word MOV #LOW_WORD_31, W2 ; MOV #HIGH_BYTE_31, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0] ; Write PM high byte into program latch  2010 Microchip Technology Inc. DS39905E-page 61

PIC24FJ256GA110 FAMILY EXAMPLE 5-4: LOADING THE WRITE BUFFERS (C LANGUAGE CODE) // C example using MPLAB C30 #define NUM_INSTRUCTION_PER_ROW 64 unsigned int offset; unsigned int i; unsigned long progAddr = 0xXXXXXX; // Address of row to write unsigned int progData[2*NUM_INSTRUCTION_PER_ROW]; // Buffer of data to write //Set up NVMCON for row programming NVMCON = 0x4001; // Initialize NVMCON //Set up pointer to the first memory location to be written TBLPAG = progAddr>>16; // Initialize PM Page Boundary SFR offset = progAddr & 0xFFFF; // Initialize lower word of address //Perform TBLWT instructions to write necessary number of latches for(i=0; i < 2*NUM_INSTRUCTION_PER_ROW; i++) { __builtin_tblwtl(offset, progData[i++]); // Write to address low word __builtin_tblwth(offset, progData[i]); // Write to upper byte offset = offset + 2; // Increment address } EXAMPLE 5-5: INITIATING A PROGRAMMING SEQUENCE (ASSEMBLY LANGUAGE CODE) DISI #5 ; Block all interrupts with priority <7 ; for next 5 instructions MOV #0x55, W0 MOV W0, NVMKEY ; Write the 55 key MOV #0xAA, W1 ; MOV W1, NVMKEY ; Write the AA key BSET NVMCON, #WR ; Start the erase sequence NOP ; NOP ; BTSC NVMCON, #15 ; and wait for it to be BRA $-2 ; completed EXAMPLE 5-6: INITIATING A PROGRAMMING SEQUENCE (C LANGUAGE CODE) // C example using MPLAB C30 asm("DISI #5"); // Block all interrupts with priority < 7 // for next 5 instructions __builtin_write_NVM(); // Perform unlock sequence and set WR DS39905E-page 62  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 5.6.2 PROGRAMMING A SINGLE WORD and specify the lower 16 bits of the program memory OF FLASH PROGRAM MEMORY address to write to. To configure the NVMCON register for a word write, set the NVMOP bits (NVMCON<3:0>) If a Flash location has been erased, it can be pro- to ‘0011’. The write is performed by executing the grammed using table write instructions to write an unlock sequence and setting the WR bit, as shown in instruction word (24-bit) into the write latch. The Example5-7. An equivalent procedure in C, using the TBLPAG register is loaded with the 8 Most Significant MPLAB C30 compiler and built-in hardware functions, Bytes of the Flash address. The TBLWTL and TBLWTH is shown in Example5-8. instructions write the desired data into the write latches EXAMPLE 5-7: PROGRAMMING A SINGLE WORD OF FLASH PROGRAM MEMORY (ASSEMBLY LANGUAGE CODE) ; Setup a pointer to data Program Memory MOV #tblpage(PROG_ADDR), W0 ; MOV W0, TBLPAG ;Initialize PM Page Boundary SFR MOV #tbloffset(PROG_ADDR), W0 ;Initialize a register with program memory address MOV #LOW_WORD, W2 ; MOV #HIGH_BYTE, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; Setup NVMCON for programming one word to data Program Memory MOV #0x4003, W0 ; MOV W0, NVMCON ; Set NVMOP bits to 0011 DISI #5 ; Disable interrupts while the KEY sequence is written MOV #0x55, W0 ; Write the key sequence MOV W0, NVMKEY MOV #0xAA, W0 MOV W0, NVMKEY BSET NVMCON, #WR ; Start the write cycle NOP ; Insert two NOPs after the erase NOP ; Command is asserted EXAMPLE 5-8: PROGRAMMING A SINGLE WORD OF FLASH PROGRAM MEMORY (CLANGUAGE CODE) // C example using MPLAB C30 unsigned int offset; unsigned long progAddr = 0xXXXXXX; // Address of word to program unsigned int progDataL = 0xXXXX; // Data to program lower word unsigned char progDataH = 0xXX; // Data to program upper byte //Set up NVMCON for word programming NVMCON = 0x4003; // Initialize NVMCON //Set up pointer to the first memory location to be written TBLPAG = progAddr>>16; // Initialize PM Page Boundary SFR offset = progAddr & 0xFFFF; // Initialize lower word of address //Perform TBLWT instructions to write latches __builtin_tblwtl(offset, progDataL); // Write to address low word __builtin_tblwth(offset, progDataH); // Write to upper byte asm(“DISI #5”); // Block interrupts with priority < 7 // for next 5 instructions __builtin_write_NVM(); // C30 function to perform unlock // sequence and set WR  2010 Microchip Technology Inc. DS39905E-page 63

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 64  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 6.0 RESETS Any active source of Reset will make the SYSRST signal active. Many registers associated with the CPU Note: This data sheet summarizes the features of and peripherals are forced to a known Reset state. this group of PIC24F devices. It is not Most registers are unaffected by a Reset; their status is intended to be a comprehensive reference unknown on POR and unchanged by all other Resets. source. For more information, refer to the “PIC24F Family Reference Manual”, Note: Refer to the specific peripheral or CPU section of this manual for register Reset Section 7. “Reset” (DS39712). states. The Reset module combines all Reset sources and controls the device Master Reset Signal, SYSRST. The All types of device Reset will set a corresponding status following is a list of device Reset sources: bit in the RCON register to indicate the type of Reset (see Register6-1). A Power-on Reset will clear all bits • POR: Power-on Reset except for the BOR and POR bits (RCON<1:0>) which • MCLR: Pin Reset are set. The user may set or clear any bit at any time • SWR: RESET Instruction during code execution. The RCON bits only serve as • WDT: Watchdog Timer Reset status bits. Setting a particular Reset status bit in software will not cause a device Reset to occur. • BOR: Brown-out Reset • CM: Configuration Mismatch Reset The RCON register also has other bits associated with the Watchdog Timer and device power-saving states. • TRAPR: Trap Conflict Reset The function of these bits is discussed in other sections • IOPUWR: Illegal Opcode Reset of this data sheet. • UWR: Uninitialized W Register Reset Note: The status bits in the RCON register A simplified block diagram of the Reset module is should be cleared after they are read so shown in Figure6-1. that the next RCON register value after a device Reset will be meaningful. FIGURE 6-1: RESET SYSTEM BLOCK DIAGRAM RESET Instruction Glitch Filter MCLR WDT Module Sleep or Idle VDD Rise POR Detect SYSRST VDD Brown-out BOR Reset Enable Voltage Regulator Trap Conflict Illegal Opcode Configuration Mismatch Uninitialized W Register  2010 Microchip Technology Inc. DS39905E-page 65

PIC24FJ256GA110 FAMILY REGISTER 6-1: RCON: RESET CONTROL REGISTER(1) R/W-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 TRAPR IOPUWR — — — — CM PMSLP bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 EXTR SWR SWDTEN(2) WDTO SLEEP IDLE BOR POR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TRAPR: Trap Reset Flag bit 1 = A Trap Conflict Reset has occurred 0 = A Trap Conflict Reset has not occurred bit 14 IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit 1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an Address Pointer caused a Reset 0 = An illegal opcode or uninitialized W Reset has not occurred bit 13-10 Unimplemented: Read as ‘0’ bit 9 CM: Configuration Word Mismatch Reset Flag bit 1 = A Configuration Word Mismatch Reset has occurred 0 = A Configuration Word Mismatch Reset has not occurred bit 8 PMSLP: Program Memory Power During Sleep bit 1 = Program memory bias voltage remains powered during Sleep 0 = Program memory bias voltage is powered down during Sleep and voltage regulator enters Standby mode bit 7 EXTR: External Reset (MCLR) Pin bit 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred bit 6 SWR: Software Reset (Instruction) Flag bit 1 = A RESET instruction has been executed 0 = A RESET instruction has not been executed bit 5 SWDTEN: Software Enable/Disable of WDT bit(2) 1 = WDT is enabled 0 = WDT is disabled bit 4 WDTO: Watchdog Timer Time-out Flag bit 1 = WDT time-out has occurred 0 = WDT time-out has not occurred bit 3 SLEEP: Wake From Sleep Flag bit 1 = Device has been in Sleep mode 0 = Device has not been in Sleep mode bit 2 IDLE: Wake-up From Idle Flag bit 1 = Device has been in Idle mode 0 = Device has not been in Idle mode bit 1 BOR: Brown-out Reset Flag bit 1 = A Brown-out Reset has occurred. Note that BOR is also set after a Power-on Reset. 0 = A Brown-out Reset has not occurred bit 0 POR: Power-on Reset Flag bit 1 = A Power-on Reset has occurred 0 = A Power-on Reset has not occurred Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not cause a device Reset. 2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the SWDTEN bit setting. DS39905E-page 66  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 6-1: RESET FLAG BIT OPERATION Flag Bit Setting Event Clearing Event TRAPR (RCON<15>) Trap Conflict Event POR IOPUWR (RCON<14>) Illegal Opcode or Uninitialized W Register Access POR CM (RCON<9>) Configuration Mismatch Reset POR EXTR (RCON<7>) MCLR Reset POR SWR (RCON<6>) RESET Instruction POR WDTO (RCON<4>) WDT Time-out PWRSAV Instruction, POR, CLRWDT SLEEP (RCON<3>) PWRSAV #SLEEP Instruction POR IDLE (RCON<2>) PWRSAV #IDLE Instruction POR BOR (RCON<1>) POR, BOR — POR (RCON<0>) POR — Note: All Reset flag bits may be set or cleared by the user software. 6.1 Clock Source Selection at Reset 6.2 Device Reset Times If clock switching is enabled, the system clock source at The Reset times for various types of device Reset are device Reset is chosen as shown in Table6-2. If clock summarized in Table6-3. Note that the system Reset switching is disabled, the system clock source is always signal, SYSRST, is released after the POR and PWRT selected according to the oscillator Configuration bits. delay times expire. Refer to Section8.0 “Oscillator Configuration” for The time at which the device actually begins to execute further details. code will also depend on the system oscillator delays, which include the Oscillator Start-up Timer (OST) and TABLE 6-2: OSCILLATOR SELECTION vs. the PLL lock time. The OST and PLL lock times occur TYPE OF RESET (CLOCK in parallel with the applicable SYSRST delay times. SWITCHING ENABLED) The FSCM delay determines the time at which the Reset Type Clock Source Determinant FSCM begins to monitor the system clock source after the SYSRST signal is released. POR FNOSC Configuration bits BOR (CW2<10:8>) MCLR COSC Control bits WDTO (OSCCON<14:12>) SWR  2010 Microchip Technology Inc. DS39905E-page 67

PIC24FJ256GA110 FAMILY TABLE 6-3: RESET DELAY TIMES FOR VARIOUS DEVICE RESETS System Clock Reset Type Clock Source SYSRST Delay Notes Delay POR(6) EC TPOR + TPWRT + TRST — 1, 2, 7 FRC, FRCDIV TPOR + TPWRT + TRST TFRC 1, 2, 3, 7 LPRC TPOR + TPWRT + TRST TLPRC 1, 2, 3, 7 ECPLL TPOR + TPWRT + TRST TLOCK 1, 2, 4, 7 FRCPLL TPOR + TPWRT + TRST TFRC + TLOCK 1, 2, 3, 4, 7 XT, HS, SOSC TPOR + TPWRT + TRST TOST 1, 2, 5, 7 XTPLL, HSPLL TPOR + TPWRT + TRST TOST + TLOCK 1, 2, 4, 5, 7 BOR EC TPWRT + TRST — 2, 7 FRC, FRCDIV TPWRT + TRST TFRC 2, 3, 7 LPRC TPWRT + TRST TLPRC 2, 3, 7 ECPLL TPWRT + TRST TLOCK 2, 4, 7 FRCPLL TPWRT + TRST TFRC + TLOCK 2, 3, 4, 7 XT, HS, SOSC TPWRT + TRST TOST 2, 5, 7 XTPLL, HSPLL TPWRT + TRST TFRC + TLOCK 2, 3, 4, 7 All Others Any Clock TRST — 7 Note 1: TPOR = Power-on Reset delay. 2: TPWRT = 64 ms nominal if regulator is disabled (ENVREG tied to VSS). 3: TFRC and TLPRC = RC Oscillator start-up times. 4: TLOCK = PLL lock time. 5: TOST = Oscillator Start-up Timer (OST). A 10-bit counter waits 1024 oscillator periods before releasing the oscillator clock to the system. 6: If Two-Speed Start-up is enabled, regardless of the Primary Oscillator selected, the device starts with FRC, and in such cases, FRC start-up time is valid. 7: TRST = Internal State Reset Timer Note: For detailed operating frequency and timing specifications, see Section28.0 “Electrical Characteristics”. DS39905E-page 68  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 6.2.1 POR AND LONG OSCILLATOR 6.3 Special Function Register Reset START-UP TIMES States The oscillator start-up circuitry and its associated delay Most of the Special Function Registers (SFRs) associ- timers are not linked to the device Reset delays that ated with the PIC24F CPU and peripherals are reset to a occur at power-up. Some crystal circuits (especially particular value at a device Reset. The SFRs are low-frequency crystals) will have a relatively long grouped by their peripheral or CPU function and their start-up time. Therefore, one or more of the following Reset values are specified in each section of this manual. conditions is possible after SYSRST is released: The Reset value for each SFR does not depend on the • The oscillator circuit has not begun to oscillate. type of Reset with the exception of four registers. The • The Oscillator Start-up Timer has not expired (if a Reset value for the Reset Control register, RCON, will crystal oscillator is used). depend on the type of device Reset. The Reset value • The PLL has not achieved a lock (if PLL is used). for the Oscillator Control register, OSCCON, will depend on the type of Reset and the programmed The device will not begin to execute code until a valid values of the FNOSC bits in Flash Configuration clock source has been released to the system. There- Word2 (CW2); see Table6-2. The RCFGCAL and fore, the oscillator and PLL start-up delays must be NVMCON registers are only affected by a POR. considered when the Reset delay time must be known. 6.2.2 FAIL-SAFE CLOCK MONITOR (FSCM) AND DEVICE RESETS If the FSCM is enabled, it will begin to monitor the system clock source when SYSRST is released. If a valid clock source is not available at this time, the device will automatically switch to the FRC Oscillator and the user can switch to the desired crystal oscillator in the Trap Service Routine (TSR).  2010 Microchip Technology Inc. DS39905E-page 69

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 70  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 7.0 INTERRUPT CONTROLLER 7.1.1 ALTERNATE INTERRUPT VECTOR TABLE Note: This data sheet summarizes the features of The Alternate Interrupt Vector Table (AIVT) is located this group of PIC24F devices. It is not after the IVT, as shown in Figure7-1. Access to the intended to be a comprehensive reference AIVT is provided by the ALTIVT control bit source. For more information, refer to the (INTCON2<15>). If the ALTIVT bit is set, all interrupt “PIC24F Family Reference Manual”, and exception processes will use the alternate vectors Section 8. “Interrupts” (DS39707). instead of the default vectors. The alternate vectors are The PIC24F interrupt controller reduces the numerous organized in the same manner as the default vectors. peripheral interrupt request signals to a single interrupt The AIVT supports emulation and debugging efforts by request signal to the PIC24F CPU. It has the following providing a means to switch between an application features: and a support environment without requiring the inter- • Up to 8 processor exceptions and software traps rupt vectors to be reprogrammed. This feature also enables switching between applications for evaluation • 7 user-selectable priority levels of different software algorithms at run time. If the AIVT • Interrupt Vector Table (IVT) with up to 118 vectors is not needed, the AIVT should be programmed with • A unique vector for each interrupt or exception the same addresses used in the IVT. source • Fixed priority within a specified user priority level 7.2 Reset Sequence • Alternate Interrupt Vector Table (AIVT) for debug A device Reset is not a true exception because the support interrupt controller is not involved in the Reset process. • Fixed interrupt entry and return latencies The PIC24F devices clear their registers in response to a Reset which forces the PC to zero. The micro- 7.1 Interrupt Vector Table controller then begins program execution at location The Interrupt Vector Table (IVT) is shown in Figure7-1. 000000h. The user programs a GOTO instruction at the The IVT resides in program memory, starting at location Reset address, which redirects program execution to 000004h. The IVT contains 126 vectors, consisting of the appropriate start-up routine. 8non-maskable trap vectors, plus up to 118 sources of Note: Any unimplemented or unused vector interrupt. In general, each interrupt source has its own locations in the IVT and AIVT should be vector. Each interrupt vector contains a 24-bit wide programmed with the address of a default address. The value programmed into each interrupt interrupt handler routine that contains a vector location is the starting address of the associated RESET instruction. Interrupt Service Routine (ISR). Interrupt vectors are prioritized in terms of their natural priority; this is linked to their position in the vector table. All other things being equal, lower addresses have a higher natural priority. For example, the interrupt asso- ciated with vector 0 will take priority over interrupts at any other vector address. PIC24FJ256GA110 family devices implement non-maskable traps and unique interrupts. These are summarized in Table7-1 and Table7-2.  2010 Microchip Technology Inc. DS39905E-page 71

PIC24FJ256GA110 FAMILY FIGURE 7-1: PIC24F INTERRUPT VECTOR TABLE Reset – GOTO Instruction 000000h Reset – GOTO Address 000002h Reserved 000004h Oscillator Fail Trap Vector Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 000014h Interrupt Vector 1 — — — Interrupt Vector 52 00007Ch y Interrupt Vector Table (IVT)(1) orit Interrupt Vector 53 00007Eh Pri Interrupt Vector 54 000080h er — d — Or — ural Interrupt Vector 116 0000FCh at Interrupt Vector 117 0000FEh N g Reserved 000100h n Reserved 000102h si a Reserved e cr Oscillator Fail Trap Vector e D Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 000114h Interrupt Vector 1 — — — Alternate Interrupt Vector Table (AIVT)(1) Interrupt Vector 52 00017Ch Interrupt Vector 53 00017Eh Interrupt Vector 54 000180h — — — Interrupt Vector 116 Interrupt Vector 117 0001FEh Start of Code 000200h Note 1: See Table7-2 for the interrupt vector list. TABLE 7-1: TRAP VECTOR DETAILS Vector Number IVT Address AIVT Address Trap Source 0 000004h 000104h Reserved 1 000006h 000106h Oscillator Failure 2 000008h 000108h Address Error 3 00000Ah 00010Ah Stack Error 4 00000Ch 00010Ch Math Error 5 00000Eh 00010Eh Reserved 6 000010h 000110h Reserved 7 000012h 000112h Reserved DS39905E-page 72  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 7-2: IMPLEMENTED INTERRUPT VECTORS Interrupt Bit Locations Vector AIVT Interrupt Source IVT Address Number Address Flag Enable Priority ADC1 Conversion Done 13 00002Eh 00012Eh IFS0<13> IEC0<13> IPC3<6:4> Comparator Event 18 000038h 000138h IFS1<2> IEC1<2> IPC4<10:8> CRC Generator 67 00009Ah 00019Ah IFS4<3> IEC4<3> IPC16<14:12> CTMU Event 77 0000AEh 0001AEh IFS4<13> IEC4<13> IPC19<6:4> External Interrupt 0 0 000014h 000114h IFS0<0> IEC0<0> IPC0<2:0> External Interrupt 1 20 00003Ch 00013Ch IFS1<4> IEC1<4> IPC5<2:0> External Interrupt 2 29 00004Eh 00014Eh IFS1<13> IEC1<13> IPC7<6:4> External Interrupt 3 53 00007Eh 00017Eh IFS3<5> IEC3<5> IPC13<6:4> External Interrupt 4 54 000080h 000180h IFS3<6> IEC3<6> IPC13<10:8> I2C1 Master Event 17 000036h 000136h IFS1<1> IEC1<1> IPC4<6:4> I2C1 Slave Event 16 000034h 000134h IFS1<0> IEC1<0> IPC4<2:0> I2C2 Master Event 50 000078h 000178h IFS3<2> IEC3<2> IPC12<10:8> I2C2 Slave Event 49 000076h 000176h IFS3<1> IEC3<1> IPC12<6:4> I2C3 Master Event 85 0000BEh 0001BEh IFS5<5> IEC5<5> IPC21<6:4> I2C3 Slave Event 84 0000BCh 0001BCh IFS5<4> IEC5<4> IPC21<2:0> Input Capture 1 1 000016h 000116h IFS0<1> IEC0<1> IPC0<6:4> Input Capture 2 5 00001Eh 00011Eh IFS0<5> IEC0<5> IPC1<6:4> Input Capture 3 37 00005Eh 00015Eh IFS2<5> IEC2<5> IPC9<6:4> Input Capture 4 38 000060h 000160h IFS2<6> IEC2<6> IPC9<10:8> Input Capture 5 39 000062h 000162h IFS2<7> IEC2<7> IPC9<14:12> Input Capture 6 40 000064h 000164h IFS2<8> IEC2<8> IPC10<2:0> Input Capture 7 22 000040h 000140h IFS1<6> IEC1<6> IPC5<10:8> Input Capture 8 23 000042h 000142h IFS1<7> IEC1<7> IPC5<14:12> Input Capture 9 93 0000CEh 0001CEh IFS5<13> IEC5<13> IPC23<6:4> Input Change Notification 19 00003Ah 00013Ah IFS1<3> IEC1<3> IPC4<14:12> LVD Low-Voltage Detect 72 0000A4h 0001A4h IFS4<8> IEC4<8> IPC18<2:0> Output Compare 1 2 000018h 000118h IFS0<2> IEC0<2> IPC0<10:8> Output Compare 2 6 000020h 000120h IFS0<6> IEC0<6> IPC1<10:8> Output Compare 3 25 000046h 000146h IFS1<9> IEC1<9> IPC6<6:4> Output Compare 4 26 000048h 000148h IFS1<10> IEC1<10> IPC6<10:8> Output Compare 5 41 000066h 000166h IFS2<9> IEC2<9> IPC10<6:4> Output Compare 6 42 000068h 000168h IFS2<10> IEC2<10> IPC10<10:8> Output Compare 7 43 00006Ah 00016Ah IFS2<11> IEC2<11> IPC10<14:12> Output Compare 8 44 00006Ch 00016Ch IFS2<12> IEC2<12> IPC11<2:0> Output Compare 9 92 0000CCh 0001CCh IFS5<12> IEC5<12> IPC23<2:0> Parallel Master Port 45 00006Eh 00016Eh IFS2<13> IEC2<13> IPC11<6:4> Real-Time Clock/Calendar 62 000090h 000190h IFS3<14> IEC3<14> IPC15<10:8> SPI1 Error 9 000026h 000126h IFS0<9> IEC0<9> IPC2<6:4> SPI1 Event 10 000028h 000128h IFS0<10> IEC0<10> IPC2<10:8> SPI2 Error 32 000054h 000154h IFS2<0> IEC2<0> IPC8<2:0> SPI2 Event 33 000056h 000156h IFS2<1> IEC2<1> IPC8<6:4> SPI3 Error 90 0000C8h 0001C8h IFS5<10> IEC5<10> IPC22<10:8> SPI3 Event 91 0000CAh 0001CAh IFS5<11> IEC5<11> IPC22<14:12>  2010 Microchip Technology Inc. DS39905E-page 73

PIC24FJ256GA110 FAMILY TABLE 7-2: IMPLEMENTED INTERRUPT VECTORS (CONTINUED) Interrupt Bit Locations Vector AIVT Interrupt Source IVT Address Number Address Flag Enable Priority Timer1 3 00001Ah 00011Ah IFS0<3> IEC0<3> IPC0<14:12> Timer2 7 000022h 000122h IFS0<7> IEC0<7> IPC1<14:12> Timer3 8 000024h 000124h IFS0<8> IEC0<8> IPC2<2:0> Timer4 27 00004Ah 00014Ah IFS1<11> IEC1<11> IPC6<14:12> Timer5 28 00004Ch 00014Ch IFS1<12> IEC1<12> IPC7<2:0> UART1 Error 65 000096h 000196h IFS4<1> IEC4<1> IPC16<6:4> UART1 Receiver 11 00002Ah 00012Ah IFS0<11> IEC0<11> IPC2<14:12> UART1 Transmitter 12 00002Ch 00012Ch IFS0<12> IEC0<12> IPC3<2:0> UART2 Error 66 000098h 000198h IFS4<2> IEC4<2> IPC16<10:8> UART2 Receiver 30 000050h 000150h IFS1<14> IEC1<14> IPC7<10:8> UART2 Transmitter 31 000052h 000152h IFS1<15> IEC1<15> IPC7<14:12> UART3 Error 81 0000B6h 0001B6h IFS5<1> IEC5<1> IPC20<6:4> UART3 Receiver 82 0000B8h 0001B8h IFS5<2> IEC5<2> IPC20<10:8> UART3 Transmitter 83 0000BAh 0001BAh IFS5<3> IEC5<3> IPC20<14:12> UART4 Error 87 0000C2h 0001C2h IFS5<7> IEC5<7> IPC21<14:12> UART4 Receiver 88 0000C4h 0001C4h IFS5<8> IEC5<8> IPC22<2:0> UART4 Transmitter 89 0000C6h 0001C6h IFS5<9> IEC5<9> IPC22<6:4> 7.3 Interrupt Control and Status The INTTREG register contains the associated inter- Registers rupt vector number and the new CPU interrupt priority level, which are latched into the Vector Number The PIC24FJ256GA110 family of devices implements (VECNUM<6:0>) and the Interrupt Level (ILR<3:0>) bit a total of 37 registers for the interrupt controller: fields in the INTTREG register. The new interrupt • INTCON1 priority level is the priority of the pending interrupt. • INTCON2 The interrupt sources are assigned to the IFSx, IECx • IFS0 through IFS5 and IPCx registers in the order of their vector numbers, as shown in Table7-2. For example, the INT0 (External • IEC0 through IEC5 Interrupt 0) is shown as having a vector number and a • IPC0 through IPC23 (except IPC14 and IPC17) natural order priority of 0. Thus, the INT0IF status bit is • INTTREG found in IFS0<0>, the INT0IE enable bit in IEC0<0> Global interrupt control functions are controlled from and the INT0IP<2:0> priority bits in the first position of INTCON1 and INTCON2. INTCON1 contains the Inter- IPC0 (IPC0<2:0>). rupt Nesting Disable (NSTDIS) bit, as well as the Although they are not specifically part of the interrupt control and status flags for the processor trap sources. control hardware, two of the CPU control registers con- The INTCON2 register controls the external interrupt tain bits that control interrupt functionality. The ALU request signal behavior and the use of the Alternate STATUS Register (SR) contains the IPL<2:0> bits Interrupt Vector Table. (SR<7:5>); these indicate the current CPU interrupt The IFSx registers maintain all of the interrupt request priority level. The user may change the current CPU flags. Each source of interrupt has a status bit which is priority level by writing to the IPL bits. set by the respective peripherals, or an external signal, The CORCON register contains the IPL3 bit, which and is cleared via software. together with IPL<2:0>, indicates the current CPU The IECx registers maintain all of the interrupt enable priority level. IPL3 is a read-only bit so that trap events bits. These control bits are used to individually enable cannot be masked by the user software. interrupts from the peripherals or external signals. All interrupt registers are described in Register7-1 The IPCx registers are used to set the interrupt priority through Register7-38, on the following pages. level for each source of interrupt. Each user interrupt source can be assigned to one of eight priority levels. DS39905E-page 74  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-1: SR: ALU STATUS REGISTER (IN CPU) U-0 U-0 U-0 U-0 U-0 U-0 U-0 R-0 — — — — — — — DC(1) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 IPL2(2,3) IPL1(2,3) IPL0(2,3) RA(1) N(1) OV(1) Z(1) C(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3) 111 = CPU interrupt priority level is 7 (15). User interrupts disabled. 110 = CPU interrupt priority level is 6 (14) 101 = CPU interrupt priority level is 5 (13) 100 = CPU interrupt priority level is 4 (12) 011 = CPU interrupt priority level is 3 (11) 010 = CPU interrupt priority level is 2 (10) 001 = CPU interrupt priority level is 1 (9) 000 = CPU interrupt priority level is 0 (8) Note 1: See Register3-1 for the description of the remaining bit(s) that are not dedicated to interrupt control functions. 2: The IPL bits are concatenated with the IPL3 bit (CORCON<3>) to form the CPU interrupt priority level. The value in parentheses indicates the interrupt priority level if IPL3 = 1. 3: The IPL Status bits are read-only when NSTDIS (INTCON1<15>) = 1. REGISTER 7-2: CORCON: CPU CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/C-0 R/W-0 U-0 U-0 — — — — IPL3(2) PSV(1) — — bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 3 IPL3: CPU Interrupt Priority Level Status bit(2) 1 = CPU interrupt priority level is greater than 7 0 = CPU interrupt priority level is 7 or less Note 1: See Register3-2 for the description of the remaining bit(s) that are not dedicated to interrupt control functions. 2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU interrupt priority level.  2010 Microchip Technology Inc. DS39905E-page 75

PIC24FJ256GA110 FAMILY REGISTER 7-3: INTCON1: INTERRUPT CONTROL REGISTER 1 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 NSTDIS — — — — — — — bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 — — — MATHERR ADDRERR STKERR OSCFAIL — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 NSTDIS: Interrupt Nesting Disable bit 1 = Interrupt nesting is disabled 0 = Interrupt nesting is enabled bit 14-5 Unimplemented: Read as ‘0’ bit 4 MATHERR: Arithmetic Error Trap Status bit 1 = Overflow trap has occurred 0 = Overflow trap has not occurred bit 3 ADDRERR: Address Error Trap Status bit 1 = Address error trap has occurred 0 = Address error trap has not occurred bit 2 STKERR: Stack Error Trap Status bit 1 = Stack error trap has occurred 0 = Stack error trap has not occurred bit 1 OSCFAIL: Oscillator Failure Trap Status bit 1 = Oscillator failure trap has occurred 0 = Oscillator failure trap has not occurred bit 0 Unimplemented: Read as ‘0’ DS39905E-page 76  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-4: INTCON2: INTERRUPT CONTROL REGISTER 2 R/W-0 R-0 U-0 U-0 U-0 U-0 U-0 U-0 ALTIVT DISI — — — — — — bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — INT4EP INT3EP INT2EP INT1EP INT0EP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ALTIVT: Enable Alternate Interrupt Vector Table bit 1 = Use Alternate Interrupt Vector Table 0 = Use standard (default) vector table bit 14 DISI: DISI Instruction Status bit 1 = DISI instruction is active 0 = DISI instruction is not active bit 13-5 Unimplemented: Read as ‘0’ bit 4 INT4EP: External Interrupt 4 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 3 INT3EP: External Interrupt 3 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 2 INT2EP: External Interrupt 2 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 1 INT1EP: External Interrupt 1 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 0 INT0EP: External Interrupt 0 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge  2010 Microchip Technology Inc. DS39905E-page 77

PIC24FJ256GA110 FAMILY REGISTER 7-5: IFS0: INTERRUPT FLAG STATUS REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — AD1IF U1TXIF U1RXIF SPI1IF SPF1IF T3IF bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 T2IF OC2IF IC2IF — T1IF OC1IF IC1IF INT0IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 AD1IF: A/D Conversion Complete Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12 U1TXIF: UART1 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 11 U1RXIF: UART1 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 10 SPI1IF: SPI1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 9 SPF1IF: SPI1 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8 T3IF: Timer3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7 T2IF: Timer2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 6 OC2IF: Output Compare Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 5 IC2IF: Input Capture Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4 Unimplemented: Read as ‘0’ bit 3 T1IF: Timer1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 OC1IF: Output Compare Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 IC1IF: Input Capture Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 INT0IF: External Interrupt 0 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS39905E-page 78  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-6: IFS1: INTERRUPT FLAG STATUS REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U2TXIF U2RXIF INT2IF T5IF T4IF OC4IF OC3IF — bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IC8IF IC7IF — INT1IF CNIF CMIF MI2C1IF SI2C1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 U2TXIF: UART2 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 14 U2RXIF: UART2 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 13 INT2IF: External Interrupt 2 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12 T5IF: Timer5 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 11 T4IF: Timer4 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 10 OC4IF: Output Compare Channel 4 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 9 OC3IF: Output Compare Channel 3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8 Unimplemented: Read as ‘0’ bit 7 IC8IF: Input Capture Channel 8 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 6 IC7IF: Input Capture Channel 7 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 5 Unimplemented: Read as ‘0’ bit 4 INT1IF: External Interrupt 1 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 3 CNIF: Input Change Notification Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 CMIF: Comparator Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 MI2C1IF: Master I2C1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 SI2C1IF: Slave I2C1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred  2010 Microchip Technology Inc. DS39905E-page 79

PIC24FJ256GA110 FAMILY REGISTER 7-7: IFS2: INTERRUPT FLAG STATUS REGISTER 2 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — PMPIF OC8IF OC7IF OC6IF OC5IF IC6IF bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 IC5IF IC4IF IC3IF — — — SPI2IF SPF2IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 PMPIF: Parallel Master Port Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12 OC8IF: Output Compare Channel 8 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 11 OC7IF: Output Compare Channel 7 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 10 OC6IF: Output Compare Channel 6 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 9 OC5IF: Output Compare Channel 5 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8 IC6IF: Input Capture Channel 6 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7 IC5IF: Input Capture Channel 5 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 6 IC4IF: Input Capture Channel 4 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 5 IC3IF: Input Capture Channel 3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4-2 Unimplemented: Read as ‘0’ bit 1 SPI2IF: SPI2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 SPF2IF: SPI2 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS39905E-page 80  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-8: IFS3: INTERRUPT FLAG STATUS REGISTER 3 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 — RTCIF — — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 U-0 — INT4IF INT3IF — — MI2C2IF SI2C2IF — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14 RTCIF: Real-Time Clock/Calendar Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 13-7 Unimplemented: Read as ‘0’ bit 6 INT4IF: External Interrupt 4 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 5 INT3IF: External Interrupt 3 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4-3 Unimplemented: Read as ‘0’ bit 2 MI2C2IF: Master I2C2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 SI2C2IF: Slave I2C2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 81

PIC24FJ256GA110 FAMILY REGISTER 7-9: IFS4: INTERRUPT FLAG STATUS REGISTER 4 U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 — — CTMUIF — — — — LVDIF bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 — — — — CRCIF U2ERIF U1ERIF — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 CTMUIF: CTMU Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12-9 Unimplemented: Read as ‘0’ bit 8 LVDIF: Low-Voltage Detect Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7-4 Unimplemented: Read as ‘0’ bit 3 CRCIF: CRC Generator Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 U2ERIF: UART2 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 U1ERIF: UART1 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 Unimplemented: Read as ‘0’ DS39905E-page 82  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-10: IFS5: INTERRUPT FLAG STATUS REGISTER 5 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — IC9IF OC9IF SPI3IF SPF3IF U4TXIF U4RXIF bit 15 bit 8 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U4ERIF — MI2C3IF SI2C3IF U3TXIF U3RXIF U3ERIF — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 IC9IF: Input Capture Channel 9 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12 OC9IF: Output Compare Channel 9 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 11 SPI3IF: SPI3 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 10 SPF3IF: SPI3 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 9 U4TXIF: UART4 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8 U4RXIF: UART4 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7 U4ERIF: UART4 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 6 Unimplemented: Read as ‘0’ bit 5 MI2C3IF: Master I2C3 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4 SI2C3IF: Slave I2C3 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 3 U3TXIF: UART3 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 U3RXIF: UART3 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 U3ERIF: UART3 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 83

PIC24FJ256GA110 FAMILY REGISTER 7-11: IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — AD1IE U1TXIE U1RXIE SPI1IE SPF1IE T3IE bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 T2IE OC2IE IC2IE — T1IE OC1IE IC1IE INT0IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 AD1IE: A/D Conversion Complete Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 12 U1TXIE: UART1 Transmitter Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 11 U1RXIE: UART1 Receiver Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 10 SPI1IE: SPI1 Transfer Complete Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 9 SPF1IE: SPI1 Fault Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 8 T3IE: Timer3 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 7 T2IE: Timer2 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 6 OC2IE: Output Compare Channel 2 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 5 IC2IE: Input Capture Channel 2 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 4 Unimplemented: Read as ‘0’ bit 3 T1IE: Timer1 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 2 OC1IE: Output Compare Channel 1 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 1 IC1IE: Input Capture Channel 1 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 INT0IE: External Interrupt 0 Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled DS39905E-page 84  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-12: IEC1: INTERRUPT ENABLE CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U2TXIE U2RXIE INT2IE(1) T5IE T4IE OC4IE OC3IE — bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IC8IE IC7IE — INT1IE(1) CNIE CMIE MI2C1IE SI2C1IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 U2TXIE: UART2 Transmitter Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 14 U2RXIE: UART2 Receiver Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 13 INT2IE: External Interrupt 2 Enable bit(1) 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 12 T5IE: Timer5 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 11 T4IE: Timer4 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 10 OC4IE: Output Compare Channel 4 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 9 OC3IE: Output Compare Channel 3 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 8 Unimplemented: Read as ‘0’ bit 7 IC8IE: Input Capture Channel 8 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 6 IC7IE: Input Capture Channel 7 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 5 Unimplemented: Read as ‘0’ bit 4 INT1IE: External Interrupt 1 Enable bit(1) 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 3 CNIE: Input Change Notification Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 2 CMIE: Comparator Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled Note 1: If an external interrupt is enabled, the interrupt input must also be configured to an available RPn or RPIn pin. See Section10.4 “Peripheral Pin Select” for more information.  2010 Microchip Technology Inc. DS39905E-page 85

PIC24FJ256GA110 FAMILY REGISTER 7-12: IEC1: INTERRUPT ENABLE CONTROL REGISTER 1 (CONTINUED) bit 1 MI2C1IE: Master I2C1 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 SI2C1IE: Slave I2C1 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled Note 1: If an external interrupt is enabled, the interrupt input must also be configured to an available RPn or RPIn pin. See Section10.4 “Peripheral Pin Select” for more information. DS39905E-page 86  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-13: IEC2: INTERRUPT ENABLE CONTROL REGISTER 2 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — PMPIE OC8IE OC7IE OC6IE OC5IE IC6IE bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 IC5IE IC4IE IC3IE — — — SPI2IE SPF2IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 PMPIE: Parallel Master Port Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 12 OC8IE: Output Compare Channel 8 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 11 OC7IE: Output Compare Channel 7 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 10 OC6IE: Output Compare Channel 6 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 9 OC5IE: Output Compare Channel 5 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 8 IC6IE: Input Capture Channel 6 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 7 IC5IE: Input Capture Channel 5 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 6 IC4IE: Input Capture Channel 4 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 5 IC3IE: Input Capture Channel 3 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 4-2 Unimplemented: Read as ‘0’ bit 1 SPI2IE: SPI2 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 SPF2IE: SPI2 Fault Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled  2010 Microchip Technology Inc. DS39905E-page 87

PIC24FJ256GA110 FAMILY REGISTER 7-14: IEC3: INTERRUPT ENABLE CONTROL REGISTER 3 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 — RTCIE — — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 U-0 — INT4IE(1) INT3IE(1) — — MI2C2IE SI2C2IE — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14 RTCIE: Real-Time Clock/Calendar Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 13-7 Unimplemented: Read as ‘0’ bit 6 INT4IE: External Interrupt 4 Enable bit(1) 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 5 INT3IE: External Interrupt 3 Enable bit(1) 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 4-3 Unimplemented: Read as ‘0’ bit 2 MI2C2IE: Master I2C2 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 1 SI2C2IE: Slave I2C2 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 Unimplemented: Read as ‘0’ Note 1: If an external interrupt is enabled, the interrupt input must also be configured to an available RPn or RPIn pin. See Section10.4 “Peripheral Pin Select” for more information. DS39905E-page 88  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-15: IEC4: INTERRUPT ENABLE CONTROL REGISTER 4 U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 — — CTMUIE — — — — LVDIE bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 — — — — CRCIE U2ERIE U1ERIE — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 CTMUIE: CTMU Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 12-9 Unimplemented: Read as ‘0’ bit 8 LVDIE: Low-Voltage Detect Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 7-4 Unimplemented: Read as ‘0’ bit 3 CRCIE: CRC Generator Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 2 U2ERIE: UART2 Error Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 1 U1ERIE: UART1 Error Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 89

PIC24FJ256GA110 FAMILY REGISTER 7-16: IEC5: INTERRUPT ENABLE CONTROL REGISTER 5 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — IC9IE OC9IE SPI3IE SPF3IE U4TXIE U4RXIE bit 15 bit 8 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U4ERIE — MI2C3IE SI2C3IE U3TXIE U3RXIE U3ERIE — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 IC9IE: Input Capture Channel 9 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 12 OC9IE: Output Compare Channel 9 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 11 SPI3IE: SPI3 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 10 SPF3IE: SPI3 Fault Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 9 U4TXIE: UART4 Transmitter Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 8 U4RXIE: UART4 Receiver Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 7 U4ERIE: UART4 Error Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 6 Unimplemented: Read as ‘0’ bit 5 MI2C3IE: Master I2C3 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 4 SI2C3IE: Slave I2C3 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 3 U3TXIE: UART3 Transmitter Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 2 U3RXIE: UART3 Receiver Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 1 U3ERIE: UART3 Error Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 Unimplemented: Read as ‘0’ DS39905E-page 90  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-17: IPC0: INTERRUPT PRIORITY CONTROL REGISTER 0 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — T1IP2 T1IP1 T1IP0 — OC1IP2 OC1IP1 OC1IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — IC1IP2 IC1IP1 IC1IP0 — INT0IP2 INT0IP1 INT0IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 T1IP<2:0>: Timer1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 OC1IP<2:0>: Output Compare Channel 1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 IC1IP<2:0>: Input Capture Channel 1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 INT0IP<2:0>: External Interrupt 0 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled  2010 Microchip Technology Inc. DS39905E-page 91

PIC24FJ256GA110 FAMILY REGISTER 7-18: IPC1: INTERRUPT PRIORITY CONTROL REGISTER 1 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — T2IP2 T2IP1 T2IP0 — OC2IP2 OC2IP1 OC2IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — IC2IP2 IC2IP1 IC2IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 T2IP<2:0>: Timer2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 OC2IP<2:0>: Output Compare Channel 2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 IC2IP<2:0>: Input Capture Channel 2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39905E-page 92  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-19: IPC2: INTERRUPT PRIORITY CONTROL REGISTER 2 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — U1RXIP2 U1RXIP1 U1RXIP0 — SPI1IP2 SPI1IP1 SPI1IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — SPF1IP2 SPF1IP1 SPF1IP0 — T3IP2 T3IP1 T3IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 U1RXIP<2:0>: UART1 Receiver Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 SPI1IP<2:0>: SPI1 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 SPF1IP<2:0>: SPI1 Fault Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 T3IP<2:0>: Timer3 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled  2010 Microchip Technology Inc. DS39905E-page 93

PIC24FJ256GA110 FAMILY REGISTER 7-20: IPC3: INTERRUPT PRIORITY CONTROL REGISTER 3 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — AD1IP2 AD1IP1 AD1IP0 — U1TXIP2 U1TXIP1 U1TXIP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 AD1IP<2:0>: A/D Conversion Complete Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 U1TXIP<2:0>: UART1 Transmitter Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled DS39905E-page 94  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-21: IPC4: INTERRUPT PRIORITY CONTROL REGISTER 4 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — CNIP2 CNIP1 CNIP0 — CMIP2 CMIP1 CMIP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — MI2C1IP2 MI2C1IP1 MI2C1IP0 — SI2C1IP2 SI2C1IP1 SI2C1IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 CNIP<2:0>: Input Change Notification Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 CMIP<2:0>: Comparator Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 MI2C1IP<2:0>: Master I2C1 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 SI2C1IP<2:0>: Slave I2C1 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled  2010 Microchip Technology Inc. DS39905E-page 95

PIC24FJ256GA110 FAMILY REGISTER 7-22: IPC5: INTERRUPT PRIORITY CONTROL REGISTER 5 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — IC8IP2 IC8IP1 IC8IP0 — IC7IP2 IC7IP1 IC7IP0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — INT1IP2 INT1IP1 INT1IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 IC8IP<2:0>: Input Capture Channel 8 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 IC7IP<2:0>: Input Capture Channel 7 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7-3 Unimplemented: Read as ‘0’ bit 2-0 INT1IP<2:0>: External Interrupt 1 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled DS39905E-page 96  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-23: IPC6: INTERRUPT PRIORITY CONTROL REGISTER 6 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — T4IP2 T4IP1 T4IP0 — OC4IP2 OC4IP1 OC4IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — OC3IP2 OC3IP1 OC3IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 T4IP<2:0>: Timer4 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 OC4IP<2:0>: Output Compare Channel 4 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 OC3IP<2:0>: Output Compare Channel 3 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 97

PIC24FJ256GA110 FAMILY REGISTER 7-24: IPC7: INTERRUPT PRIORITY CONTROL REGISTER 7 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — U2TXIP2 U2TXIP1 U2TXIP0 — U2RXIP2 U2RXIP1 U2RXIP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — INT2IP2 INT2IP1 INT2IP0 — T5IP2 T5IP1 T5IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 U2TXIP<2:0>: UART2 Transmitter Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 U2RXIP<2:0>: UART2 Receiver Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 INT2IP<2:0>: External Interrupt 2 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 T5IP<2:0>: Timer5 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled DS39905E-page 98  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-25: IPC8: INTERRUPT PRIORITY CONTROL REGISTER 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — SPI2IP2 SPI2IP1 SPI2IP0 — SPF2IP2 SPF2IP1 SPF2IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 SPI2IP<2:0>: SPI2 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 SPF2IP<2:0>: SPI2 Fault Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled  2010 Microchip Technology Inc. DS39905E-page 99

PIC24FJ256GA110 FAMILY REGISTER 7-26: IPC9: INTERRUPT PRIORITY CONTROL REGISTER 9 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — IC5IP2 IC5IP1 IC5IP0 — IC4IP2 IC4IP1 IC4IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — IC3IP2 IC3IP1 IC3IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 IC5IP<2:0>: Input Capture Channel 5 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 IC4IP<2:0>: Input Capture Channel 4 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 IC3IP<2:0>: Input Capture Channel 3 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39905E-page 100  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-27: IPC10: INTERRUPT PRIORITY CONTROL REGISTER 10 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — OC7IP2 OC7IP1 OC7IP0 — OC6IP2 OC6IP1 OC6IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — OC5IP2 OC5IP1 OC5IP0 — IC6IP2 IC6IP1 IC6IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 OC7IP<2:0>: Output Compare Channel 7 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 OC6IP<2:0>: Output Compare Channel 6 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 OC5IP<2:0>: Output Compare Channel 5 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 IC6IP<2:0>: Input Capture Channel 6 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled  2010 Microchip Technology Inc. DS39905E-page 101

PIC24FJ256GA110 FAMILY REGISTER 7-28: IPC11: INTERRUPT PRIORITY CONTROL REGISTER 11 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — PMPIP2 PMPIP1 PMPIP0 — OC8IP2 OC8IP1 OC8IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 PMPIP<2:0>: Parallel Master Port Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 OC8IP<2:0>: Output Compare Channel 8 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled DS39905E-page 102  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-29: IPC12: INTERRUPT PRIORITY CONTROL REGISTER 12 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — MI2C2IP2 MI2C2IP1 MI2C2IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — SI2C2IP2 SI2C2IP1 SI2C2IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 MI2C2IP<2:0>: Master I2C2 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 SI2C2IP<2:0>: Slave I2C2 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 103

PIC24FJ256GA110 FAMILY REGISTER 7-30: IPC13: INTERRUPT PRIORITY CONTROL REGISTER 13 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — INT4IP2 INT4IP1 INT4IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — INT3IP2 INT3IP1 INT3IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 INT4IP<2:0>: External Interrupt 4 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 INT3IP<2:0>: External Interrupt 3 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39905E-page 104  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-31: IPC15: INTERRUPT PRIORITY CONTROL REGISTER 15 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — RTCIP2 RTCIP1 RTCIP0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 RTCIP<2:0>: Real-Time Clock/Calendar Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7-0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 105

PIC24FJ256GA110 FAMILY REGISTER 7-32: IPC16: INTERRUPT PRIORITY CONTROL REGISTER 16 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — CRCIP2 CRCIP1 CRCIP0 — U2ERIP2 U2ERIP1 U2ERIP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — U1ERIP2 U1ERIP1 U1ERIP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 CRCIP<2:0>: CRC Generator Error Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 U2ERIP<2:0>: UART2 Error Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 U1ERIP<2:0>: UART1 Error Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39905E-page 106  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-33: IPC18: INTERRUPT PRIORITY CONTROL REGISTER 18 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — LVDIP2 LVDIP1 LVDIP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-3 Unimplemented: Read as ‘0’ bit 2-0 LVDIP<2:0>: Low-Voltage Detect Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled REGISTER 7-34: IPC19: INTERRUPT PRIORITY CONTROL REGISTER 19 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — CTMUIP2 CTMUIP1 CTMUIP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 CTMUIP<2:0>: CTMU Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 107

PIC24FJ256GA110 FAMILY REGISTER 7-35: IPC20: INTERRUPT PRIORITY CONTROL REGISTER 20 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — U3TXIP2 U3TXIP1 U3TXIP0 — U3RXIP2 U3RXIP1 U3RXIP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — U3ERIP2 U3ERIP1 U3ERIP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 U3TXIP<2:0>: UART3 Transmitter Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 U3RXIP<2:0>: UART3 Receiver Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 U3ERIP<2:0>: UART3 Error Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39905E-page 108  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-36: IPC21: INTERRUPT PRIORITY CONTROL REGISTER 21 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — U4ERIP2 U4ERIP1 U4ERIP0 — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — MI2C3IP2 MI2C3IP1 MI2C3IP0 — SI2C3IP2 SI2C3IP1 SI2C3PI0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 U4ERIP<2:0>: UART4 Error Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11-7 Unimplemented: Read as ‘0’ bit 6-4 MI2C3IP<2:0:> Master I2C3 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 SI2C3IP<2:0>: Slave I2C3 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled  2010 Microchip Technology Inc. DS39905E-page 109

PIC24FJ256GA110 FAMILY REGISTER 7-37: IPC22: INTERRUPT PRIORITY CONTROL REGISTER 22 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — SPI3IP2 SPI3IP1 SPI3IP0 — SPF3IP2 SPF3IP1 SPF3IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — U4TXIP2 U4TXIP1 U4TXIP0 — U4RXIP2 U4RXIP1 U4RXIP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 SPI3IP<2:0>: SPI3 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 SPF3IP<2:0>: SPI3 Fault Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 U4TXIP<2:0>: UART4 Transmitter Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 U4RXIP<2:0>: UART4 Receiver Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled DS39905E-page 110  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 7-38: IPC23: INTERRUPT PRIORITY CONTROL REGISTER 23 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — IC9IP2 IC9IP1 IC9IP0 — OC9IP2 OC9IP1 OC9IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 IC9IP<2:0>: Input Capture Channel 9 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 OC9IP<2:0>: Output Compare Channel 9 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) • • • 001 = Interrupt is priority 1 000 = Interrupt source is disabled  2010 Microchip Technology Inc. DS39905E-page 111

PIC24FJ256GA110 FAMILY REGISTER 7-39: INTTREG: INTERRUPT CONTROL AND STATUS REGISTER R-0 U-0 R/W-0 U-0 R-0 R-0 R-0 R-0 CPUIRQ — VHOLD — ILR3 ILR2 ILR1 ILR0 bit 15 bit 8 U-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 — VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CPUIRQ: Interrupt Request from Interrupt Controller CPU bit 1 = An interrupt request has occurred but has not yet been Acknowledged by the CPU; this happens when the CPU priority is higher than the interrupt priority 0 = No interrupt request is unacknowledged bit 14 Unimplemented: Read as ‘0’ bit 13 VHOLD: Vector Number Capture Configuration bit 1 = VECNUM bits contain the value of the highest priority pending interrupt 0 = VECNUM bits contain the value of the last Acknowledged interrupt (i.e., the last interrupt that has occurred with higher priority than the CPU, even if other interrupts are pending) bit 12 Unimplemented: Read as ‘0’ bit 11-8 ILR<3:0>: New CPU Interrupt Priority Level bits 1111 = CPU interrupt priority level is 15 • • • 0001 = CPU interrupt priority level is 1 0000 = CPU interrupt priority level is 0 bit 7 Unimplemented: Read as ‘0’ bit 6-0 VECNUM<6:0>: Pending Interrupt Vector ID bits (pending vector number is VECNUM + 8) 0111111 = Interrupt vector pending is number 135 • • • 0000001 = Interrupt vector pending is number 9 0000000 = Interrupt vector pending is number 8 DS39905E-page 112  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 7.4 Interrupt Setup Procedures 7.4.3 TRAP SERVICE ROUTINE A Trap Service Routine (TSR) is coded like an ISR, 7.4.1 INITIALIZATION except that the appropriate trap status flag in the To configure an interrupt source: INTCON1 register must be cleared to avoid re-entry into the TSR. 1. Set the NSTDIS control bit (INTCON1<15>) if nested interrupts are not desired. 7.4.4 INTERRUPT DISABLE 2. Select the user-assigned priority level for the interrupt source by writing the control bits in the All user interrupts can be disabled using the following appropriate IPCx register. The priority level will procedure: depend on the specific application and type of 1. Push the current SR value onto the software interrupt source. If multiple priority levels are not stack using the PUSH instruction. desired, the IPCx register control bits for all 2. Force the CPU to priority level 7 by inclusive enabled interrupt sources may be programmed ORing the value E0h with SRL. to the same non-zero value. To enable user interrupts, the POP instruction may be Note: At a device Reset, the IPCx registers are used to restore the previous SR value. initialized, such that all user interrupt Note that only user interrupts with a priority level of 7 or sources are assigned to priority level 4. less can be disabled. Trap sources (level8-15) cannot 3. Clear the interrupt status flag bit associated with be disabled. the peripheral in the associated IFSx register. The DISI instruction provides a convenient way to 4. Enable the interrupt source by setting the disable interrupts of priority levels 1-6 for a fixed period interrupt enable control bit associated with the of time. Level 7 interrupt sources are not disabled by source in the appropriate IECx register. the DISI instruction. 7.4.2 INTERRUPT SERVICE ROUTINE The method that is used to declare an ISR and initialize the IVT with the correct vector address will depend on the programming language (i.e., ‘C’ or assembler) and the language development toolsuite that is used to develop the application. In general, the user must clear the interrupt flag in the appropriate IFSx register for the source of the interrupt that the ISR handles. Otherwise, the ISR will be re-entered immediately after exiting the routine. If the ISR is coded in assembly language, it must be terminated using a RETFIE instruction to unstack the saved PC value, SRL value and old CPU priority level.  2010 Microchip Technology Inc. DS39905E-page 113

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 114  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 8.0 OSCILLATOR • Software-controllable switching between various CONFIGURATION clock sources • Software-controllable postscaler for selective Note: This data sheet summarizes the features of clocking of CPU for system power savings this group of PIC24F devices. It is not • A Fail-Safe Clock Monitor (FSCM) that detects intended to be a comprehensive reference clock failure and permits safe application recovery source. For more information, refer to the or shutdown “PIC24F Family Reference Manual”, • A separate and independently configurable system Section 6. “Oscillator” (DS39700). clock output for synchronizing external hardware The oscillator system for PIC24FJ256GA110 family A simplified diagram of the oscillator system is shown devices has the following features: in Figure8-1. • A total of four external and internal oscillator options as clock sources, providing 11 different clock modes • On-chip 4x PLL to boost internal operating frequency on select internal and external oscillator sources FIGURE 8-1: PIC24FJ256GA110 FAMILY CLOCK DIAGRAM Primary Oscillator REFOCON<15:8> XT, HS, EC OSCO Reference Clock Generator XTPLL, HSPLL OSCI ECPLL,FRCPLL 4 x PLL REFO 8 MHz er 4 MHz FRC al FRCDIV c Oscillator 8 MHz sts (nominal) Po Peripherals DIV/2 (FCY) CLKDIV<10:8> FRC CLKO LPRC LPRC Oscillator 31 kHz (nominal) aler CPU c s st Secondary Oscillator o P SOSC SOSCO CLKDIV<14:12> SOSCEN Enable SOSCI Oscillator Clock Control Logic Fail-Safe Clock Monitor WDT, PWRT Clock Source Option for Other Modules  2010 Microchip Technology Inc. DS39905E-page 115

PIC24FJ256GA110 FAMILY 8.1 CPU Clocking Scheme 8.2 Initial Configuration on POR The system clock source can be provided by one of The oscillator source (and operating mode) that is used four sources: at a device Power-on Reset event is selected using Configuration bit settings. The oscillator Configuration • Primary Oscillator (POSC) on the OSCI and bit settings are located in the Configuration registers in OSCO pins the program memory (refer to Section25.1 “Configu- • Secondary Oscillator (SOSC) on the SOSCI and ration Bits” for further details). The Primary SOSCO pins Oscillator Configuration bits, POSCMD<1:0> • Fast Internal RC (FRC) Oscillator (ConfigurationWord2<1:0>), and the Initial Oscillator • Low-Power Internal RC (LPRC) Oscillator Select Configuration bits, FNOSC<2:0> The Primary Oscillator and FRC sources have the (ConfigurationWord2<10:8>), select the oscillator option of using the internal 4x PLL. The frequency of source that is used at a Power-on Reset. The FRC the FRC clock source can optionally be reduced by the Primary Oscillator with Postscaler (FRCDIV) is the programmable clock divider. The selected clock source default (unprogrammed) selection. The Secondary generates the processor and peripheral clock sources. Oscillator, or one of the internal oscillators, may be chosen by programming these bit locations. The processor clock source is divided by two to pro- duce the internal instruction cycle clock, FCY. In this The Configuration bits allow users to choose between document, the instruction cycle clock is also denoted the various clock modes, shown in Table8-1. by FOSC/2. The internal instruction cycle clock, FOSC/2, 8.2.1 CLOCK SWITCHING MODE can be provided on the OSCO I/O pin for some CONFIGURATION BITS operating modes of the Primary Oscillator. The FCKSM Configuration bits (Configuration Word2<7:6>) are used to jointly configure device clock switching and the Fail-Safe Clock Monitor (FSCM). Clock switching is enabled only when FCKSM1 is programmed (‘0’). The FSCM is enabled only when FCKSM<1:0> are both programmed (‘00’). TABLE 8-1: CONFIGURATION BIT VALUES FOR CLOCK SELECTION Oscillator Mode Oscillator Source POSCMD<1:0> FNOSC<2:0> Note Fast RC Oscillator with Postscaler Internal 11 111 1, 2 (FRCDIV) (Reserved) Internal xx 110 1 Low-Power RC Oscillator (LPRC) Internal 11 101 1 Secondary (Timer1) Oscillator Secondary 11 100 1 (SOSC) Primary Oscillator (XT) with PLL Primary 01 011 Module (XTPLL) Primary Oscillator (EC) with PLL Primary 00 011 Module (ECPLL) Primary Oscillator (HS) Primary 10 010 Primary Oscillator (XT) Primary 01 010 Primary Oscillator (EC) Primary 00 010 Fast RC Oscillator with PLL Module Internal 11 001 1 (FRCPLL) Fast RC Oscillator (FRC) Internal 11 000 1 Note 1: OSCO pin function is determined by the OSCIOFCN Configuration bit. 2: This is the default oscillator mode for an unprogrammed (erased) device. DS39905E-page 116  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 8.3 Control Registers The CLKDIV register (Register8-2) controls the features associated with Doze mode, as well as the The operation of the oscillator is controlled by three postscaler for the FRC Oscillator. Special Function Registers (SFRs): The OSCTUN register (Register8-3) allows the user to • OSCCON fine tune the FRC Oscillator over a range of approxi- • CLKDIV mately ±12%. • OSCTUN The OSCCON register (Register8-1) is the main con- trol register for the oscillator. It controls clock source switching and allows the monitoring of clock sources. REGISTER 8-1: OSCCON: OSCILLATOR CONTROL REGISTER U-0 R-0 R-0 R-0 U-0 R/W-x(1) R/W-x(1) R/W-x(1) — COSC2 COSC1 COSC0 — NOSC2 NOSC1 NOSC0 bit 15 bit 8 R/SO-0 R/W-0 R-0(3) U-0 R/CO-0 R/W-0 R/W-0 R/W-0 CLKLOCK IOLOCK(2) LOCK — CF POSCEN SOSCEN OSWEN bit 7 bit 0 Legend: CO = Clearable Only bit SO = Settable Only bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 COSC<2:0>: Current Oscillator Selection bits 111 = Fast RC Oscillator with Postscaler (FRCDIV) 110 = Reserved 101 = Low-Power RC Oscillator (LPRC) 100 = Secondary Oscillator (SOSC) 011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = Fast RC Oscillator with Postscaler and PLL module (FRCPLL) 000 = Fast RC Oscillator (FRC) bit 11 Unimplemented: Read as ‘0’ bit 10-8 NOSC<2:0>: New Oscillator Selection bits(1) 111 = Fast RC Oscillator with Postscaler (FRCDIV) 110 = Reserved 101 = Low-Power RC Oscillator (LPRC) 100 = Secondary Oscillator (SOSC) 011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = Fast RC Oscillator with Postscaler and PLL module (FRCPLL) 000 = Fast RC Oscillator (FRC) Note 1: Reset values for these bits are determined by the FNOSC Configuration bits. 2: The state of the IOLOCK bit can only be changed once an unlocking sequence has been executed. In addition, if the IOL1WAY Configuration bit is ‘1’ once the IOLOCK bit is set, it cannot be cleared. 3: Also, resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected.  2010 Microchip Technology Inc. DS39905E-page 117

PIC24FJ256GA110 FAMILY REGISTER 8-1: OSCCON: OSCILLATOR CONTROL REGISTER (CONTINUED) bit 7 CLKLOCK: Clock Selection Lock Enabled bit If FSCM is enabled (FCKSM1 = 1): 1 = Clock and PLL selections are locked 0 = Clock and PLL selections are not locked and may be modified by setting the OSWEN bit If FSCM is disabled (FCKSM1 = 0): Clock and PLL selections are never locked and may be modified by setting the OSWEN bit. bit 6 IOLOCK: I/O Lock Enable bit(2) 1 = I/O lock is active 0 = I/O lock is not active bit 5 LOCK: PLL Lock Status bit(3) 1 = PLL module is in lock or PLL module start-up timer is satisfied 0 = PLL module is out of lock, PLL start-up timer is running or PLL is disabled bit 4 Unimplemented: Read as ‘0’ bit 3 CF: Clock Fail Detect bit 1 = FSCM has detected a clock failure 0 = No clock failure has been detected bit 2 POSCEN: Primary Oscillator Sleep Enable bit 1 = Primary Oscillator continues to operate during Sleep mode 0 = Primary Oscillator disabled during Sleep mode bit 1 SOSCEN: 32kHz Secondary Oscillator (SOSC) Enable bit 1 = Enable Secondary Oscillator 0 = Disable Secondary Oscillator bit 0 OSWEN: Oscillator Switch Enable bit 1 = Initiate an oscillator switch to clock source specified by NOSC<2:0> bits 0 = Oscillator switch is complete Note 1: Reset values for these bits are determined by the FNOSC Configuration bits. 2: The state of the IOLOCK bit can only be changed once an unlocking sequence has been executed. In addition, if the IOL1WAY Configuration bit is ‘1’ once the IOLOCK bit is set, it cannot be cleared. 3: Also, resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected. DS39905E-page 118  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 8-2: CLKDIV: CLOCK DIVIDER REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 ROI DOZE2 DOZE1 DOZE0 DOZEN(1) RCDIV2 RCDIV1 RCDIV0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROI: Recover on Interrupt bit 1 = Interrupts clear the DOZEN bit and reset the CPU peripheral clock ratio to 1:1 0 = Interrupts have no effect on the DOZEN bit bit 14-12 DOZE<2:0>: CPU Peripheral Clock Ratio Select bits 111 = 1:128 110 = 1:64 101 = 1:32 100 = 1:16 011 = 1:8 010 = 1:4 001 = 1:2 000 = 1:1 bit 11 DOZEN: DOZE Enable bit(1) 1 = DOZE<2:0> bits specify the CPU peripheral clock ratio 0 = CPU peripheral clock ratio set to 1:1 bit 10-8 RCDIV<2:0>: FRC Postscaler Select bits 111 = 31.25kHz (divide by 256) 110 = 125kHz (divide by 64) 101 = 250kHz (divide by 32) 100 = 500kHz (divide by 16) 011 = 1MHz (divide by 8) 010 = 2MHz (divide by 4) 001 = 4MHz (divide by 2) 000 = 8MHz (divide by 1) bit 7-0 Unimplemented: Read as ‘0’ Note 1: This bit is automatically cleared when the ROI bit is set and an interrupt occurs.  2010 Microchip Technology Inc. DS39905E-page 119

PIC24FJ256GA110 FAMILY REGISTER 8-3: OSCTUN: FRC OSCILLATOR TUNE REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — TUN5(1) TUN4(1) TUN3(1) TUN2(1) TUN1(1) TUN0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5-0 TUN<5:0>: FRC Oscillator Tuning bits(1) 011111 = Maximum frequency deviation 011110 =    000001 = 000000 = Center frequency, oscillator is running at factory calibrated frequency 111111 =    100001 = 100000 = Minimum frequency deviation Note 1: Increments or decrements of TUN<5:0> may not change the FRC frequency in equal steps over the FRC tuning range and may not be monotonic. 8.4 Clock Switching Operation 8.4.1 ENABLING CLOCK SWITCHING With few limitations, applications are free to switch To enable clock switching, the FCKSM1 Configuration between any of the four clock sources (POSC, SOSC, bit in CW 2 must be programmed to ‘0’. (Refer to FRC and LPRC) under software control and at any Section25.1 “Configuration Bits” for further details.) time. To limit the possible side effects that could result If the FCKSM1 Configuration bit is unprogrammed (‘1’), from this flexibility, PIC24F devices have a safeguard the clock switching function and Fail-Safe Clock Monitor lock built into the switching process. function are disabled; this is the default setting. The NOSCx control bits (OSCCON<10:8>) do not Note: The Primary Oscillator mode has three control the clock selection when clock switching is dis- different submodes (XT, HS and EC) abled. However, the COSCx bits (OSCCON<14:12>) which are determined by the POSCMDx will reflect the clock source selected by the FNOSCx Configuration bits. While an application Configuration bits. can switch to and from Primary Oscillator mode in software, it cannot switch The OSWEN control bit (OSCCON<0>) has no effect between the different primary submodes when clock switching is disabled; it is held at ‘0’ at all without reprogramming the device. times. DS39905E-page 120  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 8.4.2 OSCILLATOR SWITCHING A recommended code sequence for a clock switch SEQUENCE includes the following: At a minimum, performing a clock switch requires this 1. Disable interrupts during the OSCCON register basic sequence: unlock and write sequence. 2. Execute the unlock sequence for the OSCCON 1. If desired, read the COSCx bits high byte by writing 78h and 9Ah to (OSCCON<14:12>) to determine the current OSCCON<15:8> in two back-to-back oscillator source. instructions. 2. Perform the unlock sequence to allow a write to 3. Write new oscillator source to the NOSCx bits in the OSCCON register high byte. the instruction immediately following the unlock 3. Write the appropriate value to the NOSCx bits sequence. (OSCCON<10:8>) for the new oscillator source. 4. Execute the unlock sequence for the OSCCON 4. Perform the unlock sequence to allow a write to low byte by writing 46h and 57h to the OSCCON register low byte. OSCCON<7:0> in two back-to-back instructions. 5. Set the OSWEN bit to initiate the oscillator 5. Set the OSWEN bit in the instruction immediately switch. following the unlock sequence. Once the basic sequence is completed, the system 6. Continue to execute code that is not clock hardware responds automatically as follows: clock-sensitive (optional). 1. The clock switching hardware compares the 7. Invoke an appropriate amount of software delay COSCx bits with the new value of the NOSCx (cycle counting) to allow the selected oscillator bits. If they are the same, then the clock switch and/or PLL to start and stabilize. is a redundant operation. In this case, the 8. Check to see if OSWEN is ‘0’. If it is, the switch OSWEN bit is cleared automatically and the was successful. If OSWEN is still set, then check clock switch is aborted. the LOCK bit to determine the cause of failure. 2. If a valid clock switch has been initiated, the The core sequence for unlocking the OSCCON register LOCK (OSCCON<5>) and CF (OSCCON<3>) and initiating a clock switch is shown in Example8-1. bits are cleared. 3. The new oscillator is turned on by the hardware EXAMPLE 8-1: BASIC CODE SEQUENCE if it is not currently running. If a crystal oscillator FOR CLOCK SWITCHING must be turned on, the hardware will wait until the OST expires. If the new source is using the ;Place the new oscillator selection in W0 PLL, then the hardware waits until a PLL lock is ;OSCCONH (high byte) Unlock Sequence detected (LOCK = 1). MOV #OSCCONH, w1 MOV #0x78, w2 4. The hardware waits for 10 clock cycles from the MOV #0x9A, w3 new clock source and then performs the clock MOV.b w2, [w1] switch. MOV.b w3, [w1] 5. The hardware clears the OSWEN bit to indicate a ;Set new oscillator selection successful clock transition. In addition, the MOV.b WREG, OSCCONH NOSCx bit values are transferred to the COSCx ;OSCCONL (low byte) unlock sequence MOV #OSCCONL, w1 bits. MOV #0x46, w2 6. The old clock source is turned off at this time, MOV #0x57, w3 with the exception of LPRC (if WDT or FSCM is MOV.b w2, [w1] enabled) or SOSC (if SOSCEN remains set). MOV.b w3, [w1] ;Start oscillator switch operation Note1: The processor will continue to execute BSET OSCCON,#0 code throughout the clock switching sequence. Timing-sensitive code should not be executed during this time. EXAMPLE 8-2: BASIC CODE SEQUENCE 2: Direct clock switches between any FOR CLOCK SWITCHING Primary Oscillator mode with PLL and //Write new "value" to OSCCONH to FRCPLL mode are not permitted. This // set the new oscillator selection applies to clock switches in either direc- __builtin_write_OSCCONH(value); tion. In these instances, the application must switch to FRC mode as a transition //Set the OSWEN bit to start the oscillator clock source between the two PLL // switch operation modes. __builtin_write_OSCCONL(OSCCON | 0x01);  2010 Microchip Technology Inc. DS39905E-page 121

PIC24FJ256GA110 FAMILY 8.5 Reference Clock Output The ROSSLP and ROSEL bits (REFOCON<13:12>) control the availability of the reference output during In addition to the CLKO output (FOSC/2) available in Sleep mode. The ROSEL bit determines if the oscillator certain oscillator modes, the device clock in the on OSC1 and OSC2, or the current system clock source, PIC24FJ256GA110 family devices can also be config- is used for the reference clock output. The ROSSLP bit ured to provide a reference clock output signal to a port determines if the reference source is available on REFO pin. This feature is available in all oscillator configura- when the device is in Sleep mode. tions and allows the user to select a greater range of To use the reference clock output in Sleep mode, both clock submultiples to drive external devices in the the ROSSLP and ROSEL bits must be set. The device application. clock must also be configured for one of the Primary This reference clock output is controlled by the Oscillator modes (EC, HS or XT); otherwise, if the REFOCON register (Register8-4). Setting the ROEN POSCEN bit is also not set, the oscillator on OSC1 and bit (REFOCON<15>) makes the clock signal available OSC2 will be powered down when the device enters on the REFO pin. The RODIV bits (REFOCON<11:8>) Sleep mode. Clearing the ROSEL bit allows the refer- enable the selection of 16 different clock divider ence output frequency to change as the system clock options. changes during any clock switches. DS39905E-page 122  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 8-4: REFOCON: REFERENCE OSCILLATOR CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ROEN — ROSSLP ROSEL RODIV3 RODIV2 RODIV1 RODIV0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROEN: Reference Oscillator Output Enable bit 1 = Reference oscillator enabled on REFO pin 0 = Reference oscillator disabled bit 14 Unimplemented: Read as ‘0’ bit 13 ROSSLP: Reference Oscillator Output Stop in Sleep bit 1 = Reference oscillator continues to run in Sleep 0 = Reference oscillator is disabled in Sleep bit 12 ROSEL: Reference Oscillator Source Select bit 1 = Primary Oscillator used as the base clock. Note that the crystal oscillator must be enabled using the FOSC<2:0> bits; crystal maintains the operation in Sleep mode. 0 = System clock used as the base clock; base clock reflects any clock switching of the device bit 11-8 RODIV<3:0>: Reference Oscillator Divisor Select bits 1111 = Base clock value divided by 32,768 1110 = Base clock value divided by 16,384 1101 = Base clock value divided by 8,192 1100 = Base clock value divided by 4,096 1011 = Base clock value divided by 2,048 1010 = Base clock value divided by 1,024 1001 = Base clock value divided by 512 1000 = Base clock value divided by 256 0111 = Base clock value divided by 128 0110 = Base clock value divided by 64 0101 = Base clock value divided by 32 0100 = Base clock value divided by 16 0011 = Base clock value divided by 8 0010 = Base clock value divided by 4 0001 = Base clock value divided by 2 0000 = Base clock value bit 7-0 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 123

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 124  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 9.0 POWER-SAVING FEATURES Sleep and Idle modes can be exited as a result of an enabled interrupt, WDT time-out or a device Reset. Note: This data sheet summarizes the features of When the device exits these modes, it is said to this group of PIC24F devices. It is not “wake-up”. intended to be a comprehensive reference source. For more information, refer to the 9.2.1 SLEEP MODE “PIC24F Family Reference Manual”, Sleep mode has these features: Section 10. “Power-Saving Features” • The system clock source is shut down. If an (DS39698). on-chip oscillator is used, it is turned off. The PIC24FJ256GA110 family of devices provides the • The device current consumption will be reduced ability to manage power consumption by selectively to a minimum provided that no I/O pin is sourcing managing clocking to the CPU and the peripherals. In current. general, a lower clock frequency and a reduction in the • The Fail-Safe Clock Monitor does not operate number of circuits being clocked constitutes lower during Sleep mode since the system clock source consumed power. All PIC24F devices manage power is disabled. consumption in four different ways: • The LPRC clock will continue to run in Sleep • Clock frequency mode if the WDT is enabled. • Instruction-based Sleep and Idle modes • The WDT, if enabled, is automatically cleared • Software controlled Doze mode prior to entering Sleep mode. • Selective peripheral control in software • Some device features or peripherals may continue to operate in Sleep mode. This includes Combinations of these methods can be used to items such as the input change notification on the selectively tailor an application’s power consumption, I/O ports, or peripherals that use an external clock while still maintaining critical application features, such input. Any peripheral that requires the system as timing-sensitive communications. clock source for its operation will be disabled in Sleep mode. 9.1 Clock Frequency and Clock Additional power reductions can be achieved by Switching disabling the on-chip voltage regulator whenever Sleep PIC24F devices allow for a wide range of clock mode is invoked. This is done by clearing the PMSLP frequencies to be selected under application control. If bit (RCON<8>). Disabling the regulator adds an addi- the system clock configuration is not locked, users can tional delay of about 190s to the device wake-up choose low-power or high-precision oscillators by simply time. It is recommended that applications not using the changing the NOSC bits. The process of changing a voltage regulator leave the PMSLP bit set. For addi- system clock during operation, as well as limitations to tional details on the regulator and Sleep mode, see the process, are discussed in more detail in Section8.0 Section25.2.5 “Voltage Regulator Standby Mode”. “Oscillator Configuration”. The device will wake-up from Sleep mode on any of these events: 9.2 Instruction-Based Power-Saving • On any interrupt source that is individually Modes enabled PIC24F devices have two special power-saving modes • On any form of device Reset that are entered through the execution of a special • On a WDT time-out PWRSAV instruction. Sleep mode stops clock operation On wake-up from Sleep, the processor will restart with and halts all code execution; Idle mode halts the CPU the same clock source that was active when Sleep and code execution, but allows peripheral modules to mode was entered. continue operation. The assembly syntax of the PWRSAV instruction is shown in Example9-1. EXAMPLE 9-1: PWRSAV INSTRUCTION SYNTAX PWRSAV #0 ; Put the device into SLEEP mode PWRSAV #1 ; Put the device into IDLE mode  2010 Microchip Technology Inc. DS39905E-page 125

PIC24FJ256GA110 FAMILY 9.2.2 IDLE MODE It is also possible to use Doze mode to selectively reduce power consumption in event driven applica- Idle mode has these features: tions. This allows clock-sensitive functions, such as • The CPU will stop executing instructions. synchronous communications, to continue without • The WDT is automatically cleared. interruption while the CPU Idles, waiting for something • The system clock source remains active. By to invoke an interrupt routine. Enabling the automatic default, all peripheral modules continue to operate return to full-speed CPU operation on interrupts is normally from the system clock source, but can enabled by setting the ROI bit (CLKDIV<15>). By also be selectively disabled (see Section9.4 default, interrupt events have no effect on Doze mode “Selective Peripheral Module Control”). operation. • If the WDT or FSCM is enabled, the LPRC will 9.4 Selective Peripheral Module also remain active. Control The device will wake from Idle mode on any of these events: Idle and Doze modes allow users to substantially • Any interrupt that is individually enabled reduce power consumption by slowing or stopping the CPU clock. Even so, peripheral modules still remain • Any device Reset clocked and thus consume power. There may be cases • A WDT time-out where the application needs what these modes do not On wake-up from Idle, the clock is reapplied to the CPU provide: the allocation of power resources to CPU and instruction execution begins immediately, starting processing with minimal power consumption from the with the instruction following the PWRSAV instruction or peripherals. the first instruction in the ISR. PIC24F devices address this requirement by allowing 9.2.3 INTERRUPTS COINCIDENT WITH peripheral modules to be selectively disabled, reducing or eliminating their power consumption. This can be POWER SAVE INSTRUCTIONS done with two control bits: Any interrupt that coincides with the execution of a • The Peripheral Enable bit, generically named PWRSAV instruction will be held off until entry into Sleep “XXXEN”, located in the module’s main control or Idle mode has completed. The device will then SFR. wake-up from Sleep or Idle mode. • The Peripheral Module Disable (PMD) bit, generically named, “XXXMD”, located in one of 9.3 Doze Mode the PMD Control registers. Generally, changing clock speed and invoking one of Both bits have similar functions in enabling or disabling the power-saving modes are the preferred strategies its associated module. Setting the PMD bit for a module for reducing power consumption. There may be disables all clock sources to that module, reducing its circumstances, however, where this is not practical. For power consumption to an absolute minimum. In this example, it may be necessary for an application to state, the control and status registers associated with maintain uninterrupted synchronous communication, the peripheral will also be disabled, so writes to those even while it is doing nothing else. Reducing system registers will have no effect and read values will be clock speed may introduce communication errors, invalid. Many peripheral modules have a corresponding while using a power-saving mode may stop PMD bit. communications completely. In contrast, disabling a module by clearing its XXXEN Doze mode is a simple and effective alternative method bit disables its functionality, but leaves its registers to reduce power consumption while the device is still available to be read and written to. This reduces power executing code. In this mode, the system clock contin- consumption, but not by as much as setting the PMD ues to operate from the same source and at the same bit does. Most peripheral modules have an enable bit; speed. Peripheral modules continue to be clocked at exceptions include input capture, output compare and the same speed while the CPU clock speed is reduced. RTCC. Synchronization between the two clock domains is To achieve more selective power savings, peripheral maintained, allowing the peripherals to access the modules can also be selectively disabled when the SFRs while the CPU executes code at a slower rate. device enters Idle mode. This is done through the Doze mode is enabled by setting the DOZEN bit control bit of the generic name format, “XXXIDL”. By (CLKDIV<11>). The ratio between peripheral and core default, all modules that can operate during Idle mode clock speed is determined by the DOZE<2:0> bits will do so. Using the disable on Idle feature allows (CLKDIV<14:12>). There are eight possible further reduction of power consumption during Idle configurations, from 1:1 to 1:128, with 1:1 being the mode, enhancing power savings for extremely critical default. power applications. DS39905E-page 126  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 10.0 I/O PORTS When a peripheral is enabled and the peripheral is actively driving an associated pin, the use of the pin as Note: This data sheet summarizes the features of a general purpose output pin is disabled. The I/O pin this group of PIC24F devices. It is not may be read, but the output driver for the parallel port intended to be a comprehensive reference bit will be disabled. If a peripheral is enabled, but the source. For more information, refer to the peripheral is not actively driving a pin, that pin may be “PIC24F Family Reference Manual”, driven by a port. Section 12. “I/O Ports with Peripheral All port pins have three registers directly associated Pin Select (PPS)” (DS39711). with their operation as digital I/O. The Data Direction register (TRIS) determines whether the pin is an input All of the device pins (except VDD, VSS, MCLR and or an output. If the data direction bit is a ‘1’, then the pin OSCI/CLKI) are shared between the peripherals and is an input. All port pins are defined as inputs after a the parallel I/O ports. All I/O input ports feature Schmitt Reset. Reads from the Output Latch register (LAT), Trigger inputs for improved noise immunity. read the latch. Writes to the latch, write the latch. Reads from the port (PORT), read the port pins, while 10.1 Parallel I/O (PIO) Ports writes to the port pins, write the latch. A parallel I/O port that shares a pin with a peripheral is, Any bit and its associated data and control registers in general, subservient to the peripheral. The periph- that are not valid for a particular device will be eral’s output buffer data and control signals are disabled. That means the corresponding LAT and provided to a pair of multiplexers. The multiplexers TRIS registers and the port pin will read as zeros. select whether the peripheral or the associated port When a pin is shared with another peripheral or func- has ownership of the output data and control signals of tion that is defined as an input only, it is regarded as a the I/O pin. The logic also prevents “loop through”, in dedicated port because there is no other competing which a port’s digital output can drive the input of a source of outputs. peripheral that shares the same pin. Figure10-1 shows how ports are shared with other peripherals and the associated I/O pin to which they are connected. FIGURE 10-1: BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE Peripheral Module Output Multiplexers Peripheral Input Data Peripheral Module Enable I/O Peripheral Output Enable 1 Output Enable Peripheral Output Data 0 PIO Module 1 Output Data Read TRIS 0 Data Bus D Q I/O Pin WR TRIS CK TRIS Latch D Q WR LAT + CK WR PORT Data Latch Read LAT Input Data Read PORT  2010 Microchip Technology Inc. DS39905E-page 127

PIC24FJ256GA110 FAMILY 10.1.1 OPEN-DRAIN CONFIGURATION 10.2.2 ANALOG INPUT PINS AND VOLTAGE CONSIDERATIONS In addition to the PORT, LAT and TRIS registers for data control, each port pin can also be individually con- The voltage tolerance of pins used as device inputs is figured for either digital or open-drain output. This is dependent on the pin’s input function. Pins that are used controlled by the Open-Drain Control register, ODCx, as digital only inputs are able to handle DC voltages up associated with each port. Setting any of the bits con- to 5.5V, a level typical for digital logic circuits. In contrast, figures the corresponding pin to act as an open-drain pins that also have analog input functions of any kind output. can only tolerate voltages up to VDD. Voltage excursions The open-drain feature allows the generation of beyond VDD on these pins are always to be avoided. outputs higher than VDD (e.g., 5V) on any desired Table10-1 summarizes the input capabilities. Refer to digital only pins by using external pull-up resistors. The Section28.1 “DC Characteristics” for more details. maximum open-drain voltage allowed is the same as Note: For easy identification, the pin diagrams at the maximum VIH specification. the beginning of this data sheet also indicate 5.5V tolerant pins with dark grey 10.2 Configuring Analog Port Pins shading. The AD1PCFGL and TRIS registers control the opera- tion of the A/D port pins. Setting a port pin as an analog TABLE 10-1: INPUT VOLTAGE LEVELS(1) input also requires that the corresponding TRIS bit be Tolerated set. If the TRIS bit is cleared (output), the digital output Port or Pin Description Input level (VOH or VOL) will be converted. PORTA<10:9> VDD Only VDD input When reading the PORT register, all pins configured as analog input channels will read as cleared (a low level). PORTB<15:0> levels tolerated. Pins configured as digital inputs will not convert an PORTC<15:12> analog input. Analog levels on any pin that is defined as PORTD<7:6> a digital input (including the ANx pins) may cause the PORTF<0> input buffer to consume current that exceeds the PORTG<9:6> device specifications. PORTA<15:14>, 5.5V Tolerates input 10.2.1 I/O PORT WRITE/READ TIMING PORTA<7:0> levels above One instruction cycle is required between a port PORTC<4:1> VDD, useful for direction change or port write operation and a read PORTD<15:8>, most standard operation of the same port. Typically, this instruction logic. PORTD<5:0> would be a NOP. PORTE<9:0> PORTF<13:12>, PORTF<8:1> PORTG<15:12>, PORTG<3:0> Note 1: Not all port pins shown here are imple- mented on 64-pin and 80-pin devices. Refer to Section1.0 “Device Overview” to confirm which ports are available in specific devices. EXAMPLE 10-1: PORT WRITE/READ EXAMPLE MOV 0xFF00, W0 ; Configure PORTB<15:8> as inputs MOV W0, TRISB ; and PORTB<7:0> as outputs NOP ; Delay 1 cycle BTSS PORTB, #13 ; Next Instruction DS39905E-page 128  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 10.3 Input Change Notification 10.4 Peripheral Pin Select The input change notification function of the I/O ports A major challenge in general purpose devices is provid- allows the PIC24FJ256GA110 family of devices to gen- ing the largest possible set of peripheral features while erate interrupt requests to the processor in response to minimizing the conflict of features on I/O pins. In an a change of state on selected input pins. This feature is application that needs to use more than one peripheral capable of detecting input change of states even in multiplexed on a single pin, inconvenient workarounds Sleep mode, when the clocks are disabled. Depending in application code or a complete redesign may be the on the device pin count, there are up to 81 external only option. inputs that may be selected (enabled) for generating an The Peripheral Pin Select feature provides an alternative interrupt request on a change of state. to these choices by enabling the user’s peripheral set Registers, CNEN1 through CNEN6, contain the selection and their placement on a wide range of I/O interrupt enable control bits for each of the CN input pins. By increasing the pinout options available on a par- pins. Setting any of these bits enables a CN interrupt ticular device, users can better tailor the microcontroller for the corresponding pins. to their entire application, rather than trimming the Each CN pin has both a weak pull-up and a weak application to fit the device. pull-down connected to it. The pull-up acts as a current The Peripheral Pin Select feature operates over a fixed source that is connected to the pin, while the pull-down subset of digital I/O pins. Users may independently acts as a current sink that is connected to the pin. map the input and/or output of any one of many digital These eliminate the need for external resistors when peripherals to any one of these I/O pins. Peripheral Pin push button or keypad devices are connected. The Select is performed in software and generally does not pull-ups and pull-downs are separately enabled using require the device to be reprogrammed. Hardware the CNPU1 through CNPU6 registers (for pull-ups) and safeguards are included that prevent accidental or the CNPD1 through CNPD6 registers (for pull-downs). spurious changes to the peripheral mapping once it has Each CN pin has individual control bits for its pull-up been established. and pull-down. Setting a control bit enables the weak pull-up or pull-down for the corresponding pin. 10.4.1 AVAILABLE PINS When the internal pull-up is selected, the pin pulls up to The Peripheral Pin Select feature is used with a range VDD – 0.7V (typical). Make certain that there is no of up to 46 pins, depending on the particular device and external pull-up source when the internal pull-ups are its pin count. Pins that support the Peripheral Pin enabled, as the voltage difference can cause a current Select feature include the designation “RPn” or “RPIn” path. in their full pin designation, where “n” is the remappable Note: Pull-ups on change notification pins pin number. “RP” is used to designate pins that support should always be disabled whenever the both remappable input and output functions, while port pin is configured as a digital output. “RPI” indicates pins that support remappable input functions only. PIC24FJ256GA110 family devices support a larger number of remappable input only pins than remappable input/output pins. In this device family, there are up to 32 remappable input/output pins, depending on the pin count of the particular device selected; these are num- bered, RP0 through RP31. Remappable input only pins are numbered above this range, from RPI32 to RPI45 (or the upper limit for that particular device). See Table1-4 for a summary of pinout options in each package offering.  2010 Microchip Technology Inc. DS39905E-page 129

PIC24FJ256GA110 FAMILY 10.4.2 AVAILABLE PERIPHERALS 10.4.3.1 Input Mapping The peripherals managed by the Peripheral Pin Select The inputs of the Peripheral Pin Select options are are all digital only peripherals. These include general mapped on the basis of the peripheral; that is, a control serial communications (UART and SPI), general purpose register associated with a peripheral dictates the pin it timer clock inputs, timer related peripherals (input will be mapped to. The RPINRx registers are used to capture and output compare) and external interrupt configure peripheral input mapping (see Register10-1 inputs. Also included are the outputs of the comparator through Register10-21). Each register contains two module, since these are discrete digital signals. sets of 6-bit fields, with each set associated with one of Peripheral Pin Select is not available for I2C™, change the pin-selectable peripherals. Programming a given peripheral’s bit field with an appropriate 6-bit value notification inputs, RTCC alarm outputs or peripherals maps the RPn pin with that value to that peripheral. For with analog inputs. any given device, the valid range of values for any of A key difference between pin select and non pin select the bit fields corresponds to the maximum number of peripherals is that pin select peripherals are not asso- Peripheral Pin Select options supported by the device. ciated with a default I/O pin. The peripheral must always be assigned to a specific I/O pin before it can be 10.4.3.2 Output Mapping used. In contrast, non pin select peripherals are always In contrast to inputs, the outputs of the Peripheral Pin available on a default pin, assuming that the peripheral Select options are mapped on the basis of the pin. In is active and not conflicting with another peripheral. this case, a control register associated with a particular 10.4.2.1 Peripheral Pin Select Function pin dictates the peripheral output to be mapped. The RPORx registers are used to control output mapping. Priority Each register contains two 6-bit fields, with each field Pin-selectable peripheral outputs (e.g. OC, UART being associated with one RPn pin (see Register10-22 Transmit) take priority over general purpose digital through Register10-37). The value of the bit field cor- functions on a pin, such as PMP and port I/O. Special- responds to one of the peripherals and that peripheral’s ized digital outputs, such as USB functionality, will take output is mapped to the pin (see Table10-3). priority over PPS outputs on the same pin. The pin Because of the mapping technique, the list of peripher- diagrams provided at the beginning of this data sheet als for output mapping also includes a null value of list peripheral outputs in order of priority. Refer to them ‘000000’. This permits any given pin to remain for priority concerns on a particular pin. disconnected from the output of any of the pin-selectable Unlike PIC24F devices with fixed peripherals, peripherals. pin-selectable peripheral inputs never take ownership of a pin. The pin’s output buffer is controlled by the 10.4.3.3 Alternate Fixed Pin Mapping TRISx setting or by a fixed peripheral on the pin. If the To provide a migration option from earlier high pin count pin is configured in Digital mode, the PPS input will PIC24F devices, PIC24FJ256GA110 family devices operate correctly. If an analog function is enabled on implement an additional option for mapping the clock the pin, the PPS input will be disabled. output (SCK) of SPI1. This option permits users to map SCK1OUT specifically to the fixed pin function, ASCK1. 10.4.3 CONTROLLING PERIPHERAL PIN The SCK1CM bit (ALTRP<0>) controls this mapping; SELECT setting the bit maps SCK1OUT to ASCK1. Peripheral Pin Select features are controlled through The SCK1CM bit must be set (= 1) before enabling the two sets of Special Function Registers: one to map SPI module. It must remain set while transactions using peripheral inputs and one to map outputs. Because SPI1 are in progress, in order to prevent transmission they are separately controlled, a particular peripheral’s errors; when the module is disabled, the bit must be input and output (if the peripheral has both) can be cleared. Additionally, no other RPOUT register should placed on any selectable function pin without be configured to output the SCK1OUT function while constraint. SCK1CM is set. The association of a peripheral to a peripheral-selectable pin is handled in two different ways, depending on if an input or an output is being mapped. DS39905E-page 130  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 10-2: SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION)(1) Function Mapping Input Name Function Name Register Bits External Interrupt 1 INT1 RPINR0 INT1R<5:0> External Interrupt 2 INT2 RPINR1 INT2R<5:0> External Interrupt 3 INT3 RPINR1 INT3R<5:0> External Interrupt 4 INT4 RPINR2 INT4R<5:0> Input Capture 1 IC1 RPINR7 IC1R<5:0> Input Capture 2 IC2 RPINR7 IC2R<5:0> Input Capture 3 IC3 RPINR8 IC3R<5:0> Input Capture 4 IC4 RPINR8 IC4R<5:0> Input Capture 5 IC5 RPINR9 IC5R<5:0> Input Capture 6 IC6 RPINR9 IC6R<5:0> Input Capture 7 IC7 RPINR10 IC7R<5:0> Input Capture 8 IC8 RPINR10 IC8R<5:0> Input Capture 9 IC9 RPINR15 IC9R<5:0> Output Compare Fault A OCFA RPINR11 OCFAR<5:0> Output Compare Fault B OCFB RPINR11 OCFBR<5:0> SPI1 Clock Input SCK1IN RPINR20 SCK1R<5:0> SPI1 Data Input SDI1 RPINR20 SDI1R<5:0> SPI1 Slave Select Input SS1IN RPINR21 SS1R<5:0> SPI2 Clock Input SCK2IN RPINR22 SCK2R<5:0> SPI2 Data Input SDI2 RPINR22 SDI2R<5:0> SPI2 Slave Select Input SS2IN RPINR23 SS2R<5:0> SPI3 Clock Input SCK3IN RPINR23 SCK3R<5:0> SPI3 Data Input SDI3 RPINR28 SDI3R<5:0> SPI3 Slave Select Input SS3IN RPINR29 SS3R<5:0> Timer2 External Clock T2CK RPINR3 T2CKR<5:0> Timer3 External Clock T3CK RPINR3 T3CKR<5:0> Timer4 External Clock T4CK RPINR4 T4CKR<5:0> Timer5 External Clock T5CK RPINR4 T5CKR<5:0> UART1 Clear To Send U1CTS RPINR18 U1CTSR<5:0> UART1 Receive U1RX RPINR18 U1RXR<5:0> UART2 Clear To Send U2CTS RPINR19 U2CTSR<5:0> UART2 Receive U2RX RPINR19 U2RXR<5:0> UART3 Clear To Send U3CTS RPINR21 U3CTSR<5:0> UART3 Receive U3RX RPINR17 U3RXR<5:0> UART4 Clear To Send U4CTS RPINR27 U4CTSR<5:0> UART4 Receive U4RX RPINR27 U4RXR<5:0> Note 1: Unless otherwise noted, all inputs use the Schmitt Trigger input buffers.  2010 Microchip Technology Inc. DS39905E-page 131

PIC24FJ256GA110 FAMILY TABLE 10-3: SELECTABLE OUTPUT SOURCES (MAPS FUNCTION TO OUTPUT) Output Function Number(1) Function Output Name 0 NULL(2) Null 1 C1OUT Comparator 1 Output 2 C2OUT Comparator 2 Output 3 U1TX UART1 Transmit 4 U1RTS(3) UART1 Request To Send 5 U2TX UART2 Transmit 6 U2RTS(3) UART2 Request To Send 7 SDO1 SPI1 Data Output 8 SCK1OUT(4) SPI1 Clock Output 9 SS1OUT SPI1 Slave Select Output 10 SDO2 SPI2 Data Output 11 SCK2OUT SPI2 Clock Output 12 SS2OUT SPI2 Slave Select Output 18 OC1 Output Compare 1 19 OC2 Output Compare 2 20 OC3 Output Compare 3 21 OC4 Output Compare 4 22 OC5 Output Compare 5 23 OC6 Output Compare 6 24 OC7 Output Compare 7 25 OC8 Output Compare 8 28 U3TX UART3 Transmit 29 U3RTS(3) UART3 Request To Send 30 U4TX UART4 Transmit 31 U4RTS(3) UART4 Request To Send 32 SDO3 SPI3 Data Output 33 SCK3OUT SPI3 Clock Output 34 SS3OUT SPI3 Slave Select Output 35 OC9 Output Compare 9 36 C3OUT Comparator 3 Output 37-63 (unused) NC Note 1: Setting the RPORx register with the listed value assigns that output function to the associated RPn pin. 2: The NULL function is assigned to all RPn outputs at device Reset and disables the RPn output function. 3: IrDA® BCLK functionality uses this output. 4: SCK1OUT can also be specifically mapped to the ASCK1 pin by setting the SCK1CM bit (ALTRP<0>). See Section10.4.3.3 “Alternate Fixed Pin Mapping” for more information. DS39905E-page 132  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 10.4.3.4 Mapping Limitations 10.4.4.1 Control Register Lock The control schema of the Peripheral Pin Select is Under normal operation, writes to the RPINRx and extremely flexible. Other than systematic blocks that RPORx registers are not allowed. Attempted writes will prevent signal contention caused by two physical pins appear to execute normally, but the contents of the being configured as the same functional input or two registers will remain unchanged. To change these reg- functional outputs configured as the same pin, there isters, they must be unlocked in hardware. The register are no hardware enforced lock outs. The flexibility lock is controlled by the IOLOCK bit (OSCCON<6>). extends to the point of allowing a single input to drive Setting IOLOCK prevents writes to the control multiple peripherals or a single functional output to registers; clearing IOLOCK allows writes. drive multiple output pins. To set or clear IOLOCK, a specific command sequence must be executed: 10.4.3.5 Mapping Exceptions for PIC24FJ256GA110 Family Devices 1. Write 46h to OSCCON<7:0>. 2. Write 57h to OSCCON<7:0>. Although the PPS registers theoretically allow for up to 64 remappable I/O pins, not all of these are implemented 3. Clear (or set) IOLOCK as a single operation. in all devices. For PIC24FJ256GA110 family devices, Unlike the similar sequence with the oscillator’s LOCK the maximum number of remappable pins available are bit, IOLOCK remains in one state until changed. This 46, which includes 14 input only pins. In addition, some allows all of the Peripheral Pin Selects to be configured pins in the RPn and RPIn sequences are unimple- with a single unlock sequence, followed by an update mented in lower pin count devices. The differences in to all control registers, then locked with a second lock available remappable pins are summarized in sequence. Table10-4. 10.4.4.2 Continuous State Monitoring When developing applications that use remappable pins, users should also keep these things in mind: In addition to being protected from direct writes, the contents of the RPINRx and RPORx registers are • For the RPINRx registers, bit combinations constantly monitored in hardware by shadow registers. corresponding to an unimplemented pin for a If an unexpected change in any of the registers occurs particular device are treated as invalid; the (such as cell disturbances caused by ESD or other corresponding module will not have an input external events), a Configuration Mismatch Reset will mapped to it. For all PIC24FJ256GA110 family be triggered. devices, this includes all values greater than 45 (‘101101’). 10.4.4.3 Configuration Bit Pin Select Lock • For RPORx registers, the bit fields corresponding As an additional level of safety, the device can be con- to an unimplemented pin will also be figured to prevent more than one write session to the unimplemented. Writing to these fields will have RPINRx and RPORx registers. The IOL1WAY no effect. (CW2<4>) Configuration bit blocks the IOLOCK bit 10.4.4 CONTROLLING CONFIGURATION from being cleared after it has been set once. If CHANGES IOLOCK remains set, the register unlock procedure will not execute and the Peripheral Pin Select Control Because peripheral remapping can be changed during registers cannot be written to. The only way to clear the run time, some restrictions on peripheral remapping bit and re-enable peripheral remapping is to perform a are needed to prevent accidental configuration device Reset. changes. PIC24F devices include three features to prevent alterations to the peripheral map: In the default (unprogrammed) state, IOL1WAY is set, restricting users to one write session. Programming • Control register lock sequence IOL1WAY allows users unlimited access (with the • Continuous state monitoring proper use of the unlock sequence) to the Peripheral • Configuration bit remapping lock Pin Select registers. TABLE 10-4: REMAPPABLE PIN EXCEPTIONS FOR PIC24FJ256GA110 FAMILY DEVICES RP Pins (I/O) RPI Pins Device Pin Count Total Unimplemented Total Unimplemented 64-pin 29 RP5, RP15, RP31 2 RPI32-36, RPI38-44 80-pin 31 RP31 11 RPI32, RPI39, RPI41 100-pin 32 — 14 —  2010 Microchip Technology Inc. DS39905E-page 133

PIC24FJ256GA110 FAMILY 10.4.5 CONSIDERATIONS FOR Along these lines, configuring a remappable pin for a PERIPHERAL PIN SELECTION specific peripheral does not automatically turn that feature on. The peripheral must be specifically config- The ability to control Peripheral Pin Select options ured for operation and enabled, as if it were tied to a fixed introduces several considerations into application pin. Where this happens in the application code (immedi- design that could be overlooked. This is particularly ately following device Reset and peripheral configuration true for several common peripherals that are available or inside the main application routine) depends on the only as remappable peripherals. peripheral and its use in the application. The main consideration is that the Peripheral Pin A final consideration is that Peripheral Pin Select func- Selects are not available on default pins in the device’s tions neither override analog inputs, nor reconfigure default (Reset) state. Since all RPINRx registers reset pins with analog functions for digital I/O. If a pin is to ‘111111’ and all RPORx registers reset to ‘000000’, configured as an analog input on device Reset, it must all Peripheral Pin Select inputs are tied to VSS and all be explicitly reconfigured as digital I/O when used with Peripheral Pin Select outputs are disconnected. a Peripheral Pin Select. Note: In tying Peripheral Pin Select inputs to Example10-2 shows a configuration for bidirectional RP63, RP63 does not have to exist on a communication with flow control using UART1. The device for the registers to be reset to it. following input and output functions are used: This situation requires the user to initialize the device • Input Functions: U1RX, U1CTS with the proper peripheral configuration before any • Output Functions: U1TX, U1RTS other application code is executed. Since the IOLOCK bit resets in the unlocked state, it is not necessary to EXAMPLE 10-2: CONFIGURING UART1 execute the unlock sequence after the device has INPUT AND OUTPUT come out of Reset. For application safety, however, it is FUNCTIONS best to set IOLOCK and lock the configuration after writing to the control registers. // Unlock Registers __builtin_write_OSCCONL(OSCCON & 0xBF); Because the unlock sequence is timing critical, it must be executed as an assembly language routine in the // Configure Input Functions (Table 9-1)) same manner as changes to the oscillator configura- // Assign U1RX To Pin RP0 tion. If the bulk of the application is written in C or RPINR18bits.U1RXR = 0; another high-level language, the unlock sequence should be performed by writing in-line assembly. // Assign U1CTS To Pin RP1 RPINR18bits.U1CTSR = 1; Choosing the configuration requires the review of all Peripheral Pin Selects and their pin assignments, // Configure Output Functions (Table 9-2) especially those that will not be used in the application. // Assign U1TX To Pin RP2 In all cases, unused pin-selectable peripherals should RPOR1bits.RP2R = 3; be disabled completely. Unused peripherals should have their inputs assigned to an unused RPn pin // Assign U1RTS To Pin RP3 function. I/O pins with unused RPn functions should be RPOR1bits.RP3R = 4; configured with the null peripheral output. // Lock Registers The assignment of a peripheral to a particular pin does __builtin_write_OSCCONL(OSCCON | 0x40); not automatically perform any other configuration of the pin’s I/O circuitry. In theory, this means adding a pin-selectable output to a pin may mean inadvertently driving an existing peripheral input when the output is driven. Users must be familiar with the behavior of other fixed peripherals that share a remappable pin and know when to enable or disable them. To be safe, fixed digital peripherals that share the same pin should be disabled when not in use. DS39905E-page 134  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 10.4.6 PERIPHERAL PIN SELECT Note: Input and output register values can only REGISTERS be changed if IOLOCK (OSCCON<6>) = 0. The PIC24FJ256GA110 family of devices implements See Section10.4.4.1 “Control Register a total of 37 registers for remappable peripheral Lock” for a specific command sequence. configuration: • Input Remappable Peripheral Registers (21) • Output Remappable Peripheral Registers (16) REGISTER 10-1: RPINR0: PERIPHERAL PIN SELECT INPUT REGISTER 0 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — INT1R5 INT1R4 INT1R3 INT1R2 INT1R1 INT1R0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 INT1R<5:0>: Assign External Interrupt 1 (INT1) to Corresponding RPn or RPIn Pin bits bit 7-0 Unimplemented: Read as ‘0’ REGISTER 10-2: RPINR1: PERIPHERAL PIN SELECT INPUT REGISTER 1 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — INT3R5 INT3R4 INT3R3 INT3R2 INT3R1 INT3R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — INT2R5 INT2R4 INT2R3 INT2R2 INT2R1 INT2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 INT3R<5:0>: Assign External Interrupt 3 (INT3) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 INT2R<5:0>: Assign External Interrupt 2 (INT2) to Corresponding RPn or RPIn Pin bits  2010 Microchip Technology Inc. DS39905E-page 135

PIC24FJ256GA110 FAMILY REGISTER 10-3: RPINR2: PERIPHERAL PIN SELECT INPUT REGISTER 2 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — INT4R5 INT4R4 INT4R3 INT4R2 INT4R1 INT4R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5-0 INT4R<5:0>: Assign External Interrupt 4 (INT4) to Corresponding RPn or RPIn Pin bits REGISTER 10-4: RPINR3: PERIPHERAL PIN SELECT INPUT REGISTER 3 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — T3CKR5 T3CKR4 T3CKR3 T3CKR2 T3CKR1 T3CKR0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — T2CKR5 T2CKR4 T2CKR3 T2CKR2 T2CKR1 T2CKR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 T3CKR<5:0>: Assign Timer3 External Clock (T3CK) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 T2CKR<5:0>: Assign Timer2 External Clock (T2CK) to Corresponding RPn or RPIn Pin bits DS39905E-page 136  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-5: RPINR4: PERIPHERAL PIN SELECT INPUT REGISTER 4 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — T5CKR5 T5CKR4 T5CKR3 T5CKR2 T5CKR1 T5CKR0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — T4CKR5 T4CKR4 T4CKR3 T4CKR2 T4CKR1 T4CKR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 T5CKR<5:0>: Assign Timer5 External Clock (T5CK) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 T4CKR<5:0>: Assign Timer4 External Clock (T4CK) to Corresponding RPn or RPIn Pin bits REGISTER 10-6: RPINR7: PERIPHERAL PIN SELECT INPUT REGISTER 7 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC2R5 IC2R4 IC2R3 IC2R2 IC2R1 IC2R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC1R5 IC1R4 IC1R3 IC1R2 IC1R1 IC1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 IC2R<5:0>: Assign Input Capture 2 (IC2) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 IC1R<5:0>: Assign Input Capture 1 (IC1) to Corresponding RPn or RPIn Pin bits  2010 Microchip Technology Inc. DS39905E-page 137

PIC24FJ256GA110 FAMILY REGISTER 10-7: RPINR8: PERIPHERAL PIN SELECT INPUT REGISTER 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC4R5 IC4R4 IC4R3 IC4R2 IC4R1 IC4R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC3R5 IC3R4 IC3R3 IC3R2 IC3R1 IC3R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 IC4R<5:0>: Assign Input Capture 4 (IC4) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 IC3R<5:0>: Assign Input Capture 3 (IC3) to Corresponding RPn or RPIn Pin bits REGISTER 10-8: RPINR9: PERIPHERAL PIN SELECT INPUT REGISTER 9 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC6R5 IC6R4 IC6R3 IC6R2 IC6R1 IC6R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC5R5 IC5R4 IC5R3 IC5R2 IC5R1 IC5R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 IC6R<5:0>: Assign Input Capture 6 (IC6) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 IC5R<5:0>: Assign Input Capture 5 (IC5) to Corresponding RPn or RPIn Pin bits DS39905E-page 138  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-9: RPINR10: PERIPHERAL PIN SELECT INPUT REGISTER 10 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC8R5 IC8R4 IC8R3 IC8R2 IC8R1 IC8R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC7R5 IC7R4 IC7R3 IC7R2 IC7R1 IC7R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 IC8R<5:0>: Assign Input Capture 8 (IC8) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 IC7R<5:0>: Assign Input Capture 7 (IC7) to Corresponding RPn or RPIn Pin bits REGISTER 10-10: RPINR11: PERIPHERAL PIN SELECT INPUT REGISTER 11 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — OCFBR5 OCFBR4 OCFBR3 OCFBR2 OCFBR1 OCFBR0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — OCFAR5 OCFAR4 OCFAR3 OCFAR2 OCFAR1 OCFAR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 OCFBR<5:0>: Assign Output Compare Fault B (OCFB) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 OCFAR<5:0>: Assign Output Compare Fault A (OCFA) to Corresponding RPn or RPIn Pin bits  2010 Microchip Technology Inc. DS39905E-page 139

PIC24FJ256GA110 FAMILY REGISTER 10-11: RPINR15: PERIPHERAL PIN SELECT INPUT REGISTER 15 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — IC9R5 IC9R4 IC9R3 IC9R2 IC9R1 IC9R0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 IC9R<5:0>: Assign Input Capture 9 (IC9) to Corresponding RPn or RPIn Pin bits bit 7-0 Unimplemented: Read as ‘0’ REGISTER 10-12: RPINR17: PERIPHERAL PIN SELECT INPUT REGISTER 17 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U3RXR5 U3RXR4 U3RXR3 U3RXR2 U3RXR1 U3RXR0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 U3RXR<5:0>: Assign UART3 Receive (U3RX) to Corresponding RPn or RPIn Pin bits bit 7-0 Unimplemented: Read as ‘0’ DS39905E-page 140  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-13: RPINR18: PERIPHERAL PIN SELECT INPUT REGISTER 18 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U1CTSR5 U1CTSR4 U1CTSR3 U1CTSR2 U1CTSR1 U1CTSR0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U1RXR5 U1RXR4 U1RXR3 U1RXR2 U1RXR1 U1RXR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 U1CTSR<5:0:> Assign UART1 Clear to Send (U1CTS) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 U1RXR<5:0>: Assign UART1 Receive (U1RX) to Corresponding RPn or RPIn Pin bits REGISTER 10-14: RPINR19: PERIPHERAL PIN SELECT INPUT REGISTER 19 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U2CTSR5 U2CTSR4 U2CTSR3 U2CTSR2 U2CTSR1 U2CTSR0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U2RXR5 U2RXR4 U2RXR3 U2RXR2 U2RXR1 U2RXR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 U2CTSR<5:0>: Assign UART2 Clear to Send (U2CTS) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 U2RXR<5:0>: Assign UART2 Receive (U2RX) to Corresponding RPn or RPIn Pin bits  2010 Microchip Technology Inc. DS39905E-page 141

PIC24FJ256GA110 FAMILY REGISTER 10-15: RPINR20: PERIPHERAL PIN SELECT INPUT REGISTER 20 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SCK1R5 SCK1R4 SCK1R3 SCK1R2 SCK1R1 SCK1R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SDI1R5 SDI1R4 SDI1R3 SDI1R2 SDI1R1 SDI1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 SCK1R<5:0>: Assign SPI1 Clock Input (SCK1IN) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 SDI1R<5:0>: Assign SPI1 Data Input (SDI1) to Corresponding RPn or RPIn Pin bits REGISTER 10-16: RPINR21: PERIPHERAL PIN SELECT INPUT REGISTER 21 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U3CTSR5 U3CTSR4 U3CTSR3 U3CTSR2 U3CTSR1 U3CTSR0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SS1R5 SS1R4 SS1R3 SS1R2 SS1R1 SS1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 U3CTSR<5:0>: Assign UART3 Clear to Send (U3CTS) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 SS1R<5:0>: Assign SPI1 Slave Select Input (SS1IN) to Corresponding RPn or RPIn Pin bits DS39905E-page 142  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-17: RPINR22: PERIPHERAL PIN SELECT INPUT REGISTER 22 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SCK2R5 SCK2R4 SCK2R3 SCK2R2 SCK2R1 SCK2R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SDI2R5 SDI2R4 SDI2R3 SDI2R2 SDI2R1 SDI2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 SCK2R<5:0>: Assign SPI2 Clock Input (SCK2IN) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 SDI2R<5:0>: Assign SPI2 Data Input (SDI2) to Corresponding RPn or RPIn Pin bits REGISTER 10-18: RPINR23: PERIPHERAL PIN SELECT INPUT REGISTER 23 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SS2R5 SS2R4 SS2R3 SS2R2 SS2R1 SS2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5-0 SS2R<5:0>: Assign SPI2 Slave Select Input (SS2IN) to Corresponding RPn or RPIn Pin bits  2010 Microchip Technology Inc. DS39905E-page 143

PIC24FJ256GA110 FAMILY REGISTER 10-19: RPINR27: PERIPHERAL PIN SELECT INPUT REGISTER 27 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U4CTSR5 U4CTSR4 U4CTSR3 U4CTSR2 U4CTSR1 U4CTSR0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — U4RXR5 U4RXR4 U4RXR3 U4RXR2 U4RXR1 U4RXR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 U4CTSR<5:0>: Assign UART4 Clear to Send (U4CTS) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 U4RXR<5:0>: Assign UART4 Receive (U4RX) to Corresponding RPn or RPIn Pin bits REGISTER 10-20: RPINR28: PERIPHERAL PIN SELECT INPUT REGISTER 28 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SCK3R5 SCK3R4 SCK3R3 SCK3R2 SCK3R1 SCK3R0 bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SDI3R5 SDI3R4 SDI3R3 SDI3R2 SDI3R1 SDI3R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 SCK3R<5:0>: Assign SPI3 Data Input (SCK3IN) to Corresponding RPn or RPIn Pin bits bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 SDI3R<5:0>: Assign SPI3 Data Input (SDI3) to Corresponding RPn or RPIn Pin bits DS39905E-page 144  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-21: RPINR29: PERIPHERAL PIN SELECT INPUT REGISTER 29 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — SS3R5 SS3R4 SS3R3 SS3R2 SS3R1 SS3R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5-0 SS3R<5:0>: Assign SPI3 Slave Select Input (SS31IN) to Corresponding RPn or RPIn Pin bits  2010 Microchip Technology Inc. DS39905E-page 145

PIC24FJ256GA110 FAMILY REGISTER 10-22: RPOR0: PERIPHERAL PIN SELECT OUTPUT REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP1R5 RP1R4 RP1R3 RP1R2 RP1R1 RP1R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP0R5 RP0R4 RP0R3 RP0R2 RP0R1 RP0R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP1R<5:0>: RP1 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP1 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP0R<5:0>: RP0 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP0 (see Table10-3 for peripheral function numbers). REGISTER 10-23: RPOR1: PERIPHERAL PIN SELECT OUTPUT REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP3R5 RP3R4 RP3R3 RP3R2 RP3R1 RP3R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP2R5 RP2R4 RP2R3 RP2R2 RP2R1 RP2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP3R<5:0>: RP3 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP3 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP2R<5:0>: RP2 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP2 (see Table10-3 for peripheral function numbers). DS39905E-page 146  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-24: RPOR2: PERIPHERAL PIN SELECT OUTPUT REGISTER 2 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP5R5(1) RP5R4(1) RP5R3(1) RP5R2(1) RP5R1(1) RP5R0(1) bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP4R5 RP4R4 RP4R3 RP4R2 RP4R1 RP4R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP5R<5:0>: RP5 Output Pin Mapping bits(1) Peripheral output number n is assigned to pin, RP5 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP4R<5:0>: RP4 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP4 (see Table10-3 for peripheral function numbers). Note 1: Unimplemented in 64-pin devices; read as ‘0’. REGISTER 10-25: RPOR3: PERIPHERAL PIN SELECT OUTPUT REGISTER 3 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP7R5 RP7R4 RP7R3 RP7R2 RP7R1 RP7R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP6R5 RP6R4 RP6R3 RP6R2 RP6R1 RP6R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP7R<5:0>: RP7 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP7 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP6R<5:0>: RP6 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP6 (see Table10-3 for peripheral function numbers).  2010 Microchip Technology Inc. DS39905E-page 147

PIC24FJ256GA110 FAMILY REGISTER 10-26: RPOR4: PERIPHERAL PIN SELECT OUTPUT REGISTER 4 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP9R5 RP9R4 RP9R3 RP9R2 RP9R1 RP9R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP8R5 RP8R4 RP8R3 RP8R2 RP8R1 RP8R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP9R<5:0>: RP9 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP9 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP8R<5:0>: RP8 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP8 (see Table10-3 for peripheral function numbers). REGISTER 10-27: RPOR5: PERIPHERAL PIN SELECT OUTPUT REGISTER 5 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP11R5 RP11R4 RP11R3 RP11R2 RP11R1 RP11R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP10R5 RP10R4 RP10R3 RP10R2 RP10R1 RP10R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP11R<5:0>: RP11 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP11 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP10R<5:0>: RP10 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP10 (see Table10-3 for peripheral function numbers). DS39905E-page 148  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-28: RPOR6: PERIPHERAL PIN SELECT OUTPUT REGISTER 6 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP13R5 RP13R4 RP13R3 RP13R2 RP13R1 RP13R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP12R5 RP12R4 RP12R3 RP12R2 RP12R1 RP12R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP13R<5:0>: RP13 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP13 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP12R<5:0>: RP12 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP12 (see Table10-3 for peripheral function numbers). REGISTER 10-29: RPOR7: PERIPHERAL PIN SELECT OUTPUT REGISTER 7 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP15R5(1) RP15R4(1) RP15R3(1) RP15R2(1) RP15R1(1) RP15R0(1) bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP14R5 RP14R4 RP14R3 RP14R2 RP14R1 RP14R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP15R<5:0>: RP15 Output Pin Mapping bits(1) Peripheral output number n is assigned to pin, RP15 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP14R<5:0>: RP14 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP14 (see Table10-3 for peripheral function numbers). Note 1: Unimplemented in 64-pin devices; read as ‘0’.  2010 Microchip Technology Inc. DS39905E-page 149

PIC24FJ256GA110 FAMILY REGISTER 10-30: RPOR8: PERIPHERAL PIN SELECT OUTPUT REGISTER 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP17R5 RP17R4 RP17R3 RP17R2 RP17R1 RP17R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP16R5 RP16R4 RP16R3 RP16R2 RP16R1 RP16R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP17R<5:0>: RP17 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP17 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP16R<5:0>: RP16 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP16 (see Table10-3 for peripheral function numbers). REGISTER 10-31: RPOR9: PERIPHERAL PIN SELECT OUTPUT REGISTER 9 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP19R5 RP19R4 RP19R3 RP19R2 RP19R1 RP19R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP18R5 RP18R4 RP18R3 RP18R2 RP18R1 RP18R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP19R<5:0>: RP19 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP19 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP18R<5:0>: RP18 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP18 (see Table10-3 for peripheral function numbers). DS39905E-page 150  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-32: RPOR10: PERIPHERAL PIN SELECT OUTPUT REGISTER 10 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP21R5 RP21R4 RP21R3 RP21R2 RP21R1 RP21R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP20R5 RP20R4 RP20R3 RP20R2 RP20R1 RP20R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP21R<5:0>: RP21 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP21 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP20R<5:0:> RP20 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP20 (see Table10-3 for peripheral function numbers). REGISTER 10-33: RPOR11: PERIPHERAL PIN SELECT OUTPUT REGISTER 11 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP23R5 RP23R4 RP23R3 RP23R2 RP23R1 RP23R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP22R5 RP22R4 RP22R3 RP22R2 RP22R1 RP22R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP23R<5:0>: RP23 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP23 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP22R<5:0>: RP22 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP22 (see Table10-3 for peripheral function numbers).  2010 Microchip Technology Inc. DS39905E-page 151

PIC24FJ256GA110 FAMILY REGISTER 10-34: RPOR12: PERIPHERAL PIN SELECT OUTPUT REGISTER 12 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP25R5 RP25R4 RP25R3 RP25R2 RP25R1 RP25R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP24R5 RP24R4 RP24R3 RP24R2 RP24R1 RP24R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP25R<5:0>: RP25 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP25 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP24R<5:0>: RP24 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP24 (see Table10-3 for peripheral function numbers). REGISTER 10-35: RPOR13: PERIPHERAL PIN SELECT OUTPUT REGISTER 13 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP27R5 RP27R4 RP27R3 RP27R2 RP27R1 RP27R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP26R5 RP26R4 RP26R3 RP26R2 RP26R1 RP26R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP27R<5:0>: RP27 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP27 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP26R<5:0>: RP26 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP26 (see Table10-3 for peripheral function numbers). DS39905E-page 152  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 10-36: RPOR14: PERIPHERAL PIN SELECT OUTPUT REGISTER 14 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP29R5 RP29R4 RP29R3 RP29R2 RP29R1 RP29R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP28R5 RP28R4 RP28R3 RP28R2 RP28R1 RP28R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP29R<5:0>: RP29 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP29 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP28R<5:0>: RP28 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP28 (see Table10-3 for peripheral function numbers). REGISTER 10-37: RPOR15: PERIPHERAL PIN SELECT OUTPUT REGISTER 15 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP31R5(1) RP31R4(1) RP31R3(1) RP31R2(1) RP31R1(1) RP31R0(1) bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP30R5 RP30R4 RP30R3 RP30R2 RP30R1 RP30R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP31R<5:0>: RP31 Output Pin Mapping bits(1) Peripheral output number n is assigned to pin, RP31 (see Table10-3 for peripheral function numbers). bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP30R<5:0>: RP30 Output Pin Mapping bits Peripheral output number n is assigned to pin, RP30 (see Table10-3 for peripheral function numbers). Note 1: Unimplemented in 64-pin and 80-pin devices; read as ‘0’.  2010 Microchip Technology Inc. DS39905E-page 153

PIC24FJ256GA110 FAMILY REGISTER 10-38: ALTRP: ALTERNATE PERIPHERAL PIN MAPPING REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — SCK1CM bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-1 Unimplemented: Read as ‘0’ bit 0 SCK1CM: SCK1 Output Mapping Select bit 1 = SCK1 output function is mapped to ASCK1 pin only 0 = SCK1 output function is mapped according to RPORn registers DS39905E-page 154  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 11.0 TIMER1 Figure11-1 presents a block diagram of the 16-bit timer module. Note: This data sheet summarizes the features of To configure Timer1 for operation: this group of PIC24F devices. It is not intended to be a comprehensive reference 1. Set the TON bit (= 1). source. For more information, refer to the 2. Select the timer prescaler ratio using the “PIC24F Family Reference Manual”, TCKPS<1:0> bits. Section 14. “Timers” (DS39704). 3. Set the Clock and Gating modes using the TCS and TGATE bits. The Timer1 module is a 16-bit timer which can serve as 4. Set or clear the TSYNC bit to configure the time counter for the Real-Time Clock (RTC), or synchronous or asynchronous operation. operate as a free-running, interval timer/counter. Timer1 can operate in three modes: 5. Load the timer period value into the PR1 register. • 16-Bit Timer 6. If interrupts are required, set the interrupt enable • 16-Bit Synchronous Counter bit, T1IE. Use the priority bits, T1IP<2:0>, to set • 16-Bit Asynchronous Counter the interrupt priority. Timer1 also supports these features: • Timer Gate Operation • Selectable Prescaler Settings • Timer Operation during CPU Idle and Sleep modes • Interrupt on 16-Bit Period Register Match or Falling Edge of External Gate Signal FIGURE 11-1: 16-BIT TIMER1 MODULE BLOCK DIAGRAM TCKPS<1:0> TON 2 SOSCO/ 1x T1CK Gate Prescaler SOSCEN Sync 01 1, 8, 64, 256 SOSCI TCY 00 TGATE TGATE TCS 1 Q D Set T1IF 0 Q CK 0 Reset TMR1 1 Sync Comparator TSYNC Equal PR1  2010 Microchip Technology Inc. DS39905E-page 155

PIC24FJ256GA110 FAMILY REGISTER 11-1: T1CON: TIMER1 CONTROL REGISTER(1) R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 TON — TSIDL — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 U-0 — TGATE TCKPS1 TCKPS0 — TSYNC TCS — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TON: Timer1 On bit 1 = Starts 16-bit Timer1 0 = Stops 16-bit Timer1 bit 14 Unimplemented: Read as ‘0’ bit 13 TSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-7 Unimplemented: Read as ‘0’ bit 6 TGATE: Timer1 Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation enabled 0 = Gated time accumulation disabled bit 5-4 TCKPS<1:0>: Timer1 Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3 Unimplemented: Read as ‘0’ bit 2 TSYNC: Timer1 External Clock Input Synchronization Select bit When TCS = 1: 1 = Synchronize external clock input 0 = Do not synchronize external clock input When TCS = 0: This bit is ignored. bit 1 TCS: Timer1 Clock Source Select bit 1 = External clock from T1CK pin (on the rising edge) 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as ‘0’ Note 1: Changing the value of TxCON while the timer is running (TON = 1) causes the timer prescale counter to reset and is not recommended. DS39905E-page 156  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 12.0 TIMER2/3 AND TIMER4/5 To configure Timer2/3 or Timer4/5 for 32-bit operation: 1. Set the T32 bit (T2CON<3> or T4CON<3> = 1). Note: This data sheet summarizes the features of 2. Select the prescaler ratio for Timer2 or Timer4 this group of PIC24F devices. It is not using the TCKPS<1:0> bits. intended to be a comprehensive reference 3. Set the Clock and Gating modes using the TCS source. For more information, refer to the and TGATE bits. If TCS is set to external clock, “PIC24F Family Reference Manual”, RPINRx (TxCK) must be configured to an avail- Section 14. “Timers” (DS39704). able RPn pin. See Section 10.4“Peripheral The Timer2/3 and Timer4/5 modules are 32-bit timers, Pin Select” for more information. which can also be configured as four independent 16-bit 4. Load the timer period value. PR3 (or PR5) will timers with selectable operating modes. contain the most significant word of the value As 32-bit timers, Timer2/3 and Timer4/5 can each while PR2 (or PR4) contains the least significant operate in three modes: word. 5. If interrupts are required, set the interrupt enable • Two independent 16-bit timers with all 16-bit bit, T3IE or T5IE; use the priority bits, T3IP<2:0> operating modes (except Asynchronous Counter or T5IP<2:0>, to set the interrupt priority. Note mode) that while Timer2 or Timer4 controls the timer, • Single 32-bit timer the interrupt appears as a Timer3 or Timer5 • Single 32-bit synchronous counter interrupt. They also support these features: 6. Set the TON bit (= 1). • Timer Gate Operation The timer value, at any point, is stored in the register • Selectable Prescaler Settings pair: TMR3:TMR2 (or TMR5:TMR4). TMR3 (TMR5) • Timer Operation during Idle and Sleep modes always contains the most significant word of the count, while TMR2 (TMR4) contains the least significant word. • Interrupt on a 32-Bit Period Register Match • ADC Event Trigger (Timer2/3 only) To configure any of the timers for individual 16-bit operation: Individually, all four of the 16-bit timers can function as synchronous timers or counters. They also offer the 1. Clear the T32 bit corresponding to that timer features listed above, except for the ADC event trigger; (T2CON<3> for Timer2 and Timer3 or this is implemented only with Timer3. The operating T4CON<3> for Timer4 and Timer5). modes and enabled features are determined by setting 2. Select the timer prescaler ratio using the the appropriate bit(s) in the T2CON, T3CON, T4CON TCKPS<1:0> bits. and T5CON registers. T2CON and T4CON are shown 3. Set the Clock and Gating modes using the TCS in generic form in Register12-1; T3CON and T5CON and TGATE bits. See Section 10.4“Peripheral are shown in Register12-2. Pin Select” for more information. For 32-bit timer/counter operation, Timer2 and Timer4 4. Load the timer period value into the PRx register. are the least significant word; Timer3 and Timer4 are 5. If interrupts are required, set the interrupt enable the most significant word of the 32-bit timers. bit, TxIE; use the priority bits, TxIP<2:0>, to set the interrupt priority. Note: For 32-bit operation, T3CON and T5CON control bits are ignored. Only T2CON and 6. Set the TON bit (TxCON<15> = 1). T4CON control bits are used for setup and control. Timer2 and Timer4 clock and gate inputs are utilized for the 32-bit timer modules, but an interrupt is generated with the Timer3 or Timer5 interrupt flags.  2010 Microchip Technology Inc. DS39905E-page 157

PIC24FJ256GA110 FAMILY FIGURE 12-1: TIMER2/3 AND TIMER4/5 (32-BIT) BLOCK DIAGRAM TCKPS<1:0> TON 2 T2CK 1x (T4CK) Gate Prescaler Sync 01 1, 8, 64, 256 TCY 00 TGATE TGATE(2) TCS(2) 1 Q D Set T3IF (T5IF) Q CK 0 PR3 PR2 (PR5) (PR4) ADC Event Trigger(3) Equal Comparator MSB LSB TMR3 TMR2 Sync Reset (TMR5) (TMR4) 16 Read TMR2 (TMR4)(1) Write TMR2 (TMR4)(1) 16 TMR3HLD 16 (TMR5HLD) Data Bus<15:0> Note 1: The 32-Bit Timer Configuration bit, T32, must be set for 32-bit timer/counter operation. All control bits are respective to the T2CON and T4CON registers. 2: The Timer clock input must be assigned to an available RPn pin before use. Please see Section 10.4“Peripheral Pin Select” for more information. 3: The ADC event trigger is available only on Timer2/3 in 32-bit mode and Timer3 in 16-bit mode. DS39905E-page 158  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 12-2: TIMER2 AND TIMER4 (16-BIT SYNCHRONOUS) BLOCK DIAGRAM TCKPS<1:0> TON 2 T2CK 1x (T4CK) Gate Prescaler Sync 01 1, 8, 64, 256 TGATE 00 TCY TCS(1) 1 Q D TGATE(1) Set T2IF (T4IF) Q CK 0 Reset TMR2 (TMR4) Sync Comparator Equal PR2 (PR4) Note 1: The Timer clock input must be assigned to an available RPn pin before use. Please see Section 10.4“Peripheral Pin Select” for more information. FIGURE 12-3: TIMER3 AND TIMER5 (16-BIT ASYNCHRONOUS) BLOCK DIAGRAM TCKPS<1:0> T3CK TON 2 Sync 1x (T5CK) Prescaler 01 1, 8, 64, 256 TGATE 00 TCY TCS(1) 1 Q D TGATE(1) Set T3IF (T5IF) Q CK 0 Reset TMR3 (TMR5) ADC Event Trigger(2) Comparator Equal PR3 (PR5) Note 1: The Timer clock input must be assigned to an available RPn pin before use. Please see Section 10.4“Peripheral Pin Select” for more information. 2: The ADC event trigger is available only on Timer3.  2010 Microchip Technology Inc. DS39905E-page 159

PIC24FJ256GA110 FAMILY REGISTER 12-1: TxCON: TIMER2 AND TIMER4 CONTROL REGISTER(3) R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 TON — TSIDL — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 U-0 — TGATE TCKPS1 TCKPS0 T32(1) — TCS(2) — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TON: Timerx On bit When TxCON<3> = 1: 1 = Starts 32-bit Timerx/y 0 = Stops 32-bit Timerx/y When TxCON<3> = 0: 1 = Starts 16-bit Timerx 0 = Stops 16-bit Timerx bit 14 Unimplemented: Read as ‘0’ bit 13 TSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-7 Unimplemented: Read as ‘0’ bit 6 TGATE: Timerx Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation enabled 0 = Gated time accumulation disabled bit 5-4 TCKPS<1:0>: Timerx Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3 T32: 32-Bit Timer Mode Select bit(1) 1 = Timerx and Timery form a single 32-bit timer 0 = Timerx and Timery act as two 16-bit timers In 32-bit mode, T3CON control bits do not affect 32-bit timer operation. bit 2 Unimplemented: Read as ‘0’ bit 1 TCS: Timerx Clock Source Select bit(2) 1 = External clock from pin, TxCK (on the rising edge) 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as ‘0’ Note 1: In 32-bit mode, the T3CON or T5CON control bits do not affect 32-bit timer operation. 2: If TCS = 1, RPINRx (TxCK) must be configured to an available RPn pin. For more information, see Section 10.4“Peripheral Pin Select”. 3: Changing the value of TxCON while the timer is running (TON = 1) causes the timer prescale counter to reset and is not recommended. DS39905E-page 160  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 12-2: TyCON: TIMER3 AND TIMER5 CONTROL REGISTER(3) R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 TON(1) — TSIDL(1) — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 U-0 — TGATE(1) TCKPS1(1) TCKPS0(1) — — TCS(1,2) — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TON: Timery On bit(1) 1 = Starts 16-bit Timery 0 = Stops 16-bit Timery bit 14 Unimplemented: Read as ‘0’ bit 13 TSIDL: Stop in Idle Mode bit(1) 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-7 Unimplemented: Read as ‘0’ bit 6 TGATE: Timery Gated Time Accumulation Enable bit(1) When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation enabled 0 = Gated time accumulation disabled bit 5-4 TCKPS<1:0>: Timery Input Clock Prescale Select bits(1) 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3-2 Unimplemented: Read as ‘0’ bit 1 TCS: Timery Clock Source Select bit(1,2) 1 = External clock from pin TyCK (on the rising edge) 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as ‘0’ Note 1: When 32-bit operation is enabled (T2CON<3> or T4CON<3> = 1), these bits have no effect on Timery operation; all timer functions are set through T2CON and T4CON. 2: If TCS = 1, RPINRx (TyCK) must be configured to an available RPn pin. See Section 10.4“Peripheral Pin Select” for more information. 3: Changing the value of TyCON while the timer is running (TON = 1) causes the timer prescale counter to reset and is not recommended.  2010 Microchip Technology Inc. DS39905E-page 161

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 162  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 13.0 INPUT CAPTURE WITH 13.1 General Operating Modes DEDICATED TIMER 13.1.1 SYNCHRONOUS AND TRIGGER Note: This data sheet summarizes the features of MODES this group of PIC24F devices. It is not By default, the enhanced input capture module oper- intended to be a comprehensive reference ates in a free-running mode. The internal 16-bit counter source. For more information, refer to the ICxTMR counts up continuously, wrapping around from “PIC24F Family Reference Manual”, FFFFh to 0000h on each overflow, with its period Section 34. “Input Capture with synchronized to the selected external clock source. Dedicated Timer” (DS39722) When a capture event occurs, the current 16-bit value of the internal counter is written to the FIFO buffer. Devices in the PIC24FJ256GA110 family all feature 9independent enhanced input capture modules. Each In Synchronous mode, the module begins capturing of the modules offers a wide range of configuration and events on the ICx pin as soon as its selected clock operating options for capturing external pulse events source is enabled. Whenever an event occurs on the and generating interrupts. selected sync source, the internal counter is reset. In Trigger mode, the module waits for a Sync event from Key features of the enhanced output module include: another internal module to occur before allowing the • Hardware-configurable for 32-bit operation in all internal counter to run. modes by cascading two adjacent modules Standard, free-running operation is selected by setting • Synchronous and Trigger modes of output the SYNCSEL bits to ‘00000’ and clearing the ICTRIG compare operation, with up to 30 user-selectable bit (ICxCON2<7>). Synchronous and Trigger modes trigger/sync sources available are selected any time the SYNCSEL bits are set to any • A 4-level FIFO buffer for capturing and holding value except ‘00000’. The ICTRIG bit selects either timer values for several events Synchronous or Trigger mode; setting the bit selects • Configurable interrupt generation Trigger mode operation. In both modes, the SYNCSEL • Up to 6 clock sources available for each module, bits determine the sync/trigger source. driving a separate internal 16-bit counter When the SYNCSEL bits are set to ‘00000’ and The module is controlled through two registers: ICxCON1 ICTRIG is set, the module operates in Software Trigger (Register13-1) and ICxCON2 (Register13-2). A general mode. In this case, capture operations are started by block diagram of the module is shown in Figure13-1. manually setting the TRIGSTAT bit (ICxCON2<6>). FIGURE 13-1: INPUT CAPTURE BLOCK DIAGRAM ICM<2:0> ICI<1:0>(1) Prescaler Edge Detect Logic Event and Set ICxIF Counter and Interrupt 1:1/4/16 Clock Synchronizer Logic ICx Pin(1) ICTSEL<2:0> Clock Increment 16 IC Clock Select ICxTMR 4-Level FIFO Buffer Sources 16 Trigger and Sync Logic 16 Reset Trigger and ICxBUF Sync Sources SYNCSEL<4:0> TRIGGER System Bus ICOV, ICBNE Note 1: The ICx inputs must be assigned to an available RPn pin before use. Please see Section10.4 “Peripheral Pin Select” for more information.  2010 Microchip Technology Inc. DS39905E-page 163

PIC24FJ256GA110 FAMILY 13.1.2 CASCADED (32-BIT) MODE For 32-bit cascaded operations, the setup procedure is slightly different: By default, each module operates independently with its own 16-bit timer. To increase resolution, adjacent 1. Set the IC32 bits for both modules even and odd modules can be configured to function as (ICyCON2<8> and (ICxCON2<8>), enabling the a single 32-bit module. (For example, modules 1 and 2 even-numbered module first. This ensures the are paired, as are modules 3 and 4, and so on.) The modules will start functioning in unison. odd-numbered module (ICx) provides the Least Signif- 2. Set the ICTSEL and SYNCSEL bits for both icant 16 bits of the 32-bit register pairs, and the even modules to select the same sync/trigger and module (ICy) provides the Most Significant 16 bits. time base source. Set the even module first, Wraparounds of the ICx registers cause an increment then the odd module. Both modules must use of their corresponding ICy registers. the same ICTSEL and SYNCSEL settings. Cascaded operation is configured in hardware by 3. Clear the ICTRIG bit of the even module setting the IC32 bits (ICxCON2<8>) for both modules. (ICyCON2<7>); this forces the module to run in Synchronous mode with the odd module, 13.2 Capture Operations regardless of its trigger setting. 4. Use the odd module’s ICI bits (ICxCON1<6:5>) The enhanced input capture module can be configured to the desired interrupt frequency. to capture timer values and generate interrupts on rising edges on ICx, or all transitions on ICx. Captures 5. Use the ICTRIG bit of the odd module can be configured to occur on all rising edges or just (ICxCON2<7>) to configure Trigger or some (every 4th or 16th). Interrupts can be indepen- Synchronous mode operation. dently configured to generate on each event or a Note: For Synchronous mode operation, enable subset of events. the sync source as the last step. Both To set up the module for capture operations: input capture modules are held in Reset until the sync source is enabled. 1. Configure the ICx input for one of the available Peripheral Pin Select pins. 6. Use the ICM bits of the odd module 2. If Synchronous mode is to be used, disable the (ICxCON1<2:0>) to set the desired capture sync source before proceeding. mode. 3. Make sure that any previous data has been The module is ready to capture events when the time removed from the FIFO by reading ICxBUF until base and the trigger/sync source are enabled. When the ICBNE bit (ICxCON1<3>) is cleared. the ICBNE bit (ICxCON1<3>) becomes set, at least 4. Set the SYNCSEL bits (ICxCON2<4:0>) to the one capture value is available in the FIFO. Read input desired sync/trigger source. capture values from the FIFO until the ICBNE clears to 5. Set the ICTSEL bits (ICxCON1<12:10>) for the ‘0’. desired clock source. For 32-bit operation, read both the ICxBUF and 6. Set the ICI bits (ICxCON1<6:5>) to the desired ICyBUF for the full 32-bit timer value (ICxBUF for the interrupt frequency lsw, ICyBUF for the msw). At least one capture value is 7. Select Synchronous or Trigger mode operation: available in the FIFO buffer when the odd module’s ICBNE bit (ICxCON1<3>) becomes set. Continue to a) Check that the SYNCSEL bits are not set to read the buffer registers until ICBNE is cleared ‘00000’. (perform automatically by hardware). b) For Synchronous mode, clear the ICTRIG bit (ICxCON2<7>). c) For Trigger mode, set ICTRIG and clear the TRIGSTAT bit (ICxCON2<6>). 8. Set the ICM bits (ICxCON1<2:0>) to the desired operational mode. 9. Enable the selected trigger/sync source. DS39905E-page 164  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 13-1: ICxCON1: INPUT CAPTURE x CONTROL REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — bit 15 bit 8 U-0 R/W-0 R/W-0 R-0, HCS R-0, HCS R/W-0 R/W-0 R/W-0 — ICI1 ICI0 ICOV ICBNE ICM2(1) ICM1(1) ICM0(1) bit 7 bit 0 Legend: HCS = Hardware Clearable/Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 ICSIDL: Input Capture x Module Stop in Idle Control bit 1 = Input capture module halts in CPU Idle mode 0 = Input capture module continues to operate in CPU Idle mode bit 12-10 ICTSEL<2:0>: Input Capture Timer Select bits 111 = System clock (FOSC/2) 110 = Reserved 101 = Reserved 100 = Timer1 011 = Timer5 010 = Timer4 001 = Timer2 000 = Timer3 bit 9-7 Unimplemented: Read as ‘0’ bit 6-5 ICI<1:0>: Select Number of Captures per Interrupt bits 11 = Interrupt on every fourth capture event 10 = Interrupt on every third capture event 01 = Interrupt on every second capture event 00 = Interrupt on every capture event bit 4 ICOV: Input Capture x Overflow Status Flag bit (read-only) 1 = Input capture overflow occurred 0 = No input capture overflow occurred bit 3 ICBNE: Input Capture x Buffer Empty Status bit (read-only) 1 = Input capture buffer is not empty, at least one more capture value can be read 0 = Input capture buffer is empty bit 2-0 ICM<2:0>: Input Capture Mode Select bits(1) 111 = Interrupt mode: Input capture functions as interrupt pin only when device is in Sleep or Idle mode (rising edge detect only, all other control bits are not applicable) 110 = Unused (module disabled) 101 = Prescaler Capture mode: Capture on every 16th rising edge 100 = Prescaler Capture mode: Capture on every 4th rising edge 011 = Simple Capture mode: Capture on every rising edge 010 = Simple Capture mode: Capture on every falling edge 001 = Edge Detect Capture mode: Capture on every edge (rising and falling), ICI<1:0> bits do not control interrupt generation for this mode 000 = Input capture module turned off Note 1: The ICx input must also be configured to an available RPn pin. For more information, see Section10.4 “Peripheral Pin Select”.  2010 Microchip Technology Inc. DS39905E-page 165

PIC24FJ256GA110 FAMILY REGISTER 13-2: ICxCON2: INPUT CAPTURE x CONTROL REGISTER 2 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — IC32 bit 15 bit 8 R/W-0 R/W-0, HS U-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-1 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8 IC32: Cascade Two IC Modules Enable bit (32-bit operation) 1 = ICx and ICy operate in cascade as a 32-bit module (this bit must be set in both modules) 0 = ICx functions independently as a 16-bit module bit 7 ICTRIG: ICx Trigger/Sync Select bit 1 = Trigger ICx from source designated by SYNCSELx bits 0 = Synchronize ICx with source designated by SYNCSELx bits bit 6 TRIGSTAT: Timer Trigger Status bit 1 = Timer source has been triggered and is running (set in hardware, can be set in software) 0 = Timer source has not been triggered and is being held clear bit 5 Unimplemented: Read as ‘0’ bit 4-0 SYNCSEL<4:0>: Trigger/Synchronization Source Selection bits 11111 = Reserved 11110 = Input Capture 9 11101 = Input Capture 6 11100 = CTMU(1) 11011 = A/D(1) 11010 = Comparator 3(1) 11001 = Comparator 2(1) 11000 = Comparator 1(1) 10111 = Input Capture 4 10110 = Input Capture 3 10101 = Input Capture 2 10100 = Input Capture 1 10011 = Input Capture 8 10010 = Input Capture 7 1000x = reserved 01111 = Timer5 01110 = Timer4 01101 = Timer3 01100 = Timer2 01011 = Timer1 01010 = Input Capture 5 01001 = Output Compare 9 01000 = Output Compare 8 00111 = Output Compare 7 00110 = Output Compare 6 00101 = Output Compare 5 00100 = Output Compare 4 00011 = Output Compare 3 00010 = Output Compare 2 00001 = Output Compare 1 00000 = Not synchronized to any other module Note 1: Use these inputs as trigger sources only and never as sync sources. DS39905E-page 166  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 14.0 OUTPUT COMPARE WITH In Synchronous mode, the module begins performing DEDICATED TIMER its compare or PWM operation as soon as its selected clock source is enabled. Whenever an event occurs on Note: This data sheet summarizes the features of the selected sync source, the module’s internal counter this group of PIC24F devices. It is not is reset. In Trigger mode, the module waits for a sync intended to be a comprehensive reference event from another internal module to occur before source. For more information, refer to the allowing the counter to run. “PIC24F Family Reference Manual”, Free-running mode is selected by default, or any time Section 35. “Output Compare with that the SYNCSEL bits (OCxCON2<4:0>) are set to Dedicated Timer” (DS39723) ‘00000’. Synchronous or Trigger modes are selected Devices in the PIC24FJ256GA110 family all feature any time the SYNCSEL bits are set to any value except 9independent enhanced output compare modules. ‘00000’. The OCTRIG bit (OCxCON2<7>) selects Each of these modules offers a wide range of configu- either Synchronous or Trigger mode; setting the bit ration and operating options for generating pulse trains selects Trigger mode operation. In both modes, the on internal device events, and can produce SYNCSEL bits determine the sync/trigger source. Pulse-Width Modulated (PWM) waveforms for driving 14.1.2 CASCADED (32-BIT) MODE power applications. By default, each module operates independently with Key features of the enhanced output compare module its own set of 16-Bit Timer and Duty Cycle registers. To include: increase resolution, adjacent even and odd modules • Hardware-configurable for 32-bit operation in all can be configured to function as a single 32-bit module. modes by cascading two adjacent modules (For example, modules 1 and 2 are paired, as are • Synchronous and Trigger modes of output modules 3 and 4, and so on.) The odd-numbered compare operation, with up to 30 user-selectable module (OCx) provides the Least Significant 16 bits of trigger/sync sources available the 32-bit register pairs, and the even module (OCy) • Two separate Period registers (a main register, provides the Most Significant 16 bits. Wraparounds of OCxR, and a secondary register, OCxRS) for the OCx registers cause an increment of their greater flexibility in generating pulses of varying corresponding OCy registers. widths Cascaded operation is configured in hardware by • Configurable for single pulse or continuous pulse setting the OC32 bits (OCxCON2<8>) for both generation on an output event, or continuous modules. PWM waveform generation • Up to 6 clock sources available for each module, driving a separate internal 16-bit counter 14.1 General Operating Modes 14.1.1 SYNCHRONOUS AND TRIGGER MODES By default, the enhanced output compare module oper- ates in a free-running mode. The internal, 16-bit coun- ter, OCxTMR, counts up continuously, wrapping around from FFFFh to 0000h on each overflow, with its period synchronized to the selected external clock source. Compare or PWM events are generated each time a match between the internal counter and one of the Period registers occurs.  2010 Microchip Technology Inc. DS39905E-page 167

PIC24FJ256GA110 FAMILY 14.2 Compare Operations 3. Write the rising edge value to OCxR, and the falling edge value to OCxRS. In Compare mode (Figure14-1), the enhanced output 4. Set the Timer Period register, PRy, to a value compare module can be configured for single-shot or equal to or greater than the value in OCxRS. continuous pulse generation; it can also repeatedly toggle an output pin on each timer event. 5. Set the OCM<2:0> bits for the appropriate compare operation (= 0xx). To set up the module for compare operations: 6. For Trigger mode operations, set OCTRIG to 1. Configure the OCx output for one of the enable Trigger mode. Set or clear TRIGMODE to available Peripheral Pin Select pins. configure trigger operation, and TRIGSTAT to 2. Calculate the required values for the OCxR and select a hardware or software trigger. For (for Double Compare modes) OCxRS duty cycle Synchronous mode, clear OCTRIG. registers: 7. Set the SYNCSEL<4:0> bits to configure the a) Determine the instruction clock cycle time. trigger or synchronization source. If free-running Take into account the frequency of the timer operation is required, set the SYNCSEL bits external clock to the timer source (if one is to ‘00000’ (no sync/trigger source). used) and the timer prescaler settings. 8. Select the time base source with the b) Calculate time to the rising edge of the out- OCTSEL<2:0> bits. If necessary, set the TON bit put pulse relative to the timer start value for the selected timer which enables the compare (0000h). time base to count. Synchronous mode operation starts as soon as the time base is enabled; Trigger c) Calculate the time to the falling edge of the mode operation starts after a trigger source event pulse based on the desired pulse width and occurs. the time to the rising edge of the pulse. FIGURE 14-1: OUTPUT COMPARE BLOCK DIAGRAM (16-BIT MODE) OCMx OCxCON1 OCINV OCTRIS OCTSELx OCxCON2 FLTOUT SYNCSELx FLTTRIEN TRIGSTAT FLTMD TRIGMODE ENFLT0 OCTRIG OCxR OCFLT0 Match Event OCx Pin(1) Comparator Clock Increment OC Clock Select Sources OC Output and OCxTMR Reset Fault Logic Match Event OCFA/OCFB Comparator Match Event Trigger and Trigger and Sync Sources Sync Logic OCxRS Reset OCx Interrupt Note 1: The OCx outputs must be assigned to an available RPn pin before use. Please see Section10.4 “Peripheral Pin Select” for more information. DS39905E-page 168  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY For 32-bit cascaded operation, these steps are also 14.3 Pulse-Width Modulation (PWM) necessary: Mode 1. Set the OC32 bits for both registers In PWM mode, the enhanced output compare module (OCyCON2<8> and (OCxCON2<8>). Enable can be configured for edge-aligned or center-aligned the even-numbered module first to ensure the pulse waveform generation. All PWM operations are modules will start functioning in unison. double-buffered (buffer registers are internal to the 2. Clear the OCTRIG bit of the even module module and are not mapped into SFR space). (OCyCON2<7>), so the module will run in Synchronous mode. To set up the module for PWM operations: 3. Configure the desired output and Fault settings 1. Configure the OCx output for one of the for OCyCON2. available Peripheral Pin Select pins. 4. Force the output pin for OCx to the output state 2. Calculate the desired duty cycles and load them by clearing the OCTRIS bit. into the OCxR register. 5. If Trigger mode operation is required, configure 3. Calculate the desired period and load it into the the trigger options in OCx by using the OCTRIG OCxRS register. (OCxCON2<7>), TRIGSTAT (OCxCON2<6>) 4. Select the current OCx as the synchronization and SYNCSEL (OCxCON2<4:0>) bits. source by writing 0x1F to SYNCSEL<4:0> 6. Configure the desired Compare or PWM mode (OCxCON2<4:0>) and clearing OCTRIG of operation (OCM<2:0>) for OCyCON1 first, (OCxCON2<7>). then for OCxCON1. 5. Select a clock source by writing to the Depending on the output mode selected, the module OCTSEL2<2:0> (OCxCON<12:10>) bits. holds the OCx pin in its default state and forces a tran- 6. Enable interrupts, if required, for the timer and sition to the opposite state when OCxR matches the output compare modules. The output compare timer. In Double Compare modes, OCx is forced back interrupt is required for PWM Fault pin utilization. to its default state when a match with OCxRS occurs. 7. Select the desired PWM mode in the OCM<2:0> The OCxIF interrupt flag is set after an OCxR match in (OCxCON1<2:0>) bits. Single Compare modes, and after each OCxRS match 8. If a timer is selected as a clock source, set the in Double Compare modes. TMRy prescale value and enable the time base Single-shot pulse events only occur once, but may be by setting the TON (TxCON<15>) bit. repeated by simply rewriting the value of the Note: This peripheral contains input and output OCxCON1 register. Continuous pulse events continue functions that may need to be configured indefinitely until terminated. by the Peripheral Pin Select. See Section10.4 “Peripheral Pin Select” for more information.  2010 Microchip Technology Inc. DS39905E-page 169

PIC24FJ256GA110 FAMILY FIGURE 14-2: OUTPUT COMPARE BLOCK DIAGRAM (DOUBLE-BUFFERED, 16-BIT PWM MODE) OCxCON1 OCMx OCxCON2 OCINV OCTSELx OCTRIS SYNCSELx OCxR FLTOUT TRIGSTAT FLTTRIEN TRIGMODE FLTMD OCTRIG Rollover/Reset ENFLT0 OCFLT0 OCxR Buffer OCx Pin Comparator Clock Increment Match OC Clock Event Select Sources OC Output and OCxTMR Rollover Fault Logic(1) Reset OCFA/OCFB Comparator Match Event Match Trigger and Trigger and Event Sync Logic Sync Sources OCxRS buffer Rollover/Reset OCxRS OCx Interrupt Reset Note 1: The OCx outputs must be assigned to an available RPn pin before use. Please see Section10.4 “Peripheral Pin Select” for more information. 14.3.1 PWM PERIOD 14.3.2 PWM DUTY CYCLE The PWM period is specified by writing to PRy, the The PWM duty cycle is specified by writing to the Timer Period register. The PWM period can be OCxRS and OCxR registers. The OCxRS and OCxR calculated using Equation14-1. registers can be written to at any time, but the duty cycle value is not latched until a match between PRy EQUATION 14-1: CALCULATING THE PWM and TMRy occurs (i.e., the period is complete). This PERIOD(1) provides a double buffer for the PWM duty cycle and is essential for glitchless PWM operation. PWM Period = [(PRy) + 1] • TCY • (Timer Prescale Value) Some important boundary parameters of the PWM duty where: PWM Frequency = 1/[PWM Period] cycle include: • If OCxR, OCxRS and PRy are all loaded with Note 1: Based on TCY = TOSC * 2, Doze mode 0000h, the OCx pin will remain low (0% duty and PLL are disabled. cycle). • ·If OCxRS is greater than PRy, the pin will remain Note: A PRy value of N will produce a PWM high (100% duty cycle). period of N + 1 time base count cycles. For See Example14-1 for PWM mode timing details. example, a value of 7 written into the PRy Table14-1 and Table14-2 show example PWM register will yield a period consisting of frequencies and resolutions for a device operating at 8time base cycles. 4MIPS and 10 MIPS, respectively. DS39905E-page 170  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY EQUATION 14-2: CALCULATION FOR MAXIMUM PWM RESOLUTION(1) log ( FCY ) 10 FPWM • (Timer Prescale Value) Maximum PWM Resolution (bits) = bits log (2) 10 Note1: Based on FCY = FOSC/2, Doze mode and PLL are disabled. EXAMPLE 14-1: PWM PERIOD AND DUTY CYCLE CALCULATIONS(1) 1. Find the Timer Period register value for a desired PWM frequency of 52.08 kHz, where FOSC = 8 MHz with PLL (32 MHz device clock rate) and a Timer2 prescaler setting of 1:1. TCY = 2 * TOSC = 62.5 ns PWM Period = 1/PWM Frequency = 1/52.08 kHz = 19.2s PWM Period = (PR2 + 1) • TCY • (Timer2 Prescale Value) 19.2s = (PR2 + 1) • 62.5 ns • 1 PR2 = 306 2. Find the maximum resolution of the duty cycle that can be used with a 52.08 kHz frequency and a 32MHz device clock rate: PWM Resolution = log10(FCY/FPWM)/log102) bits = (log (16 MHz/52.08 kHz)/log 2) bits 10 10 = 8.3 bits Note 1: Based on TCY = 2 * TOSC, Doze mode and PLL are disabled. TABLE 14-1: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 4 MIPS (FCY = 4 MHz)(1) PWM Frequency 7.6 Hz 61 Hz 122 Hz 977 Hz 3.9 kHz 31.3 kHz 125 kHz Timer Prescaler Ratio 8 1 1 1 1 1 1 Period Register Value FFFFh FFFFh 7FFFh 0FFFh 03FFh 007Fh 001Fh Resolution (bits) 16 16 15 12 10 7 5 Note 1: Based on FCY = FOSC/2, Doze mode and PLL are disabled. TABLE 14-2: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 16 MIPS (FCY = 16 MHz)(1) PWM Frequency 30.5 Hz 244 Hz 488 Hz 3.9 kHz 15.6 kHz 125 kHz 500 kHz Timer Prescaler Ratio 8 1 1 1 1 1 1 Period Register Value FFFFh FFFFh 7FFFh 0FFFh 03FFh 007Fh 001Fh Resolution (bits) 16 16 15 12 10 7 5 Note 1: Based on FCY = FOSC/2, Doze mode and PLL are disabled.  2010 Microchip Technology Inc. DS39905E-page 171

PIC24FJ256GA110 FAMILY REGISTER 14-1: OCxCON1: OUTPUT COMPARE x CONTROL 1 REGISTER U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 — — bit 15 bit 8 R/W-0 U-0 U-0 R/W-0, HCS R/W-0 R/W-0 R/W-0 R/W-0 ENFLT0 — — OCFLT0 TRIGMODE OCM2(1) OCM1(1) OCM0(1) bit 7 bit 0 Legend: HCS = Hardware Clearable/Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 OCSIDL: Stop Output Compare x in Idle Mode Control bit 1 = Output Compare x halts in CPU Idle mode 0 = Output Compare x continues to operate in CPU Idle mode bit 12-10 OCTSEL<2:0>: Output Compare x Timer Select bits 111 = Peripheral Clock (FCY) 110 = Reserved 101 = Reserved 100 = Timer1 011 = Timer5 010 = Timer4 001 = Timer3 000 = Timer2 bit 9-8 Unimplemented: Read as ‘0’ bit 7 ENFLT0: Fault 0 Input Enable bit 1 = Fault 0 input is enabled 0 = Fault 0 input is disabled bit 6-5 Unimplemented: Read as ‘0’ bit 4 OCFLT0: PWM Fault Condition Status bit 1 = PWM Fault condition has occurred (cleared in HW only) 0 = No PWM Fault condition has occurred (this bit is only used when OCM<2:0> = 111) bit 3 TRIGMODE: Trigger Status Mode Select bit 1 = TRIGSTAT (OCxCON2<6>) is cleared when OCxRS = OCxTMR or in software 0 = TRIGSTAT is only cleared by software bit 2-0 OCM<2:0>: Output Compare x Mode Select bits(1) 111 = Center-Aligned PWM mode on OCx(2) 110 = Edge-Aligned PWM mode on OCx(2) 101 = Double Compare Continuous Pulse mode: initialize OCx pin low, toggle OCx state continuously on alternate matches of OCxR and OCxRS 100 = Double Compare Single-Shot mode: initialize OCx pin low, toggle OCx state on matches of OCxR and OCxRS for one cycle 011 = Single Compare Continuous Pulse mode: compare events continuously toggle OCx pin 010 = Single Compare Single-Shot mode: initialize OCx pin high, compare event forces OCx pin low 001 = Single Compare Single-Shot mode: initialize OCx pin low, compare event forces OCx pin high 000 = Output compare channel is disabled Note 1: The OCx output must also be configured to an available RPn pin. For more information, see Section10.4 “Peripheral Pin Select”. 2: OCFA pin controls OC1-OC4 channels; OCFB pin controls the OC5-OC9 channels. OCxR and OCxRS are double-buffered only in PWM modes. DS39905E-page 172  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 14-2: OCxCON2: OUTPUT COMPARE x CONTROL 2 REGISTER R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 FLTMD FLTOUT FLTTRIEN OCINV — — — OC32 bit 15 bit 8 R/W-0 R/W-0, HS R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FLTMD: Fault Mode Select bit 1 = Fault mode is maintained until the Fault source is removed and the corresponding OCFLT0 bit is cleared in software 0 = Fault mode is maintained until the Fault source is removed and a new PWM period starts bit 14 FLTOUT: Fault Out bit 1 = PWM output is driven high on a Fault 0 = PWM output is driven low on a Fault bit 13 FLTTRIEN: Fault Output State Select bit 1 = Pin is forced to an output on a Fault condition 0 = Pin I/O condition is unaffected by a Fault bit 12 OCINV: OCMP Invert bit 1 = OCx output is inverted 0 = OCx output is not inverted bit 11-9 Unimplemented: Read as ‘0’ bit 8 OC32: Cascade Two OC Modules Enable bit (32-bit operation) 1 = Cascade module operation enabled 0 = Cascade module operation disabled bit 7 OCTRIG: OCx Trigger/Sync Select bit 1 = Trigger OCx from source designated by SYNCSELx bits 0 = Synchronize OCx with source designated by SYNCSELx bits bit 6 TRIGSTAT: Timer Trigger Status bit 1 = Timer source has been triggered and is running 0 = Timer source has not been triggered and is being held clear bit 5 OCTRIS: OCx Output Pin Direction Select bit 1 = OCx pin is tristated 0 = Output Compare Peripheral x connected to the OCx pin Note 1: Never use an OC module as its own trigger source, either by selecting this mode or another equivalent SYNCSEL setting. 2: Use these inputs as trigger sources only and never as sync sources.  2010 Microchip Technology Inc. DS39905E-page 173

PIC24FJ256GA110 FAMILY REGISTER 14-2: OCxCON2: OUTPUT COMPARE x CONTROL 2 REGISTER (CONTINUED) bit 4-0 SYNCSEL<4:0>: Trigger/Synchronization Source Selection bits 11111 = This OC module(1) 11110 = Input Capture 9(2) 11101 = Input Capture 6(2) 11100 = CTMU(2) 11011 = A/D(2) 11010 = Comparator 3(2) 11001 = Comparator 2(2) 11000 = Comparator 1(2) 10111 = Input Capture 4(2) 10110 = Input Capture 3(2) 10101 = Input Capture 2(2) 10100 = Input Capture 1(2) 10011 = Input Capture 8(2) 10010 = Input Capture 7(2) 1000x = reserved 01111 = Timer5 01110 = Timer4 01101 = Timer3 01100 = Timer2 01011 = Timer1 01010 = Input Capture 5(2) 01001 = Output Compare 9(1) 01000 = Output Compare 8(1) 00111 = Output Compare 7(1) 00110 = Output Compare 6(1) 00101 = Output Compare 5(1) 00100 = Output Compare 4(1) 00011 = Output Compare 3(1) 00010 = Output Compare 2(1) 00001 = Output Compare 1(1) 00000 = Not synchronized to any other module Note 1: Never use an OC module as its own trigger source, either by selecting this mode or another equivalent SYNCSEL setting. 2: Use these inputs as trigger sources only and never as sync sources. DS39905E-page 174  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 15.0 SERIAL PERIPHERAL The SPI serial interface consists of four pins: INTERFACE (SPI) • SDIx: Serial Data Input • SDOx: Serial Data Output Note: This data sheet summarizes the features of • SCKx: Shift Clock Input or Output this group of PIC24F devices. It is not • SSx: Active-Low Slave Select or Frame intended to be a comprehensive reference Synchronization I/O Pulse source. For more information, refer to the “PIC24F Family Reference Manual”, The SPI module can be configured to operate using 2, Section 23. “Serial Peripheral Interface 3 or 4 pins. In the 3-pin mode, SSx is not used. In the (SPI)” (DS39699). 2-pin mode, both SDOx and SSx are not used. Block diagrams of the module in Standard and The Serial Peripheral Interface (SPI) module is a Enhanced modes are shown in Figure15-1 and synchronous serial interface useful for communicating Figure15-2. with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, shift reg- Note: In this section, the SPI modules are isters, display drivers, A/D Converters, etc. The SPI referred to together as SPIx or separately module is compatible with Motorola’s SPI and SIOP as SPI1, SPI2 or SPI3. Special Function interfaces. All devices of the PIC24FJ256GA110 family Registers will follow a similar notation. For include three SPI modules example, SPIxCON1 and SPIxCON2 The module supports operation in two buffer modes. In refer to the control registers for any of the Standard mode, data is shifted through a single serial 3 SPI modules. buffer. In Enhanced Buffer mode, data is shifted through an 8-level FIFO buffer. Note: Do not perform read-modify-write opera- tions (such as bit-oriented instructions) on the SPIxBUF register in either Standard or Enhanced Buffer mode. The module also supports a basic framed SPI protocol while operating in either Master or Slave mode. A total of four framed SPI configurations are supported.  2010 Microchip Technology Inc. DS39905E-page 175

PIC24FJ256GA110 FAMILY To set up the SPI module for the Standard Master mode To set up the SPI module for the Standard Slave mode of operation: of operation: 1. If using interrupts: 1. Clear the SPIxBUF register. a) Clear the SPIxIF bit in the respective IFSx 2. If using interrupts: register. a) Clear the SPIxIF bit in the respective IFSx b) Set the SPIxIE bit in the respective IECx register. register. b) Set the SPIxIE bit in the respective IECx c) Write the SPIxIP bits in the respective IPCx register. register to set the interrupt priority. c) Write the SPIxIP bits in the respective IPCx 2. Write the desired settings to the SPIxCON1 and register to set the interrupt priority. SPIxCON2 registers with the MSTEN bit 3. Write the desired settings to the SPIxCON1 (SPIxCON1<5>) = 1. and SPIxCON2 registers with the MSTEN bit 3. Clear the SPIROV bit (SPIxSTAT<6>). (SPIxCON1<5>) = 0. 4. Enable SPI operation by setting the SPIEN bit 4. Clear the SMP bit. (SPIxSTAT<15>). 5. If the CKE bit is set, then the SSEN bit 5. Write the data to be transmitted to the SPIxBUF (SPIxCON1<8>) must be set to enable the SSx register. Transmission (and reception) will start pin. as soon as data is written to the SPIxBUF 6. Clear the SPIROV bit (SPIxSTAT<6>). register. 7. Enable SPI operation by setting the SPIEN bit (SPIxSTAT<15>). FIGURE 15-1: SPIx MODULE BLOCK DIAGRAM (STANDARD MODE) SCKx 1:1 to 1:8 1:1/4/16/64 Secondary Primary FCY Prescaler Prescaler SSx/FSYNCx Sync Control Select Control Clock Edge SPIxCON1<1:0> ShiftControl SPIxCON1<4:2> SDOx Enable SDIx bit 0 Master Clock SPIxSR Transfer Transfer SPIxBUF Read SPIxBUF Write SPIxBUF 16 Internal Data Bus DS39905E-page 176  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY To set up the SPI module for the Enhanced Buffer To set up the SPI module for the Enhanced Buffer Master mode of operation: Slave mode of operation: 1. If using interrupts: 1. Clear the SPIxBUF register. a) Clear the SPIxIF bit in the respective IFSx 2. If using interrupts: register. a) Clear the SPIxIF bit in the respective IFSx b) Set the SPIxIE bit in the respective IECx register. register. b) Set the SPIxIE bit in the respective IECx c) Write the SPIxIP bits in the respective IPCx register. register. c) Write the SPIxIP bits in the respective IPCx 2. Write the desired settings to the SPIxCON1 and register to set the interrupt priority. SPIxCON2 registers with the MSTEN bit 3. Write the desired settings to the SPIxCON1 and (SPIxCON1<5>) = 1. SPIxCON2 registers with the MSTEN bit 3. Clear the SPIROV bit (SPIxSTAT<6>). (SPIxCON1<5>) = 0. 4. Select Enhanced Buffer mode by setting the 4. Clear the SMP bit. SPIBEN bit (SPIxCON2<0>). 5. If the CKE bit is set, then the SSEN bit must be 5. Enable SPI operation by setting the SPIEN bit set, thus enabling the SSx pin. (SPIxSTAT<15>). 6. Clear the SPIROV bit (SPIxSTAT<6>). 6. Write the data to be transmitted to the SPIxBUF 7. Select Enhanced Buffer mode by setting the register. Transmission (and reception) will start SPIBEN bit (SPIxCON2<0>). as soon as data is written to the SPIxBUF 8. Enable SPI operation by setting the SPIEN bit register. (SPIxSTAT<15>). FIGURE 15-2: SPIx MODULE BLOCK DIAGRAM (ENHANCED MODE) SCKx 1:1 to 1:8 1:1/4/16/64 Secondary Primary FCY Prescaler Prescaler SSx/FSYNCx Sync Control Select Control Clock Edge SPIxCON1<1:0> ShiftControl SPIxCON1<4:2> SDOx Enable SDIx bit0 Master Clock SPIxSR Transfer Transfer 8-Level FIFO 8-Level FIFO Receive Buffer Transmit Buffer SPIxBUF Read SPIxBUF Write SPIxBUF 16 InternalData Bus  2010 Microchip Technology Inc. DS39905E-page 177

PIC24FJ256GA110 FAMILY REGISTER 15-1: SPIxSTAT: SPIx STATUS AND CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 R-0 R-0 R-0 SPIEN(1) — SPISIDL — — SPIBEC2 SPIBEC1 SPIBEC0 bit 15 bit 8 R-0 R/C-0, HS R-0 R/W-0 R/W-0 R/W-0 R-0 R-0 SRMPT SPIROV SRXMPT SISEL2 SISEL1 SISEL0 SPITBF SPIRBF bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SPIEN: SPIx Enable bit(1) 1 = Enables module and configures SCKx, SDOx, SDIx and SSx as serial port pins 0 = Disables module bit 14 Unimplemented: Read as ‘0’ bit 13 SPISIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-11 Unimplemented: Read as ‘0’ bit 10-8 SPIBEC<2:0>: SPIx Buffer Element Count bits (valid in Enhanced Buffer mode) Master mode: Number of SPI transfers pending. Slave mode: Number of SPI transfers unread. bit 7 SRMPT: Shift Register (SPIxSR) Empty bit (valid in Enhanced Buffer mode) 1 = SPIx Shift register is empty and ready to send or receive 0 = SPIx Shift register is not empty bit 6 SPIROV: Receive Overflow Flag bit 1 = A new byte/word is completely received and discarded. The user software has not read the previous data in the SPIxBUF register. 0 = No overflow has occurred bit 5 SRXMPT: Receive FIFO Empty bit (valid in Enhanced Buffer mode) 1 = Receive FIFO is empty 0 = Receive FIFO is not empty bit 4-2 SISEL<2:0>: SPIx Buffer Interrupt Mode bits (valid in Enhanced Buffer mode) 111 = Interrupt when SPIx transmit buffer is full (SPITBF bit is set) 110 = Interrupt when last bit is shifted into SPIxSR; as a result, the TX FIFO is empty 101 = Interrupt when the last bit is shifted out of SPIxSR; now the transmit is complete 100 = Interrupt when one data is shifted into the SPIxSR; as a result, the TX FIFO has one open spot 011 = Interrupt when SPIx receive buffer is full (SPIRBF bit set) 010 = Interrupt when SPIx receive buffer is 3/4 or more full 001 = Interrupt when data is available in receive buffer (SRMPT bit is set) 000 = Interrupt when the last data in the receive buffer is read; as a result, the buffer is empty (SRXMPT bit set) Note 1: If SPIEN = 1, these functions must be assigned to available RPn pins (or to ASCK1 for the SCK1 output) before use. See Section10.4 “Peripheral Pin Select” for more information. DS39905E-page 178  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 15-1: SPIxSTAT: SPIx STATUS AND CONTROL REGISTER (CONTINUED) bit 1 SPITBF: SPIx Transmit Buffer Full Status bit 1 = Transmit not yet started, SPIxTXB is full 0 = Transmit started, SPIxTXB is empty In Standard Buffer mode: Automatically set in hardware when CPU writes SPIxBUF location, loading SPIxTXB. Automatically cleared in hardware when SPIx module transfers data from SPIxTXB to SPIxSR. In Enhanced Buffer mode: Automatically set in hardware when CPU writes SPIxBUF location, loading the last available buffer location. Automatically cleared in hardware when a buffer location is available for a CPU write. bit 0 SPIRBF: SPIx Receive Buffer Full Status bit 1 = Receive complete, SPIxRXB is full 0 = Receive is not complete, SPIxRXB is empty In Standard Buffer mode: Automatically set in hardware when SPIx transfers data from SPIxSR to SPIxRXB. Automatically cleared in hardware when core reads SPIxBUF location, reading SPIxRXB. In Enhanced Buffer mode: Automatically set in hardware when SPIx transfers data from SPIxSR to buffer, filling the last unread buffer location. Automatically cleared in hardware when a buffer location is available for a transfer from SPIxSR. Note 1: If SPIEN = 1, these functions must be assigned to available RPn pins (or to ASCK1 for the SCK1 output) before use. See Section10.4 “Peripheral Pin Select” for more information.  2010 Microchip Technology Inc. DS39905E-page 179

PIC24FJ256GA110 FAMILY REGISTER 15-2: SPIXCON1: SPIx CONTROL REGISTER 1 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — DISSCK(1) DISSDO(2) MODE16 SMP CKE(3) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SSEN(4) CKP MSTEN SPRE2 SPRE1 SPRE0 PPRE1 PPRE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 DISSCK: Disable SCKx pin bit (SPI Master modes only)(1) 1 = Internal SPI clock is disabled; pin functions as I/O 0 = Internal SPI clock is enabled bit 11 DISSDO: Disable SDOx pin bit(2) 1 = SDOx pin is not used by module; pin functions as I/O 0 = SDOx pin is controlled by the module bit 10 MODE16: Word/Byte Communication Select bit 1 = Communication is word-wide (16 bits) 0 = Communication is byte-wide (8 bits) bit 9 SMP: SPIx Data Input Sample Phase bit Master mode: 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time Slave mode: SMP must be cleared when SPIx is used in Slave mode. bit 8 CKE: SPIx Clock Edge Select bit(3) 1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6) 0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6) bit 7 SSEN: Slave Select Enable (Slave mode) bit(4) 1 = SSx pin used for Slave mode 0 = SSx pin not used by module; pin controlled by port function bit 6 CKP: Clock Polarity Select bit 1 = Idle state for clock is a high level; active state is a low level 0 = Idle state for clock is a low level; active state is a high level bit 5 MSTEN: Master Mode Enable bit 1 = Master mode 0 = Slave mode Note 1: If DISSCK = 0, SCKx must be configured to an available RPn pin (or to ASCK1 for SPI1). See Section10.4 “Peripheral Pin Select” for more information. 2: If DISSDO = 0, SDOx must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information. 3: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed SPI modes (FRMEN = 1). 4: If SSEN = 1, SSx must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information. DS39905E-page 180  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 15-2: SPIXCON1: SPIx CONTROL REGISTER 1 (CONTINUED) bit 4-2 SPRE<2:0>: Secondary Prescale bits (Master mode) 111 = Secondary prescale 1:1 110 = Secondary prescale 2:1 ... 000 = Secondary prescale 8:1 bit 1-0 PPRE<1:0>: Primary Prescale bits (Master mode) 11 = Primary prescale 1:1 10 = Primary prescale 4:1 01 = Primary prescale 16:1 00 = Primary prescale 64:1 Note 1: If DISSCK = 0, SCKx must be configured to an available RPn pin (or to ASCK1 for SPI1). See Section10.4 “Peripheral Pin Select” for more information. 2: If DISSDO = 0, SDOx must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information. 3: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed SPI modes (FRMEN = 1). 4: If SSEN = 1, SSx must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information. REGISTER 15-3: SPIxCON2: SPIx CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 FRMEN SPIFSD SPIFPOL — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — SPIFE SPIBEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FRMEN: Framed SPIx Support bit 1 = Framed SPIx support enabled 0 = Framed SPIx support disabled bit 14 SPIFSD: Frame Sync Pulse Direction Control on SSx Pin bit 1 = Frame sync pulse input (slave) 0 = Frame sync pulse output (master) bit 13 SPIFPOL: Frame Sync Pulse Polarity bit (Frame mode only) 1 = Frame sync pulse is active-high 0 = Frame sync pulse is active-low bit 12-2 Unimplemented: Read as ‘0’ bit 1 SPIFE: Frame Sync Pulse Edge Select bit 1 = Frame sync pulse coincides with first bit clock 0 = Frame sync pulse precedes first bit clock bit 0 SPIBEN: Enhanced Buffer Enable bit 1 = Enhanced Buffer enabled 0 = Enhanced Buffer disabled (Legacy mode)  2010 Microchip Technology Inc. DS39905E-page 181

PIC24FJ256GA110 FAMILY FIGURE 15-3: SPI MASTER/SLAVE CONNECTION (STANDARD MODE) PROCESSOR 1 (SPI Master) PROCESSOR 2 (SPI Slave) SDOx SDIx Serial Receive Buffer Serial Receive Buffer (SPIxRXB) (SPIxRXB) Shift Register SDIx SDOx Shift Register (SPIxSR) (SPIxSR) MSb LSb MSb LSb Serial Transmit Buffer Serial Transmit Buffer (SPIxTXB) (SPIxTXB) Serial Clock SPIx Buffer SCKx SCKx SPIx Buffer (SPIxBUF)(2) (SPIxBUF)(2) SSx(1) MSTEN (SPIxCON1<5>) = 1) SSEN (SPIxCON1<7>) = 1 and MSTEN (SPIxCON1<5>) = 0 Note 1: Using the SSx pin in Slave mode of operation is optional. 2: User must write transmit data to read received data from SPIxBUF. The SPIxTXB and SPIxRXB registers are memory mapped to SPIxBUF. FIGURE 15-4: SPI MASTER/SLAVE CONNECTION (ENHANCED BUFFER MODES) PROCESSOR 1 (SPI Enhanced Buffer Master) PROCESSOR 2 (SPI Enhanced Buffer Slave) SDOx SDIx SDIx SDOx Shift Register Shift Register (SPIxSR) (SPIxSR) MSb LSb MSb LSb 8-Level FIFO Buffer 8-Level FIFO Buffer SPIx Buffer Serial Clock SPIx Buffer (SPIxBUF)(2) SCKx SCKx (SPIxBUF)(2) SSx SSx(1) MSTEN (SPIxCON1<5>) = 1 and SSEN (SPIxCON1<7>) = 1, SPIBEN (SPIxCON2<0>) = 1 MSTEN (SPIxCON1<5>) = 0 and SPIBEN (SPIxCON2<0>) = 1 Note 1: Using the SSx pin in Slave mode of operation is optional. 2: User must write transmit data to read received data from SPIxBUF. The SPIxTXB and SPIxRXB registers are memory mapped to SPIxBUF. DS39905E-page 182  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 15-5: SPI MASTER, FRAME MASTER CONNECTION DIAGRAM PIC24F PROCESSOR 2 (SPI Master, Frame Master) SDOx SDIx SDIx SDOx Serial Clock SCKx SCKx SSx SSx Frame Sync Pulse FIGURE 15-6: SPI MASTER, FRAME SLAVE CONNECTION DIAGRAM PIC24F PROCESSOR 2 (SPI Master, Frame Slave) SDOx SDIx SDIx SDOx Serial Clock SCKx SCKx SSx SSx Frame Sync Pulse FIGURE 15-7: SPI SLAVE, FRAME MASTER CONNECTION DIAGRAM PIC24F PROCESSOR 2 (SPI Slave, Frame Master) SDOx SDIx SDIx SDOx Serial Clock SCKx SCKx SSx SSx Frame Sync. Pulse FIGURE 15-8: SPI SLAVE, FRAME SLAVE CONNECTION DIAGRAM PIC24F PROCESSOR 2 (SPI Slave, Frame Slave) SDOx SDIx SDIx SDOx Serial Clock SCKx SCKx SSx SSx Frame Sync Pulse  2010 Microchip Technology Inc. DS39905E-page 183

PIC24FJ256GA110 FAMILY EQUATION 15-1: RELATIONSHIP BETWEEN DEVICE AND SPI CLOCK SPEED(1) FCY FSCK = Primary Prescaler * Secondary Prescaler Note1: Based on FCY = FOSC/2, Doze mode and PLL are disabled. TABLE 15-1: SAMPLE SCK FREQUENCIES(1,2) Secondary Prescaler Settings FCY = 16 MHz 1:1 2:1 4:1 6:1 8:1 Primary Prescaler Settings 1:1 Invalid 8000 4000 2667 2000 4:1 4000 2000 1000 667 500 16:1 1000 500 250 167 125 64:1 250 125 63 42 31 FCY = 5 MHz Primary Prescaler Settings 1:1 5000 2500 1250 833 625 4:1 1250 625 313 208 156 16:1 313 156 78 52 39 64:1 78 39 20 13 10 Note 1: Based on FCY = FOSC/2, Doze mode and PLL are disabled. 2: SCKx frequencies shown in kHz. DS39905E-page 184  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 16.0 INTER-INTEGRATED CIRCUIT 16.2 Communicating as a Master in a (I2C™) Single Master Environment The details of sending a message in Master mode Note: This data sheet summarizes the features of depends on the communications protocol for the device this group of PIC24F devices. It is not being communicated with. Typically, the sequence of intended to be a comprehensive reference events is as follows: source. For more information, refer to the “PIC24F Family Reference Manual”, 1. Assert a Start condition on SDAx and SCLx. Section 24. “Inter-Integrated Circuit 2. Send the I2C device address byte to the slave (I2C™)” (DS39702). with a write indication. The Inter-Integrated Circuit (I2C) module is a serial inter- 3. Wait for and verify an Acknowledge from the slave. face useful for communicating with other peripheral or microcontroller devices. These peripheral devices may 4. Send the first data byte (sometimes known as be serial EEPROMs, display drivers, A/D Converters, the command) to the slave. etc. 5. Wait for and verify an Acknowledge from the The I2C module supports these features: slave. 6. Send the serial memory address low byte to the • Independent master and slave logic slave. • 7-bit and 10-bit device addresses 7. Repeat Steps 4 and 5 until all data bytes are • General call address, as defined in the I2C protocol sent. • Clock stretching to provide delays for the 8. Assert a Repeated Start condition on SDAx and processor to respond to a slave data request SCLx. • Both 100kHz and 400kHz bus specifications. 9. Send the device address byte to the slave with • Configurable address masking a read indication. • Multi-Master modes to prevent loss of messages 10. Wait for and verify an Acknowledge from the in arbitration slave. • Bus Repeater mode, allowing the acceptance of 11. Enable master reception to receive serial all messages as a slave regardless of the address memory data. • Automatic SCL 12. Generate an ACK or NACK condition at the end A block diagram of the module is shown in Figure16-1. of a received byte of data. 13. Generate a Stop condition on SDAx and SCLx. 16.1 Peripheral Remapping Options The I2C modules are tied to fixed pin assignments and cannot be reassigned to alternate pins using Peripheral Pin Select. To allow some flexibility with peripheral multiplexing, the I2C2 module in 100-pin devices can be reassigned to the alternate pins designated as ASCL2 and ASDA2 during device configuration. Pin assignment is controlled by the I2C2SEL Configu- ration bit; programming this bit (=0) multiplexes the module to the ASCL2 and ASDA2 pins.  2010 Microchip Technology Inc. DS39905E-page 185

PIC24FJ256GA110 FAMILY FIGURE 16-1: I2C™ BLOCK DIAGRAM Internal Data Bus I2CxRCV Read Shift SCLx Clock I2CxRSR LSB SDAx Address Match Match Detect Write I2CxMSK Write Read I2CxADD Read Start and Stop Bit Detect Write Start and Stop Bit Generation I2CxSTAT c ogi Read Collision ol L Write Detect ntr o C I2CxCON Acknowledge Generation Read Clock Stretching Write I2CxTRN LSB Read ShiftClock Reload Control Write BRG Down Counter I2CxBRG Read TCY/2 DS39905E-page 186  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 16.3 Setting Baud Rate When 16.4 Slave Address Masking Operating as a Bus Master The I2CxMSK register (Register16-3) designates To compute the Baud Rate Generator reload value, use address bit positions as “don’t care” for both 7-Bit and Equation16-1. 10-Bit Addressing modes. Setting a particular bit loca- tion (= 1) in the I2CxMSK register causes the slave EQUATION 16-1: COMPUTING BAUD RATE module to respond whether the corresponding address RELOAD VALUE(1,2) bit value is a ‘0’ or a ‘1’. For example, when I2CxMSK is set to ‘00010000’, the slave module will detect both FCY FSCL = ---------------------------------------------------------------------- addresses: ‘0000000’ and ‘0010000’. FCY I2CxBRG+1+------------------------------ 10000000 To enable address masking, the IPMI (Intelligent or Peripheral Management Interface) must be disabled by FCY FCY  I2CxBRG = ------------–------------------------------ –1 clearing the IPMIEN bit (I2CxCON<11>). FSCL 10000000 Note: As a result of changes in the I2C™ proto- Note 1: Based on FCY = FOSC/2, Doze mode and PLL col, the addresses in Table16-2 are are disabled. reserved and will not be Acknowledged in 2: These clock rate values are for guidance only. Slave mode. This includes any address The actual clock rate can be affected by various system level parameters. The actual clock rate mask settings that include any of these should be measured in its intended application. addresses. TABLE 16-1: I2C™ CLOCK RATES(1,2) I2CxBRG Value Required System Actual FCY FSCL (Decimal) (Hexadecimal) FSCL 100kHz 16MHz 157 9D 100kHz 100kHz 8MHz 78 4E 100kHz 100kHz 4MHz 39 27 99kHz 400kHz 16MHz 37 25 404kHz 400kHz 8MHz 18 12 404kHz 400kHz 4MHz 9 9 385kHz 400kHz 2MHz 4 4 385kHz 1MHz 16MHz 13 D 1.026MHz 1MHz 8MHz 6 6 1.026MHz 1MHz 4MHz 3 3 0.909MHz Note 1: Based on FCY = FOSC/2, Doze mode and PLL are disabled. 2: These clock rate values are for guidance only. The actual clock rate can be affected by various system level parameters. The actual clock rate should be measured in its intended application. TABLE 16-2: I2C™ RESERVED ADDRESSES(1) Slave Address R/W Bit Description 0000 000 0 General Call Address(2) 0000 000 1 Start Byte 0000 001 x Cbus Address 0000 010 x Reserved 0000 011 x Reserved 0000 1xx x HS Mode Master Code 1111 1xx x Reserved 1111 0xx x 10-Bit Slave Upper Byte(3) Note 1: The address bits listed here will never cause an address match, independent of address mask settings. 2: The address will be Acknowledged only if GCEN=1. 3: Match on this address can only occur on the upper byte in 10-Bit Addressing mode.  2010 Microchip Technology Inc. DS39905E-page 187

PIC24FJ256GA110 FAMILY REGISTER 16-1: I2CxCON: I2Cx CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-1, HC R/W-0 R/W-0 R/W-0 R/W-0 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 I2CEN: I2Cx Enable bit 1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins 0 = Disables I2Cx module. All I2C pins are controlled by port functions. bit 14 Unimplemented: Read as ‘0’ bit 13 I2CSIDL: Stop in Idle Mode bit 1 = Discontinues module operation when device enters an Idle mode 0 = Continues module operation in Idle mode bit 12 SCLREL: SCLx Release Control bit (when operating as I2C Slave) 1 = Releases SCLx clock 0 = Holds SCLx clock low (clock stretch) If STREN = 1: Bit is R/W (i.e., software may write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware clear at beginning of slave transmission. Hardware clear at end of slave reception. If STREN = 0: Bit is R/S (i.e., software may only write ‘1’ to release clock). Hardware clear at beginning of slave transmission. bit 11 IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit 1 = IPMI Support mode is enabled; all addresses Acknowledged 0 = IPMI mode disabled bit 10 A10M: 10-Bit Slave Addressing bit 1 = I2CxADD is a 10-bit slave address 0 = I2CxADD is a 7-bit slave address bit 9 DISSLW: Disable Slew Rate Control bit 1 = Slew rate control disabled 0 = Slew rate control enabled bit 8 SMEN: SMBus Input Levels bit 1 = Enables I/O pin thresholds compliant with SMBus specification 0 = Disables SMBus input thresholds bit 7 GCEN: General Call Enable bit (when operating as I2C slave) 1 = Enables interrupt when a general call address is received in the I2CxRSR (module is enabled for reception) 0 = General call address disabled bit 6 STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave) Used in conjunction with the SCLREL bit. 1 = Enables software or receive clock stretching 0 = Disables software or receive clock stretching DS39905E-page 188  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 16-1: I2CxCON: I2Cx CONTROL REGISTER (CONTINUED) bit 5 ACKDT: Acknowledge Data bit (When operating as I2C master. Applicable during master receive.) Value that will be transmitted when the software initiates an Acknowledge sequence. 1 = Sends NACK during Acknowledge 0 = Sends ACK during Acknowledge bit 4 ACKEN: Acknowledge Sequence Enable bit (When operating as I2C master. Applicable during master receive.) 1 = Initiates Acknowledge sequence on SDAx and SCLx pins and transmits ACKDT data bit. Hardware clear at end of master Acknowledge sequence. 0 = Acknowledge sequence not in progress bit 3 RCEN: Receive Enable bit (when operating as I2C master) 1 = Enables Receive mode for I2C. Hardware clear at end of eighth bit of master receive data byte. 0 = Receives sequence not in progress bit 2 PEN: Stop Condition Enable bit (when operating as I2C master) 1 = Initiates Stop condition on SDAx and SCLx pins. Hardware clear at end of master Stop sequence. 0 = Stop condition not in progress bit 1 RSEN: Repeated Start Condition Enabled bit (when operating as I2C master) 1 = Initiates Repeated Start condition on SDAx and SCLx pins. Hardware clear at end of master Repeated Start sequence. 0 = Repeated Start condition not in progress bit 0 SEN: Start Condition Enabled bit (when operating as I2C master) 1 = Initiates Start condition on SDAx and SCLx pins. Hardware clear at end of master Start sequence. 0 = Start condition not in progress  2010 Microchip Technology Inc. DS39905E-page 189

PIC24FJ256GA110 FAMILY REGISTER 16-2: I2CxSTAT: I2Cx STATUS REGISTER R-0, HSC R-0, HSC U-0 U-0 U-0 R/C-0, HS R-0, HSC R-0, HSC ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 bit 15 bit 8 R/C-0, HS R/C-0, HS R-0, HSC R/C-0, HSC R/C-0, HSC R-0, HSC R-0, HSC R-0, HSC IWCOL I2COV D/A P S R/W RBF TBF bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ACKSTAT: Acknowledge Status bit 1 = NACK was detected last 0 = ACK was detected last Hardware set or clear at end of Acknowledge. bit 14 TRSTAT: Transmit Status bit (When operating as I2C master. Applicable to master transmit operation.) 1 = Master transmit is in progress (8 bits + ACK) 0 = Master transmit is not in progress Hardware set at beginning of master transmission. Hardware clear at end of slave Acknowledge. bit 13-11 Unimplemented: Read as ‘0’ bit 10 BCL: Master Bus Collision Detect bit 1 = A bus collision has been detected during a master operation 0 = No collision Hardware set at detection of bus collision. bit 9 GCSTAT: General Call Status bit 1 = General call address was received 0 = General call address was not received Hardware set when address matches general call address. Hardware clear at Stop detection. bit 8 ADD10: 10-Bit Address Status bit 1 = 10-bit address was matched 0 = 10-bit address was not matched Hardware set at match of 2nd byte of matched 10-bit address. Hardware clear at Stop detection. bit 7 IWCOL: Write Collision Detect bit 1 = An attempt to write to the I2CxTRN register failed because the I2C module is busy 0 = No collision Hardware set at occurrence of write to I2CxTRN while busy (cleared by software). bit 6 I2COV: Receive Overflow Flag bit 1 = A byte was received while the I2CxRCV register is still holding the previous byte 0 = No overflow Hardware set at attempt to transfer I2CxRSR to I2CxRCV (cleared by software). bit 5 D/A: Data/Address bit (when operating as I2C slave) 1 = Indicates that the last byte received was data 0 = Indicates that the last byte received was device address Hardware clear at device address match. Hardware set after a transmission finishes or by reception of the slave byte. DS39905E-page 190  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 16-2: I2CxSTAT: I2Cx STATUS REGISTER (CONTINUED) bit 4 P: Stop bit 1 = Indicates that a Stop bit has been detected last 0 = Stop bit was not detected last Hardware set or clear when Start, Repeated Start or Stop detected. bit 3 S: Start bit 1 = Indicates that a Start (or Repeated Start) bit has been detected last 0 = Start bit was not detected last Hardware set or clear when Start, Repeated Start or Stop detected. bit 2 R/W: Read/Write Information bit (when operating as I2C slave) 1 = Read – indicates data transfer is output from slave 0 = Write – indicates data transfer is input to slave Hardware set or clear after reception of I2C device address byte. bit 1 RBF: Receive Buffer Full Status bit 1 = Receive complete, I2CxRCV is full 0 = Receive not complete, I2CxRCV is empty Hardware set when I2CxRCV is written with received byte. Hardware clear when software reads I2CxRCV. bit 0 TBF: Transmit Buffer Full Status bit 1 = Transmit in progress, I2CxTRN is full 0 = Transmit complete, I2CxTRN is empty Hardware set when software writes I2CxTRN. Hardware clear at completion of data transmission.  2010 Microchip Technology Inc. DS39905E-page 191

PIC24FJ256GA110 FAMILY REGISTER 16-3: I2CxMSK: I2Cx SLAVE MODE ADDRESS MASK REGISTER U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — AMSK9 AMSK8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 AMSK7 AMSK6 AMSK5 AMSK4 AMSK3 AMSK2 AMSK1 AMSK0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 AMSK<9:0>: Mask for Address Bit x Select bits 1 = Enable masking for bit x of incoming message address; bit match not required in this position 0 = Disable masking for bit x; bit match required in this position DS39905E-page 192  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 17.0 UNIVERSAL ASYNCHRONOUS • Fully Integrated Baud Rate Generator with 16-Bit RECEIVER TRANSMITTER Prescaler • Baud Rates Ranging from 1Mbps to 15bps at (UART) 16MIPS Note: This data sheet summarizes the features of • 4-Deep, First-In-First-Out (FIFO) Transmit Data this group of PIC24F devices. It is not Buffer intended to be a comprehensive reference • 4-Deep FIFO Receive Data Buffer source. For more information, refer to the • Parity, Framing and Buffer Overrun Error Detection “PIC24F Family Reference Manual”, • Support for 9-Bit mode with Address Detect Section 21. “UART” (DS39708). (9th bit = 1) The Universal Asynchronous Receiver Transmitter • Transmit and Receive Interrupts (UART) module is one of the serial I/O modules available • Loopback mode for Diagnostic Support in the PIC24F device family. The UART is a full-duplex • Support for Sync and Break Characters asynchronous system that can communicate with • Supports Automatic Baud Rate Detection peripheral devices, such as personal computers, LIN, • IrDA Encoder and Decoder Logic RS-232 and RS-485 interfaces. The module also • 16x Baud Clock Output for IrDA Support supports a hardware flow control option with the UxCTS and UxRTS pins, and also includes an IrDA® encoder A simplified block diagram of the UART is shown in and decoder. Figure17-1. The UART module consists of these key The primary features of the UART module are: important hardware elements: • Baud Rate Generator • Full-Duplex, 8 or 9-Bit Data Transmission through the UxTX and UxRX Pins • Asynchronous Transmitter • Even, Odd or No Parity Options (for 8-bit data) • Asynchronous Receiver • One or Two Stop bits • Hardware Flow Control Option with UxCTS and UxRTS Pins FIGURE 17-1: UART SIMPLIFIED BLOCK DIAGRAM Baud Rate Generator IrDA® Hardware Flow Control UxRTS/BCLKx UxCTS UARTx Receiver UxRX UARTx Transmitter UxTX Note: The UART inputs and outputs must all be assigned to available RPn pins before use. Please see Section10.4 “Peripheral Pin Select” for more information.  2010 Microchip Technology Inc. DS39905E-page 193

PIC24FJ256GA110 FAMILY 17.1 UART Baud Rate Generator (BRG) The maximum baud rate (BRGH = 0) possible is FCY/16 (for UxBRG=0) and the minimum baud rate The UART module includes a dedicated 16-bit Baud possible is FCY/(16 * 65536). Rate Generator. The UxBRG register controls the Equation17-2 shows the formula for computation of period of a free-running, 16-bit timer. Equation17-1 the baud rate with BRGH = 1. shows the formula for computation of the baud rate with BRGH=0. EQUATION 17-2: UART BAUD RATE WITH EQUATION 17-1: UART BAUD RATE WITH BRGH = 1(1,2) BRGH = 0(1,2) FCY Baud Rate = FCY 4 • (UxBRG + 1) Baud Rate = 16 • (UxBRG + 1) FCY UxBRG = – 1 4 • Baud Rate UxBRG = FCY – 1 16 • Baud Rate Note 1: FCY denotes the instruction cycle clock frequency. Note 1: FCY denotes the instruction cycle clock 2: Based on FCY = FOSC/2, Doze mode frequency (FOSC/2). and PLL are disabled. 2: Based on FCY = FOSC/2, Doze mode and PLL are disabled. The maximum baud rate (BRGH = 1) possible is FCY/4 (for UxBRG=0) and the minimum baud rate possible Example17-1 shows the calculation of the baud rate is FCY/(4 * 65536). error for the following conditions: Writing a new value to the UxBRG register causes the BRG timer to be reset (cleared). This ensures the BRG • FCY = 4 MHz does not wait for a timer overflow before generating the • Desired Baud Rate = 9600 new baud rate. EXAMPLE 17-1: BAUD RATE ERROR CALCULATION (BRGH = 0)(1) Desired Baud Rate = FCY/(16 (UxBRG + 1)) Solving for UxBRG value: UxBRG = ((FCY/Desired Baud Rate)/16) – 1 UxBRG = ((4000000/9600)/16) – 1 UxBRG = 25 Calculated Baud Rate = 4000000/(16 (25 + 1)) = 9615 Error = (Calculated Baud Rate – Desired Baud Rate) Desired Baud Rate = (9615 – 9600)/9600 = 0.16% Note 1: Based on FCY = FOSC/2, Doze mode and PLL are disabled. DS39905E-page 194  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 17.2 Transmitting in 8-Bit Data Mode 17.5 Receiving in 8-Bit or 9-Bit Data Mode 1. Set up the UART: a) Write appropriate values for data, parity and 1. Set up the UART (as described in Section17.2 Stop bits. “Transmitting in 8-Bit Data Mode”). b) Write appropriate baud rate value to the 2. Enable the UART. UxBRG register. 3. A receive interrupt will be generated when one c) Set up transmit and receive interrupt enable or more data characters have been received as and priority bits. per interrupt control bit, URXISELx. 2. Enable the UART. 4. Read the OERR bit to determine if an overrun 3. Set the UTXEN bit (causes a transmit interrupt error has occurred. The OERR bit must be reset two cycles after being set). in software. 4. Write data byte to lower byte of UxTXREG word. 5. Read UxRXREG. The value will be immediately transferred to the The act of reading the UxRXREG character will move Transmit Shift Register (TSR) and the serial bit the next character to the top of the receive FIFO, stream will start shifting out with the next rising including a new set of PERR and FERR values. edge of the baud clock. 5. Alternately, the data byte may be transferred 17.6 Operation of UxCTS and UxRTS while UTXEN=0, and then the user may set Control Pins UTXEN. This will cause the serial bit stream to begin immediately because the baud clock will UARTx Clear to Send (UxCTS) and Request to Send start from a cleared state. (UxRTS) are the two hardware controlled pins that are 6. A transmit interrupt will be generated as per associated with the UART module. These two pins interrupt control bit, UTXISELx. allow the UART to operate in Simplex and Flow Control mode. They are implemented to control the transmis- 17.3 Transmitting in 9-Bit Data Mode sion and reception between the Data Terminal Equipment (DTE). The UEN<1:0> bits in the UxMODE 1. Set up the UART (as described in Section17.2 register configure these pins. “Transmitting in 8-Bit Data Mode”). 2. Enable the UART. 17.7 Infrared Support 3. Set the UTXEN bit (causes a transmit interrupt). The UART module provides two types of infrared UART 4. Write UxTXREG as a 16-bit value only. support: one is the IrDA clock output to support exter- 5. A word write to UxTXREG triggers the transfer nal IrDA encoder and decoder device (legacy module of the 9-bit data to the TSR. The serial bit stream support), and the other is the full implementation of the will start shifting out with the first rising edge of IrDA encoder and decoder. Note that because the IrDA the baud clock. modes require a 16x baud clock, they will only work 6. A transmit interrupt will be generated as per the when the BRGH bit (UxMODE<3>) is ‘0’. setting of control bit, UTXISELx. 17.7.1 IrDA CLOCK OUTPUT FOR 17.4 Break and Sync Transmit EXTERNAL IrDA SUPPORT Sequence To support external IrDA encoder and decoder devices, the BCLKx pin (same as the UxRTS pin) can be The following sequence will send a message frame configured to generate the 16x baud clock. When header made up of a Break, followed by an Auto-Baud UEN<1:0> = 11, the BCLKx pin will output the 16x Sync byte. baud clock if the UART module is enabled. It can be 1. Configure the UART for the desired mode. used to support the IrDA codec chip. 2. Set UTXEN and UTXBRK to set up the Break 17.7.2 BUILT-IN IrDA ENCODER AND character. DECODER 3. Load the UxTXREG with a dummy character to initiate transmission (value is ignored). The UART has full implementation of the IrDA encoder 4. Write ‘55h’ to UxTXREG; this loads the Sync and decoder as part of the UART module. The built-in character into the transmit FIFO. IrDA encoder and decoder functionality is enabled using the IREN bit (UxMODE<12>). When enabled 5. After the Break has been sent, the UTXBRK bit (IREN = 1), the receive pin (UxRX) acts as the input is reset by hardware. The Sync character now from the infrared receiver. The transmit pin (UxTX) acts transmits. as the output to the infrared transmitter.  2010 Microchip Technology Inc. DS39905E-page 195

PIC24FJ256GA110 FAMILY REGISTER 17-1: UxMODE: UARTx MODE REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 UARTEN(1) — USIDL IREN(2) RTSMD — UEN1 UEN0 bit 15 bit 8 R/C-0, HC R/W-0 R/W-0, HC R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL bit 7 bit 0 Legend: C = Clearable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 UARTEN: UARTx Enable bit(1) 1 = UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0> 0 = UARTx is disabled; all UARTx pins are controlled by port latches; UARTx power consumption is minimal bit 14 Unimplemented: Read as ‘0’ bit 13 USIDL: Stop in Idle Mode bit 1 = Discontinue module operation when the device enters Idle mode 0 = Continue module operation in Idle mode bit 12 IREN: IrDA® Encoder and Decoder Enable bit(2) 1 = IrDA encoder and decoder enabled 0 = IrDA encoder and decoder disabled bit 11 RTSMD: Mode Selection for UxRTS Pin bit 1 = UxRTS pin in Simplex mode 0 = UxRTS pin in Flow Control mode bit 10 Unimplemented: Read as ‘0’ bit 9-8 UEN<1:0>: UARTx Enable bits 11 = UxTX, UxRX and BCLKx pins are enabled and used; UxCTS pin controlled by port latches 10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used 01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin controlled by port latches 00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLKx pins controlled by port latches bit 7 WAKE: Wake-up on Start Bit Detect During Sleep Mode Enable bit 1 = UARTx will continue to sample the UxRX pin; interrupt generated on falling edge, bit cleared in hardware on following rising edge 0 = No wake-up enabled bit 6 LPBACK: UARTx Loopback Mode Select bit 1 = Enable Loopback mode 0 = Loopback mode is disabled bit 5 ABAUD: Auto-Baud Enable bit 1 = Enable baud rate measurement on the next character – requires reception of a Sync field (55h); cleared in hardware upon completion 0 = Baud rate measurement disabled or completed Note 1: If UARTEN = 1, the peripheral inputs and outputs must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information. 2: This feature is only available for the 16x BRG mode (BRGH=0). DS39905E-page 196  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 17-1: UxMODE: UARTx MODE REGISTER (CONTINUED) bit 4 RXINV: Receive Polarity Inversion bit 1 = UxRX Idle state is ‘0’ 0 = UxRX Idle state is ‘1’ bit 3 BRGH: High Baud Rate Enable bit 1 = High-Speed mode (baud clock generated from FCY/4) 0 = Standard mode (baud clock generated from FCY/16) bit 2-1 PDSEL<1:0>: Parity and Data Selection bits 11 = 9-bit data, no parity 10 = 8-bit data, odd parity 01 = 8-bit data, even parity 00 = 8-bit data, no parity bit 0 STSEL: Stop Bit Selection bit 1 = Two Stop bits 0 = One Stop bit Note 1: If UARTEN = 1, the peripheral inputs and outputs must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information. 2: This feature is only available for the 16x BRG mode (BRGH=0).  2010 Microchip Technology Inc. DS39905E-page 197

PIC24FJ256GA110 FAMILY REGISTER 17-2: UxSTA: UARTx STATUS AND CONTROL REGISTER R/W-0 R/W-0 R/W-0 U-0 R/W-0 HC R/W-0 R-0 R-1 UTXISEL1 UTXINV(1) UTXISEL0 — UTXBRK UTXEN(2) UTXBF TRMT bit 15 bit 8 R/W-0 R/W-0 R/W-0 R-1 R-0 R-0 R/C-0 R-0 URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA bit 7 bit 0 Legend: C = Clearable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15,13 UTXISEL<1:0>: Transmission Interrupt Mode Selection bits 11 = Reserved; do not use 10 = Interrupt when a character is transferred to the Transmit Shift Register (TSR), and as a result, the transmit buffer becomes empty 01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit operations are completed 00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is at least one character open in the transmit buffer) bit 14 UTXINV: IrDA® Encoder Transmit Polarity Inversion bit(1) IREN = 0: 1 = UxTX Idle ‘0’ 0 = UxTX Idle ‘1’ IREN = 1: 1 = UxTX Idle ‘1’ 0 = UxTX Idle ‘0’ bit 12 Unimplemented: Read as ‘0’ bit 11 UTXBRK: Transmit Break bit 1 = Send Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit; cleared by hardware upon completion 0 = Sync Break transmission disabled or completed bit 10 UTXEN: Transmit Enable bit(2) 1 = Transmit enabled; UxTX pin controlled by UARTx 0 = Transmit disabled; any pending transmission is aborted and the buffer is reset, UxTX pin controlled by port bit 9 UTXBF: Transmit Buffer Full Status bit (read-only) 1 = Transmit buffer is full 0 = Transmit buffer is not full; at least one more character can be written bit 8 TRMT: Transmit Shift Register Empty bit (read-only) 1 = Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed) 0 = Transmit Shift Register is not empty, a transmission is in progress or queued bit 7-6 URXISEL<1:0>: Receive Interrupt Mode Selection bits 11 = Interrupt is set on RSR transfer, making the receive buffer full (i.e., has 4 data characters) 10 = Interrupt is set on RSR transfer, making the receive buffer 3/4 full (i.e., has 3 data characters) 0x = Interrupt is set when any character is received and transferred from the RSR to the receive buffer. Receive buffer has one or more characters. Note 1: Value of bit only affects the transmit properties of the module when the IrDA® encoder is enabled (IREN=1). 2: If UARTEN = 1, the peripheral inputs and outputs must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information. DS39905E-page 198  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 17-2: UxSTA: UARTx STATUS AND CONTROL REGISTER (CONTINUED) bit 5 ADDEN: Address Character Detect bit (bit 8 of received data=1) 1 = Address Detect mode enabled. If 9-bit mode is not selected, this does not take effect. 0 = Address Detect mode disabled bit 4 RIDLE: Receiver Idle bit (read-only) 1 = Receiver is Idle 0 = Receiver is active bit 3 PERR: Parity Error Status bit (read-only) 1 = Parity error has been detected for the current character (character at the top of the receive FIFO) 0 = Parity error has not been detected bit 2 FERR: Framing Error Status bit (read-only) 1 = Framing error has been detected for the current character (character at the top of the receive FIFO) 0 = Framing error has not been detected bit 1 OERR: Receive Buffer Overrun Error Status bit (clear/read-only) 1 = Receive buffer has overflowed 0 = Receive buffer has not overflowed (clearing a previously set OERR bit (10 transition) will reset the receiver buffer and the RSR to the empty state) bit 0 URXDA: Receive Buffer Data Available bit (read-only) 1 = Receive buffer has data; at least one more character can be read 0 = Receive buffer is empty Note 1: Value of bit only affects the transmit properties of the module when the IrDA® encoder is enabled (IREN=1). 2: If UARTEN = 1, the peripheral inputs and outputs must be configured to an available RPn pin. See Section10.4 “Peripheral Pin Select” for more information.  2010 Microchip Technology Inc. DS39905E-page 199

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 200  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 18.0 PARALLEL MASTER PORT Key features of the PMP module include: (PMP) • Up to 16 Programmable Address Lines • Up to 2 Chip Select Lines Note: This data sheet summarizes the features of • Programmable Strobe Options: this group of PIC24F devices. It is not - Individual Read and Write Strobes or; intended to be a comprehensive reference source. For more information, refer to the - Read/Write Strobe with Enable Strobe “PIC24F Family Reference Manual”, • Address Auto-Increment/Auto-Decrement Section 13. “Parallel Master Port (PMP)” • Programmable Address/Data Multiplexing (DS39713). • Programmable Polarity on Control Signals The Parallel Master Port (PMP) module is a parallel, • Legacy Parallel Slave Port Support 8-bit I/O module, specifically designed to communicate • Enhanced Parallel Slave Support: with a wide variety of parallel devices, such as commu- - Address Support nication peripherals, LCDs, external memory devices - 4-Byte Deep Auto-Incrementing Buffer and microcontrollers. Because the interface to parallel • Programmable Wait States peripherals varies significantly, the PMP is highly • Selectable Input Voltage Levels configurable. FIGURE 18-1: PMP MODULE OVERVIEW Address Bus Data Bus Control Lines PMA<0> PIC24F PMALL Parallel Master Port PMA<1> PMALH Up to 16-Bit Address PMA<13:2> EEPROM PMA<14> PMCS1 PMA<15> PMCS2 PMBE FIFO PMRD Microcontroller LCD Buffer PMRD/PMWR PMWR PMENB PMD<7:0> PMA<7:0> PMA<15:8> 8-Bit Data  2010 Microchip Technology Inc. DS39905E-page 201

PIC24FJ256GA110 FAMILY REGISTER 18-1: PMCON: PARALLEL MASTER PORT CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PMPEN — PSIDL ADRMUX1 ADRMUX0 PTBEEN PTWREN PTRDEN bit 15 bit 8 R/W-0 R/W-0 R/W-0(1) R/W-0(1) R/W-0(1) R/W-0 R/W-0 R/W-0 CSF1 CSF0 ALP CS2P CS1P BEP WRSP RDSP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 PMPEN: Parallel Master Port Enable bit 1 = PMP enabled 0 = PMP disabled, no off-chip access performed bit 14 Unimplemented: Read as ‘0’ bit 13 PSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-11 ADRMUX<1:0>: Address/Data Multiplexing Selection bits 11 = Reserved 10 = All 16 bits of address are multiplexed on PMD<7:0> pins 01 = Lower 8 bits of address are multiplexed on PMD<7:0> pins, upper 3 bits are multiplexed on PMA<10:8> 00 = Address and data appear on separate pins bit 10 PTBEEN: Byte Enable Port Enable bit (16-Bit Master mode) 1 = PMBE port enabled 0 = PMBE port disabled bit 9 PTWREN: Write Enable Strobe Port Enable bit 1 = PMWR/PMENB port enabled 0 = PMWR/PMENB port disabled bit 8 PTRDEN: Read/Write Strobe Port Enable bit 1 = PMRD/PMWR port enabled 0 = PMRD/PMWR port disabled bit 7-6 CSF<1:0>: Chip Select Function bits 11 = Reserved 10 = PMCS1 and PMCS2 function as chip select 01 = PMCS2 functions as chip select, PMCS1 functions as address bit 14 00 = PMCS1 and PMCS2 function as address bits 15 and 14 bit 5 ALP: Address Latch Polarity bit(1) 1 = Active-high (PMALL and PMALH) 0 = Active-low (PMALL and PMALH) bit 4 CS2P: Chip Select 2 Polarity bit(1) 1 = Active-high (PMCS2/PMCS2) 0 = Active-low (PMCS2/PMCS2) bit 3 CS1P: Chip Select 1 Polarity bit(1) 1 = Active-high (PMCS1/PMCS1) 0 = Active-low (PMCS1/PMCS1) Note 1: These bits have no effect when their corresponding pins are used as address lines. DS39905E-page 202  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 18-1: PMCON: PARALLEL MASTER PORT CONTROL REGISTER (CONTINUED) bit 2 BEP: Byte Enable Polarity bit 1 = Byte enable active-high (PMBE) 0 = Byte enable active-low (PMBE) bit 1 WRSP: Write Strobe Polarity bit For Slave Modes and Master Mode 2 (PMMODE<9:8>=00, 01, 10): 1 = Write strobe active-high (PMWR) 0 = Write strobe active-low (PMWR) For Master Mode 1 (PMMODE<9:8>=11): 1 = Enable strobe active-high (PMENB) 0 = Enable strobe active-low (PMENB) bit 0 RDSP: Read Strobe Polarity bit For Slave Modes and Master Mode 2 (PMMODE<9:8>=00, 01, 10): 1 = Read strobe active-high (PMRD) 0 = Read strobe active-low (PMRD) For Master Mode 1 (PMMODE<9:8>=11): 1 = Read/write strobe active-high (PMRD/PMWR) 0 = Read/write strobe active-low (PMRD/PMWR) Note 1: These bits have no effect when their corresponding pins are used as address lines.  2010 Microchip Technology Inc. DS39905E-page 203

PIC24FJ256GA110 FAMILY REGISTER 18-2: PMMODE: PARALLEL MASTER PORT MODE REGISTER R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BUSY IRQM1 IRQM0 INCM1 INCM0 MODE16 MODE1 MODE0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WAITB1(1) WAITB0(1) WAITM3 WAITM2 WAITM1 WAITM0 WAITE1(1) WAITE0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 BUSY: Busy bit (Master mode only) 1 = Port is busy (not useful when the processor stall is active) 0 = Port is not busy bit 14-13 IRQM<1:0>: Interrupt Request Mode bits 11 = Interrupt generated when Read Buffer 3 is read or Write Buffer 3 is written (Buffered PSP mode), or on a read or write operation when PMA<1:0> = 11 (Addressable PSP mode only) 10 = No interrupt generated, processor stall activated 01 = Interrupt generated at the end of the read/write cycle 00 = No interrupt generated bit 12-11 INCM<1:0>: Increment Mode bits 11 = PSP read and write buffers auto-increment (Legacy PSP mode only) 10 = Decrement ADDR<10:0> by 1 every read/write cycle 01 = Increment ADDR<10:0> by 1 every read/write cycle 00 = No increment or decrement of address bit 10 MODE16: 8/16-Bit Mode bit 1 = 16-bit mode: Data register is 16 bits; a read or write to the Data register invokes two 8-bit transfers 0 = 8-bit mode: Data register is 8 bits; a read or write to the Data register invokes one 8-bit transfer bit 9-8 MODE<1:0>: Parallel Port Mode Select bits 11 = Master Mode 1 (PMCS1, PMRD/PMWR, PMENB, PMBE, PMA<x:0> and PMD<7:0>) 10 = Master Mode 2 (PMCS1, PMRD, PMWR, PMBE, PMA<x:0> and PMD<7:0>) 01 = Enhanced PSP, control signals (PMRD, PMWR, PMCS1, PMD<7:0> and PMA<1:0>) 00 = Legacy Parallel Slave Port, control signals (PMRD, PMWR, PMCS1 and PMD<7:0>) bit 7-6 WAITB<1:0>: Data Setup to Read/Write Wait State Configuration bits(1) 11 = Data wait of 4 TCY; multiplexed address phase of 4 TCY 10 = Data wait of 3 TCY; multiplexed address phase of 3 TCY 01 = Data wait of 2 TCY; multiplexed address phase of 2 TCY 00 = Data wait of 1 TCY; multiplexed address phase of 1 TCY bit 5-2 WAITM<3:0>: Read to Byte Enable Strobe Wait State Configuration bits 1111 = Wait of additional 15 TCY ... 0001 = Wait of additional 1 TCY 0000 = No additional wait cycles (operation forced into one TCY)(2) bit 1-0 WAITE<1:0>: Data Hold After Strobe Wait State Configuration bits(1) 11 = Wait of 4 TCY 10 = Wait of 3 TCY 01 = Wait of 2 TCY 00 = Wait of 1 TCY Note 1: WAITB and WAITE bits are ignored whenever WAITM<3:0> = 0000. 2: A single cycle delay is required between consecutive read and/or write operations. DS39905E-page 204  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 18-3: PMADDR: PARALLEL MASTER PORT ADDRESS REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CS2 CS1 ADDR13 ADDR12 ADDR11 ADDR10 ADDR9 ADDR8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CS2: Chip Select 2 bit 1 = Chip Select 2 is active 0 = Chip Select 2 is inactive bit 14 CS1: Chip Select 1 bit 1 = Chip Select 1 is active 0 = Chip Select 1 is inactive bit 13-0 ADDR<13:0>: Parallel Port Destination Address bits REGISTER 18-4: PMAEN: PARALLEL MASTER PORT ENABLE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTEN15 PTEN14 PTEN13 PTEN12 PTEN11 PTEN10 PTEN9 PTEN8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTEN7 PTEN6 PTEN5 PTEN4 PTEN3 PTEN2 PTEN1 PTEN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 PTEN<15:14>: PMCSx Strobe Enable bits 1 = PMA15 and PMA14 function as either PMA<15:14> or PMCS2 and PMCS1 0 = PMA15 and PMA14 function as port I/O bit 13-2 PTEN<13:2>: PMP Address Port Enable bits 1 = PMA<13:2> function as PMP address lines 0 = PMA<13:2> function as port I/O bit 1-0 PTEN<1:0>: PMALH/PMALL Strobe Enable bits 1 = PMA1 and PMA0 function as either PMA<1:0> or PMALH and PMALL 0 = PMA1 and PMA0 pads functions as port I/O  2010 Microchip Technology Inc. DS39905E-page 205

PIC24FJ256GA110 FAMILY REGISTER 18-5: PMSTAT: PARALLEL MASTER PORT STATUS REGISTER R-0 R/W-0, HS U-0 U-0 R-0 R-0 R-0 R-0 IBF IBOV — — IB3F IB2F IB1F IB0F bit 15 bit 8 R-1 R/W-0, HS U-0 U-0 R-1 R-1 R-1 R-1 OBE OBUF — — OB3E OB2E OB1E OB0E bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 IBF: Input Buffer Full Status bit 1 = All writable input buffer registers are full 0 = Some or all of the writable input buffer registers are empty bit 14 IBOV: Input Buffer Overflow Status bit 1 = A write attempt to a full input byte register occurred (must be cleared in software) 0 = No overflow occurred bit 13-12 Unimplemented: Read as ‘0’ bit 11-8 IB3F:IB0F Input Buffer x Status Full bits 1 = Input buffer contains data that has not been read (reading buffer will clear this bit) 0 = Input buffer does not contain any unread data bit 7 OBE: Output Buffer Empty Status bit 1 = All readable output buffer registers are empty 0 = Some or all of the readable output buffer registers are full bit 6 OBUF: Output Buffer Underflow Status bit 1 = A read occurred from an empty output byte register (must be cleared in software) 0 = No underflow occurred bit 5-4 Unimplemented: Read as ‘0’ bit 3-0 OB3E:OB0E Output Buffer x Status Empty bits 1 = Output buffer is empty (writing data to the buffer will clear this bit) 0 = Output buffer contains data that has not been transmitted DS39905E-page 206  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 18-6: PADCFG1: PAD CONFIGURATION CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — RTSECSEL(1) PMPTTL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-2 Unimplemented: Read as ‘0’ bit 1 RTSECSEL: RTCC Seconds Clock Output Select bit(1) 1 = RTCC seconds clock is selected for the RTCC pin 0 = RTCC alarm pulse is selected for the RTCC pin bit 0 PMPTTL: PMP Module TTL Input Buffer Select bit 1 = PMP module inputs (PMDx, PMCS1) use TTL input buffers 0 = PMP module inputs use Schmitt Trigger input buffers Note 1: To enable the actual RTCC output, the RTCOE (RCFGCAL<10>) bit must also be set.  2010 Microchip Technology Inc. DS39905E-page 207

PIC24FJ256GA110 FAMILY FIGURE 18-2: LEGACY PARALLEL SLAVE PORT EXAMPLE Address Bus Master PIC24F Slave Data Bus PMD<7:0> PMD<7:0> Control Lines PMCS1 PMCS1 PMRD PMRD PMWR PMWR FIGURE 18-3: ADDRESSABLE PARALLEL SLAVE PORT EXAMPLE Master PIC24F Slave PMA<1:0> PMA<1:0> PMD<7:0> Write Read PMD<7:0> Address Address Decode Decode PMDOUT1L (0) PMDIN1L (0) PMCS1 PMCS1 PMDOUT1H (1) PMDIN1H (1) PMRD PMRD PMDOUT2L (2) PMDIN2L (2) PMWR PMWR PMDOUT2H (3) PMDIN2H (3) Address Bus Data Bus Control Lines TABLE 18-1: SLAVE MODE ADDRESS RESOLUTION PMA<1:0> Output Register (Buffer) Input Register (Buffer) 00 PMDOUT1<7:0> (0) PMDIN1<7:0> (0) 01 PMDOUT1<15:8> (1) PMDIN1<15:8> (1) 10 PMDOUT2<7:0> (2) PMDIN2<7:0> (2) 11 PMDOUT2<15:8> (3) PMDIN2<15:8> (3) FIGURE 18-4: MASTER MODE, DEMULTIPLEXED ADDRESSING (SEPARATE READ AND WRITE STROBES, TWO CHIP SELECTS) PIC24F PMA<13:0> PMD<7:0> PMCS1 PMCS2 Address Bus PMRD Data Bus PMWR Control Lines DS39905E-page 208  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 18-5: MASTER MODE, PARTIALLY MULTIPLEXED ADDRESSING (SEPARATE READ AND WRITE STROBES, TWO CHIP SELECTS) PIC24F PMA<13:8> PMD<7:0> PMA<7:0> PMCS1 PMCS2 Address Bus Multiplexed PMALL Data and PMRD Address Bus Control Lines PMWR FIGURE 18-6: MASTER MODE, FULLY MULTIPLEXED ADDRESSING (SEPARATE READ AND WRITE STROBES, TWO CHIP SELECTS) PMD<7:0> PIC24F PMA<13:8> PMCS1 PMCS2 PMALL PMALH Multiplexed Data and PMRD Address Bus PMWR Control Lines FIGURE 18-7: EXAMPLE OF A MULTIPLEXED ADDRESSING APPLICATION PIC24F A<7:0> PMD<7:0> 373 A<15:0> PMALL D<7:0> D<7:0> CE A<15:8> 373 OE WR PMALH PMCS1 Address Bus PMRD Data Bus PMWR Control Lines  2010 Microchip Technology Inc. DS39905E-page 209

PIC24FJ256GA110 FAMILY FIGURE 18-8: EXAMPLE OF A PARTIALLY MULTIPLEXED ADDRESSING APPLICATION PIC24F A<7:0> PMD<7:0> 373 A<10:0> PMALL D<7:0> D<7:0> A<10:8> PMA<10:8> CE PMCS1 OE WR Address Bus Data Bus PMRD Control Lines PMWR FIGURE 18-9: EXAMPLE OF AN 8-BIT MULTIPLEXED ADDRESS AND DATA APPLICATION PIC24F Parallel Peripheral PMD<7:0> AD<7:0> PMALL ALE PMCS1 CS Address Bus PMRD RD Data Bus PMWR WR Control Lines FIGURE 18-10: PARALLEL EEPROM EXAMPLE (UP TO 15-BIT ADDRESS, 8-BIT DATA) PIC24F Parallel EEPROM PMA<n:0> A<n:0> PMD<7:0> D<7:0> PMCS1 CE Address Bus PMRD OE Data Bus PMWR WR Control Lines FIGURE 18-11: PARALLEL EEPROM EXAMPLE (UP TO 15-BIT ADDRESS, 16-BIT DATA) PIC24F Parallel EEPROM PMA<n:0> A<n:1> PMD<7:0> D<7:0> PMBE A0 PMCS1 CE Address Bus PMRD OE Data Bus PMWR WR Control Lines FIGURE 18-12: LCD CONTROL EXAMPLE (BYTE MODE OPERATION) PIC24F LCD Controller PM<7:0> D<7:0> PMA0 RS Address Bus PMRD/PMWR R/W Data Bus PMCS1 E Control Lines DS39905E-page 210  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 19.0 REAL-TIME CLOCK AND Key features include: CALENDAR (RTCC) • Time data in hours, minutes and seconds, with a granularity of one-half second Note: This data sheet summarizes the features of • 24-hour format (military time) display option this group of PIC24F devices. It is not • Calendar data as date, month and year intended to be a comprehensive reference • Automatic, hardware-based day of week and leap source. For more information, refer to the year calculations for dates from 2000 through “PIC24F Family Reference Manual”, 2099 Section 29. “Real-Time Clock and Calendar (RTCC)” (DS39696). • Time and calendar data in BCD format for compact firmware The Real-Time Clock and Calendar (RTCC) provides • Highly configurable alarm function on-chip, hardware-based clock and calendar function- • External output pin with selectable alarm signal or ality with little or no CPU overhead. It is intended for seconds “tick” signal output applications where accurate time must be maintained • User calibration feature with auto-adjust for extended periods with minimal CPU activity and with limited power resources, such as battery-powered A simplified block diagram of the module is shown in applications. Figure19-1.The SOSC and RTCC will both remain running while the device is held in Reset with MCLR and will continue running after MCLR is released. FIGURE 19-1: RTCC BLOCK DIAGRAM RTCC Clock Domain CPU Clock Domain 32.768 kHz Input RCFGCAL from SOSC Oscillator RTCC Prescalers ALCFGRPT YEAR 0.5s MTHDY RTCC Timer RTCVAL WKDYHR Alarm Event MINSEC Comparator ALMTHDY Compare Registers ALRMVAL ALWDHR with Masks ALMINSEC Repeat Counter RTCC Interrupt RTCC Interrupt Logic Alarm Pulse RTCC Pin RTCOE  2010 Microchip Technology Inc. DS39905E-page 211

PIC24FJ256GA110 FAMILY 19.1 RTCC Module Registers TABLE 19-2: ALRMVAL REGISTER MAPPING The RTCC module registers are organized into three categories: ALRMPTR Alarm Value Register Window • RTCC Control Registers <1:0> ALRMVAL<15:8> ALRMVAL<7:0> • RTCC Value Registers 00 ALRMMIN ALRMSEC • Alarm Value Registers 01 ALRMWD ALRMHR 19.1.1 REGISTER MAPPING 10 ALRMMNTH ALRMDAY To limit the register interface, the RTCC Timer and 11 — — Alarm Time registers are accessed through corre- sponding register pointers. The RTCC Value register Considering that the 16-bit core does not distinguish window (RTCVALH and RTCVALL) uses the RTCPTR between 8-bit and 16-bit read operations, the user must bits (RCFGCAL<9:8>) to select the desired Timer be aware that when reading either the ALRMVALH or register pair (see Table19-1). ALRMVALL bytes will decrement the ALRMPTR<1:0> value. The same applies to the RTCVALH or RTCVALL By writing to the RTCVALH byte, the RTCC Pointer bytes with the RTCPTR<1:0> being decremented. value, RTCPTR<1:0> bits, decrement by one until they reach ‘00’. Once they reach ‘00’, the MINUTES and Note: This only applies to read operations and SECONDS value will be accessible through RTCVALH not write operations. and RTCVALL until the pointer value is manually changed. 19.1.2 WRITE LOCK In order to perform a write to any of the RTCC Timer TABLE 19-1: RTCVAL REGISTER MAPPING registers, the RTCWREN bit (RCFGCAL<13>) must be RTCC Value Register Window set (refer to Example19-1). RTCPTR <1:0> Note: To avoid accidental writes to the timer, it is RTCVAL<15:8> RTCVAL<7:0> recommended that the RTCWREN bit 00 MINUTES SECONDS (RCFGCAL<13>) is kept clear at any 01 WEEKDAY HOURS other time. For the RTCWREN bit to be set, there is only 1 instruction cycle time 10 MONTH DAY window allowed between the unlock 11 — YEAR sequence and the setting of RTCWREN; therefore, it is recommended that code The Alarm Value register window (ALRMVALH and follow the procedure in Example19-1. ALRMVALL) uses the ALRMPTR bits For applications written in C, the unlock (ALCFGRPT<9:8>) to select the desired Alarm register sequence should be implemented using pair (see Table19-2). in-line assembly. By writing to the ALRMVALH byte, the Alarm Pointer value, ALRMPTR<1:0> bits, decrement by one until they reach ‘00’. Once they reach ‘00’, the ALRMMIN EXAMPLE 19-1: SETTING THE RTCWREN and ALRMSEC value will be accessible through BIT ALRMVALH and ALRMVALL until the pointer value is asm volatile("disi #5"); manually changed. __builtin_write_RTCWEN(); DS39905E-page 212  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 19.1.3 RTCC CONTROL REGISTERS REGISTER 19-1: RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER(1) R/W-x U-x R/W-x R-x R-x R/W-x R/W-x R/W-x RTCEN(2) — RTCWREN RTCSYNC HALFSEC(3) RTCOE RTCPTR1 RTCPTR0 bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x CAL7 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 RTCEN: RTCC Enable bit(2) 1 = RTCC module is enabled 0 = RTCC module is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 RTCWREN: RTCC Value Registers Write Enable bit 1 = RTCVALH and RTCVALL registers can be written to by the user 0 = RTCVALH and RTCVALL registers are locked out from being written to by the user bit 12 RTCSYNC: RTCC Value Registers Read Synchronization bit 1 = RTCVALH, RTCVALL and ALCFGRPT registers can change while reading due to a rollover ripple resulting in an invalid data read. If the register is read twice and results in the same data, the data can be assumed to be valid. 0 = RTCVALH, RTCVALL or ALCFGRPT registers can be read without concern over a rollover ripple bit 11 HALFSEC: Half-Second Status bit(3) 1 = Second half period of a second 0 = First half period of a second bit 10 RTCOE: RTCC Output Enable bit 1 = RTCC output enabled 0 = RTCC output disabled bit 9-8 RTCPTR<1:0>: RTCC Value Register Window Pointer bits Points to the corresponding RTCC Value registers when reading the RTCVALH and RTCVALL registers; the RTCPTR<1:0> value decrements on every read or write of RTCVALH until it reaches ‘00’. RTCVAL<15:8>: 00 =MINUTES 01 =WEEKDAY 10 =MONTH 11 =Reserved RTCVAL<7:0>: 00 = SECONDS 01 = HOURS 10 = DAY 11 = YEAR Note 1: The RCFGCAL register is only affected by a POR. 2: A write to the RTCEN bit is only allowed when RTCWREN=1. 3: This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register.  2010 Microchip Technology Inc. DS39905E-page 213

PIC24FJ256GA110 FAMILY REGISTER 19-1: RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER(1) (CONTINUED) bit 7-0 CAL<7:0>: RTC Drift Calibration bits 01111111 = Maximum positive adjustment; adds 508 RTC clock pulses every one minute ... 00000001 = Minimum positive adjustment; adds 4 RTC clock pulses every one minute 00000000 = No adjustment 11111111 = Minimum negative adjustment; subtracts 4 RTC clock pulses every one minute ... 10000000 = Maximum negative adjustment; subtracts 512 RTC clock pulses every one minute Note 1: The RCFGCAL register is only affected by a POR. 2: A write to the RTCEN bit is only allowed when RTCWREN=1. 3: This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register. REGISTER 19-2: PADCFG1: PAD CONFIGURATION CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — RTSECSEL(1) PMPTTL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-2 Unimplemented: Read as ‘0’ bit 1 RTSECSEL: RTCC Seconds Clock Output Select bit(1) 1 = RTCC seconds clock is selected for the RTCC pin 0 = RTCC alarm pulse is selected for the RTCC pin bit 0 PMPTTL: PMP Module TTL Input Buffer Select bit 1 = PMP module inputs (PMDx, PMCS1) use TTL input buffers 0 = PMP module inputs use Schmitt Trigger input buffers Note 1: To enable the actual RTCC output, the RTCOE (RCFGCAL<10>) bit must also be set. DS39905E-page 214  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 19-3: ALCFGRPT: ALARM CONFIGURATION REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ALRMEN CHIME AMASK3 AMASK2 AMASK1 AMASK0 ALRMPTR1 ALRMPTR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ARPT7 ARPT6 ARPT5 ARPT4 ARPT3 ARPT2 ARPT1 ARPT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ALRMEN: Alarm Enable bit 1 = Alarm is enabled (cleared automatically after an alarm event whenever ARPT<7:0>=00h and CHIME=0) 0 = Alarm is disabled bit 14 CHIME: Chime Enable bit 1 = Chime is enabled; ARPT<7:0> bits are allowed to roll over from 00h to FFh 0 = Chime is disabled; ARPT<7:0> bits stop once they reach 00h bit 13-10 AMASK<3:0>: Alarm Mask Configuration bits 0000 = Every half second 0001 = Every second 0010 = Every 10 seconds 0011 = Every minute 0100 = Every 10 minutes 0101 = Every hour 0110 = Once a day 0111 = Once a week 1000 = Once a month 1001 = Once a year (except when configured for February 29th, once every 4 years) 101x = Reserved; do not use 11xx = Reserved; do not use bit 9-8 ALRMPTR<1:0>: Alarm Value Register Window Pointer bits Points to the corresponding Alarm Value registers when reading ALRMVALH and ALRMVALL registers; the ALRMPTR<1:0> value decrements on every read or write of ALRMVALH until it reaches ‘00’. ALRMVAL<15:8>: 00 = ALRMMIN 01 = ALRMWD 10 = ALRMMNTH 11 = Unimplemented ALRMVAL<7:0>: 00 = ALRMSEC 01 = ALRMHR 10 = ALRMDAY 11 = Unimplemented bit 7-0 ARPT<7:0>: Alarm Repeat Counter Value bits 11111111 = Alarm will repeat 255 more times ... 00000000 = Alarm will not repeat The counter decrements on any alarm event. The counter is prevented from rolling over from 00h to FFh unless CHIME=1.  2010 Microchip Technology Inc. DS39905E-page 215

PIC24FJ256GA110 FAMILY 19.1.4 RTCVAL REGISTER MAPPINGS REGISTER 19-4: YEAR: YEAR VALUE REGISTER(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x YRTEN3 YRTEN2 YRTEN1 YRTEN0 YRONE3 YRONE2 YRONE1 YRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-4 YRTEN<3:0>: Binary Coded Decimal Value of Year’s Tens Digit bits Contains a value from 0 to 9. bit 3-0 YRONE<3:0>: Binary Coded Decimal Value of Year’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to the YEAR register is only allowed when RTCWREN=1. REGISTER 19-5: MTHDY: MONTH AND DAY VALUE REGISTER(1) U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x — — — MTHTEN0 MTHONE3 MTHONE2 MTHONE1 MTHONE0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — DAYTEN1 DAYTEN0 DAYONE3 DAYONE2 DAYONE1 DAYONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit Contains a value of 0 or 1. bit 11-8 MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits Contains a value from 0 to 9. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits Contains a value from 0 to 3. bit 3-0 DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1. DS39905E-page 216  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 19-6: WKDYHR: WEEKDAY AND HOURS VALUE REGISTER(1) U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x — — — — — WDAY2 WDAY1 WDAY0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — HRTEN1 HRTEN0 HRONE3 HRONE2 HRONE1 HRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits Contains a value from 0 to 6. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits Contains a value from 0 to 2. bit 3-0 HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1. REGISTER 19-7: MINSEC: MINUTES AND SECONDS VALUE REGISTER U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — MINTEN2 MINTEN1 MINTEN0 MINONE3 MINONE2 MINONE1 MINONE0 bit 15 bit 8 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — SECTEN2 SECTEN1 SECTEN0 SECONE3 SECONE2 SECONE1 SECONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits Contains a value from 0 to 5. bit 11-8 MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits Contains a value from 0 to 9. bit 7 Unimplemented: Read as ‘0’ bit 6-4 SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits Contains a value from 0 to 9.  2010 Microchip Technology Inc. DS39905E-page 217

PIC24FJ256GA110 FAMILY 19.1.5 ALRMVAL REGISTER MAPPINGS REGISTER 19-8: ALMTHDY: ALARM MONTH AND DAY VALUE REGISTER(1) U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x — — — MTHTEN0 MTHONE3 MTHONE2 MTHONE1 MTHONE0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — DAYTEN1 DAYTEN0 DAYONE3 DAYONE2 DAYONE1 DAYONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit Contains a value of 0 or 1. bit 11-8 MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits Contains a value from 0 to 9. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits Contains a value from 0 to 3. bit 3-0 DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1. REGISTER 19-9: ALWDHR: ALARM WEEKDAY AND HOURS VALUE REGISTER(1) U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x — — — — — WDAY2 WDAY1 WDAY0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — HRTEN1 HRTEN0 HRONE3 HRONE2 HRONE1 HRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits Contains a value from 0 to 6. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits Contains a value from 0 to 2. bit 3-0 HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1. DS39905E-page 218  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 19-10: ALMINSEC: ALARM MINUTES AND SECONDS VALUE REGISTER U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — MINTEN2 MINTEN1 MINTEN0 MINONE3 MINONE2 MINONE1 MINONE0 bit 15 bit 8 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — SECTEN2 SECTEN1 SECTEN0 SECONE3 SECONE2 SECONE1 SECONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits Contains a value from 0 to 5. bit 11-8 MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits Contains a value from 0 to 9. bit 7 Unimplemented: Read as ‘0’ bit 6-4 SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits Contains a value from 0 to 9. 19.2 Calibration 3. a) If the oscillator is faster then ideal (negative result form Step 2), the RCFGCAL register value The real-time crystal input can be calibrated using the needs to be negative. This causes the specified periodic auto-adjust feature. When properly calibrated, number of clock pulses to be subtracted from the RTCC can provide an error of less than 3 seconds the timer counter once every minute. per month. This is accomplished by finding the number b) If the oscillator is slower then ideal (positive of error clock pulses for one minute and storing the result from Step 2) the RCFGCAL register value value into the lower half of the RCFGCAL register. The needs to be positive. This causes the specified 8-bit signed value loaded into the lower half of number of clock pulses to be added from the RCFGCAL is multiplied by four and will be either added timer counter once every minute. or subtracted from the RTCC timer, once every minute. Refer to the steps below for RTCC calibration: 4. Divide the number of error clocks per minute by 4 to get the correct CAL value and load the 1. Using another timer resource on the device, the RCFGCAL register with the correct value. user must find the error of the 32.768kHz crystal. (Each 1-bit increment in CAL adds or subtracts 2. Once the error is known, it must be converted to 4 pulses.) the number of error clock pulses per minute and Writes to the lower half of the RCFGCAL register loaded into the RCFGCAL register. should only occur when the timer is turned off, or immediately after the rising edge of the seconds pulse. EQUATION 19-1: RTCC CALIBRATION Note: It is up to the user to include in the error Error (Clocks per Minute) = (Ideal Frequency† – value the initial error of the crystal, drift Measured Frequency) * 60 = Clocks per Minute due to temperature and drift due to crystal † Ideal frequency = 32,768 Hz aging.  2010 Microchip Technology Inc. DS39905E-page 219

PIC24FJ256GA110 FAMILY 19.3 Alarm After each alarm is issued, the value of the ARPT bits is decremented by one. Once the value has reached • Configurable from half second to one year 00h, the alarm will be issued one last time, after which • Enabled using the ALRMEN bit the ALRMEN bit will be cleared automatically and the (ALCFGRPT<15>, Register19-3) alarm will turn off. • One-time alarm and repeat alarm options Indefinite repetition of the alarm can occur if the CHIME available bit = 1. Instead of the alarm being disabled when the value of the ARPT bits reaches 00h, it rolls over to FFh 19.3.1 CONFIGURING THE ALARM and continues counting indefinitely while CHIME is set. The alarm feature is enabled using the ALRMEN bit. This bit is cleared when an alarm is issued. Writes to 19.3.2 ALARM INTERRUPT ALRMVAL should only take place when ALRMEN=0. At every alarm event, an interrupt is generated. In As shown in Figure19-2, the interval selection of the addition, an alarm pulse output is provided that alarm is configured through the AMASK bits operates at half the frequency of the alarm. This output (ALCFGRPT<13:10>). These bits determine which and is completely synchronous to the RTCC clock and can how many digits of the alarm must match the clock be used as a trigger clock to other peripherals. value for the alarm to occur. The alarm can also be configured to repeat based on a Note: Changing any of the registers, other then preconfigured interval. The amount of times this occurs the RCFGCAL and ALCFGRPT registers, once the alarm is enabled is stored in the ARPT bits, and the CHIME bit while the alarm is ARPT<7:0> (ALCFGRPT<7:0>). When the value of the enabled (ALRMEN = 1), can result in a ARPT bits equals 00h and the CHIME bit false alarm event leading to a false alarm (ALCFGRPT<14>) is cleared, the repeat function is interrupt. To avoid a false alarm event, the disabled and only a single alarm will occur. The alarm timer and alarm values should only be can be repeated up to 255 times by loading changed while the alarm is disabled ARPT<7:0> with FFh. (ALRMEN = 0). It is recommended that the ALCFGRPT register and CHIME bit be changed when RTCSYNC = 0. FIGURE 19-2: ALARM MASK SETTINGS Day of Alarm Mask Setting the (AMASK<3:0>) Week Month Day Hours Minutes Seconds 0000 – Every half second 0001 – Every second 0010 – Every 10 seconds s 0011 – Every minute s s 0100 – Every 10 minutes m s s 0101 – Every hour m m s s 0110 – Every day h h m m s s 0111 – Every week d h h m m s s 1000 – Every month d d h h m m s s 1001 – Every year(1) m m d d h h m m s s Note 1: Annually, except when configured for February 29. DS39905E-page 220  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 20.0 PROGRAMMABLE CYCLIC Consider the CRC equation: REDUNDANCY CHECK (CRC) x16 + x12 + x5 + 1 GENERATOR To program this polynomial into the CRC generator, the CRC register bits should be set as shown in Note: This data sheet summarizes the features of Table20-1. this group of PIC24F devices. It is not intended to be a comprehensive reference TABLE 20-1: EXAMPLE CRC SETUP source. For more information, refer to the “PIC24F Family Reference Manual”, Bit Name Bit Value Section 30. “Programmable Cyclic PLEN<3:0> 1111 Redundancy Check (CRC)” (DS39714). X<15:1> 000100000010000 The programmable CRC generator offers the following Note that for the value of X<15:1>, the 12th bit and the features: 5th bit are set to ‘1’, as required by the equation. The • User-programmable polynomial CRC equation 0bit required by the equation is always XORed. For a • Interrupt output 16-bit polynomial, the 16th bit is also always assumed to be XORed; therefore, the X<15:1> bits do not have • Data FIFO the 0 bit or the 16th bit. The module implements a software configurable CRC A simplified block diagram of the module is shown in generator. The terms of the polynomial and its length Figure20-1. The general topology of the shift engine is can be programmed using the X<15:1> bits shown in Figure20-2. (CRCXOR<15:1>) and the PLEN<3:0> bits (CRCCON<3:0>), respectively. FIGURE 20-1: CRC BLOCK DIAGRAM CRCDAT Variable FIFO FIFO Empty Event Set CRCIF (8x16 or 16x8) Shift Clock (2 FCY) CRC Shift Engine CRCWDAT  2010 Microchip Technology Inc. DS39905E-page 221

PIC24FJ256GA110 FAMILY FIGURE 20-2: CRC SHIFT ENGINE DETAIL CRCWDAT Read/Write Bus X(1)(1) X(2)(1) X(n)(1) Shift Buffer Data Bit 0 Bit 1 Bit 2 Bit n(2) Note 1: Each XOR stage of the shift engine is programmable. See text for details. 2: Polynomial length n is determined by ([PLEN<3:0>] + 1). 20.1 User Interface To empty words already written into a FIFO, the CRCGO bit must be set to ‘1’ and the CRC shifter 20.1.1 DATA INTERFACE allowed to run until the CRCMPT bit is set. To start serial shifting, a ‘1’ must be written to the Also, to get the correct CRC reading, it will be CRCGO bit. necessary to wait for the CRCMPT bit to go high before reading the CRCWDAT register. The module incorporates a FIFO that is 8 deep when PLEN<3:0> (CRCCON<3:0>)>7 and 16 deep, other- If a word is written when the CRCFUL bit is set, the wise. The data for which the CRC is to be calculated VWORD Pointer will roll over to 0. The hardware will must first be written into the FIFO. The smallest data then behave as if the FIFO is empty. However, the con- element that can be written into the FIFO is one byte. dition to generate an interrupt will not be met; therefore, For example, if PLEN=5, then the size of the data is no interrupt will be generated (See Section20.1.2 PLEN+1=6. When loading data, the two MSbs of the “Interrupt Operation”). data byte are ignored. At least one instruction cycle must pass after a write to Once data is written into the CRCWDAT MSb (as CRCWDAT before a read of the VWORD bits is done. defined by PLEN), the value of VWORD<4:0> 20.1.2 INTERRUPT OPERATION (CRCCON<12:8>) increments by one. When CRCGO=1 and VWORD>0, a word of data to be When the VWORD<4:0> bits make a transition from a shifted is moved from the FIFO into the shift engine. value of ‘1’ to ‘0’, an interrupt will be generated. Note When the data word moves from the FIFO to the shift that the CRC calculation is not complete at this point; engine, the VWORD bits decrement by one. The serial an additional time of (PLEN + 1)/2 clock cycles is shifter continues to receive data from the FIFO, shifting required before the output can be read. until the VWORD bits reach 0. The last bit of data will be shifted through the CRC module (PLEN + 1)/2 clock 20.2 Operation in Power Save Modes cycles after the VWORD bits reach 0. This is when the module is completed with the CRC calculation. 20.2.1 SLEEP MODE Therefore, for a given value of PLEN, it will take If Sleep mode is entered while the module is operating, (PLEN+1)/2*VWORD number of clock cycles to the module will be suspended in its current state until complete the CRC calculations. clock execution resumes. When VWORD<4:0> reach 8 (or 16), the CRCFUL bit will be set. When VWORD<4:0> reach 0, the CRCMPT 20.2.2 IDLE MODE bit will be set. To continue full module operation in Idle mode, the To continually feed data into the CRC engine, the CSIDL bit must be cleared prior to entry into the mode. recommended mode of operation is to initially “prime” If CSIDL=1, the module will behave the same way as the FIFO with a sufficient number of words so no inter- it does in Sleep mode; pending interrupt events will be rupt is generated before the next word can be written. passed on, even though the module clocks are not Once that is done, start the CRC by setting the CRCGO available. bit to ‘1’. From that point onward, the VWORD bits should be polled. If they read less than 8 or 16, another word can be written into the FIFO. DS39905E-page 222  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 20.3 Registers There are four registers used to control programmable CRC operation: • CRCCON • CRCXOR • CRCDAT • CRCWDAT REGISTER 20-1: CRCCON: CRC CONTROL REGISTER U-0 U-0 R/W-0 R-0 R-0 R-0 R-0 R-0 — — CSIDL VWORD4 VWORD3 VWORD2 VWORD1 VWORD0 bit 15 bit 8 R-0 R-1 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CRCFUL CRCMPT — CRCGO PLEN3 PLEN2 PLEN1 PLEN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 CSIDL: CRC Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-8 VWORD<4:0>: Pointer Value bits Indicates the number of valid words in the FIFO. Has a maximum value of 8 when PLEN<3:0> > 7 or 16 when PLEN<3:0> 7. bit 7 CRCFUL: FIFO Full bit 1 = FIFO is full 0 = FIFO is not full bit 6 CRCMPT: FIFO Empty Bit 1 = FIFO is empty 0 = FIFO is not empty bit 5 Unimplemented: Read as ‘0’ bit 4 CRCGO: Start CRC bit 1 = Start CRC serial shifter 0 = CRC serial shifter turned off bit 3-0 PLEN<3:0>: Polynomial Length bits Denotes the length of the polynomial to be generated minus 1.  2010 Microchip Technology Inc. DS39905E-page 223

PIC24FJ256GA110 FAMILY REGISTER 20-2: CRCXOR: CRC XOR POLYNOMIAL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 X15 X14 X13 X12 X11 X10 X9 X8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 X7 X6 X5 X4 X3 X2 X1 — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-1 X<15:1>: XOR of Polynomial Term Xn Enable bits bit 0 Unimplemented: Read as ‘0’ DS39905E-page 224  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 21.0 10-BIT HIGH-SPEED A/D A block diagram of the A/D Converter is shown in CONVERTER Figure21-1. To perform an A/D conversion: Note: This data sheet summarizes the features of 1. Configure the A/D module: this group of PIC24F devices. It is not a) Configure port pins as analog inputs and/or intended to be a comprehensive reference select band gap reference input source. For more information, refer to the (AD1PCFGL<15:0> and AD1PCFGH<1:0>). “PIC24F Family Reference Manual”, Section 17. “10-Bit A/D Converter” b) Select voltage reference source to match (DS39705). expected range on analog inputs (AD1CON2<15:13>). The 10-bit A/D Converter has the following key c) Select the analog conversion clock to match features: the desired data rate with the processor • Successive Approximation (SAR) Conversion clock (AD1CON3<7:0>). • Conversion Speeds of up to 500ksps d) Select the appropriate sample/conversion • 16 Analog Input pins sequence (AD1CON1<7:5> and AD1CON3<12:8>). • External Voltage Reference Input pins e) Select how conversion results are • Internal Band Gap Reference Inputs presented in the buffer (AD1CON1<9:8>). • Automatic Channel Scan mode f) Select interrupt rate (AD1CON2<5:2>). • Selectable Conversion Trigger Source g) Turn on A/D module (AD1CON1<15>). • 16-Word Conversion Result Buffer 2. Configure the A/D interrupt (if required): • Selectable Buffer Fill modes a) Clear the AD1IF bit. • Four Result Alignment Options b) Select A/D interrupt priority. • Operation during CPU Sleep and Idle modes On all PIC24FJ256GA110 family devices, the 10-bit A/D Converter has 16 analog input pins, designated AN0 through AN15. In addition, there are two analog input pins for external voltage reference connections (VREF+ and VREF-). These voltage reference inputs may be shared with other analog input pins.  2010 Microchip Technology Inc. DS39905E-page 225

PIC24FJ256GA110 FAMILY FIGURE 21-1: 10-BIT HIGH-SPEED A/D CONVERTER BLOCK DIAGRAM Internal Data Bus AVDD VR+ AVSS ct e 16 el VREF+ SR VR- V VREF- Comparator VINH VR- VR+ AN0 S/H DAC VINL AN1 AN2 10-Bit SAR Conversion Logic VINH AN3 AN4 A X Data Formatting AN5 U M AN6 AN7 VINL ADC1BUF0: ADC1BUFF AN8 AD1CON1 AN9 AD1CON2 AN10 AD1CON3 AD1CHS AN11 VINH AD1PCFGL B AN12 X AD1PCFGH U M AD1CSSL AN13 VINL AN14 AN15 VBG Sample Control Control Logic Conversion Control VBG/2 Input MUX Control Pin Config Control DS39905E-page 226  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 21-1: AD1CON1: A/D CONTROL REGISTER 1 R/W-0 U-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 ADON(1) — ADSIDL — — — FORM1 FORM0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0, HCS R-0, HCS SSRC2 SSRC1 SSRC0 — — ASAM SAMP DONE bit 7 bit 0 Legend: HCS = Hardware Clearable/Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ADON: A/D Operating Mode bit(1) 1 = A/D Converter module is operating 0 = A/D Converter is off bit 14 Unimplemented: Read as ‘0’ bit 13 ADSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-10 Unimplemented: Read as ‘0’ bit 9-8 FORM<1:0>: Data Output Format bits 11 = Signed fractional (sddd dddd dd00 0000) 10 = Fractional (dddd dddd dd00 0000) 01 = Signed integer (ssss sssd dddd dddd) 00 = Integer (0000 00dd dddd dddd) bit 7-5 SSRC<2:0>: Conversion Trigger Source Select bits 111 = Internal counter ends sampling and starts conversion (auto-convert) 110 = CTMU event ends sampling and starts conversion 101 = Reserved 100 = Timer5 compare ends sampling and starts conversion 011 = Reserved 010 = Timer3 compare ends sampling and starts conversion 001 = Active transition on INT0 pin ends sampling and starts conversion 000 = Clearing SAMP bit ends sampling and starts conversion bit 4-3 Unimplemented: Read as ‘0’ bit 2 ASAM: A/D Sample Auto-Start bit 1 = Sampling begins immediately after last conversion completes; SAMP bit is auto-set 0 = Sampling begins when the SAMP bit is set bit 1 SAMP: A/D Sample Enable bit 1 = A/D sample/hold amplifier is sampling input 0 = A/D sample/hold amplifier is holding bit 0 DONE: A/D Conversion Status bit 1 = A/D conversion is done 0 = A/D conversion is NOT done Note 1: Values of ADC1BUFx registers will not retain their values once the ADON bit is cleared. Read out the conversion values from the buffer before disabling the module.  2010 Microchip Technology Inc. DS39905E-page 227

PIC24FJ256GA110 FAMILY REGISTER 21-2: AD1CON2: A/D CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 r-0 U-0 R/W-0 U-0 U-0 VCFG2 VCFG1 VCFG0 r — CSCNA — — bit 15 bit 8 R-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BUFS — SMPI3 SMPI2 SMPI1 SMPI0 BUFM ALTS bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 VCFG<2:0>: Voltage Reference Configuration bits VCFG<2:0> VR+ VR- 000 AVDD AVSS 001 External VREF+ pin AVSS 010 AVDD External VREF- pin 011 External VREF+ pin External VREF- pin 1xx AVDD AVSS bit 12 Reserved: Maintain as ‘0’ bit 11 Unimplemented: Read as ‘0’ bit 10 CSCNA: Scan Input Selections for S/H Positive Input for MUX A Input Multiplexer Setting bit 1 = Scan inputs 0 = Do not scan inputs bit 9-8 Unimplemented: Read as ‘0’ bit 7 BUFS: Buffer Fill Status bit (valid only when BUFM = 1) 1 = A/D is currently filling buffer 08-0F, user should access data in 00-07 0 = A/D is currently filling buffer 00-07, user should access data in 08-0F bit 6 Unimplemented: Read as ‘0’ bit 5-2 SMPI<3:0>: Sample/Convert Sequences Per Interrupt Selection bits 1111 = Interrupts at the completion of conversion for each 16th sample/convert sequence 1110 = Interrupts at the completion of conversion for each 15th sample/convert sequence ..... 0001 = Interrupts at the completion of conversion for each 2nd sample/convert sequence 0000 = Interrupts at the completion of conversion for each sample/convert sequence bit 1 BUFM: Buffer Mode Select bit 1 = Buffer configured as two 8-word buffers (ADC1BUFn<15:8> and ADC1BUFn<7:0>) 0 = Buffer configured as one 16-word buffer (ADC1BUFn<15:0>) bit 0 ALTS: Alternate Input Sample Mode Select bit 1 = Uses MUX A input multiplexer settings for first sample, then alternates between MUX B and MUXA input multiplexer settings for all subsequent samples 0 = Always uses MUX A input multiplexer settings DS39905E-page 228  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 21-3: AD1CON3: A/D CONTROL REGISTER 3 R/W-0 r-0 r-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADRC r r SAMC4 SAMC3 SAMC2 SAMC1 SAMC0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADCS7 ADCS6 ADCS5 ADCS4 ADCS3 ADCS2 ADCS1 ADCS0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ADRC: A/D Conversion Clock Source bit 1 = A/D internal RC clock 0 = Clock derived from system clock bit 14-13 Reserved: Maintain as ‘0’ bit 12-8 SAMC<4:0>: Auto-Sample Time bits 11111 = 31 TAD ····· 00001 = 1 TAD 00000 = 0 TAD (not recommended) bit 7-0 ADCS<7:0>: A/D Conversion Clock Select bits 11111111 ······ = Reserved, do not use 01000000 00111111 = 64 TCY 00111110 = 63 TCY ······ 00000001 = 2 * TCY 00000000 = TCY  2010 Microchip Technology Inc. DS39905E-page 229

PIC24FJ256GA110 FAMILY REGISTER 21-4: AD1CHS: A/D INPUT SELECT REGISTER R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CH0NB — — CH0SB4(1) CH0SB3(1) CH0SB2(1) CH0SB1(1) CH0SB0(1) bit 15 bit 8 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CH0NA — — CH0SA4 CH0SA3 CH0SA2 CH0SA1 CH0SA0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CH0NB: Channel 0 Negative Input Select for MUX B Multiplexer Setting bit 1 = Channel 0 negative input is AN1 0 = Channel 0 negative input is VR- bit 14-13 Unimplemented: Read as ‘0’ bit 12-8 CH0SB<4:0>: Channel 0 Positive Input Select for MUX B Multiplexer Setting bits(1) 10001 = Channel 0 positive input is internal band gap reference (VBG) 10000 = Channel 0 positive input is VBG/2 01111 = Channel 0 positive input is AN15 01110 = Channel 0 positive input is AN14 01101 = Channel 0 positive input is AN13 01100 = Channel 0 positive input is AN12 01011 = Channel 0 positive input is AN11 01010 = Channel 0 positive input is AN10 01001 = Channel 0 positive input is AN9 01000 = Channel 0 positive input is AN8 00111 = Channel 0 positive input is AN7 00110 = Channel 0 positive input is AN6 00101 = Channel 0 positive input is AN5 00100 = Channel 0 positive input is AN4 00011 = Channel 0 positive input is AN3 00010 = Channel 0 positive input is AN2 00001 = Channel 0 positive input is AN1 00000 = Channel 0 positive input is AN0 bit 7 CH0NA: Channel 0 Negative Input Select for MUX A Multiplexer Setting bit 1 = Channel 0 negative input is AN1 0 = Channel 0 negative input is VR- bit 6-5 Unimplemented: Read as ‘0’ bit 4-0 CH0SA<4:0>: Channel 0 Positive Input Select for MUX A Multiplexer Setting bits Implemented combinations are identical to those for CHOSB<4:0> (above). Note 1: Combinations, ‘10010’ through ‘11111’, are unimplemented; do not use. DS39905E-page 230  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 21-5: AD1PCFGL: A/D PORT CONFIGURATION REGISTER (LOW) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCFG15 PCFG14 PCFG13 PCFG12 PCFG11 PCFG10 PCFG9 PCFG8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 PCFG<15:0>: Analog Input Pin Configuration Control bits 1 = Pin for corresponding analog channel is configured in Digital mode; I/O port read enabled 0 = Pin configured in Analog mode; I/O port read disabled, A/D samples pin voltage REGISTER 21-6: AD1PCFGH: A/D PORT CONFIGURATION REGISTER (HIGH) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — PCFG17 PCFG16 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-2 Unimplemented: Read as ‘0’ bit 1 PCFG17: A/D Input Band Gap Scan Enable bit 1 = Analog channel disabled from input scan 0 = Internal band gap (VBG) channel enabled for input scan bit 0 PCFG16: A/D Input Half Band Gap Scan Enable bit 1 = Analog channel disabled from input scan 0 = Internal VBG/2 channel enabled for input scan  2010 Microchip Technology Inc. DS39905E-page 231

PIC24FJ256GA110 FAMILY REGISTER 21-7: AD1CSSL: A/D INPUT SCAN SELECT REGISTER (LOW) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CSSL15 CSSL14 CSSL13 CSSL12 CSSL11 CSSL10 CSSL9 CSSL8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CSSL7 CSSL6 CSSL5 CSSL4 CSSL3 CSSL2 CSSL1 CSSL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 CSSL<15:0>: A/D Input Pin Scan Selection bits 1 = Corresponding analog channel selected for input scan 0 = Analog channel omitted from input scan DS39905E-page 232  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY EQUATION 21-1: A/D CONVERSION CLOCK PERIOD(1) TAD = TCY • (ADCS + 1) TAD ADCS = – 1 TCY Note 1: Based on TCY = 2 * TOSC, Doze mode and PLL are disabled. FIGURE 21-2: 10-BIT A/D CONVERTER ANALOG INPUT MODEL VDD RIC  250 Sampling RSS  5 k(Typical) Switch VT = 0.6V Rs ANx RSS CHOLD VA C6-P1I1N pF VT = 0.6V IL5E0A0K AnGAE == D4.A4 Cp Fc a(pTaypciitcaanl)ce (Typical) VSS Legend: CPIN = Input Capacitance VT = Threshold Voltage ILEAKAGE = Leakage Current at the pin due to various junctions RIC = Interconnect Resistance RSS = Sampling Switch Resistance CHOLD = Sample/Hold Capacitance (from DAC) Note: CPIN value depends on device package and is not tested. The effect of CPIN is negligible if Rs  5 k.  2010 Microchip Technology Inc. DS39905E-page 233

PIC24FJ256GA110 FAMILY FIGURE 21-3: A/D TRANSFER FUNCTION Output Code (Binary (Decimal)) 11 1111 1111 (1023) 11 1111 1110 (1022) 10 0000 0011 (515) 10 0000 0010 (514) 10 0000 0001 (513) 10 0000 0000 (512) 01 1111 1111 (511) 01 1111 1110 (510) 01 1111 1101 (509) 00 0000 0001 (1) 00 0000 0000 (0) Voltage Level 0 V-R V+ – V-RRV- +R1024 512*(V+ – V-)RR 1024 1023*(V+ – V-)RR 1024V+R (V – V)INHINL V- +R V- +R DS39905E-page 234  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 22.0 TRIPLE COMPARATOR The comparator outputs may be directly connected to MODULE the CxOUT pins. When the respective COE equals ‘1’, the I/O pad logic makes the unsynchronized output of Note: This data sheet summarizes the features of the comparator available on the pin. this group ofPIC24F devices. It is not A simplified block diagram of the module in shown in intended to be a comprehensive reference Figure22-1. Diagrams of the possible individual source. For more information, refer to the comparator configurations are shown in Figure22-2. “PIC24F Family Reference Manual”, Each comparator has its own control register, Section 19. “Comparator Module” CMxCON (Register22-1), for enabling and configuring (DS39710). its operation. The output and event status of all three The triple comparator module provides three dual-input comparators are provided in the CMSTAT register comparators. The inputs to the comparator can be con- (Register22-2). figured to use any one of four external analog inputs, as well as a voltage reference input from either the internal band gap reference divided by two (VBG/2) or the comparator voltage reference generator. FIGURE 22-1: TRIPLE COMPARATOR MODULE BLOCK DIAGRAM EVPOL<1:0> CCH<1:0> CREF Trigger/Interrupt CEVT Logic CPOL COE VIN- C1 CXINB VIN+ Input C1OUT CXINC Select COUT Pin Logic CXIND EVPOL<1:0> VBG/2 Trigger/Interrupt CEVT Logic CPOL COE VIN- C2 VIN+ C2OUT COUT Pin EVPOL<1:0> CXINA Trigger/Interrupt CEVT CVREF Logic CPOL COE VIN- C3 VIN+ C3OUT COUT Pin  2010 Microchip Technology Inc. DS39905E-page 235

PIC24FJ256GA110 FAMILY FIGURE 22-2: INDIVIDUAL COMPARATOR CONFIGURATIONS Comparator Off CEN=0, CREF=x, CCH<1:0>=xx COE VIN- Cx VIN+ Off (Read as ‘0’) CxOUT Pin Comparator CxINB > CxINA Compare Comparator CxINC > CxINA Compare CEN=1, CREF=0, CCH<1:0>=00 CEN=1, CREF=0, CCH<1:0>=01 COE COE CXINB VIN- CXINC VIN- Cx Cx VIN+ VIN+ CXINA CxOUT CXINA CxOUT Pin Pin Comparator CxIND > CxINA Compare Comparator VBG > CxINA Compare CEN=1, CREF=0, CCH<1:0>=10 CEN=1, CREF=0, CCH<1:0>=11 COE COE CXIND VIN- VBG/2 VIN- Cx Cx VIN+ VIN+ CXINA CxOUT CXINA CxOUT Pin Pin Comparator CxINB > CVREF Compare Comparator CxINC > CVREF Compare CEN=1, CREF=1, CCH<1:0>=00 CEN=1, CREF=1, CCH<1:0>=01 COE COE CXINB VIN- CXINC VIN- Cx Cx VIN+ VIN+ CVREF CxOUT CVREF CxOUT Pin Pin Comparator CxIND > CVREF Compare Comparator VBG > CVREF Compare CEN=1, CREF=1, CCH<1:0>=10 CEN=1, CREF=1, CCH<1:0>=11 COE COE CXIND VIN- VBG/2 VIN- Cx Cx VIN+ VIN+ CVREF CxOUT CVREF CxOUT Pin Pin DS39905E-page 236  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 22-1: CMxCON: COMPARATOR x CONTROL REGISTERS (COMPARATORS 1 THROUGH 3) R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 R-0 CEN COE CPOL — — — CEVT COUT bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 R/W-0 EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CEN: Comparator Enable bit 1 = Comparator is enabled 0 = Comparator is disabled bit 14 COE: Comparator Output Enable bit 1 = Comparator output is present on the CxOUT pin. 0 = Comparator output is internal only bit 13 CPOL: Comparator Output Polarity Select bit 1 = Comparator output is inverted 0 = Comparator output is not inverted bit 12-10 Unimplemented: Read as ‘0’ bit 9 CEVT: Comparator Event bit 1 = Comparator event defined by EVPOL<1:0> has occurred; subsequent triggers and interrupts are disabled until the bit is cleared 0 = Comparator event has not occurred bit 8 COUT: Comparator Output bit When CPOL = 0: 1 = VIN+ > VIN- 0 = VIN+ < VIN- When CPOL = 1: 1 = VIN+ < VIN- 0 = VIN+ > VIN- bit 7-6 EVPOL<1:0>: Trigger/Event/Interrupt Polarity Select bits 11 = Trigger/event/interrupt generated on any change of the comparator output (while CEVT=0) 10 = Trigger/event/interrupt generated on transition of the comparator output: If CPOL = 0 (non-inverted polarity): High-to-low transition only. If CPOL = 1 (inverted polarity): Low-to-high transition only. 01 = Trigger/Event/Interrupt generated on transition of comparator output: If CPOL = 0 (non-inverted polarity): Low-to-high transition only. If CPOL = 1 (inverted polarity): High-to-low transition only. 00 = Trigger/event/interrupt generation is disabled bit 5 Unimplemented: Read as ‘0’  2010 Microchip Technology Inc. DS39905E-page 237

PIC24FJ256GA110 FAMILY REGISTER 22-1: CMxCON: COMPARATOR x CONTROL REGISTERS (COMPARATORS 1 THROUGH 3) (CONTINUED) bit 4 CREF: Comparator Reference Select bits (non-inverting input) 1 = Non-inverting input connects to internal CVREF voltage 0 = Non-inverting input connects to CXINA pin bit 3-2 Unimplemented: Read as ‘0’ bit 1-0 CCH<1:0>: Comparator Channel Select bits 11 = Inverting input of comparator connects to VBG/2 10 = Inverting input of comparator connects to CXIND pin 01 = Inverting input of comparator connects to CXINC pin 00 = Inverting input of comparator connects to CXINB pin REGISTER 22-2: CMSTAT: COMPARATOR MODULE STATUS REGISTER R/W-0 U-0 U-0 U-0 U-0 R-0 R-0 R-0 CMIDL — — — — C3EVT C2EVT C1EVT bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R-0 R-0 R-0 — — — — — C3OUT C2OUT C1OUT bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CMIDL: Comparator Stop in Idle Mode bit 1 = Module does not generate interrupts in Idle mode, but is otherwise operational 0 = Module continues normal operation in Idle mode bit 14-11 Unimplemented: Read as ‘0’ bit 10 C3EVT: Comparator 3 Event Status bit (read-only) Shows the current event status of Comparator 3 (CM3CON<9>). bit 9 C2EVT: Comparator 2 Event Status bit (read-only) Shows the current event status of Comparator 2 (CM2CON<9>). bit 8 C1EVT: Comparator 1 Event Status bit (read-only) Shows the current event status of Comparator 1 (CM1CON<9>). bit 7-3 Unimplemented: Read as ‘0’ bit 2 C3OUT: Comparator 3 Output Status bit (read-only) Shows the current output of Comparator 3 (CM3CON<8>). bit 1 C2OUT: Comparator 2 Output Status bit (read-only) Shows the current output of Comparator 2 (CM2CON<8>). bit 0 C1OUT: Comparator 1 Output Status bit (read-only) Shows the current output of Comparator 1 (CM1CON<8>). DS39905E-page 238  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 23.0 COMPARATOR VOLTAGE voltage, each with 16 distinct levels. The range to be REFERENCE used is selected by the CVRR bit (CVRCON<5>). The primary difference between the ranges is the size of the Note: This data sheet summarizes the features of steps selected by the CVREF Selection bits this group of PIC24F devices. It is not (CVR<3:0>), with one range offering finer resolution. intended to be a comprehensive reference The comparator reference supply voltage can come source. For more information, refer to the from either VDD and VSS, or the external VREF+ and “PIC24F Family Reference Manual”, VREF-. The voltage source is selected by the CVRSS Section 20. “Comparator Voltage bit (CVRCON<4>). Reference Module” (DS39709). The settling time of the comparator voltage reference must be considered when changing the CVREF 23.1 Configuring the Comparator output. Voltage Reference The voltage reference module is controlled through the CVRCON register (Register23-1). The comparator voltage reference provides two ranges of output FIGURE 23-1: COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM CVRSS = 1 VREF+ AVDD CVRSS = 0 8R CVR<3:0> R CVREN R R R X U M 16 Steps 1 CVREF o- 6-t 1 R R R CVRR 8R CVRSS = 1 VREF- CVRSS = 0 AVSS  2010 Microchip Technology Inc. DS39905E-page 239

PIC24FJ256GA110 FAMILY REGISTER 23-1: CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CVREN CVROE CVRR CVRSS CVR3 CVR2 CVR1 CVR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 CVREN: Comparator Voltage Reference Enable bit 1 = CVREF circuit powered on 0 = CVREF circuit powered down bit 6 CVROE: Comparator VREF Output Enable bit 1 = CVREF voltage level is output on CVREF pin 0 = CVREF voltage level is disconnected from CVREF pin bit 5 CVRR: Comparator VREF Range Selection bit 1 = CVRSRC range should be 0 to 0.625 CVRSRC with CVRSRC/24 step size 0 = CVRSRC range should be 0.25 to 0.719 CVRSRC with CVRSRC/32 step size bit 4 CVRSS: Comparator VREF Source Selection bit 1 = Comparator reference source, CVRSRC = VREF+ – VREF- 0 = Comparator reference source, CVRSRC = AVDD – AVSS bit 3-0 CVR<3:0>: Comparator VREF Value Selection, 0  CVR<3:0>  15, bits When CVRR = 1: CVREF = (CVR<3:0>/ 24)  (CVRSRC) When CVRR = 0: CVREF = 1/4  (CVRSRC) + (CVR<3:0>/32)  (CVRSRC) DS39905E-page 240  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 24.0 CHARGE TIME 24.1 Measuring Capacitance MEASUREMENT UNIT (CTMU) The CTMU module measures capacitance by generat- ing an output pulse, with a width equal to the time, Note: This data sheet summarizes the features between edge events on two separate input channels. of this group ofPIC24F devices. It is not The pulse edge events to both input channels can be intended to be a comprehensive selected from four sources: two internal peripheral reference source. For more information, modules (OC1 and Timer1) and two external pins refer to the “PIC24F Family Reference (CTEDG1 and CTEDG2). This pulse is used with the Manual”, Section 11. “Charge Time module’s precision current source to calculate Measurement Unit (CTMU)” (DS39724). capacitance according to the relationship The Charge Time Measurement Unit is a flexible analog dV I = C • module that provides accurate differential time measure- dT ment between pulse sources, as well as asynchronous pulse generation. Its key features include: For capacitance measurements, the A/D Converter samples an external capacitor (CAPP) on one of its • Four edge input trigger sources input channels after the CTMU output’s pulse. A Preci- • Polarity control for each edge source sion Resistor (RPR) provides current source calibration • Control of edge sequence on a second A/D channel. After the pulse ends, the • Control of response to edges converter determines the voltage on the capacitor. The • Time measurement resolution of 1nanosecond actual calculation of capacitance is performed in software by the application. • Accurate current source suitable for capacitive measurement Figure24-1 shows the external connections used for capacitance measurements, and how the CTMU and Together with other on-chip analog modules, the CTMU A/D modules are related in this application. This can be used to precisely measure time, measure example also shows the edge events coming from capacitance, measure relative changes in capacitance Timer1, but other configurations using external edge or generate output pulses that are independent of the sources are possible. A detailed discussion on measur- system clock. The CTMU module is ideal for interfacing ing capacitance and time with the CTMU module is with capacitive-based sensors. provided in the “PIC24F Family Reference Manual”. The CTMU is controlled through two registers: CTMUCON and CTMUICON. CTMUCON enables the module and controls edge source selection, edge source polarity selection, and edge sequencing. The CTMUICON register controls the selection and trim of the current source. FIGURE 24-1: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR CAPACITANCE MEASUREMENT PIC24FJ Device Timer1 CTMU EDG1 Current Source EDG2 Output Pulse A/D Converter ANx ANY CAPP RPR  2010 Microchip Technology Inc. DS39905E-page 241

PIC24FJ256GA110 FAMILY 24.2 Measuring Time When the module is configured for pulse generation delay by setting the TGEN bit (CTMUCON<12>), the Time measurements on the pulse width can be similarly internal current source is connected to the B input of performed using the A/D module’s internal capacitor Comparator 2. A capacitor (CDELAY) is connected to (CAD) and a precision resistor for current calibration. the Comparator 2 pin C2INB, and the comparator volt- Figure24-2 shows the external connections used for age reference, CVREF, is connected to C2INA. CVREF time measurements, and how the CTMU and A/D is then configured for a specific trip point. The module modules are related in this application. This example begins to charge CDELAY when an edge event is also shows both edge events coming from the external detected. When CDELAY charges above the CVREF trip CTEDG pins, but other configurations using internal point, a pulse is output on CTPLS. The length of the edge sources are possible. A detailed discussion on pulse delay is determined by the value of CDELAY and measuring capacitance and time with the CTMU module the CVREF trip point. is provided in the “PIC24F Family Reference Manual”. Figure24-3 shows the external connections for pulse generation, as well as the relationship of the different 24.3 Pulse Generation and Delay analog modules required. While CTEDG1 is shown as The CTMU module can also generate an output pulse the input pulse source, other options are available. A with edges that are not synchronous with the device’s detailed discussion on pulse generation with the CTMU system clock. More specifically, it can generate a pulse module is provided in the “PIC24F Family Reference with a programmable delay from an edge event input to Manual”. the module. FIGURE 24-2: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR TIME MEASUREMENT PIC24FJ Device CTMU CTEDG1 EDG1 Current Source CTEDG2 EDG2 Output Pulse A/D Converter ANx CAD RPR FIGURE 24-3: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR PULSE DELAY GENERATION PIC24FJ Device CTMU CTEDG1 EDG1 CTPLS Current Source Comparator C2INB C2 CDELAY CVREF DS39905E-page 242  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 24-1: CTMUCON: CTMU CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CTMUEN — CTMUSIDL TGEN EDGEN EDGSEQEN IDISSEN CTTRIG bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EDG2POL EDG2SEL1 EDG2SEL0 EDG1POL EDG1SEL1 EDG1SEL0 EDG2STAT EDG1STAT bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CTMUEN: CTMU Enable bit 1 = Module is enabled 0 = Module is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 CTMUSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12 TGEN: Time Generation Enable bit(1) 1 = Enables edge delay generation 0 = Disables edge delay generation bit 11 EDGEN: Edge Enable bit 1 = Edges are not blocked 0 = Edges are blocked bit 10 EDGSEQEN: Edge Sequence Enable bit 1 = Edge 1 event must occur before Edge 2 event can occur 0 = No edge sequence is needed bit 9 IDISSEN: Analog Current Source Control bit 1 = Analog current source output is grounded 0 = Analog current source output is not grounded bit 8 CTTRIG: Trigger Control bit 1 = Trigger output is enabled 0 = Trigger output is disabled bit 7 EDG2POL: Edge 2 Polarity Select bit 1 = Edge 2 programmed for a positive edge response 0 = Edge 2 programmed for a negative edge response bit 6-5 EDG2SEL<1:0>: Edge 2 Source Select bits 11 = CTED1 pin 10 = CTED2 pin 01 = OC1 module 00 = Timer1 module bit 4 EDG1POL: Edge 1 Polarity Select bit 1 = Edge 1 programmed for a positive edge response 0 = Edge 1 programmed for a negative edge response Note 1: If TGEN = 1, the CTEDGx inputs and CTPLS outputs must be assigned to available RPn pins before use. See Section10.4 “Peripheral Pin Select” for more information.  2010 Microchip Technology Inc. DS39905E-page 243

PIC24FJ256GA110 FAMILY REGISTER 24-1: CTMUCON: CTMU CONTROL REGISTER (CONTINUED) bit 3-2 EDG1SEL<1:0>: Edge 1 Source Select bits 11 = CTED1 pin 10 = CTED2 pin 01 = OC1 module 00 = Timer1 module bit 1 EDG2STAT: Edge 2 Status bit 1 = Edge 2 event has occurred 0 = Edge 2 event has not occurred bit 0 EDG1STAT: Edge 1 Status bit 1 = Edge 1 event has occurred 0 = Edge 1 event has not occurred Note 1: If TGEN = 1, the CTEDGx inputs and CTPLS outputs must be assigned to available RPn pins before use. See Section10.4 “Peripheral Pin Select” for more information. REGISTER 24-2: CTMUICON: CTMU CURRENT CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ITRIM5 ITRIM4 ITRIM3 ITRIM2 ITRIM1 ITRIM0 IRNG1 IRNG0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 ITRIM<5:0>: Current Source Trim bits 011111 = Maximum positive change from nominal current 011110 . . . . . 000001 = Minimum positive change from nominal current 000000 = Nominal current output specified by IRNG<1:0> 111111 = Minimum negative change from nominal current . . . . . 100010 100001 = Maximum negative change from nominal current bit 9-8 IRNG<1:0>: Current Source Range Select bits 11 = 100  Base Current 10 = 10  Base Current 01 = Base current level (0.55A nominal) 00 = Current source disabled bit 7-0 Unimplemented: Read as ‘0’ DS39905E-page 244  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 25.0 SPECIAL FEATURES 25.1.1 CONSIDERATIONS FOR CONFIGURING PIC24FJ256GA110 Note: This data sheet summarizes the features FAMILY DEVICES of this group of PIC24F devices. It is not In PIC24FJ256GA110 family devices, the configuration intended to be a comprehensive refer- bytes are implemented as volatile memory. This means ence source. For more information, refer that configuration data must be programmed each time to the following sections of the “PIC24F the device is powered up. Configuration data is stored Family Reference Manual”: in the three words at the top of the on-chip program • Section 9. “Watchdog Timer (WDT)” memory space, known as the Flash Configuration (DS39697) Words. Their specific locations are shown in • Section 32. “High-Level Device Table25-1. These are packed representations of the Integration” (DS39719) actual device Configuration bits, whose actual • Section 33. “Programming and locations are distributed among several locations in Diagnostics” (DS39716) configuration space. The configuration data is automat- ically loaded from the Flash Configuration Words to the PIC24FJ256GA110 family devices include several proper Configuration registers during device Resets. features intended to maximize application flexibility and reliability, and minimize cost through elimination of Note: Configuration data is reloaded on all types external components. These are: of device Resets. • Flexible Configuration When creating applications for these devices, users • Watchdog Timer (WDT) should always specifically allocate the location of the • Code Protection Flash Configuration Word for configuration data. This is • JTAG Boundary Scan Interface to make certain that program code is not stored in this address when the code is compiled. • In-Circuit Serial Programming • In-Circuit Emulation The upper byte of all Flash Configuration Words in pro- gram memory should always be ‘1111 1111’. This 25.1 Configuration Bits makes them appear to be NOP instructions in the remote event that their locations are ever executed by The Configuration bits can be programmed (read as ‘0’), accident. Since Configuration bits are not implemented or left unprogrammed (read as ‘1’), to select various in the corresponding locations, writing ‘1’s to these device configurations. These bits are mapped starting at locations has no effect on device operation. program memory location F80000h. A detailed explana- Note: Performing a page erase operation on the tion of the various bit functions is provided in last page of program memory clears the Register25-1 through Register25-5. Flash Configuration Words, enabling code Note that address F80000h is beyond the user program protection as a result. Therefore, users memory space. In fact, it belongs to the configuration should avoid performing page erase memory space (800000h-FFFFFFh) which can only be operations on the last page of program accessed using table reads and table writes. memory. TABLE 25-1: FLASH CONFIGURATION WORD LOCATIONS FOR PIC24FJ256GA110 FAMILY DEVICES Configuration Word Addresses Device 1 2 3 PIC24FJ64GA1 ABFEh ABFCh ABFAh PIC24FJ128GA1 157FEh 157FC 157FA PIC24FJ192GA1 20BFEh 20BFC 20BFA PIC24FJ256GA1 2ABFEh 2ABFC 2ABFA  2010 Microchip Technology Inc. DS39905E-page 245

PIC24FJ256GA110 FAMILY REGISTER 25-1: CW1: FLASH CONFIGURATION WORD 1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 — — — — — — — — bit 23 bit 16 r-x R/PO-1 R/PO-1 R/PO-1 R/PO-1 r-1 R/PO-1 R/PO-1 r JTAGEN GCP GWRP DEBUG r ICS1 ICS0 bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 FWDTEN WINDIS — FWPSA WDTPS3 WDTPS2 WDTPS1 WDTPS0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit PO = Program Once bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Reserved bit 15 Reserved: The value is unknown; program as ‘0’ bit 14 JTAGEN: JTAG Port Enable bit 1 = JTAG port is enabled 0 = JTAG port is disabled bit 13 GCP: General Segment Program Memory Code Protection bit 1 = Code protection is disabled 0 = Code protection is enabled for the entire program memory space bit 12 GWRP: General Segment Code Flash Write Protection bit 1 = Writes to program memory are allowed 0 = Writes to program memory are disabled bit 11 DEBUG: Background Debugger Enable bit 1 = Device resets into Operational mode 0 = Device resets into Debug mode bit 10 Reserved: Always maintain as ‘1’ bit 9-8 ICS<1:0>: Emulator Pin Placement Select bits 11 = Emulator functions are shared with PGEC1/PGED1 10 = Emulator functions are shared with PGEC2/PGED2 01 = Emulator functions are shared with PGEC3/PGED3 00 = Reserved; do not use bit 7 FWDTEN: Watchdog Timer Enable bit 1 = Watchdog Timer is enabled 0 = Watchdog Timer is disabled bit 6 WINDIS: Windowed Watchdog Timer Disable bit 1 = Standard Watchdog Timer enabled 0 = Windowed Watchdog Timer enabled; FWDTEN must be ‘1’ bit 5 Reserved bit 4 FWPSA: WDT Prescaler Ratio Select bit 1 = Prescaler ratio of 1:128 0 = Prescaler ratio of 1:32 DS39905E-page 246  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 25-1: CW1: FLASH CONFIGURATION WORD 1 (CONTINUED) bit 3-0 WDTPS<3:0>: Watchdog Timer Postscaler Select bits 1111 = 1:32,768 1110 = 1:16,384 1101 = 1:8,192 1100 = 1:4,096 1011 = 1:2,048 1010 = 1:1,024 1001 = 1:512 1000 = 1:256 0111 = 1:128 0110 = 1:64 0101 = 1:32 0100 = 1:16 0011 = 1:8 0010 = 1:4 0001 = 1:2 0000 = 1:1  2010 Microchip Technology Inc. DS39905E-page 247

PIC24FJ256GA110 FAMILY REGISTER 25-2: CW2: FLASH CONFIGURATION WORD 2 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 IESO — — — — FNOSC2 FNOSC1 FNOSC0 bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 FCKSM1 FCKSM0 OSCIOFCN IOL1WAY — I2C2SEL(1) POSCMD1 POSCMD0 bit 7 bit 0 Legend: R = Readable bit PO = Program Once bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Reserved bit 15 IESO: Internal External Switchover bit 1 = IESO mode (Two-Speed Start-up) enabled 0 = IESO mode (Two-Speed Start-up) disabled bit 14-11 Reserved bit 10-8 FNOSC<2:0>: Initial Oscillator Select bits 111 = Fast RC Oscillator with Postscaler (FRCDIV) 110 = Reserved 101 = Low-Power RC Oscillator (LPRC) 100 = Secondary Oscillator (SOSC) 011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = Fast RC Oscillator with Postscaler and PLL module (FRCPLL) 000 = Fast RC Oscillator (FRC) bit 7-6 FCKSM<1:0>: Clock Switching and Fail-Safe Clock Monitor Configuration bits 1x = Clock switching and Fail-Safe Clock Monitor are disabled 01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled 00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled bit 5 OSCIOFCN: OSCO Pin Configuration bit If POSCMD<1:0> = 11 or 00: 1 = OSCO/CLKO/RC15 functions as CLKO (FOSC/2) 0 = OSCO/CLKO/RC15 functions as port I/O (RC15) If POSCMD<1:0> = 10 or 01: OSCIOFCN has no effect on OSCO/CLKO/RC15. bit 4 IOL1WAY: IOLOCK One-Way Set Enable bit 1 = The IOLOCK bit (OSCCON<6>) can be set once, provided the unlock sequence has been completed. Once set, the Peripheral Pin Select registers cannot be written to a second time. 0 = The IOLOCK bit can be set and cleared as needed, provided the unlock sequence has been completed bit 3 Reserved bit 2 I2C2SEL: I2C2 Pin Select bit(1) 1 = Use SCL2/SDA2 pins for I2C2 0 = Use ASCL2/ASDA2 pins for I2C2 Note 1: Implemented in 100-pin devices only; otherwise unimplemented, read as ‘1’. DS39905E-page 248  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY REGISTER 25-2: CW2: FLASH CONFIGURATION WORD 2 (CONTINUED) bit 1-0 POSCMD<1:0>: Primary Oscillator Configuration bits 11 = Primary Oscillator disabled 10 = HS Oscillator mode selected 01 = XT Oscillator mode selected 00 = EC Oscillator mode selected Note 1: Implemented in 100-pin devices only; otherwise unimplemented, read as ‘1’. REGISTER 25-3: CW3: FLASH CONFIGURATION WORD 3 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 WPEND WPCFG WPDIS — — — — — bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 WPFP7 WPFP6 WPFP5 WPFP4 WPFP3 WPFP2 WPFP1 WPFP0 bit 7 bit 0 Legend: R = Readable bit PO = Program Once bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Reserved bit 15 WPEND: Segment Write Protection End Page Select bit 1 = Protected code segment upper boundary is at the last page of program memory; lower boundary is the code page specified by WPFP<7:0> 0 = Protected code segment lower boundary is at the bottom of program memory (000000h); upper boundary is the code page specified by WPFP<7:0> bit 14 WPCFG: Configuration Word Code Page Protection Select bit 1 = Last page (at the top of program memory) and Flash Configuration Words are not protected if WPEND = 0 0 = Last page and Flash Configuration Words are code-protected if WPEND = 0 bit 13 WPDIS: Segment Write Protection Disable bit 1 = Segmented code protection disabled 0 = Segmented code protection enabled; protected segment defined by WPEND, WPCFG and WPFPx Configuration bits bit 12-8 Reserved bit 7-0 WPFP<7:0>: Protected Code Segment Boundary Page bits Designates the 512-word program code page that is the boundary of the protected code segment, starting with Page 0 at the bottom of program memory. If WPEND = 1: First address of designated code page is the lower boundary of the segment. If WPEND = 0: Last address of designated code page is the upper boundary of the segment.  2010 Microchip Technology Inc. DS39905E-page 249

PIC24FJ256GA110 FAMILY REGISTER 25-4: DEVID: DEVICE ID REGISTER U U U U U U U U — — — — — — — — bit 23 bit 16 U U R R R R R R — — FAMID7 FAMID6 FAMID5 FAMID4 FAMID3 FAMID2 bit 15 bit 8 R R R R R R R R FAMID1 FAMID0 DEV5 DEV4 DEV3 DEV2 DEV1 DEV0 bit 7 bit 0 Legend: R = Read-Only bit U = Unimplemented bit bit 23-14 Unimplemented: Read as ‘1’ bit 13-6 FAMID<7:0>: Device Family Identifier bits 01000000 = PIC24FJ256GA110 family bit 5-0 DEV<5:0>: Individual Device Identifier bits 000000 = PIC24FJ64GA106 000010 = PIC24FJ64GA108 000110 = PIC24FJ64GA110 001000 = PIC24FJ128GA106 001010 = PIC24FJ128GA108 001110 = PIC24FJ128GA110 010000 = PIC24FJ192GA106 010010 = PIC24FJ192GA108 010110 = PIC24FJ192GA110 011000 = PIC24FJ256GA106 011010 = PIC24FJ256GA108 011110 = PIC24FJ256GA110 REGISTER 25-5: DEVREV: DEVICE REVISION REGISTER U U U U U U U U — — — — — — — — bit 23 bit 16 U U U U U U U R — — — — — — — MAJRV2 bit 15 bit 8 R R U U U R R R MAJRV1 MAJRV0 — — — DOT2 DOT1 DOT0 bit 7 bit 0 Legend: R = Read-Only bit U = Unimplemented bit bit 23-9 Unimplemented: Read as ‘0’ bit 8-6 MAJRV<2:0>: Major Revision Identifier bits bit 5-3 Unimplemented: Read as ‘0’ bit 2-0 DOT<2:0>: Minor Revision Identifier bits DS39905E-page 250  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 25.2 On-Chip Voltage Regulator FIGURE 25-1: CONNECTIONS FOR THE ON-CHIP REGULATOR All PIC24FJ256GA110 family devices power their core digital logic at a nominal 2.5V. This may create an issue Regulator Enabled (ENVREG tied to VDD): for designs that are required to operate at a higher 3.3V typical voltage, such as 3.3V. To simplify system design, all devices in the PIC24FJ256GA110 family PIC24FJ256GA incorporate an on-chip regulator that allows the device VDD to run its core logic from VDD. ENVREG The regulator is controlled by the ENVREG pin. Tying VDD VDDCORE/VCAP to the pin enables the regulator, which in turn, provides CEFC power to the core from the other VDD pins. When the reg- (10F typ) VSS ulator is enabled, a low-ESR capacitor (such as ceramic) must be connected to the VDDCORE/VCAP pin (Figure25-1). This helps to maintain the stability of the regulator. The recommended value for the filter capacitor (CEFC) is provided in Section28.1 “DC Characteristics”. Regulator Disabled (ENVREG tied to ground): If ENVREG is tied to VSS, the regulator is disabled. In 2.5V(1) 3.3V(1) this case, separate power for the core logic at a nomi- nal 2.5V must be supplied to the device on the PIC24FJ256GA VDDCORE/VCAP pin to run the I/O pins at higher voltage VDD levels, typically 3.3V. Alternatively, the VDDCORE/VCAP ENVREG and VDD pins can be tied together to operate at a lower nominal voltage. Refer to Figure25-1 for possible VDDCORE/VCAP configurations. VSS 25.2.1 VOLTAGE REGULATOR TRACKING MODE AND LOW-VOLTAGE DETECTION When it is enabled, the on-chip regulator provides a Regulator Disabled (VDD tied to VDDCORE): constant voltage of 2.5V nominal to the digital core logic. 2.5V(1) PIC24FJ256GA The regulator can provide this level from a VDD of about 2.5V, all the way up to the device’s VDDMAX. It does not VDD have the capability to boost VDD levels below 2.5V. In ENVREG order to prevent “brown-out” conditions when the volt- age drops too low for the regulator, the regulator enters VDDCORE/VCAP Tracking mode. In Tracking mode, the regulator output VSS follows VDD with a typical voltage drop of 100mV. When the device enters Tracking mode, it is no longer possible to operate at full speed. To provide information Note 1: These are typical operating voltages. Refer about when the device enters Tracking mode, the to Section28.1 “DC Characteristics” for on-chip regulator includes a simple, Low-Voltage the full operating ranges of VDD and Detect circuit. When VDD drops below full-speed oper- VDDCORE. ating voltage, the circuit sets the Low-Voltage Detect Interrupt Flag, LVDIF (IFS4<8>). This can be used to generate an interrupt and put the application into a Low-Power Operational mode or trigger an orderly shutdown. Low-Voltage Detection is only available when the regulator is enabled.  2010 Microchip Technology Inc. DS39905E-page 251

PIC24FJ256GA110 FAMILY 25.2.2 ON-CHIP REGULATOR AND POR For applications which require a faster wake-up time, it is possible to disable regulator Standby mode. The When the voltage regulator is enabled, it takes approxi- PMSLP bit can be set to turn off Standby mode so that mately 10s for it to generate output. During this time, the Flash stays powered when in Sleep mode and the designated as TVREG, code execution is disabled. TVREG device can wake-up without waiting for TVREG. When is applied every time the device resumes operation after PMSLP is set, the power consumption while in Sleep any power-down, including Sleep mode. The length of mode, will be approximately 40 A higher than power TVREG is determined by the PMSLP bit (RCON<8>), as consumption when the regulator is allowed to enter described in Section25.2.5 “Voltage Regulator Standby mode. Standby Mode”. If the regulator is disabled, a separate Power-up Timer 25.3 Watchdog Timer (WDT) (PWRT) is automatically enabled. The PWRT adds a fixed delay of 64 ms nominal delay at device start-up For PIC24FJ256GA110 family devices, the WDT is (POR or BOR only). When waking up from Sleep with driven by the LPRC Oscillator. When the WDT is the regulator disabled, the PMSLP bit determines the enabled, the clock source is also enabled. wake-up time. When operating with the regulator The nominal WDT clock source from LPRC is 31kHz. disabled, setting PMSLP can decrease the device This feeds a prescaler that can be configured for either wake-up time. 5-bit (divide-by-32) or 7-bit (divide-by-128) operation. The prescaler is set by the FWPSA Configuration bit. 25.2.3 ON-CHIP REGULATOR AND BOR With a 31kHz input, the prescaler yields a nominal When the on-chip regulator is enabled, WDT time-out period (TWDT) of 1ms in 5-bit mode or PIC24FJ256GA110 family devices also have a simple 4ms in 7-bit mode. brown-out capability. If the voltage supplied to the reg- A variable postscaler divides down the WDT prescaler ulator is inadequate to maintain the tracking level, the output and allows for a wide range of time-out periods. regulator Reset circuitry will generate a Brown-out The postscaler is controlled by the WDTPS<3:0> Reset. This event is captured by the BOR flag bit Configuration bits (CW1<3:0>), which allow the selec- (RCON<1>). The brown-out voltage specifications are tion of a total of 16 settings, from 1:1 to 1:32,768. Using provided in the “PIC24FJ Family Reference Manual”, the prescaler and postscaler, time-out periods ranging Section 7. “Reset” (DS39712). from 1ms to 131 seconds can be achieved. 25.2.4 POWER-UP REQUIREMENTS The WDT, prescaler and postscaler are reset: The on-chip regulator is designed to meet the power-up • On any device Reset requirements for the device. If the application does not • On the completion of a clock switch, whether use the regulator, then strict power-up conditions must invoked by software (i.e., setting the OSWEN bit be adhered to. While powering up, VDDCORE must after changing the NOSC bits) or by hardware never exceed VDD by 0.3 volts. (i.e., Fail-Safe Clock Monitor) Note: For more information, see Section28.0 • When a PWRSAV instruction is executed (i.e., Sleep or Idle mode is entered) “Electrical Characteristics”. • When the device exits Sleep or Idle mode to 25.2.5 VOLTAGE REGULATOR STANDBY resume normal operation MODE • By a CLRWDT instruction during normal execution When enabled, the on-chip regulator always consumes If the WDT is enabled, it will continue to run during a small incremental amount of current over IDD/IPD, Sleep or Idle modes. When the WDT time-out occurs, including when the device is in Sleep mode, even the device will wake the device and code execution will though the core digital logic does not require power. To continue from where the PWRSAV instruction was exe- provide additional savings in applications where power cuted. The corresponding SLEEP or IDLE bits resources are critical, the regulator automatically (RCON<3:2>) will need to be cleared in software after disables itself whenever the device goes into Sleep the device wakes up. mode. This feature is controlled by the PMSLP bit The WDT Flag bit, WDTO (RCON<4>), is not auto- (RCON<8>). By default, the bit is cleared, which matically cleared following a WDT time-out. To detect removes power from the Flash program memory, and subsequent WDT events, the flag must be cleared in thus, enables Standby mode. When waking up from software. Standby mode, the regulator must wait for TVREG to expire before wake-up. This extra time is needed to Note: The CLRWDT and PWRSAV instructions ensure that the regulator can source enough current to clear the prescaler and postscaler counts power the Flash memory. when executed. DS39905E-page 252  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 25.3.1 WINDOWED OPERATION 25.3.2 CONTROL REGISTER The Watchdog Timer has an optional Fixed Window The WDT is enabled or disabled by the FWDTEN mode of operation. In this Windowed mode, CLRWDT Configuration bit. When the FWDTEN Configuration bit instructions can only reset the WDT during the last 1/4 is set, the WDT is always enabled. of the programmed WDT period. A CLRWDT instruction The WDT can be optionally controlled in software when executed before that window causes a WDT Reset, the FWDTEN Configuration bit has been programmed similar to a WDT time-out. to ‘0’. The WDT is enabled in software by setting the Windowed WDT mode is enabled by programming the SWDTEN control bit (RCON<5>). The SWDTEN WINDIS Configuration bit (CW1<6>) to ‘0’. control bit is cleared on any device Reset. The software WDT option allows the user to enable the WDT for critical code segments and disable the WDT during non-critical segments for maximum power savings. FIGURE 25-2: WDT BLOCK DIAGRAM SWDTEN LPRC Control FWDTEN Wake from Sleep FWPSA WDTPS<3:0> Prescaler WDT Postscaler LPRC Input (5-bit/7-bit) Counter 1:1 to 1:32.768 WDT Overflow Reset 31 kHz 1 ms/4 ms All Device Resets Transition to New Clock Source Exit Sleep or Idle Mode CLRWDT Instr. PWRSAV Instr. Sleep or Idle Mode 25.4 Program Verification and protection for this block is controlled by one Configura- Code Protection tion bit, GCP. This bit inhibits external reads and writes to the program memory space. It has no direct effect in PIC24FJ256GA110 family devices provide two normal execution mode. complimentary methods to protect application code Write protection is controlled by the GWRP bit in the from overwrites and erasures. These also help to Configuration Word. When GWRP is programmed to protect the device from inadvertent configuration ‘0’, internal write and erase operations to program changes during run time. memory are blocked. 25.4.1 GENERAL SEGMENT PROTECTION For all devices in the PIC24FJ256GA110 family, the on-chip program memory space is treated as a single block, known as the General Segment (GS). Code  2010 Microchip Technology Inc. DS39905E-page 253

PIC24FJ256GA110 FAMILY 25.4.2 CODE SEGMENT PROTECTION unprogrammed (= 1) protects the specified page through the last page of implemented program In addition to global General Segment protection, a memory, including the Configuration Word locations. separate subrange of the program memory space can be individually protected against writes and erases. A separate bit, WPCFG, is used to independently protect This area can be used for many purposes where a the last page of program space, including the Flash Con- separate block of erase and write-protected code is figuration Words. If WPEND is set to protect the bottom needed, such as bootloader applications. Unlike of program memory, programming WPCFG (= 0) pro- common boot block implementations, the specially pro- tects the last page. This may be useful in circumstances tected segment in the PIC24FJ256GA110 family where write protection is needed for both a code devices can be located by the user anywhere in the segment in the bottom of memory, as well as the Flash program space and configured in a wide range of sizes. Configuration Words. Code segment protection provides an added level of The various options for segment code protection are protection to a designated area of program memory by shown in Table25-2. disabling the NVM safety interlock whenever a write or 25.4.3 CONFIGURATION REGISTER erase address falls within a specified range. It does not override General Segment protection controlled by the PROTECTION GCP or GWRP bits. For example, if GCP and GWRP The Configuration registers are protected against are enabled, enabling segmented code protection for inadvertent or unwanted changes, or reads in two the bottom half of program memory does not undo ways. The primary protection method is the same as General Segment protection for the top half. that of the RP registers – shadow registers contain a The size and type of protection for the segmented code complimentary value which is constantly compared range are configured by the WPFPx, WPEND, WPCFG with the actual value. and WPDIS bits in Flash Configuration Word 3. Code To safeguard against unpredictable events, Configura- segment protection is enabled by programming the tion bit changes resulting from individual cell level WPDIS bit (= 0). The WPFP bits specify the size of the disruptions (such as ESD events) will cause a parity segment to be protected by specifying the 512-word error and trigger a device Reset. code page that is the start or end of the protected The data for the Configuration registers is derived from segment. The specified region is inclusive, therefore, the Flash Configuration Words in program memory. this page will also be protected. When the GCP bit is set, the source data for device The WPEND bit determines if the protected segment configuration is also protected as a consequence. Even uses the top or bottom of the program space as a if General Segment protection is not enabled, the boundary. Programming WPEND (= 0) sets the bottom device configuration can be protected by using the of program memory (000000h) as the lower boundary appropriate code segment protection setting. of the protected segment. Leaving WPEND TABLE 25-2: SEGMENT CODE PROTECTION CONFIGURATION OPTIONS Segment Configuration Bits Write/Erase Protection of Code Segment WPDIS WPEND WPCFG 1 x x No additional protection enabled; all program memory protection is configured by GCP and GWRP 0 1 x Addresses from the first address of code page, defined by WPFP<7:0> through the end of implemented program memory (inclusive), are write/erase protected including Flash Configuration Words 0 0 1 Address, 000000h through the last address of code page, defined by WPFP<7:0> (inclusive), is protected 0 0 0 Address, 000000h through the last address of code page, defined by WPFP<7:0> (inclusive) are write/erase protected and the last page is also write/erase protected. DS39905E-page 254  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 25.5 JTAG Interface 25.7 In-Circuit Debugger PIC24FJ256GA110 family devices implement a JTAG When MPLAB® ICD 2 is selected as a debugger, the interface, which supports boundary scan device in-circuit debugging functionality is enabled. This func- testing. tion allows simple debugging functions when used with MPLAB IDE. Debugging functionality is controlled 25.6 In-Circuit Serial Programming through the PGECx (Emulation/Debug Clock) and PGEDx (Emulation/Debug Data) pins. PIC24FJ256GA110 family microcontrollers can be seri- To use the in-circuit debugger function of the device, ally programmed while in the end application circuit. the design must implement ICSP connections to This is simply done with two lines for clock (PGECx) MCLR, VDD, VSS and the PGECx/PGEDx pin pair des- and data (PGEDx), and three other lines for power, ignated by the ICS Configuration bits. In addition, when ground and the programming voltage. This allows the feature is enabled, some of the resources are not customers to manufacture boards with unprogrammed available for general use. These resources include the devices and then program the microcontroller just first 80 bytes of data RAM and two I/O pins. before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed.  2010 Microchip Technology Inc. DS39905E-page 255

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 256  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 26.0 INSTRUCTION SET SUMMARY The literal instructions that involve data movement may use some of the following operands: Note: This chapter is a brief summary of the • A literal value to be loaded into a W register or file PIC24F instruction set architecture, and is register (specified by the value of ‘k’) not intended to be a comprehensive • The W register or file register where the literal reference source. value is to be loaded (specified by ‘Wb’ or ‘f’) The PIC24F instruction set adds many enhancements However, literal instructions that involve arithmetic or to the previous PIC® MCU instruction sets, while main- logical operations use some of the following operands: taining an easy migration from previous PIC MCU • The first source operand, which is a register, ‘Wb’, instruction sets. Most instructions are a single program without any address modifier memory word. Only three instructions require two program memory locations. • The second source operand, which is a literal value Each single-word instruction is a 24-bit word divided • The destination of the result (only if not the same into an 8-bit opcode, which specifies the instruction as the first source operand), which is typically a type and one or more operands, which further specify register ‘Wd’ with or without an address modifier the operation of the instruction. The instruction set is highly orthogonal and is grouped into four basic The control instructions may use some of the following categories: operands: • Word or byte-oriented operations • A program memory address • Bit-oriented operations • The mode of the table read and table write • Literal operations instructions • Control operations All instructions are a single word, except for certain double-word instructions, which were made Table26-1 shows the general symbols used in double-word instructions so that all the required infor- describing the instructions. The PIC24F instruction set mation is available in these 48 bits. In the second word, summary in Table26-2 lists all of the instructions, along the 8MSbs are ‘0’s. If this second word is executed as with the status flags affected by each instruction. an instruction (by itself), it will execute as a NOP. Most word or byte-oriented W register instructions Most single-word instructions are executed in a single (including barrel shift instructions) have three instruction cycle, unless a conditional test is true or the operands: program counter is changed as a result of the instruc- • The first source operand, which is typically a tion. In these cases, the execution takes two instruction register, ‘Wb’, without any address modifier cycles, with the additional instruction cycle(s) executed • The second source operand, which is typically a as a NOP. Notable exceptions are the BRA (uncondi- register, ‘Ws’, with or without an address modifier tional/computed branch), indirect CALL/GOTO, all table • The destination of the result, which is typically a reads and writes, and RETURN/RETFIE instructions, registe,r ‘Wd’, with or without an address modifier which are single-word instructions but take two or three cycles. However, word or byte-oriented file register instructions have two operands: Certain instructions that involve skipping over the sub- sequent instruction require either two or three cycles if • The file register specified by the value, ‘f’ the skip is performed, depending on whether the • The destination, which could either be the file instruction being skipped is a single-word or two-word register, ‘f’, or the W0 register, which is denoted instruction. Moreover, double-word moves require two as ‘WREG’ cycles. The double-word instructions execute in two Most bit-oriented instructions (including simple instruction cycles. rotate/shift instructions) have two operands: • The W register (with or without an address modifier) or file register (specified by the value of ‘Ws’ or ‘f’) • The bit in the W register or file register (specified by a literal value or indirectly by the contents of register, ‘Wb’)  2010 Microchip Technology Inc. DS39905E-page 257

PIC24FJ256GA110 FAMILY TABLE 26-1: SYMBOLS USED IN OPCODE DESCRIPTIONS Field Description #text Means literal defined by “text” (text) Means “content of text” [text] Means “the location addressed by text” { } Optional field or operation <n:m> Register bit field .b Byte mode selection .d Double-Word mode selection .S Shadow register select .w Word mode selection (default) bit4 4-bit bit selection field (used in word addressed instructions) {0...15} C, DC, N, OV, Z MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero Expr Absolute address, label or expression (resolved by the linker) f File register address {0000h...1FFFh} lit1 1-bit unsigned literal {0,1} lit4 4-bit unsigned literal {0...15} lit5 5-bit unsigned literal {0...31} lit8 8-bit unsigned literal {0...255} lit10 10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode lit14 14-bit unsigned literal {0...16384} lit16 16-bit unsigned literal {0...65535} lit23 23-bit unsigned literal {0...8388608}; LSB must be ‘0’ None Field does not require an entry, may be blank PC Program Counter Slit10 10-bit signed literal {-512...511} Slit16 16-bit signed literal {-32768...32767} Slit6 6-bit signed literal {-16...16} Wb Base W register {W0..W15} Wd Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] } Wdo Destination W register  { Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] } Wm,Wn Dividend, Divisor working register pair (direct addressing) Wn One of 16 working registers {W0..W15} Wnd One of 16 destination working registers {W0..W15} Wns One of 16 source working registers {W0..W15} WREG W0 (working register used in file register instructions) Ws Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] } Wso Source W register { Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] } DS39905E-page 258  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 26-2: INSTRUCTION SET OVERVIEW Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected ADD ADD f f = f + WREG 1 1 C, DC, N, OV, Z ADD f,WREG WREG = f + WREG 1 1 C, DC, N, OV, Z ADD #lit10,Wn Wd = lit10 + Wd 1 1 C, DC, N, OV, Z ADD Wb,Ws,Wd Wd = Wb + Ws 1 1 C, DC, N, OV, Z ADD Wb,#lit5,Wd Wd = Wb + lit5 1 1 C, DC, N, OV, Z ADDC ADDC f f = f + WREG + (C) 1 1 C, DC, N, OV, Z ADDC f,WREG WREG = f + WREG + (C) 1 1 C, DC, N, OV, Z ADDC #lit10,Wn Wd = lit10 + Wd + (C) 1 1 C, DC, N, OV, Z ADDC Wb,Ws,Wd Wd = Wb + Ws + (C) 1 1 C, DC, N, OV, Z ADDC Wb,#lit5,Wd Wd = Wb + lit5 + (C) 1 1 C, DC, N, OV, Z AND AND f f = f .AND. WREG 1 1 N, Z AND f,WREG WREG = f .AND. WREG 1 1 N, Z AND #lit10,Wn Wd = lit10 .AND. Wd 1 1 N, Z AND Wb,Ws,Wd Wd = Wb .AND. Ws 1 1 N, Z AND Wb,#lit5,Wd Wd = Wb .AND. lit5 1 1 N, Z ASR ASR f f = Arithmetic Right Shift f 1 1 C, N, OV, Z ASR f,WREG WREG = Arithmetic Right Shift f 1 1 C, N, OV, Z ASR Ws,Wd Wd = Arithmetic Right Shift Ws 1 1 C, N, OV, Z ASR Wb,Wns,Wnd Wnd = Arithmetic Right Shift Wb by Wns 1 1 N, Z ASR Wb,#lit5,Wnd Wnd = Arithmetic Right Shift Wb by lit5 1 1 N, Z BCLR BCLR f,#bit4 Bit Clear f 1 1 None BCLR Ws,#bit4 Bit Clear Ws 1 1 None BRA BRA C,Expr Branch if Carry 1 1 (2) None BRA GE,Expr Branch if Greater than or Equal 1 1 (2) None BRA GEU,Expr Branch if Unsigned Greater than or Equal 1 1 (2) None BRA GT,Expr Branch if Greater than 1 1 (2) None BRA GTU,Expr Branch if Unsigned Greater than 1 1 (2) None BRA LE,Expr Branch if Less than or Equal 1 1 (2) None BRA LEU,Expr Branch if Unsigned Less than or Equal 1 1 (2) None BRA LT,Expr Branch if Less than 1 1 (2) None BRA LTU,Expr Branch if Unsigned Less than 1 1 (2) None BRA N,Expr Branch if Negative 1 1 (2) None BRA NC,Expr Branch if Not Carry 1 1 (2) None BRA NN,Expr Branch if Not Negative 1 1 (2) None BRA NOV,Expr Branch if Not Overflow 1 1 (2) None BRA NZ,Expr Branch if Not Zero 1 1 (2) None BRA OV,Expr Branch if Overflow 1 1 (2) None BRA Expr Branch Unconditionally 1 2 None BRA Z,Expr Branch if Zero 1 1 (2) None BRA Wn Computed Branch 1 2 None BSET BSET f,#bit4 Bit Set f 1 1 None BSET Ws,#bit4 Bit Set Ws 1 1 None BSW BSW.C Ws,Wb Write C bit to Ws<Wb> 1 1 None BSW.Z Ws,Wb Write Z bit to Ws<Wb> 1 1 None BTG BTG f,#bit4 Bit Toggle f 1 1 None BTG Ws,#bit4 Bit Toggle Ws 1 1 None BTSC BTSC f,#bit4 Bit Test f, Skip if Clear 1 1 None (2 or 3) BTSC Ws,#bit4 Bit Test Ws, Skip if Clear 1 1 None (2 or 3)  2010 Microchip Technology Inc. DS39905E-page 259

PIC24FJ256GA110 FAMILY TABLE 26-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected BTSS BTSS f,#bit4 Bit Test f, Skip if Set 1 1 None (2 or 3) BTSS Ws,#bit4 Bit Test Ws, Skip if Set 1 1 None (2 or 3) BTST BTST f,#bit4 Bit Test f 1 1 Z BTST.C Ws,#bit4 Bit Test Ws to C 1 1 C BTST.Z Ws,#bit4 Bit Test Ws to Z 1 1 Z BTST.C Ws,Wb Bit Test Ws<Wb> to C 1 1 C BTST.Z Ws,Wb Bit Test Ws<Wb> to Z 1 1 Z BTSTS BTSTS f,#bit4 Bit Test then Set f 1 1 Z BTSTS.C Ws,#bit4 Bit Test Ws to C, then Set 1 1 C BTSTS.Z Ws,#bit4 Bit Test Ws to Z, then Set 1 1 Z CALL CALL lit23 Call Subroutine 2 2 None CALL Wn Call Indirect Subroutine 1 2 None CLR CLR f f = 0x0000 1 1 None CLR WREG WREG = 0x0000 1 1 None CLR Ws Ws = 0x0000 1 1 None CLRWDT CLRWDT Clear Watchdog Timer 1 1 WDTO, Sleep COM COM f f = f 1 1 N, Z COM f,WREG WREG = f 1 1 N, Z COM Ws,Wd Wd = Ws 1 1 N, Z CP CP f Compare f with WREG 1 1 C, DC, N, OV, Z CP Wb,#lit5 Compare Wb with lit5 1 1 C, DC, N, OV, Z CP Wb,Ws Compare Wb with Ws (Wb – Ws) 1 1 C, DC, N, OV, Z CP0 CP0 f Compare f with 0x0000 1 1 C, DC, N, OV, Z CP0 Ws Compare Ws with 0x0000 1 1 C, DC, N, OV, Z CPB CPB f Compare f with WREG, with Borrow 1 1 C, DC, N, OV, Z CPB Wb,#lit5 Compare Wb with lit5, with Borrow 1 1 C, DC, N, OV, Z CPB Wb,Ws Compare Wb with Ws, with Borrow 1 1 C, DC, N, OV, Z (Wb – Ws – C) CPSEQ CPSEQ Wb,Wn Compare Wb with Wn, Skip if = 1 1 None (2 or 3) CPSGT CPSGT Wb,Wn Compare Wb with Wn, Skip if > 1 1 None (2 or 3) CPSLT CPSLT Wb,Wn Compare Wb with Wn, Skip if < 1 1 None (2 or 3) CPSNE CPSNE Wb,Wn Compare Wb with Wn, Skip if  1 1 None (2 or 3) DAW DAW.b Wn Wn = Decimal Adjust Wn 1 1 C DEC DEC f f = f – 1 1 1 C, DC, N, OV, Z DEC f,WREG WREG = f – 1 1 1 C, DC, N, OV, Z DEC Ws,Wd Wd = Ws – 1 1 1 C, DC, N, OV, Z DEC2 DEC2 f f = f – 2 1 1 C, DC, N, OV, Z DEC2 f,WREG WREG = f – 2 1 1 C, DC, N, OV, Z DEC2 Ws,Wd Wd = Ws – 2 1 1 C, DC, N, OV, Z DISI DISI #lit14 Disable Interrupts for k Instruction Cycles 1 1 None DIV DIV.SW Wm,Wn Signed 16/16-bit Integer Divide 1 18 N, Z, C, OV DIV.SD Wm,Wn Signed 32/16-bit Integer Divide 1 18 N, Z, C, OV DIV.UW Wm,Wn Unsigned 16/16-bit Integer Divide 1 18 N, Z, C, OV DIV.UD Wm,Wn Unsigned 32/16-bit Integer Divide 1 18 N, Z, C, OV EXCH EXCH Wns,Wnd Swap Wns with Wnd 1 1 None FF1L FF1L Ws,Wnd Find First One from Left (MSb) Side 1 1 C FF1R FF1R Ws,Wnd Find First One from Right (LSb) Side 1 1 C DS39905E-page 260  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 26-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected GOTO GOTO Expr Go to Address 2 2 None GOTO Wn Go to Indirect 1 2 None INC INC f f = f + 1 1 1 C, DC, N, OV, Z INC f,WREG WREG = f + 1 1 1 C, DC, N, OV, Z INC Ws,Wd Wd = Ws + 1 1 1 C, DC, N, OV, Z INC2 INC2 f f = f + 2 1 1 C, DC, N, OV, Z INC2 f,WREG WREG = f + 2 1 1 C, DC, N, OV, Z INC2 Ws,Wd Wd = Ws + 2 1 1 C, DC, N, OV, Z IOR IOR f f = f .IOR. WREG 1 1 N, Z IOR f,WREG WREG = f .IOR. WREG 1 1 N, Z IOR #lit10,Wn Wd = lit10 .IOR. Wd 1 1 N, Z IOR Wb,Ws,Wd Wd = Wb .IOR. Ws 1 1 N, Z IOR Wb,#lit5,Wd Wd = Wb .IOR. lit5 1 1 N, Z LNK LNK #lit14 Link Frame Pointer 1 1 None LSR LSR f f = Logical Right Shift f 1 1 C, N, OV, Z LSR f,WREG WREG = Logical Right Shift f 1 1 C, N, OV, Z LSR Ws,Wd Wd = Logical Right Shift Ws 1 1 C, N, OV, Z LSR Wb,Wns,Wnd Wnd = Logical Right Shift Wb by Wns 1 1 N, Z LSR Wb,#lit5,Wnd Wnd = Logical Right Shift Wb by lit5 1 1 N, Z MOV MOV f,Wn Move f to Wn 1 1 None MOV [Wns+Slit10],Wnd Move [Wns+Slit10] to Wnd 1 1 None MOV f Move f to f 1 1 N, Z MOV f,WREG Move f to WREG 1 1 N, Z MOV #lit16,Wn Move 16-bit Literal to Wn 1 1 None MOV.b #lit8,Wn Move 8-bit Literal to Wn 1 1 None MOV Wn,f Move Wn to f 1 1 None MOV Wns,[Wns+Slit10] Move Wns to [Wns+Slit10] 1 1 MOV Wso,Wdo Move Ws to Wd 1 1 None MOV WREG,f Move WREG to f 1 1 N, Z MOV.D Wns,Wd Move Double from W(ns):W(ns + 1) to Wd 1 2 None MOV.D Ws,Wnd Move Double from Ws to W(nd + 1):W(nd) 1 2 None MUL MUL.SS Wb,Ws,Wnd {Wnd + 1, Wnd} = Signed(Wb) * Signed(Ws) 1 1 None MUL.SU Wb,Ws,Wnd {Wnd + 1, Wnd} = Signed(Wb) * Unsigned(Ws) 1 1 None MUL.US Wb,Ws,Wnd {Wnd + 1, Wnd} = Unsigned(Wb) * Signed(Ws) 1 1 None MUL.UU Wb,Ws,Wnd {Wnd + 1, Wnd} = Unsigned(Wb) * Unsigned(Ws) 1 1 None MUL.SU Wb,#lit5,Wnd {Wnd + 1, Wnd} = Signed(Wb) * Unsigned(lit5) 1 1 None MUL.UU Wb,#lit5,Wnd {Wnd + 1, Wnd} = Unsigned(Wb) * Unsigned(lit5) 1 1 None MUL f W3:W2 = f * WREG 1 1 None NEG NEG f f = f + 1 1 1 C, DC, N, OV, Z NEG f,WREG WREG = f + 1 1 1 C, DC, N, OV, Z NEG Ws,Wd Wd = Ws + 1 1 1 C, DC, N, OV, Z NOP NOP No Operation 1 1 None NOPR No Operation 1 1 None POP POP f Pop f from Top-of-Stack (TOS) 1 1 None POP Wdo Pop from Top-of-Stack (TOS) to Wdo 1 1 None POP.D Wnd Pop from Top-of-Stack (TOS) to W(nd):W(nd + 1) 1 2 None POP.S Pop Shadow Registers 1 1 All PUSH PUSH f Push f to Top-of-Stack (TOS) 1 1 None PUSH Wso Push Wso to Top-of-Stack (TOS) 1 1 None PUSH.D Wns Push W(ns):W(ns + 1) to Top-of-Stack (TOS) 1 2 None PUSH.S Push Shadow Registers 1 1 None  2010 Microchip Technology Inc. DS39905E-page 261

PIC24FJ256GA110 FAMILY TABLE 26-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected PWRSAV PWRSAV #lit1 Go into Sleep or Idle mode 1 1 WDTO, Sleep RCALL RCALL Expr Relative Call 1 2 None RCALL Wn Computed Call 1 2 None REPEAT REPEAT #lit14 Repeat Next Instruction lit14 + 1 times 1 1 None REPEAT Wn Repeat Next Instruction (Wn) + 1 times 1 1 None RESET RESET Software Device Reset 1 1 None RETFIE RETFIE Return from Interrupt 1 3 (2) None RETLW RETLW #lit10,Wn Return with Literal in Wn 1 3 (2) None RETURN RETURN Return from Subroutine 1 3 (2) None RLC RLC f f = Rotate Left through Carry f 1 1 C, N, Z RLC f,WREG WREG = Rotate Left through Carry f 1 1 C, N, Z RLC Ws,Wd Wd = Rotate Left through Carry Ws 1 1 C, N, Z RLNC RLNC f f = Rotate Left (No Carry) f 1 1 N, Z RLNC f,WREG WREG = Rotate Left (No Carry) f 1 1 N, Z RLNC Ws,Wd Wd = Rotate Left (No Carry) Ws 1 1 N, Z RRC RRC f f = Rotate Right through Carry f 1 1 C, N, Z RRC f,WREG WREG = Rotate Right through Carry f 1 1 C, N, Z RRC Ws,Wd Wd = Rotate Right through Carry Ws 1 1 C, N, Z RRNC RRNC f f = Rotate Right (No Carry) f 1 1 N, Z RRNC f,WREG WREG = Rotate Right (No Carry) f 1 1 N, Z RRNC Ws,Wd Wd = Rotate Right (No Carry) Ws 1 1 N, Z SE SE Ws,Wnd Wnd = Sign-Extended Ws 1 1 C, N, Z SETM SETM f f = FFFFh 1 1 None SETM WREG WREG = FFFFh 1 1 None SETM Ws Ws = FFFFh 1 1 None SL SL f f = Left Shift f 1 1 C, N, OV, Z SL f,WREG WREG = Left Shift f 1 1 C, N, OV, Z SL Ws,Wd Wd = Left Shift Ws 1 1 C, N, OV, Z SL Wb,Wns,Wnd Wnd = Left Shift Wb by Wns 1 1 N, Z SL Wb,#lit5,Wnd Wnd = Left Shift Wb by lit5 1 1 N, Z SUB SUB f f = f – WREG 1 1 C, DC, N, OV, Z SUB f,WREG WREG = f – WREG 1 1 C, DC, N, OV, Z SUB #lit10,Wn Wn = Wn – lit10 1 1 C, DC, N, OV, Z SUB Wb,Ws,Wd Wd = Wb – Ws 1 1 C, DC, N, OV, Z SUB Wb,#lit5,Wd Wd = Wb – lit5 1 1 C, DC, N, OV, Z SUBB SUBB f f = f – WREG – (C) 1 1 C, DC, N, OV, Z SUBB f,WREG WREG = f – WREG – (C) 1 1 C, DC, N, OV, Z SUBB #lit10,Wn Wn = Wn – lit10 – (C) 1 1 C, DC, N, OV, Z SUBB Wb,Ws,Wd Wd = Wb – Ws – (C) 1 1 C, DC, N, OV, Z SUBB Wb,#lit5,Wd Wd = Wb – lit5 – (C) 1 1 C, DC, N, OV, Z SUBR SUBR f f = WREG – f 1 1 C, DC, N, OV, Z SUBR f,WREG WREG = WREG – f 1 1 C, DC, N, OV, Z SUBR Wb,Ws,Wd Wd = Ws – Wb 1 1 C, DC, N, OV, Z SUBR Wb,#lit5,Wd Wd = lit5 – Wb 1 1 C, DC, N, OV, Z SUBBR SUBBR f f = WREG – f – (C) 1 1 C, DC, N, OV, Z SUBBR f,WREG WREG = WREG – f – (C) 1 1 C, DC, N, OV, Z SUBBR Wb,Ws,Wd Wd = Ws – Wb – (C) 1 1 C, DC, N, OV, Z SUBBR Wb,#lit5,Wd Wd = lit5 – Wb – (C) 1 1 C, DC, N, OV, Z SWAP SWAP.b Wn Wn = Nibble Swap Wn 1 1 None SWAP Wn Wn = Byte Swap Wn 1 1 None DS39905E-page 262  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 26-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected TBLRDH TBLRDH Ws,Wd Read Prog<23:16> to Wd<7:0> 1 2 None TBLRDL TBLRDL Ws,Wd Read Prog<15:0> to Wd 1 2 None TBLWTH TBLWTH Ws,Wd Write Ws<7:0> to Prog<23:16> 1 2 None TBLWTL TBLWTL Ws,Wd Write Ws to Prog<15:0> 1 2 None ULNK ULNK Unlink Frame Pointer 1 1 None XOR XOR f f = f .XOR. WREG 1 1 N, Z XOR f,WREG WREG = f .XOR. WREG 1 1 N, Z XOR #lit10,Wn Wd = lit10 .XOR. Wd 1 1 N, Z XOR Wb,Ws,Wd Wd = Wb .XOR. Ws 1 1 N, Z XOR Wb,#lit5,Wd Wd = Wb .XOR. lit5 1 1 N, Z ZE ZE Ws,Wnd Wnd = Zero-Extend Ws 1 1 C, Z, N  2010 Microchip Technology Inc. DS39905E-page 263

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 264  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 27.0 DEVELOPMENT SUPPORT 27.1 MPLAB Integrated Development Environment Software The PIC® microcontrollers and dsPIC® digital signal controllers are supported with a full range of software The MPLAB IDE software brings an ease of software and hardware development tools: development previously unseen in the 8/16/32-bit • Integrated Development Environment microcontroller market. The MPLAB IDE is a Windows® operating system-based application that contains: - MPLAB® IDE Software • Compilers/Assemblers/Linkers • A single graphical interface to all debugging tools - MPLAB C Compiler for Various Device - Simulator Families - Programmer (sold separately) - HI-TECH C for Various Device Families - In-Circuit Emulator (sold separately) - MPASMTM Assembler - In-Circuit Debugger (sold separately) - MPLINKTM Object Linker/ • A full-featured editor with color-coded context MPLIBTM Object Librarian • A multiple project manager - MPLAB Assembler/Linker/Librarian for • Customizable data windows with direct edit of Various Device Families contents • Simulators • High-level source code debugging - MPLAB SIM Software Simulator • Mouse over variable inspection • Emulators • Drag and drop variables from source to watch - MPLAB REAL ICE™ In-Circuit Emulator windows • In-Circuit Debuggers • Extensive on-line help - MPLAB ICD 3 • Integration of select third party tools, such as - PICkit™ 3 Debug Express IAR C Compilers • Device Programmers The MPLAB IDE allows you to: - PICkit™ 2 Programmer • Edit your source files (either C or assembly) - MPLAB PM3 Device Programmer • One-touch compile or assemble, and download to • Low-Cost Demonstration/Development Boards, emulator and simulator tools (automatically Evaluation Kits, and Starter Kits updates all project information) • Debug using: - Source files (C or assembly) - Mixed C and assembly - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power.  2010 Microchip Technology Inc. DS39905E-page 265

PIC24FJ256GA110 FAMILY 27.2 MPLAB C Compilers for Various 27.5 MPLINK Object Linker/ Device Families MPLIB Object Librarian The MPLAB C Compiler code development systems The MPLINK Object Linker combines relocatable are complete ANSI C compilers for Microchip’s PIC18, objects created by the MPASM Assembler and the PIC24 and PIC32 families of microcontrollers and the MPLAB C18 C Compiler. It can link relocatable objects dsPIC30 and dsPIC33 families of digital signal control- from precompiled libraries, using directives from a lers. These compilers provide powerful integration linker script. capabilities, superior code optimization and ease of The MPLIB Object Librarian manages the creation and use. modification of library files of precompiled code. When For easy source level debugging, the compilers provide a routine from a library is called from a source file, only symbol information that is optimized to the MPLAB IDE the modules that contain that routine will be linked in debugger. with the application. This allows large libraries to be used efficiently in many different applications. 27.3 HI-TECH C for Various Device The object linker/library features include: Families • Efficient linking of single libraries instead of many The HI-TECH C Compiler code development systems smaller files are complete ANSI C compilers for Microchip’s PIC • Enhanced code maintainability by grouping family of microcontrollers and the dsPIC family of digital related modules together signal controllers. These compilers provide powerful • Flexible creation of libraries with easy module integration capabilities, omniscient code generation listing, replacement, deletion and extraction and ease of use. For easy source level debugging, the compilers provide 27.6 MPLAB Assembler, Linker and symbol information that is optimized to the MPLAB IDE Librarian for Various Device debugger. Families The compilers include a macro assembler, linker, pre- MPLAB Assembler produces relocatable machine processor, and one-step driver, and can run on multiple code from symbolic assembly language for PIC24, platforms. PIC32 and dsPIC devices. MPLAB C Compiler uses the assembler to produce its object file. The assembler 27.4 MPASM Assembler generates relocatable object files that can then be The MPASM Assembler is a full-featured, universal archived or linked with other relocatable object files and macro assembler for PIC10/12/16/18 MCUs. archives to create an executable file. Notable features of the assembler include: The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel® standard HEX • Support for the entire device instruction set files, MAP files to detail memory usage and symbol • Support for fixed-point and floating-point data reference, absolute LST files that contain source lines • Command line interface and generated machine code and COFF files for • Rich directive set debugging. • Flexible macro language The MPASM Assembler features include: • MPLAB IDE compatibility • Integration into MPLAB IDE projects • User-defined macros to streamline assembly code • Conditional assembly for multi-purpose source files • Directives that allow complete control over the assembly process DS39905E-page 266  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 27.7 MPLAB SIM Software Simulator 27.9 MPLAB ICD 3 In-Circuit Debugger System The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulat- MPLAB ICD 3 In-Circuit Debugger System is Micro- ing the PIC MCUs and dsPIC® DSCs on an instruction chip's most cost effective high-speed hardware level. On any given instruction, the data areas can be debugger/programmer for Microchip Flash Digital Sig- examined or modified and stimuli can be applied from nal Controller (DSC) and microcontroller (MCU) a comprehensive stimulus controller. Registers can be devices. It debugs and programs PIC® Flash microcon- logged to files for further run-time analysis. The trace trollers and dsPIC® DSCs with the powerful, yet easy- buffer and logic analyzer display extend the power of to-use graphical user interface of MPLAB Integrated the simulator to record and track program execution, Development Environment (IDE). actions on I/O, most peripherals and internal registers. The MPLAB ICD 3 In-Circuit Debugger probe is con- The MPLAB SIM Software Simulator fully supports nected to the design engineer's PC using a high-speed symbolic debugging using the MPLAB CCompilers, USB 2.0 interface and is connected to the target with a and the MPASM and MPLAB Assemblers. The soft- connector compatible with the MPLAB ICD 2 or MPLAB ware simulator offers the flexibility to develop and REAL ICE systems (RJ-11). MPLAB ICD 3 supports all debug code outside of the hardware laboratory envi- MPLAB ICD 2 headers. ronment, making it an excellent, economical software development tool. 27.10 PICkit 3 In-Circuit Debugger/ Programmer and 27.8 MPLAB REAL ICE In-Circuit PICkit 3 Debug Express Emulator System The MPLAB PICkit 3 allows debugging and program- MPLAB REAL ICE In-Circuit Emulator System is ming of PIC® and dsPIC® Flash microcontrollers at a Microchip’s next generation high-speed emulator for most affordable price point using the powerful graphical Microchip Flash DSC and MCU devices. It debugs and user interface of the MPLAB Integrated Development programs PIC® Flash MCUs and dsPIC® Flash DSCs Environment (IDE). The MPLAB PICkit 3 is connected with the easy-to-use, powerful graphical user interface of to the design engineer's PC using a full speed USB the MPLAB Integrated Development Environment (IDE), interface and can be connected to the target via an included with each kit. Microchip debug (RJ-11) connector (compatible with The emulator is connected to the design engineer’s PC MPLAB ICD 3 and MPLAB REAL ICE). The connector using a high-speed USB 2.0 interface and is connected uses two device I/O pins and the reset line to imple- to the target with either a connector compatible with in- ment in-circuit debugging and In-Circuit Serial Pro- circuit debugger systems (RJ11) or with the new high- gramming™. speed, noise tolerant, Low-Voltage Differential Signal The PICkit 3 Debug Express include the PICkit 3, demo (LVDS) interconnection (CAT5). board and microcontroller, hookup cables and CDROM The emulator is field upgradable through future firmware with user’s guide, lessons, tutorial, compiler and downloads in MPLAB IDE. In upcoming releases of MPLAB IDE software. MPLAB IDE, new devices will be supported, and new features will be added. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, run-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables.  2010 Microchip Technology Inc. DS39905E-page 267

PIC24FJ256GA110 FAMILY 27.11 PICkit 2 Development 27.13 Demonstration/Development Programmer/Debugger and Boards, Evaluation Kits, and PICkit 2 Debug Express Starter Kits The PICkit™ 2 Development Programmer/Debugger is A wide variety of demonstration, development and a low-cost development tool with an easy to use inter- evaluation boards for various PIC MCUs and dsPIC face for programming and debugging Microchip’s Flash DSCs allows quick application development on fully func- families of microcontrollers. The full featured tional systems. Most boards include prototyping areas for Windows® programming interface supports baseline adding custom circuitry and provide application firmware (PIC10F, PIC12F5xx, PIC16F5xx), midrange and source code for examination and modification. (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, The boards support a variety of features, including LEDs, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit temperature sensors, switches, speakers, RS-232 microcontrollers, and many Microchip Serial EEPROM interfaces, LCD displays, potentiometers and additional products. With Microchip’s powerful MPLAB Integrated EEPROM memory. Development Environment (IDE) the PICkit™ 2 enables in-circuit debugging on most PIC® microcon- The demonstration and development boards can be trollers. In-Circuit-Debugging runs, halts and single used in teaching environments, for prototyping custom steps the program while the PIC microcontroller is circuits and for learning about various microcontroller embedded in the application. When halted at a break- applications. point, the file registers can be examined and modified. In addition to the PICDEM™ and dsPICDEM™ demon- The PICkit 2 Debug Express include the PICkit 2, demo stration/development board series of circuits, Microchip board and microcontroller, hookup cables and CDROM has a line of evaluation kits and demonstration software with user’s guide, lessons, tutorial, compiler and for analog filter design, KEELOQ® security ICs, CAN, IrDA®, PowerSmart battery management, SEEVAL® MPLAB IDE software. evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. 27.12 MPLAB PM3 Device Programmer Also available are starter kits that contain everything The MPLAB PM3 Device Programmer is a universal, needed to experience the specified device. This usually CE compliant device programmer with programmable includes a single application and debug capability, all voltage verification at VDDMIN and VDDMAX for on one board. maximum reliability. It features a large LCD display Check the Microchip web page (www.microchip.com) (128 x 64) for menus and error messages and a modu- for the complete list of demonstration, development lar, detachable socket assembly to support various and evaluation kits. package types. The ICSP™ cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an MMC card for file storage and data applications. DS39905E-page 268  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 28.0 ELECTRICAL CHARACTERISTICS This section provides an overview of the PIC24FJ256GA110 family electrical characteristics. Additional information will be provided in future revisions of this document as it becomes available. Absolute maximum ratings for the PIC24FJ256GA110 family are listed below. Exposure to these maximum rating conditions for extended periods may affect device reliability. Functional operation of the device at these, or any other conditions above the parameters indicated in the operation listings of this specification, is not implied. Absolute Maximum Ratings(†) Ambient temperature under bias.............................................................................................................-40°C to +100°C Storage temperature.............................................................................................................................. -65°C to +150°C Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V Voltage on any combined analog and digital pin and MCLR, with respect to VSS .........................-0.3V to (VDD + 0.3V) Voltage on any digital only pin with respect to VSS .................................................................................. -0.3V to +6.0V Voltage on VDDCORE with respect to VSS ................................................................................................. -0.3V to +3.0V Maximum current out of VSS pin...........................................................................................................................300 mA Maximum current into VDD pin (Note 1)................................................................................................................250 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin....................................................................................................25 mA Maximum current sunk by all ports.......................................................................................................................200 mA Maximum current sourced by all ports (Note 1)....................................................................................................200 mA Note1: Maximum allowable current is a function of device maximum power dissipation (see Table28-1). †NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.  2010 Microchip Technology Inc. DS39905E-page 269

PIC24FJ256GA110 FAMILY 28.1 DC Characteristics FIGURE 28-1: PIC24FJ256GA110 FAMILY VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL) 3.00V 2.75V 2.75V 1) ()E 2.50V PIC24FJXXXGA1XX R O DC 2.25V 2.25V D V ( e 2.00V g a t ol V 16 MHz 32 MHz Frequency For frequencies between 16MHz and 32MHz, FMAX = (64MHz/V) * (VDDCORE – 2V) + 16MHz. Note 1: When the voltage regulator is disabled, VDD and VDDCORE must be maintained so that VDDCOREVDD3.6V. TABLE 28-1: THERMAL OPERATING CONDITIONS Rating Symbol Min Typ Max Unit PIC24FJ256GA110 Family: Operating Junction Temperature Range TJ -40 — +140 °C Operating Ambient Temperature Range TA -40 — +125 °C Power Dissipation: Internal Chip Power Dissipation: PINT = VDD x (IDD –  IOH) PD PINT + PI/O W I/O Pin Power Dissipation: PI/O =  ({VDD – VOH} x IOH) +  (VOL x IOL) Maximum Allowed Power Dissipation PDMAX (TJ – TA)/JA W TABLE 28-2: THERMAL PACKAGING CHARACTERISTICS Characteristic Symbol Typ Max Unit Notes Package Thermal Resistance, 14x14x1 mm TQFP JA 50.0 — °C/W (Note 1) Package Thermal Resistance, 12x12x1 mm TQFP JA 69.4 — °C/W (Note 1) Package Thermal Resistance, 10x10x1 mm TQFP JA 76.6 — °C/W (Note 1) Package Thermal Resistance, 9x9x0.9 mm QFN JA 28.0 — °C/W (Note 1) Note 1: Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations. DS39905E-page 270  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 28-3: DC CHARACTERISTICS: TEMPERATURE AND VOLTAGE SPECIFICATIONS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min Typ(1) Max Units Conditions No. Operating Voltage DC10 Supply Voltage VDD VBOR — 3.6 V Regulator enabled VDD VDDCORE — 3.6 V Regulator disabled VDDCORE 2.0 — 2.75 V Regulator disabled DC12 VDR RAM Data Retention 1.5 — — V Voltage(2) DC16 VPOR VDD Start Voltage VSS — — V to Ensure Internal Power-on Reset Signal DC17 SVDD VDD Rise Rate 0.05 — — V/ms 0-3.3V in 0.1s to Ensure Internal 0-2.5V in 60ms Power-on Reset Signal BO10 VBOR Brown-Out Reset 1.96 2.10 2.25 V Voltage BO15 VBHYS BOR Hysteresis — 5 — mV Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: This is the limit to which VDD can be lowered without losing RAM data.  2010 Microchip Technology Inc. DS39905E-page 271

PIC24FJ256GA110 FAMILY FIGURE 28-2: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING CHARACTERISTICS VDD MCLR SY12 SY10 Internal POR PWRT SY11 SYSRST System Clock Watchdog Timer Reset SY20 SY13 SY13 I/O Pins DS39905E-page 272  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 28-4: DC CHARACTERISTICS: OPERATING CURRENT (IDD) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter No. Typical(1) Max Units Conditions Operating Current (IDD): PMD Bits are Set(2) DC20 0.83 1.2 mA -40°C DC20a 0.83 1.2 mA +25°C 2.0V(3) DC20b 0.83 1.2 mA +85°C DC20c 0.9 1.3 mA +125°C 1 MIPS DC20d 1.1 1.7 mA -40°C DC20e 1.1 1.7 mA +25°C 3.3V(4) DC20f 1.1 1.7 mA +85°C DC20g 1.2 1.7 mA +125°C DC23 3.3 4.5 mA -40°C DC23a 3.3 4.5 mA +25°C 2.0V(3) DC23b 3.3 4.6 mA +85°C DC23c 3.4 4.6 mA +125°C 4 MIPS DC23d 4.3 6.5 mA -40°C DC23e 4.3 6.5 mA +25°C 3.3V(4) DC23f 4.3 6.5 mA +85°C DC23g 4.3 6.5 mA +125°C DC24 18.2 24.0 mA -40°C DC24a 18.2 24.0 mA +25°C 2.5V(3) DC24b 18.2 24.0 mA +85°C DC24c 18.2 24.0 mA +125°C 16 MIPS DC24d 18.2 24.0 mA -40°C DC24e 18.2 24.0 mA +25°C 3.3V(4) DC24f 18.2 24.0 mA +85°C DC24g 18.2 24.0 mA +125°C DC31 15.0 54.0 A -40°C DC31a 15.0 54.0 A +25°C 2.0V(3) DC31b 20.0 69.0 A +85°C DC31c 60.0 159.0 A +125°C LPRC (31 kHz) DC31d 57.0 96.0 A -40°C DC31e 57.0 96.0 A +25°C 3.3V(4) DC31f 95.0 145.0 A +85°C DC31g 120.0 281.0 A +125°C Note 1: Data in “Typical” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: OSCI driven with external square wave from rail to rail. All I/O pins are configured as inputs and pulled to VDD. MCLR = VDD; WDT and FSCM are disabled. CPU, SRAM, program memory and data memory are operational. No peripheral modules are operating and all of the Peripheral Module Disable (PMD) bits are set. 3: On-chip voltage regulator disabled (ENVREG tied to VSS). 4: On-chip voltage regulator enabled (ENVREG tied to VDD).  2010 Microchip Technology Inc. DS39905E-page 273

PIC24FJ256GA110 FAMILY TABLE 28-5: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter Typical(1) Max Units Conditions No. Idle Current (IIDLE): Core Off, Clock On Base Current, PMD Bits are Set(2) DC40 220 310 A -40°C DC40a 220 310 A +25°C 2.0V(3) DC40b 220 310 A +85°C DC40c 260 350 A +125°C 1 MIPS DC40d 300 390 A -40°C DC40e 300 390 A +25°C 3.3V(4) DC40f 320 420 A +85°C DC40g 340 450 A +125°C DC43 0.85 1.1 mA -40°C DC43a 0.85 1.1 mA +25°C 2.0V(3) DC43b 0.87 1.2 mA +85°C DC43c 0.87 1.2 mA +125°C 4 MIPS DC43d 1.1 1.4 mA -40°C DC43e 1.1 1.4 mA +25°C 3.3V(4) DC43f 1.1 1.4 mA +85°C DC43g 1.1 1.5 mA +125°C DC47 4.4 5.6 mA -40°C DC47a 4.4 5.6 mA +25°C 2.5V(3) DC47b 4.4 5.6 mA +85°C DC47c 4.4 5.6 mA +125°C 16 MIPS DC47d 4.4 5.6 mA -40°C DC47e 4.4 5.6 mA +25°C 3.3V(4) DC47f 4.4 5.6 mA +85°C DC47g 4.4 5.6 mA +125°C DC50 1.1 1.4 mA -40°C DC50a 1.1 1.4 mA +25°C 2.0V(3) DC50b 1.1 1.4 mA +85°C DC50c 1.2 1.5 mA +125°C FRC (4 MIPS) DC50d 1.4 1.8 mA -40°C DC50e 1.4 1.8 mA +25°C 3.3V(4) DC50f 1.4 1.8 mA +85°C DC50g 1.4 1.8 mA +125°C Note 1: Data in “Typical” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IIDLE current is measured with core off, clock on, all modules off and all of the Peripheral Module Disable (PMD) bits are set. 3: On-chip voltage regulator disabled (ENVREG tied to VSS). 4: On-chip voltage regulator enabled (ENVREG tied to VDD). DS39905E-page 274  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 28-5: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) (CONTINUED) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter Typical(1) Max Units Conditions No. Idle Current (IIDLE): Core Off, Clock On Base Current, PMD Bits are Set(2) DC51 4.3 13.0 A -40°C DC51a 4.5 13.0 A +25°C 2.0V(3) DC51b 10 32 A +85°C DC51c 40 115 A +125°C LPRC (31 kHz) DC51d 44 77 A -40°C DC51e 44 77 A +25°C 3.3V(4) DC51f 70 132 A +85°C DC51g 130 217 A +125°C Note 1: Data in “Typical” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IIDLE current is measured with core off, clock on, all modules off and all of the Peripheral Module Disable (PMD) bits are set. 3: On-chip voltage regulator disabled (ENVREG tied to VSS). 4: On-chip voltage regulator enabled (ENVREG tied to VDD).  2010 Microchip Technology Inc. DS39905E-page 275

PIC24FJ256GA110 FAMILY TABLE 28-6: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter Typical(1) Max Units Conditions No. Power-Down Current (IPD): PMD Bits are Set, PMSLP Bit is ‘0’(2) DC60 0.1 1.0 A -40°C DC60a 0.15 1.0 A +25°C DC60m 2.25 11 A +60°C 2.0V(3) DC60b 3.7 18.0 A +85°C DC60j 18.0 85.0 A +125°C DC60c 0.2 1.4 A -40°C DC60d 0.25 1.4 A +25°C DC60n 2.6 16.5 A +60°C 2.5V(3) Base Power-Down Current(5) DC60e 4.2 27 A +85°C DC60k 20.0 110 A +125°C DC60f 3.6 10.0 A -40°C DC60g 4.0 10 A +25°C DC60p 8.1 25.2 A +60°C 3.3V(4) DC60h 11.0 36 A +85°C DC60l 36.0 120 A +125°C DC61 1.75 3 A -40°C DC61a 1.75 3 A +25°C DC61m 1.75 3 A +60°C 2.0V(3) DC61b 1.75 3 A +85°C DC61j 3.5 6 A +125°C DC61c 2.4 4 A -40°C DC61d 2.4 4 A +25°C DC61n 2.4 4 A +60°C 2.5V(3) Watchdog Timer Current: IWDT(5) DC61e 2.4 4 A +85°C DC61k 4.8 8 A +125°C DC61f 2.8 5 A -40°C DC61g 2.8 5 A +25°C DC61p 2.8 5 A +60°C 3.3V(4) DC61h 2.8 5 A +85°C DC61l 5.6 10 A +125°C Note 1: Data in the Typical column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as inputs and pulled high. WDT, etc., are all switched off. 3: On-chip voltage regulator disabled (ENVREG tied to VSS). 4: On-chip voltage regulator enabled (ENVREG tied to VDD). 5: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. DS39905E-page 276  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 28-6: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter Typical(1) Max Units Conditions No. Power-Down Current (IPD): PMD Bits are Set, PMSLP Bit is ‘0’(2) DC62 2.5 7.0 A -40°C DC62a 2.5 7.0 A +25°C DC62m 3.0 7.0 A +60°C 2.0V(3) DC62b 3.0 7.0 A +85°C DC62j 6.0 12.0 A +125°C DC62c 2.8 7.0 A -40°C DC62d 3.0 7.0 A +25°C RTCC + Timer1 w/32 kHz Crystal: DC62n 3.0 7.0 A +60°C 2.5V(3) RTCC ITI32(5) DC62e 3.0 7.0 A +85°C DC62k 6.0 12.0 A +125°C DC62f 3.5 10.0 A -40°C DC62g 3.5 10.0 A +25°C DC62p 4.0 10.0 A +60°C 3.3V(4) DC62h 4.0 10.0 A +85°C DC62l 8.0 18.0 A +125°C Note 1: Data in the Typical column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as inputs and pulled high. WDT, etc., are all switched off. 3: On-chip voltage regulator disabled (ENVREG tied to VSS). 4: On-chip voltage regulator enabled (ENVREG tied to VDD). 5: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current.  2010 Microchip Technology Inc. DS39905E-page 277

PIC24FJ256GA110 FAMILY TABLE 28-7: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. VIL Input Low Voltage(4) DI10 I/O Pins with ST Buffer VSS — 0.2VDD V DI11 I/O Pins with TTL Buffer VSS — 0.15 VDD V DI15 MCLR VSS — 0.2VDD V DI16 OSC1 (XT mode) VSS — 0.2VDD V DI17 OSC1 (HS mode) VSS — 0.2VDD V DI18 I/O Pins with I2C™ Buffer VSS — 0.3VDD V DI19 I/O Pins with SMBus Buffer VSS — 0.8 V SMBus enabled VIH Input High Voltage(4,5) DI20 I/O Pins with ST Buffer: with Analog Functions 0.8VDD — VDD V Digital Only 0.8VDD — 5.5 V DI21 I/O Pins with TTL buffer: with Analog Functions 0.25VDD + 0.8 — VDD V Digital Only 0.25VDD + 0.8 — 5.5 V DI25 MCLR 0.8VDD — VDD V DI26 OSC1 (XT mode) 0.7VDD — VDD V DI27 OSC1 (HS mode) 0.7VDD — VDD V DI28 I/O Pins with I2C Buffer: with Analog Functions 0.7VDD — VDD V Digital Only 0.7VDD — 5.5 V DI29 I/O Pins with SMBus Buffer: 2.5V  VPIN  VDD with Analog Functions 2.1 VDD V Digital Only 2.1 5.5 V DI30 ICNPU CNx Pull-up Current 50 250 400 A VDD = 3.3V, VPIN = 0 DI30A ICNPD CNx Pull-Down Current — 80 — A VDD = 3.3V, VPIN = VDD DI31 IPU Maximum Load Current for — — 30 A VDD = 2.0V Digital High Detection w/ — — 100 A VDD = 3.3V Internal Pull-up Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. 4: Refer to Table1-4 for I/O pins buffer types. 5: VIH requirements are met when internal pull-ups are enabled. DS39905E-page 278  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 28-7: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. IIL Input Leakage Current(2,3) DI50 I/O Ports — — +1 A VSS  VPIN  VDD, Pin at high-impedance DI51 Analog Input Pins — — +1 A VSS  VPIN  VDD, Pin at high-impedance DI55 MCLR — — +1 A VSS VPIN VDD DI56 OSC1 — — +1 A VSS VPIN VDD, XT and HS modes Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. 4: Refer to Table1-4 for I/O pins buffer types. 5: VIH requirements are met when internal pull-ups are enabled. TABLE 28-8: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. VOL Output Low Voltage DO10 I/O Ports — — 0.4 V IOL = 8.5 mA, VDD = 3.6V — — 0.4 V IOL = 6.0 mA, VDD = 2.0V DO16 OSC2/CLKO — — 0.4 V IOL = 8.5 mA, VDD = 3.6V — — 0.4 V IOL = 6.0 mA, VDD = 2.0V VOH Output High Voltage DO20 I/O Ports 3.0 — — V IOH = -3.0 mA, VDD = 3.6V 2.4 — — V IOH = -6.0 mA, VDD = 3.6V 1.65 — — V IOH = -1.0 mA, VDD = 2.0V 1.4 — — V IOH = -3.0 mA, VDD = 2.0V DO26 OSC2/CLKO 2.4 — — V IOH = -6.0 mA, VDD = 3.6V 1.4 — — V IOH = -3.0 mA, VDD = 2.0V Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. 4: Refer to Table1-4 for I/O pins buffer types. 5: VIH requirements are met when internal pull-ups are enabled.  2010 Microchip Technology Inc. DS39905E-page 279

PIC24FJ256GA110 FAMILY TABLE 28-9: DC CHARACTERISTICS: PROGRAM MEMORY Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. D130 EP Cell Endurance 10000 — — E/W -40C to +85C D131 VPR VDD for Read VMIN — 3.6 V VMIN = Minimum operating voltage VPEW Supply Voltage for Self-Timed Writes D132A VDDCORE 2.25 — VDDCORE V D132B VDD 2.35 — 3.6 V D133A TIW Self-Timed Write Cycle Time — 3 — ms D133B TIE Self-Timed Page Erase Time 40 — — ms D134 TRETD Characteristic Retention 20 — — Year Provided no other specifications are violated D135 IDDP Supply Current during Programming — 7 — mA Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. TABLE 28-10: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS Operating Conditions: -40°C < TA < +125°C (unless otherwise stated) Param Symbol Characteristics Min Typ Max Units Comments No. VRGOUT Regulator Output Voltage — 2.5 — V VBG Internal Band Gap Reference — 1.2 — V CEFC External Filter Capacitor Value 4.7 10 — F Series resistance < 3 Ohm recommended; < 5 Ohm required. TVREG Regulator Start-up Time — 10 — s PMSLP = 1, or any POR or BOR — 250 — s Wake for Sleep when PMSLP = 0 TBG Band Gap Reference Start-up — — 1 ms Time DS39905E-page 280  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-3: CTMU CURRENT SOURCE CALIBRATION CIRCUIT PIC24F Device CTMU Current Source A/D Trigger A/D Converter AN2 A/D MUX RCAL  2010 Microchip Technology Inc. DS39905E-page 281

PIC24FJ256GA110 FAMILY 28.2 AC Characteristics and Timing Parameters The information contained in this section defines the PIC24FJ256GA110 family AC characteristics and timing parameters. TABLE 28-11: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial AC CHARACTERISTICS -40°C  TA  +125°C for Extended Operating voltage VDD range as described in Section28.1 “DC Characteristics”. FIGURE 28-4: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 1 – for all pins except OSCO Load Condition 2 – for OSCO VDD/2 RL Pin CL VSS CL Pin RL = 464 CL = 50 pF for all pins except OSCO VSS 15 pF for OSCO output TABLE 28-12: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS Param Symbol Characteristic Min Typ(1) Max Units Conditions No. DO50 COSC2 OSCO/CLKO Pin — — 15 pF In XT and HS modes when external clock is used to drive OSCI. DO56 CIO All I/O Pins and OSCO — — 50 pF EC mode. DO58 CB SCLx, SDAx — — 400 pF In I2C™ mode. Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. DS39905E-page 282  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-5: EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 OSCI OS20 OS30 OS30 OS31 OS31 OS25 CLKO OS40 OS41 TABLE 28-13: EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 2.50 to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. OS10 FOSC External CLKI Frequency DC — 32 MHz EC (external clocks allowed 4 — 8 MHz ECPLL only in EC mode) Oscillator Frequency 3 — 10 MHz XT 4 — 8 MHz XTPLL 10 — 32 MHz HS 31 — 33 kHz SOSC OS20 TOSC TOSC = 1/FOSC — — — — See Parameter OS10 for FOSC value OS25 TCY Instruction Cycle Time(2) 62.5 — DC ns OS30 TosL, External Clock in (OSCI) 0.45 x TOSC — — ns EC TosH High or Low Time OS31 TosR, External Clock in (OSCI) — — 20 ns EC TosF Rise or Fall Time OS40 TckR CLKO Rise Time(3) — 6 10 ns OS41 TckF CLKO Fall Time(3) — 6 10 ns Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “Min.” values with an external clock applied to the OSCI/CLKI pin. When an external clock input is used, the “Max.” cycle time limit is “DC” (no clock) for all devices. 3: Measurements are taken in EC mode. The CLKO signal is measured on the OSCO pin. CLKO is low for the Q1-Q2 period (1/2 TCY) and high for the Q3-Q4 period (1/2 TCY).  2010 Microchip Technology Inc. DS39905E-page 283

PIC24FJ256GA110 FAMILY TABLE 28-14: PLL CLOCK TIMING SPECIFICATIONS (VDD = 2.0V TO 3.6V) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic(1) Min Typ(2) Max Units Conditions No. OS50 FPLLI PLL Input Frequency 4 — 8 MHz ECPLL, HSPLL, XTPLL Range(2) modes OS51 FSYS PLL Output Frequency 16 — 32 MHz Range OS52 TLOCK PLL Start-up Time — — 2 ms (Lock Time) OS53 DCLK CLKO Stability (Jitter) -2 1 +2 % Note 1: These parameters are characterized but not tested in manufacturing. 2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. TABLE 28-15: INTERNAL RC OSCILLATOR SPECIFICATIONS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ Max Units Conditions No. TFRC FRC Start-up Time — 15 — s TLPRC LPRC Start-up Time — 40 — s TABLE 28-16: INTERNAL RC OSCILLATOR ACCURACY Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA +85°C for Industrial -40°C  TA  +125°C for Extended Param Characteristic Min Typ Max Units Conditions No. F20 FRC Accuracy @ 8MHz(1) -2 — 2 % +25°C, 3.0V  VDD 3.6V -5 — 5 % -40°C  TA +85°C, 3.0V  VDD 3.6V F21 LPRC Accuracy @ 31 kHz(2) -20 — 20 % -40°C  TA +85°C, 3.0V  VDD 3.6V Note 1: Frequency calibrated at 25°C and 3.3V. OSCTUN bits can be used to compensate for temperature drift. 2: Change of LPRC frequency as VDD changes. DS39905E-page 284  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-6: CLKO AND I/O TIMING CHARACTERISTICS I/O Pin (Input) DI35 DI40 I/O Pin Old Value New Value (Output) DO31 DO32 Note: Refer to Figure28-4 for load conditions. TABLE 28-17: CLKO AND I/O TIMING REQUIREMENTS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. DO31 TIOR Port Output Rise Time — 10 25 ns DO32 TIOF Port Output Fall Time — 10 25 ns DI35 TINP INTx pin High or Low 20 — — ns Time (output) DI40 TRBP CNx High or Low Time 2 — — TCY (input) Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. TABLE 28-18: RESET SPECIFICATIONS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Sym Characteristic Min Typ(1) Max Units Conditions TPOR Power-up Time — 2 — s TRST Internal State Reset Time — 50 — s TPWRT — 64 — ms ENVREG tied to VSS Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.  2010 Microchip Technology Inc. DS39905E-page 285

PIC24FJ256GA110 FAMILY TABLE 28-19: ADC MODULE SPECIFICATIONS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min. Typ Max. Units Conditions No. Device Supply AD01 AVDD Module VDD Supply Greater of — Lesser of V VDD – 0.3 VDD + 0.3 or 2.0 or 3.6 AD02 AVSS Module VSS Supply VSS – 0.3 — VSS + 0.3 V Reference Inputs AD05 VREFH Reference Voltage High AVSS + 1.7 — AVDD V AD06 VREFL Reference Voltage Low AVSS — AVDD – 1.7 V AD07 VREF Absolute Reference AVSS – 0.3 — AVDD + 0.3 V Voltage AD08 IVREF Reference Voltage Input — — 1.25 mA (Note 3) Current AD09 ZVREF Reference Input — 10K —  (Note 4) Impedance Analog Input AD10 VINH-VINL Full-Scale Input Span VREFL — VREFH V (Note 2) AD11 VIN Absolute Input Voltage AVSS – 0.3 — AVDD + 0.3 V AD12 VINL Absolute VINL Input AVSS – 0.3 AVDD/2 V Voltage AD17 RIN Recommended Impedance — — 2.5K  10-bit of Analog Voltage Source ADC Accuracy AD20b NR Resolution — 10 — bits AD21b INL Integral Nonlinearity — ±1 <±2 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 3V AD22b DNL Differential Nonlinearity — ±0.5 <±1 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 3V AD23b GERR Gain Error — ±1 ±3 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 3V AD24b EOFF Offset Error — ±1 ±2 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 3V AD25b — Monotonicity(1) — — — — Guaranteed Note 1: The ADC conversion result never decreases with an increase in the input voltage and has no missing codes. 2: Measurements taken with external VREF+ and VREF- are used as the ADC voltage reference. 3: External reference voltage applied to VREF+/- pins. IVREF is current during conversion at 3.3V, 25°C. Parameter is for design guidance only and is not tested. 4: Impedance during sampling is at 3.3V, 25°C. Parameter is for design guidance only and is not tested. DS39905E-page 286  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 28-20: ADC CONVERSION TIMING REQUIREMENTS(1) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min. Typ Max. Units Conditions No. Clock Parameters AD50 TAD ADC Clock Period 75 — — ns TCY = 75 ns, AD1CON3 in default state AD51 tRC ADC Internal RC Oscillator — 250 — ns Period Conversion Rate AD55 tCONV Conversion Time — 12 — TAD AD56 FCNV Throughput Rate — — 500 ksps AVDD > 2.7V AD57 tSAMP Sample Time — 1 — TAD Clock Parameters AD61 tPSS Sample Start Delay from Setting 2 — 3 TAD Sample bit (SAMP) AD132 TACQ Acquisition Time — — 750 ns (Note 2) AD135 TSWC Switching Time from Convert to — — (Note 3) Sample AD137 TDIS Discharge Time 0.5 — — TAD A/D Stabilization Time (from — 300 — ns setting ADON to setting SAMP) Note 1: Because the sample caps will eventually lose charge, clock rates below 10 kHz can affect linearity performance, especially at elevated temperatures.  2010 Microchip Technology Inc. DS39905E-page 287

PIC24FJ256GA110 FAMILY FIGURE 28-7: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING CHARACTERISTICS VDD MCLR SY12 SY10 Internal POR PWRT SY11 SYSRST System Clock Watchdog Timer Reset SY20 SY13 SY13 I/O Pins TABLE 28-21: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER AND BROWN-OUT RESET TIMING REQUIREMENTS Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SY10 TmcL MCLR Pulse Width (low) 2 — — s SY11 TPWRT Power-up Timer Period — 64 — ms SY12 TPOR Power-on Reset Delay 1 5 10 s SY13 TIOZ I/O High-Impedance from MCLR — — 100 ns Low or Watchdog Timer Reset SY20 TWDT Watchdog Timer Time-out Period 0.85 1.0 1.15 ms 1:32 prescaler 3.4 4.0 4.6 ms 1:128 prescaler SY25 TBOR Brown-out Reset Pulse Width 1 — — s VDD VBOR, voltage regulator disabled Note1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. DS39905E-page 288  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-8: BAUD RATE GENERATOR OUTPUT TIMING BRGx + 1 * TCY TLW THW BCLKx TBLD TBHD UxTX FIGURE 28-9: START BIT EDGE DETECTION BRGx Any Value TCY Start bit Detected, BRGx Started Cycle Clock TSETUP TSTDELAY UxRX TABLE 28-22: AC SPECIFICATIONS Symbol Characteristics Min Typ Max Units TLW BCLKx High Time 20 TCY/2 — ns THW BCLKx Low Time 20 (TCY * BRGx) + TCY/2 — ns TBLD BCLKx Falling Edge Delay from UxTX -50 — 50 ns TBHD BCLKx Rising Edge Delay from UxTX TCY/2 – 50 — TCY/2 + 50 ns TWAK Min. Low on UxRX Line to Cause Wake-up — 1 — s TCTS Min. Low on UxCTS Line to Start TCY — — ns Transmission TSETUP Start bit Falling Edge to System Clock Rising 3 — — ns Edge Setup Time TSTDELAY Maximum Delay in the Detection of the — — TCY + TSETUP ns Start bit Falling Edge  2010 Microchip Technology Inc. DS39905E-page 289

PIC24FJ256GA110 FAMILY FIGURE 28-10: INPUT CAPTURE TIMINGS ICx pin (Input Capture Mode) IC11 IC10 IC15 TABLE 28-23: INPUT CAPTURE Param. Symbol Characteristic Min Max Units Conditions No. IC10 TccL ICx Input Low Time – No Prescaler TCY + 20 — ns Must also meet Synchronous Timer With Prescaler 20 — ns parameter IC15 IC11 TccH ICx Input Low Time – No Prescaler TCY + 20 — ns Must also meet Synchronous Timer With Prescaler 20 — ns parameter IC15 IC15 TccP ICx Input Period – Synchronous Timer 2 * TCY + 40 — ns N = prescale N value (1, 4, 16) DS39905E-page 290  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-11: SPIx MODULE MASTER MODE TIMING CHARACTERISTICS (CKE = 0) SCKx (CKP = 0) SP11 SP10 SP21 SP20 SCKx (CKP = 1) SP35 SP20 SP21 SDOx MSb Bit 14 - - - - - -1 LSb SP31 SP30 SDIx MSb In Bit 14 - - - -1 LSb In SP40 SP41 TABLE 28-24: SPIx MASTER MODE TIMING REQUIREMENTS (CKE = 0) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP10 TscL SCKx Output Low Time(2) TCY/2 — — ns SP11 TscH SCKx Output High Time(2) TCY/2 — — ns SP20 TscF SCKx Output Fall Time(3) — 10 25 ns SP21 TscR SCKx Output Rise Time(3) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(3) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(3) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after — — 30 ns TscL2doV SCKx Edge SP40 TdiV2scH, Setup Time of SDIx Data Input 20 — — ns TdiV2scL to SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input 20 — — ns TscL2diL to SCKx Edge Note1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The minimum clock period for SCKx is 100 ns; therefore, the clock generated in Master mode must not violate this specification. 3: Assumes 50 pF load on all SPIx pins.  2010 Microchip Technology Inc. DS39905E-page 291

PIC24FJ256GA110 FAMILY FIGURE 28-12: SPIx MODULE MASTER MODE TIMING CHARACTERISTICS (CKE = 1) SP36 SCKx (CKP = 0) SP11 SP10 SP21 SP20 SCKx (CKP = 1) SP35 SP20 SP21 SDOx MSb Bit 14 - - - - - -1 LSb SP40 SP30,SP31 SDIx MSb In Bit 14 - - - -1 LSb In SP41 TABLE 28-25: SPIx MODULE MASTER MODE TIMING REQUIREMENTS (CKE = 1) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP10 TscL SCKx Output Low Time(2) TCY/2 — — ns SP11 TscH SCKx Output High Time(2) TCY/2 — — ns SP20 TscF SCKx Output Fall Time(3) — 10 25 ns SP21 TscR SCKx Output Rise Time(3) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(3) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(3) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after — — 30 ns TscL2doV SCKx Edge SP36 TdoV2sc, SDOx Data Output Setup to 30 — — ns TdoV2scL First SCKx Edge SP40 TdiV2scH, Setup Time of SDIx Data Input 20 — — ns TdiV2scL to SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input 20 — — ns TscL2diL to SCKx Edge Note1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The minimum clock period for SCKx is 100 ns. Therefore, the clock generated in Master mode must not violate this specification. 3: Assumes 50 pF load on all SPIx pins. DS39905E-page 292  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-13: SPIx MODULE SLAVE MODE TIMING CHARACTERISTICS (CKE = 0) SSx SP50 SP52 SCKx (CKP = 0) SP71 SP70 SP73 SP72 SCKx (CKP = 1) SP72 SP73 SP35 SDOx MSb Bit 14 - - - - - -1 LSb SP30,SP31 SP51 SSDDIIx MSb In Bit 14 - - - -1 LSb In SP41 SP40 TABLE 28-26: SPIx MODULE SLAVE MODE TIMING REQUIREMENTS (CKE = 0) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP70 TscL SCKx Input Low Time 30 — — ns SP71 TscH SCKx Input High Time 30 — — ns SP72 TscF SCKx Input Fall Time(2) — 10 25 ns SP73 TscR SCKx Input Rise Time(2) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(2) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(2) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after — — 30 ns TscL2doV SCKx Edge SP40 TdiV2scH, Setup Time of SDIx Data Input 20 — — ns TdiV2scL to SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input 20 — — ns TscL2diL to SCKx Edge SP50 TssL2scH, SSx to SCKx  or SCKx Input 120 — — ns TssL2scL SP51 TssH2doZ SSx  to SDOx Output 10 — 50 ns High-Impedance(3) SP52 TscH2ssH SSx after SCKx Edge 1.5 TCY + 40 — — ns TscL2ssH Note1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Assumes 50 pF load on all SPIx pins.  2010 Microchip Technology Inc. DS39905E-page 293

PIC24FJ256GA110 FAMILY FIGURE 28-14: SPIx MODULE SLAVE MODE TIMING CHARACTERISTICS (CKE = 1) SP60 SSx SP50 SP52 SCKx (CKP = 0) SP71 SP70 SP73 SP72 SCKx (CKP = 1) SP35 SP72 SP73 SP52 SDOx MSb Bit 14 - - - - - -1 LSb SP30,SP31 SP51 SDIx MSb In Bit 14 - - - -1 LSb In SP41 SP40 TABLE 28-27: SPIx MODULE SLAVE MODE TIMING REQUIREMENTS (CKE = 1) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP70 TscL SCKx Input Low Time 30 — — ns SP71 TscH SCKx Input High Time 30 — — ns SP72 TscF SCKx Input Fall Time(2) — 10 25 ns SP73 TscR SCKx Input Rise Time(2) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(2) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(2) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after SCKx Edge — — 30 ns TscL2doV SP40 TdiV2scH, Setup Time of SDIx Data Input to 20 — — ns TdiV2scL SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input to 20 — — ns TscL2diL SCKx Edge SP50 TssL2scH, SSx  to SCKx  or SCKx  Input 120 — — ns TssL2scL SP51 TssH2doZ SSx  to SDOx Output 10 — 50 ns High-Impedance(3) SP52 TscH2ssH SSx  after SCKx Edge 1.5 TCY + 40 — — ns TscL2ssH SP60 TssL2doV SDOx Data Output Valid after SSx Edge — — 50 ns Note1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The minimum clock period for SCKx is 100 ns. Therefore, the clock generated in Master mode must not violate this specification. 3: Assumes 50 pF load on all SPIx pins. DS39905E-page 294  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-15: OUTPUT COMPARE TIMINGS OCx (Output Compare or PWM Mode) OC11 OC10 TABLE 28-28: OUTPUT COMPARE Param. Symbol Characteristic Min Max Unit Condition No. OC11 TCCR OC1 Output Rise Time — 10 ns — — — ns — OC10 TCCF OC1 Output Fall Time — 10 ns — — — ns — FIGURE 28-16: PWM MODULE TIMING REQUIREMENTS OC20 OCFx OC15 PWM TABLE 28-29: PWM TIMING REQUIREMENTS Param. Symbol Characteristic Min Typ(1) Max Unit Condition No. OC15 TFD Fault Input to PWM I/O — — 25 ns VDD = 3.0V, -40C to +85C Change OC20 TFH Fault Input Pulse Width 50 — — ns VDD = 3.0V, -40C to +85C Note1: Data in “Typ” column is at 3.3V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.  2010 Microchip Technology Inc. DS39905E-page 295

PIC24FJ256GA110 FAMILY FIGURE 28-17: I2C™ BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE) SCLx IM31 IM34 IM30 IM33 SDAx Start Stop Condition Condition Note: Refer to Figure28-4 for load conditions. TABLE 28-30: I2C™ BUS START/STOP BIT TIMING REQUIREMENTS (MASTER MODE) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C (Industrial) Param Symbol Characteristic Min(1) Max Units Conditions No. IM30 TSU:STA Start Condition 100 kHz mode TCY/2 (BRG + 1) — s Only relevant for Setup Time Repeated Start 400 kHz mode TCY/2 (BRG + 1) — s condition 1 MHz mode(2) TCY/2 (BRG + 1) — s IM31 THD:STA Start Condition 100 kHz mode TCY/2 (BRG + 1) — s After this period, the Hold Time first clock pulse is 400 kHz mode TCY/2 (BRG + 1) — s generated 1 MHz mode(2) TCY/2 (BRG + 1) — s IM33 TSU:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1) — s — Setup Time 400 kHz mode TCY/2 (BRG + 1) — s 1 MHz mode(2) TCY/2 (BRG + 1) — s IM34 THD:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1) — ns — Hold Time 400 kHz mode TCY/2 (BRG + 1) — ns 1 MHz mode(2) TCY/2 (BRG + 1) — ns Note 1: BRG is the value of the I2C™ Baud Rate Generator. Refer to Section 16.3 “Setting Baud Rate When Operating as a Bus Master” for details 2: Maximum pin capacitance = 10 pF for all I2C pins (for 1 MHz mode only). DS39905E-page 296  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-18: I2C™ BUS DATA TIMING CHARACTERISTICS (MASTER MODE) IM11 IM21 SCLx IM10 IM25 IM26 IM20 SDAx In IM45 IM40 SDAx Out Note: Refer to Figure28-4 for load conditions. TABLE 28-31: I2C™ BUS DATA TIMING REQUIREMENTS (MASTER MODE) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C (Industrial) Param Symbol Characteristic Min(1) Max Units Conditions No. IM10 TLO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 1) — s — 400 kHz mode TCY/2 (BRG + 1) — s — 1 MHz mode(2) TCY/2 (BRG + 1) — s — IM11 THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 1) — s — 400 kHz mode TCY/2 (BRG + 1) — s — 1 MHz mode(2) TCY/2 (BRG + 1) — s — IM20 TF:SCL SDAx and SCLx 100 kHz mode — 300 ns CB is specified to be Fall Time 400 kHz mode 20 + 0.1 CB 300 ns from 10 to 400 pF 1 MHz mode(2) — 100 ns IM21 TR:SCL SDAx and SCLx 100 kHz mode — 1000 ns CB is specified to be Rise Time 400 kHz mode 20 + 0.1 CB 300 ns from 10 to 400 pF 1 MHz mode(2) — 300 ns IM25 TSU:DAT Data Input 100 kHz mode 250 — ns — Setup Time 400 kHz mode 100 — ns 1 MHz mode(2) TBD — ns IM26 THD:DAT Data Input 100 kHz mode 0 — ns — Hold Time 400 kHz mode 0 0.9 s 1 MHz mode(2) TBD — ns IM40 TAA:SCL Output Valid 100 kHz mode — 3500 ns — From Clock 400 kHz mode — 1000 ns — 1 MHz mode(2) — — ns — IM45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — s Time the bus must be 400 kHz mode 1.3 — s free before a new transmission can start 1 MHz mode(2) TBD — s IM50 CB Bus Capacitive Loading — 400 pF — Legend: TBD = To Be Determined Note 1: BRG is the value of the I2C Baud Rate Generator. Refer to Section 16.3 “Setting Baud Rate When Operating as a Bus Master” for details. 2: Maximum pin capacitance = 10 pF for all I2C pins (for 1 MHz mode only).  2010 Microchip Technology Inc. DS39905E-page 297

PIC24FJ256GA110 FAMILY FIGURE 28-19: I2C™ BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE) SCLx IS31 IS34 IS30 IS33 SDAx Start Stop Condition Condition TABLE 28-32: I2C™ BUS START/STOP BIT TIMING REQUIREMENTS (SLAVE MODE) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C (Industrial) Param Symbol Characteristic Min Max Units Conditions No. IS30 TSU:STA Start Condition 100 kHz mode 4.7 — s Only relevant for Repeated Setup Time 400 kHz mode 0.6 — s Start condition 1 MHz mode(1) 0.25 — s IS31 THD:STA Start Condition 100 kHz mode 4.0 — s After this period, the first Hold Time 400 kHz mode 0.6 — s clock pulse is generated 1 MHz mode(1) 0.25 — s IS33 TSU:STO Stop Condition 100 kHz mode 4.7 — s — Setup Time 400 kHz mode 0.6 — s 1 MHz mode(1) 0.6 — s IS34 THD:STO Stop Condition 100 kHz mode 4000 — ns — Hold Time 400 kHz mode 600 — ns 1 MHz mode(1) 250 — ns Note 1: Maximum pin capacitance = 10 pF for all I2C™ pins (for 1 MHz mode only). DS39905E-page 298  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-20: I2C™ BUS DATA TIMING CHARACTERISTICS (SLAVE MODE) IS11 IS21 IS10 SCLx IS25 IS20 IS26 SDAx In IS45 IS40 SDAx Out TABLE 28-33: I2C™ BUS DATA TIMING REQUIREMENTS (SLAVE MODE) Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C (Industrial) Param Symbol Characteristic Min Max Units Conditions No. IS10 TLO:SCL Clock Low Time 100 kHz mode 4.7 — s Device must operate at a minimum of 1.5 MHz 400 kHz mode 1.3 — s Device must operate at a minimum of 10 MHz 1 MHz mode(1) 0.5 — s — IS11 THI:SCL Clock High Time 100 kHz mode 4.0 — s Device must operate at a minimum of 1.5 MHz 400 kHz mode 0.6 — s Device must operate at a minimum of 10 MHz 1 MHz mode(1) 0.5 — s — IS20 TF:SCL SDAx and SCLx 100 kHz mode — 300 ns CB is specified to be from Fall Time 400 kHz mode 20 + 0.1 CB 300 ns 10 to 400 pF 1 MHz mode(1) — 100 ns IS21 TR:SCL SDAx and SCLx 100 kHz mode — 1000 ns CB is specified to be from Rise Time 400 kHz mode 20 + 0.1 CB 300 ns 10 to 400 pF 1 MHz mode(1) — 300 ns IS25 TSU:DAT Data Input 100 kHz mode 250 — ns — Setup Time 400 kHz mode 100 — ns 1 MHz mode(1) 100 — ns IS26 THD:DAT Data Input 100 kHz mode 0 — ns — Hold Time 400 kHz mode 0 0.9 s 1 MHz mode(1) 0 0.3 s IS40 TAA:SCL Output Valid From 100 kHz mode 0 3500 ns — Clock 400 kHz mode 0 1000 ns 1 MHz mode(1) 0 350 ns IS45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — s Time the bus must be free 400 kHz mode 1.3 — s before a new transmission can start 1 MHz mode(1) 0.5 — s IS50 CB Bus Capacitive Loading — 400 pF — Note 1: Maximum pin capacitance = 10 pF for all I2C™ pins (for 1 MHz mode only).  2010 Microchip Technology Inc. DS39905E-page 299

PIC24FJ256GA110 FAMILY FIGURE 28-21: PARALLEL SLAVE PORT TIMING CS RD WR PS4 PMD<7:0> PS1 PS3 PS2 TABLE 28-34: PARALLEL SLAVE PORT REQUIREMENTS Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param. Symbol Characteristic Min Typ Max Units Conditions No. PS1 TdtV2wrH Data In Valid before WR or CS Inactive 20 — — ns (setup time) PS2 TwrH2dtI WR or CS Inactive to Data–In Invalid 20 — — ns (hold time) PS3 TrdL2dtV RD and CS Active to Data–Out Valid — — 80 ns PS4 TrdH2dtI RD Activeor CS Inactive to Data–Out 10 — 30 ns Invalid DS39905E-page 300  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY FIGURE 28-22: PARALLEL MASTER PORT READ TIMING DIAGRAM P1 P2 P3 P4 P1 P2 P3 P4 P1 P2 System Clock PMA<13:18> Address PMD<7:0> Address<7:0> Data PM6 PM2 PM7 PM3 PMRD PM5 PMWR PMALL/PMALH PM1 PMCS<2:1> Operating Conditions: 2.0V < VCC < 3.6V, -40°C < TA < +85°C unless otherwise stated. TABLE 28-35: PARALLEL MASTER PORT READ TIMING REQUIREMENTS Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param. Symbol Characteristics(1) Min Typ Max Units Conditions No PM1 PMALL/PMALH Pulse Width — 0.5 TCY — ns PM2 Address Out Valid to PMALL/PMALH — 0.75 TCY — ns Invalid (address setup time)(2) PM3 PMALL/PMALH Invalid to Address Out — 0.25 TCY — ns Invalid (address hold time) PM5 PMRD Pulse Width — 0.5 TCY — ns PM6 Data In to PMRD or PMENB Inactive 150 — — ns state PM7 PMRD or PMENB Inactive to Data In — — 5 ns Invalid (data hold time) Note1: Wait states disabled for all cases. 2: The setup time for the LSB and the MSB of the address are not the same; the setup time for the LSB is 0.5TCY and for the MSB is 0.75 TCY.  2010 Microchip Technology Inc. DS39905E-page 301

PIC24FJ256GA110 FAMILY FIGURE 28-23: PARALLEL MASTER PORT WRITE TIMING DIAGRAM P1 P2 P3 P4 P1 P2 P3 P4 P1 P2 System Clock PMA<13:18> Address PMD<7:0> Address<7:0> Data PM12 PM13 PMRD PMWR PM11 PMALL/PMALH PMCS<2:1> PM16 Operating Conditions: 2.0V < VCC < 3.6V, -40°C < TA < +85°C unless otherwise stated. TABLE 28-36: PARALLEL MASTER PORT WRITE TIMING REQUIREMENTS Standard Operating Conditions: 2.0V to 3.6V AC CHARACTERISTICS (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Param. Symbol Characteristics(1) Min Typ Max Units Conditions No PM11 PMWR Pulse Width — 0.5 TCY — ns PM12 Data Out Valid before PMWR or — 0.75 TCY — ns PMENB goes Inactive (data setup time) PM13 PMWR or PMEMB Invalid to Data Out — 0.25 TCY — ns Invalid (data hold time) PM16 PMCSx Pulse Width TCY – 5 — — ns Note 1: Wait states disabled for all cases. DS39905E-page 302  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY TABLE 28-37: COMPARATOR TIMINGS Param Symbol Characteristic Min Typ Max Units Comments No. 300 TRESP Response Time*(1) — 150 400 ns 301 TMC2OV Comparator Mode Chance to Output — — 10 s Valid* * Parameters are characterized but not tested. Note 1: Response time measured with one comparator input at (VDD – 1.5)/2, while the other input transitions from VSS to VDD. TABLE 28-38: DC SPECIFICATIONS Operating Conditions: 2.0V < VDD < 3.6V, -40°C < TA < +85°C (unless otherwise stated) Param Symbol Characteristic Min Typ Max Units Comments No. VRD310 CVRES Resolution CVRSRC/24 — CVRSRC/32 LSb VRD311 CVRAA Absolute Accuracy — — TBD LSb VRD312 CVRUR Unit Resistor Value (R) — 2k —  Legend: TBD = To Be Determined  2010 Microchip Technology Inc. DS39905E-page 303

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 304  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 29.0 PACKAGING INFORMATION 29.1 Package Marking Information 64-Lead TQFP (10x10x1 mm) Example XXXXXXXXXX PIC24FJ256 XXXXXXXXXX GA106-I/ XXXXXXXXXX PTe3 YYWWNNN 1020017 64-Lead QFN (9x9x0.9 mm) Example XXXXXXXXXXX PIC24FJ256 XXXXXXXXXXX GA006-I/MRe3 XXXXXXXXXXX 1010017 YYWWNNN 80-Lead TQFP (12x12x1 mm) Example XXXXXXXXXXXX PIC24FJ256GA XXXXXXXXXXXX 108-I/PTe3 YYWWNNN 1020017 Legend: XX...X Customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code e3 Pb-free JEDEC designator for Matte Tin (Sn) * This package is Pb-free. The Pb-free JEDEC designator ( e 3 ) can be found on the outer packaging for this package. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  2010 Microchip Technology Inc. DS39905E-page 305

PIC24FJ256GA110 FAMILY 100-Lead TQFP (12x12x1 mm) Example XXXXXXXXXXXX PIC24FJ256GA XXXXXXXXXXXX 110-I/PTe3 YYWWNNN 0920017 100-Lead TQFP (14x14x1 mm) Example XXXXXXXXXXXX PIC24FJ256GA XXXXXXXXXXXX 110-I/PFe3 YYWWNNN 0920017 DS39905E-page 306  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY 29.2 Package Details The following sections give the technical details of the packages. (cid:2)(cid:3)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:16)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)(cid:28)(cid:29)(cid:27)(cid:28)(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12) D D1 E e E1 N b NOTE1 123 NOTE2 α A c φ A2 β A1 L L1 6(cid:26)(cid:20)&! (cid:19)(cid:29)77(cid:29)(cid:19).(cid:25).(cid:8)(cid:3) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:14)7(cid:20)’(cid:20)&! (cid:19)(cid:29)8 89(cid:19) (cid:19)(cid:7): 8"’)(cid:13)(cid:22)(cid:14)(cid:23)%(cid:14)7(cid:13)(cid:11)#! 8 ;(cid:5) 7(cid:13)(cid:11)#(cid:14)(cid:31)(cid:20)&(cid:21)(cid:24) (cid:13) (cid:4)(cid:30)/(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)<(cid:13)(cid:20)(cid:12)(cid:24)& (cid:7) = = (cid:15)(cid:30)(cid:17)(cid:4) (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:7)(cid:17) (cid:4)(cid:30)(cid:6)/ (cid:15)(cid:30)(cid:4)(cid:4) (cid:15)(cid:30)(cid:4)/ (cid:3)&(cid:11)(cid:26)#(cid:23)%%(cid:14)(cid:14) (cid:7)(cid:15) (cid:4)(cid:30)(cid:4)/ = (cid:4)(cid:30)(cid:15)/ 3(cid:23)(cid:23)&(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) 7 (cid:4)(cid:30)(cid:5)/ (cid:4)(cid:30);(cid:4) (cid:4)(cid:30)(cid:18)/ 3(cid:23)(cid:23)&(cid:10)(cid:22)(cid:20)(cid:26)& 7(cid:15) (cid:15)(cid:30)(cid:4)(cid:4)(cid:14)(cid:8).3 3(cid:23)(cid:23)&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13) (cid:3) (cid:4)> (cid:16)(cid:30)/> (cid:18)> 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)?(cid:20)#&(cid:24) . (cid:15)(cid:17)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2) (cid:15)(cid:17)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)?(cid:20)#&(cid:24) .(cid:15) (cid:15)(cid:4)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2)(cid:15) (cid:15)(cid:4)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 7(cid:13)(cid:11)#(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:21) (cid:4)(cid:30)(cid:4)(cid:6) = (cid:4)(cid:30)(cid:17)(cid:4) 7(cid:13)(cid:11)#(cid:14)?(cid:20)#&(cid:24) ) (cid:4)(cid:30)(cid:15)(cid:18) (cid:4)(cid:30)(cid:17)(cid:17) (cid:4)(cid:30)(cid:17)(cid:18) (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)(cid:25)(cid:23)(cid:10) (cid:4) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)1(cid:23)&&(cid:23)’ (cid:5) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> ’ (cid:13)(cid:6)(cid:12)( (cid:15)(cid:30) (cid:31)(cid:20)(cid:26)(cid:14)(cid:15)(cid:14) (cid:20)!"(cid:11)(cid:27)(cid:14)(cid:20)(cid:26)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:22)(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)*(cid:20)&(cid:24)(cid:20)(cid:26)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:24)(cid:11)&(cid:21)(cid:24)(cid:13)#(cid:14)(cid:11)(cid:22)(cid:13)(cid:11)(cid:30) (cid:17)(cid:30) +(cid:24)(cid:11)’%(cid:13)(cid:22)!(cid:14)(cid:11)&(cid:14)(cid:21)(cid:23)(cid:22)(cid:26)(cid:13)(cid:22)!(cid:14)(cid:11)(cid:22)(cid:13)(cid:14)(cid:23)(cid:10)&(cid:20)(cid:23)(cid:26)(cid:11)(cid:27),(cid:14)!(cid:20)-(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)(cid:30) (cid:16)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)!(cid:14)(cid:2)(cid:15)(cid:14)(cid:11)(cid:26)#(cid:14).(cid:15)(cid:14)#(cid:23)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:20)(cid:26)(cid:21)(cid:27)"#(cid:13)(cid:14)’(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:30)(cid:14)(cid:19)(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:14)!(cid:24)(cid:11)(cid:27)(cid:27)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:13)$(cid:21)(cid:13)(cid:13)#(cid:14)(cid:4)(cid:30)(cid:17)/(cid:14)’’(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)!(cid:20)#(cid:13)(cid:30) (cid:5)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:20)(cid:26)(cid:12)(cid:14)(cid:11)(cid:26)#(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:20)(cid:26)(cid:12)(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)(cid:7)(cid:3)(cid:19).(cid:14)0(cid:15)(cid:5)(cid:30)/(cid:19)(cid:30) 1(cid:3)+2 1(cid:11)!(cid:20)(cid:21)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:30)(cid:14)(cid:25)(cid:24)(cid:13)(cid:23)(cid:22)(cid:13)&(cid:20)(cid:21)(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)(cid:13)$(cid:11)(cid:21)&(cid:14) (cid:11)(cid:27)"(cid:13)(cid:14)!(cid:24)(cid:23)*(cid:26)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)!(cid:30) (cid:8).32 (cid:8)(cid:13)%(cid:13)(cid:22)(cid:13)(cid:26)(cid:21)(cid:13)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)((cid:14)"!"(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)((cid:14)%(cid:23)(cid:22)(cid:14)(cid:20)(cid:26)%(cid:23)(cid:22)’(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:10)"(cid:22)(cid:10)(cid:23)!(cid:13)!(cid:14)(cid:23)(cid:26)(cid:27)(cid:28)(cid:30) (cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:25)(cid:13)(cid:21)(cid:24)(cid:26)(cid:23)(cid:27)(cid:23)(cid:12)(cid:28)(cid:2)(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)+(cid:4)(cid:5)(cid:9)(cid:4)@/1  2010 Microchip Technology Inc. DS39905E-page 307

PIC24FJ256GA110 FAMILY (cid:2)(cid:3)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:16)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)(cid:28)(cid:29)(cid:27)(cid:28)(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12) DS39905E-page 308  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2010 Microchip Technology Inc. DS39905E-page 309

PIC24FJ256GA110 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS39905E-page 310  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2010 Microchip Technology Inc. DS39905E-page 311

PIC24FJ256GA110 FAMILY )(cid:28)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:16)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)#(cid:29)(cid:27)#(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12) D D1 E e E1 b N NOTE1 123 NOTE2 α A c φ β A1 A2 L L1 6(cid:26)(cid:20)&! (cid:19)(cid:29)77(cid:29)(cid:19).(cid:25).(cid:8)(cid:3) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:14)7(cid:20)’(cid:20)&! (cid:19)(cid:29)8 89(cid:19) (cid:19)(cid:7): 8"’)(cid:13)(cid:22)(cid:14)(cid:23)%(cid:14)7(cid:13)(cid:11)#! 8 @(cid:4) 7(cid:13)(cid:11)#(cid:14)(cid:31)(cid:20)&(cid:21)(cid:24) (cid:13) (cid:4)(cid:30)/(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)<(cid:13)(cid:20)(cid:12)(cid:24)& (cid:7) = = (cid:15)(cid:30)(cid:17)(cid:4) (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:7)(cid:17) (cid:4)(cid:30)(cid:6)/ (cid:15)(cid:30)(cid:4)(cid:4) (cid:15)(cid:30)(cid:4)/ (cid:3)&(cid:11)(cid:26)#(cid:23)%%(cid:14)(cid:14) (cid:7)(cid:15) (cid:4)(cid:30)(cid:4)/ = (cid:4)(cid:30)(cid:15)/ 3(cid:23)(cid:23)&(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) 7 (cid:4)(cid:30)(cid:5)/ (cid:4)(cid:30);(cid:4) (cid:4)(cid:30)(cid:18)/ 3(cid:23)(cid:23)&(cid:10)(cid:22)(cid:20)(cid:26)& 7(cid:15) (cid:15)(cid:30)(cid:4)(cid:4)(cid:14)(cid:8).3 3(cid:23)(cid:23)&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13) (cid:3) (cid:4)> (cid:16)(cid:30)/> (cid:18)> 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)?(cid:20)#&(cid:24) . (cid:15)(cid:5)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2) (cid:15)(cid:5)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)?(cid:20)#&(cid:24) .(cid:15) (cid:15)(cid:17)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2)(cid:15) (cid:15)(cid:17)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 7(cid:13)(cid:11)#(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:21) (cid:4)(cid:30)(cid:4)(cid:6) = (cid:4)(cid:30)(cid:17)(cid:4) 7(cid:13)(cid:11)#(cid:14)?(cid:20)#&(cid:24) ) (cid:4)(cid:30)(cid:15)(cid:18) (cid:4)(cid:30)(cid:17)(cid:17) (cid:4)(cid:30)(cid:17)(cid:18) (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)(cid:25)(cid:23)(cid:10) (cid:4) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)1(cid:23)&&(cid:23)’ (cid:5) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> ’ (cid:13)(cid:6)(cid:12)( (cid:15)(cid:30) (cid:31)(cid:20)(cid:26)(cid:14)(cid:15)(cid:14) (cid:20)!"(cid:11)(cid:27)(cid:14)(cid:20)(cid:26)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:22)(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)*(cid:20)&(cid:24)(cid:20)(cid:26)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:24)(cid:11)&(cid:21)(cid:24)(cid:13)#(cid:14)(cid:11)(cid:22)(cid:13)(cid:11)(cid:30) (cid:17)(cid:30) +(cid:24)(cid:11)’%(cid:13)(cid:22)!(cid:14)(cid:11)&(cid:14)(cid:21)(cid:23)(cid:22)(cid:26)(cid:13)(cid:22)!(cid:14)(cid:11)(cid:22)(cid:13)(cid:14)(cid:23)(cid:10)&(cid:20)(cid:23)(cid:26)(cid:11)(cid:27),(cid:14)!(cid:20)-(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)(cid:30) (cid:16)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)!(cid:14)(cid:2)(cid:15)(cid:14)(cid:11)(cid:26)#(cid:14).(cid:15)(cid:14)#(cid:23)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:20)(cid:26)(cid:21)(cid:27)"#(cid:13)(cid:14)’(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:30)(cid:14)(cid:19)(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:14)!(cid:24)(cid:11)(cid:27)(cid:27)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:13)$(cid:21)(cid:13)(cid:13)#(cid:14)(cid:4)(cid:30)(cid:17)/(cid:14)’’(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)!(cid:20)#(cid:13)(cid:30) (cid:5)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:20)(cid:26)(cid:12)(cid:14)(cid:11)(cid:26)#(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:20)(cid:26)(cid:12)(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)(cid:7)(cid:3)(cid:19).(cid:14)0(cid:15)(cid:5)(cid:30)/(cid:19)(cid:30) 1(cid:3)+2 1(cid:11)!(cid:20)(cid:21)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:30)(cid:14)(cid:25)(cid:24)(cid:13)(cid:23)(cid:22)(cid:13)&(cid:20)(cid:21)(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)(cid:13)$(cid:11)(cid:21)&(cid:14) (cid:11)(cid:27)"(cid:13)(cid:14)!(cid:24)(cid:23)*(cid:26)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)!(cid:30) (cid:8).32 (cid:8)(cid:13)%(cid:13)(cid:22)(cid:13)(cid:26)(cid:21)(cid:13)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)((cid:14)"!"(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)((cid:14)%(cid:23)(cid:22)(cid:14)(cid:20)(cid:26)%(cid:23)(cid:22)’(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:10)"(cid:22)(cid:10)(cid:23)!(cid:13)!(cid:14)(cid:23)(cid:26)(cid:27)(cid:28)(cid:30) (cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:25)(cid:13)(cid:21)(cid:24)(cid:26)(cid:23)(cid:27)(cid:23)(cid:12)(cid:28)(cid:2)(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)+(cid:4)(cid:5)(cid:9)(cid:4)(cid:6)(cid:17)1 DS39905E-page 312  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY )(cid:28)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:16)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)#(cid:29)(cid:27)#(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)  2010 Microchip Technology Inc. DS39905E-page 313

PIC24FJ256GA110 FAMILY (cid:27)(cid:28)(cid:28)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:16)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)#(cid:29)(cid:27)#(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12) D D1 e E E1 N b NOTE1 123 NOTE2 α c A φ β L A1 L1 A2 6(cid:26)(cid:20)&! (cid:19)(cid:29)77(cid:29)(cid:19).(cid:25).(cid:8)(cid:3) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:14)7(cid:20)’(cid:20)&! (cid:19)(cid:29)8 89(cid:19) (cid:19)(cid:7): 8"’)(cid:13)(cid:22)(cid:14)(cid:23)%(cid:14)7(cid:13)(cid:11)#! 8 (cid:15)(cid:4)(cid:4) 7(cid:13)(cid:11)#(cid:14)(cid:31)(cid:20)&(cid:21)(cid:24) (cid:13) (cid:4)(cid:30)(cid:5)(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)<(cid:13)(cid:20)(cid:12)(cid:24)& (cid:7) = = (cid:15)(cid:30)(cid:17)(cid:4) (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:7)(cid:17) (cid:4)(cid:30)(cid:6)/ (cid:15)(cid:30)(cid:4)(cid:4) (cid:15)(cid:30)(cid:4)/ (cid:3)&(cid:11)(cid:26)#(cid:23)%%(cid:14)(cid:14) (cid:7)(cid:15) (cid:4)(cid:30)(cid:4)/ = (cid:4)(cid:30)(cid:15)/ 3(cid:23)(cid:23)&(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) 7 (cid:4)(cid:30)(cid:5)/ (cid:4)(cid:30);(cid:4) (cid:4)(cid:30)(cid:18)/ 3(cid:23)(cid:23)&(cid:10)(cid:22)(cid:20)(cid:26)& 7(cid:15) (cid:15)(cid:30)(cid:4)(cid:4)(cid:14)(cid:8).3 3(cid:23)(cid:23)&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13) (cid:3) (cid:4)> (cid:16)(cid:30)/> (cid:18)> 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)?(cid:20)#&(cid:24) . (cid:15)(cid:5)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2) (cid:15)(cid:5)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)?(cid:20)#&(cid:24) .(cid:15) (cid:15)(cid:17)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2)(cid:15) (cid:15)(cid:17)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 7(cid:13)(cid:11)#(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:21) (cid:4)(cid:30)(cid:4)(cid:6) = (cid:4)(cid:30)(cid:17)(cid:4) 7(cid:13)(cid:11)#(cid:14)?(cid:20)#&(cid:24) ) (cid:4)(cid:30)(cid:15)(cid:16) (cid:4)(cid:30)(cid:15)@ (cid:4)(cid:30)(cid:17)(cid:16) (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)(cid:25)(cid:23)(cid:10) (cid:4) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)1(cid:23)&&(cid:23)’ (cid:5) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> ’ (cid:13)(cid:6)(cid:12)( (cid:15)(cid:30) (cid:31)(cid:20)(cid:26)(cid:14)(cid:15)(cid:14) (cid:20)!"(cid:11)(cid:27)(cid:14)(cid:20)(cid:26)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:22)(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)*(cid:20)&(cid:24)(cid:20)(cid:26)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:24)(cid:11)&(cid:21)(cid:24)(cid:13)#(cid:14)(cid:11)(cid:22)(cid:13)(cid:11)(cid:30) (cid:17)(cid:30) +(cid:24)(cid:11)’%(cid:13)(cid:22)!(cid:14)(cid:11)&(cid:14)(cid:21)(cid:23)(cid:22)(cid:26)(cid:13)(cid:22)!(cid:14)(cid:11)(cid:22)(cid:13)(cid:14)(cid:23)(cid:10)&(cid:20)(cid:23)(cid:26)(cid:11)(cid:27),(cid:14)!(cid:20)-(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)(cid:30) (cid:16)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)!(cid:14)(cid:2)(cid:15)(cid:14)(cid:11)(cid:26)#(cid:14).(cid:15)(cid:14)#(cid:23)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:20)(cid:26)(cid:21)(cid:27)"#(cid:13)(cid:14)’(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:30)(cid:14)(cid:19)(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:14)!(cid:24)(cid:11)(cid:27)(cid:27)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:13)$(cid:21)(cid:13)(cid:13)#(cid:14)(cid:4)(cid:30)(cid:17)/(cid:14)’’(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)!(cid:20)#(cid:13)(cid:30) (cid:5)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:20)(cid:26)(cid:12)(cid:14)(cid:11)(cid:26)#(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:20)(cid:26)(cid:12)(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)(cid:7)(cid:3)(cid:19).(cid:14)0(cid:15)(cid:5)(cid:30)/(cid:19)(cid:30) 1(cid:3)+2 1(cid:11)!(cid:20)(cid:21)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:30)(cid:14)(cid:25)(cid:24)(cid:13)(cid:23)(cid:22)(cid:13)&(cid:20)(cid:21)(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)(cid:13)$(cid:11)(cid:21)&(cid:14) (cid:11)(cid:27)"(cid:13)(cid:14)!(cid:24)(cid:23)*(cid:26)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)!(cid:30) (cid:8).32 (cid:8)(cid:13)%(cid:13)(cid:22)(cid:13)(cid:26)(cid:21)(cid:13)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)((cid:14)"!"(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)((cid:14)%(cid:23)(cid:22)(cid:14)(cid:20)(cid:26)%(cid:23)(cid:22)’(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:10)"(cid:22)(cid:10)(cid:23)!(cid:13)!(cid:14)(cid:23)(cid:26)(cid:27)(cid:28)(cid:30) (cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:25)(cid:13)(cid:21)(cid:24)(cid:26)(cid:23)(cid:27)(cid:23)(cid:12)(cid:28)(cid:2)(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)+(cid:4)(cid:5)(cid:9)(cid:15)(cid:4)(cid:4)1 DS39905E-page 314  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY (cid:27)(cid:28)(cid:28)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:16)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)#(cid:29)(cid:27)#(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)  2010 Microchip Technology Inc. DS39905E-page 315

PIC24FJ256GA110 FAMILY (cid:27)(cid:28)(cid:28)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:21)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)(cid:3)(cid:29)(cid:27)(cid:3)(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12) D D1 e E1 E b N α NOTE1 123 NOTE2 A φ c A2 β A1 L L1 6(cid:26)(cid:20)&! (cid:19)(cid:29)77(cid:29)(cid:19).(cid:25).(cid:8)(cid:3) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:14)7(cid:20)’(cid:20)&! (cid:19)(cid:29)8 89(cid:19) (cid:19)(cid:7): 8"’)(cid:13)(cid:22)(cid:14)(cid:23)%(cid:14)7(cid:13)(cid:11)#! 8 (cid:15)(cid:4)(cid:4) 7(cid:13)(cid:11)#(cid:14)(cid:31)(cid:20)&(cid:21)(cid:24) (cid:13) (cid:4)(cid:30)/(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)<(cid:13)(cid:20)(cid:12)(cid:24)& (cid:7) = = (cid:15)(cid:30)(cid:17)(cid:4) (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:7)(cid:17) (cid:4)(cid:30)(cid:6)/ (cid:15)(cid:30)(cid:4)(cid:4) (cid:15)(cid:30)(cid:4)/ (cid:3)&(cid:11)(cid:26)#(cid:23)%%(cid:14)(cid:14) (cid:7)(cid:15) (cid:4)(cid:30)(cid:4)/ = (cid:4)(cid:30)(cid:15)/ 3(cid:23)(cid:23)&(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) 7 (cid:4)(cid:30)(cid:5)/ (cid:4)(cid:30);(cid:4) (cid:4)(cid:30)(cid:18)/ 3(cid:23)(cid:23)&(cid:10)(cid:22)(cid:20)(cid:26)& 7(cid:15) (cid:15)(cid:30)(cid:4)(cid:4)(cid:14)(cid:8).3 3(cid:23)(cid:23)&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13) (cid:3) (cid:4)> (cid:16)(cid:30)/> (cid:18)> 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)?(cid:20)#&(cid:24) . (cid:15);(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 9 (cid:13)(cid:22)(cid:11)(cid:27)(cid:27)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2) (cid:15);(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)?(cid:20)#&(cid:24) .(cid:15) (cid:15)(cid:5)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ (cid:19)(cid:23)(cid:27)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)7(cid:13)(cid:26)(cid:12)&(cid:24) (cid:2)(cid:15) (cid:15)(cid:5)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3)+ 7(cid:13)(cid:11)#(cid:14)(cid:25)(cid:24)(cid:20)(cid:21)4(cid:26)(cid:13)!! (cid:21) (cid:4)(cid:30)(cid:4)(cid:6) = (cid:4)(cid:30)(cid:17)(cid:4) 7(cid:13)(cid:11)#(cid:14)?(cid:20)#&(cid:24) ) (cid:4)(cid:30)(cid:15)(cid:18) (cid:4)(cid:30)(cid:17)(cid:17) (cid:4)(cid:30)(cid:17)(cid:18) (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)(cid:25)(cid:23)(cid:10) (cid:4) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> (cid:19)(cid:23)(cid:27)#(cid:14)(cid:2)(cid:22)(cid:11)%&(cid:14)(cid:7)(cid:26)(cid:12)(cid:27)(cid:13)(cid:14)1(cid:23)&&(cid:23)’ (cid:5) (cid:15)(cid:15)> (cid:15)(cid:17)> (cid:15)(cid:16)> ’ (cid:13)(cid:6)(cid:12)( (cid:15)(cid:30) (cid:31)(cid:20)(cid:26)(cid:14)(cid:15)(cid:14) (cid:20)!"(cid:11)(cid:27)(cid:14)(cid:20)(cid:26)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:22)(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)*(cid:20)&(cid:24)(cid:20)(cid:26)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:24)(cid:11)&(cid:21)(cid:24)(cid:13)#(cid:14)(cid:11)(cid:22)(cid:13)(cid:11)(cid:30) (cid:17)(cid:30) +(cid:24)(cid:11)’%(cid:13)(cid:22)!(cid:14)(cid:11)&(cid:14)(cid:21)(cid:23)(cid:22)(cid:26)(cid:13)(cid:22)!(cid:14)(cid:11)(cid:22)(cid:13)(cid:14)(cid:23)(cid:10)&(cid:20)(cid:23)(cid:26)(cid:11)(cid:27),(cid:14)!(cid:20)-(cid:13)(cid:14)’(cid:11)(cid:28)(cid:14) (cid:11)(cid:22)(cid:28)(cid:30) (cid:16)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)!(cid:14)(cid:2)(cid:15)(cid:14)(cid:11)(cid:26)#(cid:14).(cid:15)(cid:14)#(cid:23)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:20)(cid:26)(cid:21)(cid:27)"#(cid:13)(cid:14)’(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:30)(cid:14)(cid:19)(cid:23)(cid:27)#(cid:14)%(cid:27)(cid:11)!(cid:24)(cid:14)(cid:23)(cid:22)(cid:14)(cid:10)(cid:22)(cid:23)&(cid:22)"!(cid:20)(cid:23)(cid:26)!(cid:14)!(cid:24)(cid:11)(cid:27)(cid:27)(cid:14)(cid:26)(cid:23)&(cid:14)(cid:13)$(cid:21)(cid:13)(cid:13)#(cid:14)(cid:4)(cid:30)(cid:17)/(cid:14)’’(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)!(cid:20)#(cid:13)(cid:30) (cid:5)(cid:30) (cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:20)(cid:26)(cid:12)(cid:14)(cid:11)(cid:26)#(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:20)(cid:26)(cid:12)(cid:14)(cid:10)(cid:13)(cid:22)(cid:14)(cid:7)(cid:3)(cid:19).(cid:14)0(cid:15)(cid:5)(cid:30)/(cid:19)(cid:30) 1(cid:3)+2 1(cid:11)!(cid:20)(cid:21)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)(cid:30)(cid:14)(cid:25)(cid:24)(cid:13)(cid:23)(cid:22)(cid:13)&(cid:20)(cid:21)(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)(cid:13)$(cid:11)(cid:21)&(cid:14) (cid:11)(cid:27)"(cid:13)(cid:14)!(cid:24)(cid:23)*(cid:26)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)!(cid:30) (cid:8).32 (cid:8)(cid:13)%(cid:13)(cid:22)(cid:13)(cid:26)(cid:21)(cid:13)(cid:14)(cid:2)(cid:20)’(cid:13)(cid:26)!(cid:20)(cid:23)(cid:26)((cid:14)"!"(cid:11)(cid:27)(cid:27)(cid:28)(cid:14)*(cid:20)&(cid:24)(cid:23)"&(cid:14)&(cid:23)(cid:27)(cid:13)(cid:22)(cid:11)(cid:26)(cid:21)(cid:13)((cid:14)%(cid:23)(cid:22)(cid:14)(cid:20)(cid:26)%(cid:23)(cid:22)’(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:10)"(cid:22)(cid:10)(cid:23)!(cid:13)!(cid:14)(cid:23)(cid:26)(cid:27)(cid:28)(cid:30) (cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:25)(cid:13)(cid:21)(cid:24)(cid:26)(cid:23)(cid:27)(cid:23)(cid:12)(cid:28)(cid:2)(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)+(cid:4)(cid:5)(cid:9)(cid:15)(cid:15)(cid:4)1 DS39905E-page 316  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY (cid:27)(cid:28)(cid:28)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:14)(cid:18)(cid:9)(cid:19)(cid:20)(cid:7)(cid:8)(cid:9)(cid:21)(cid:11)(cid:7)(cid:13)(cid:22)(cid:7)(cid:15)(cid:23)(cid:9)(cid:24)(cid:10)(cid:21)(cid:25)(cid:9)(cid:26)(cid:9)(cid:27)(cid:3)(cid:29)(cid:27)(cid:3)(cid:29)(cid:27)(cid:9)(cid:30)(cid:30)(cid:9)(cid:31) (cid:8)!"(cid:9)#$(cid:28)(cid:28)(cid:9)(cid:30)(cid:30)(cid:9)%(cid:16)(cid:19)(cid:21)(cid:10)& ’ (cid:13)(cid:6)( 3(cid:23)(cid:22)(cid:14)&(cid:24)(cid:13)(cid:14)’(cid:23)!&(cid:14)(cid:21)"(cid:22)(cid:22)(cid:13)(cid:26)&(cid:14)(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:22)(cid:11)*(cid:20)(cid:26)(cid:12)!((cid:14)(cid:10)(cid:27)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:24)(cid:13)(cid:14)(cid:19)(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:14)(cid:31)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:21)(cid:20)%(cid:20)(cid:21)(cid:11)&(cid:20)(cid:23)(cid:26)(cid:14)(cid:27)(cid:23)(cid:21)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:24)&&(cid:10)255***(cid:30)’(cid:20)(cid:21)(cid:22)(cid:23)(cid:21)(cid:24)(cid:20)(cid:10)(cid:30)(cid:21)(cid:23)’5(cid:10)(cid:11)(cid:21)4(cid:11)(cid:12)(cid:20)(cid:26)(cid:12)  2010 Microchip Technology Inc. DS39905E-page 317

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 318  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY APPENDIX A: REVISION HISTORY Updates Section25.5 “JTAG Interface” to remove references to programming via the interface. Revision A (December 2007) Makes multiple additions and changes to Section28.0 “Electrical Characteristics”, including: Original data sheet for the PIC24FJ256GA110 family of • DC current characteristics for extended devices. temperature operation (125°C) Revision B (February 2008) • New DC characteristics of VBOR, VBG, TBG and ICNPD Updates to Section28.0 “Electrical Characteristics” • Addition of new VPEW specification for VDDCORE and minor edits to text throughout document. • New AC characteristics for internal oscillator start-up time (TLPRC) Revision C (April 2009) • Combination of all Internal RC Accuracy information into a single table Updates to all Pin Diagrams to reflect the correct order of priority for multiplexed peripherals and adds the Makes other minor typographic corrections throughout ASCK1 pin function. the text. Adds packaging information for the new 64-pin QFN package to Section29.0 “Packaging Information” Revision D (December 2009) and the Product Information System. Updates Section2.0 “Guidelines for Getting Started Updates Section5.0 “Flash Program Memory” with with 16-bit Microcontrollers” with the most current revised code examples in assembler and new code version. examples in C. Corrects annotations to the CN70 pin function in Updates Section6.2 “Device Reset Times” with Table4-4 of Section4.2.4 “SFR Space”. revised information, particularly Table6-3. Corrects annotations to remappable output function 30 Adds the INTTREG register to Section4.0 “Memory in Register10-37 of Section10.4 “Peripheral Pin Organization” and Section7.0 “Interrupt Controller”. Select”. Makes several additions and changes to Section10.0 Corrects the definitions for the WPEND and “I/O Ports”, including: WPFP<7:0> Configuration bits in Register25-3 of • revision of Section10.4.2.1 “Peripheral Pin Section25.1 “Configuration Bits”. Select Function Priority” Updates Section28.0 “Electrical Characteristics” • addition of Section10.4.3.3 “Alternate Fixed with additional data for IDD at 60°C. Also corrects Pin Mapping” occurrences of “DISVREG” throughout the chapter, • revisions to Table10-3, “Selectable Output replacing them with “ENVREG” and the proper Sources” VDD/VSS connection information. • addition of the ALTRP register (and in Section4.0 Makes other minor typographic corrections throughout “Memory Organization”) the text. Updates Section15.0 “Serial Peripheral Interface Revision E (November 2010) (SPI)” to include references to the ASCK1 pin function. Updates Section 20.0 “Programmable Cyclic Updated Section2.0 “Guidelines for Getting Started Redundancy Check (CRC) Generator” with new with 16-bit Microcontrollers” with the most current illustrations and a revised Section 20.1 “User version. Interface”. Updates to Section28.0 “Electrical Characteristics” Updates Section21.0 “10-Bit High-Speed A/D Con- with tables being added and replaced from the FRM verter” by changing all references to AD1CHS0 to chapters. AD1CHS (as well as other locations in the document). Also revises bit field descriptions in registers: AD1CON3 (bits 7:0) and AD1CHS (bits 12:8). Makes minor text edits to bit descriptions in Section22.0 “Triple Comparator Module” (Register22-1) and Section24.0 “Charge Time Measurement Unit (CTMU)” (Register24-1). Updates Section25.2 “On-Chip Voltage Regulator” with revised text on the operation of the regulator during POR and Standby mode.  2010 Microchip Technology Inc. DS39905E-page 319

PIC24FJ256GA110 FAMILY Revision E (November 2010) Added 64-Kbyte device variants – PIC24FJ64GA106, PIC24FJ64GA108 and PIC24FJ64GA110. Changed the CON bit to CEN to match other existing PIC24F, PIC24H and dsPIC® products. Changed the VREFS bit to PMSLP to match other existing PIC24F, PIC24H and dsPIC® products. Corrected the OCxCON2 and ICxCON2 Reset values in the register descriptions. Defined SOSC and RTCC behavior during MCLR events. Corrected the RCFGCAL Reset values in the register descriptions. Updated Configuration Word unprogrammed information to more accurately reflect the devices’ behavior. Added electrical specifications from the “PIC24F Family Reference Manual”. Corrected errors in the ENVREG pin operation descriptions. Other minor typographic corrections throughout the document. DS39905E-page 320  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY INDEX A Reset System ............................................................65 RTCC .......................................................................211 A/D Converter Shared I/O Port Structure ........................................127 Analog Input Model ..................................................233 SPI Master, Frame Master Connection ...................183 Transfer Function .....................................................234 SPI Master, Frame Slave Connection .....................183 AC Characteristics SPI Master/Slave Connection A/D Specifications ....................................................286 (Enhanced Buffer Modes) ................................182 Capacitive Loading Requirements on SPI Master/Slave Connection (Standard Mode) ......182 Output Pins ......................................................282 SPI Slave, Frame Master Connection .....................183 CLKO and I/O Requirements ...................................285 SPI Slave, Frame Slave Connection .......................183 Conversion Timing Requirements ............................287 SPIx Module (Enhanced Mode) ...............................177 External Clock Requirements ..................................283 SPIx Module (Standard Mode) ................................176 Internal RC Oscillator Accuracy ...............................284 System Clock ...........................................................115 Internal RC Oscillator Specifications ........................284 Timer1 .....................................................................155 Load Conditions and Requirements for Timer2 and Timer4 (16-Bit Synchronous) ...............159 Specifications ...................................................282 Timer2/3 and Timer4/5 (32-Bit) ...............................158 PLL Clock Specifications .........................................284 Timer3 and Timer5 (16-Bit Asynchronous) ..............159 Reset Specifications ................................................285 Triple Comparator Module .......................................235 Reset, Watchdog Timer, Oscillator Start-up Typical CTMU Connections and Internal Timer, Power-up Timer, Brown-out Reset Configuration for Capacitance Measurement ....241 Requirements ..................................................288 Typical CTMU Connections and Internal AC Specifications .............................................................289 Configuration for Pulse Delay Generation .......242 Alternate Interrupt Vector Table (AIVT) .............................71 Typical CTMU Connections and Internal Assembler Configuration for Time Measurement ..............242 MPASM Assembler ..................................................266 UART (Simplified) ....................................................193 B Watchdog Timer (WDT) ...........................................253 Block Diagrams C 10-Bit High-Speed A/D Converter ............................226 C Compilers 8-Bit Multiplexed Address and Data Application ......210 MPLAB C18 .............................................................266 Accessing Program Space Using Table Charge Time Measurement Unit. See CTMU. Instructions ........................................................55 Clock Frequency ..............................................................125 Addressable Parallel Slave Port Example ...............208 Clock Switching ...............................................................125 Addressing for Table Registers ..................................57 Code Examples CALL Stack Frame .....................................................53 Basic Sequence for Clock Switching .......................121 Comparator Voltage Reference ...............................239 Configuring UART1 Input and Output Functions .....134 CPU Programmer’s Model .........................................31 Erasing a Program Memory Block, Assembly ...........60 CRC Module ............................................................221 Erasing a Program Memory Block, C Language .......61 CRC Shift Engine .....................................................222 I/O Port Read/Write .................................................128 CTMU Current Source Calibration Circuit ................281 I2C Module ...............................................................186 Initiating a Programming Sequence, Assembly .........62 Initiating a Programming Sequence, C Language .....62 Individual Comparator Configurations ......................236 Loading the Write Buffers, Assembly ........................61 Input Capture ...........................................................163 Loading the Write Buffers, C Language ....................62 LCD Control (Byte Mode) .........................................210 Setting the RTCWREN Bit .......................................212 Legacy Parallel Slave Port Example ........................208 Single-Word Flash Programming, Assembly .............63 Master Mode, Demultiplexed Addressing Single-Word Flash Programming, C Language .........63 (Separate Read and Write Strobes) ................208 Code Protection ...............................................................253 Master Mode, Fully Multiplexed Addressing Code Segment .........................................................254 (Separate Read and Write Strobes) ................209 Configuration Options ......................................254 Master Mode, Partially Multiplexed Addressing Configuration Registers ...........................................254 (Separate Read and Write Strobes) ................209 General Segment ....................................................253 Multiplexed Addressing Application .........................209 Comparator Voltage Reference Module ..........................239 On-Chip Regulator Connections ..............................251 Configuring ..............................................................239 Output Compare (16-Bit Mode) ................................168 Configuration Bits ............................................................245 Output Compare (Double-Buffered, CPU 16-Bit PWM Mode) ..........................................170 ALU ............................................................................34 Parallel EEPROM (15-Bit Address, 8-Bit Data) .......210 Control Registers .......................................................32 Parallel EEPROM (15-Bit Address,16-Bit Data) ......210 Core Registers ...........................................................31 Partially Multiplexed Addressing Application ...........210 CRC PCI24FJ256GA110 Family (General) ........................14 Operation in Power Save Modes .............................222 PIC24F CPU Core .....................................................30 Setup Example ........................................................221 PMP Module Overview ............................................201 User Interface ..........................................................222 Program Space Address Generation .........................54 PSV Operation ...........................................................56  2010 Microchip Technology Inc. DS39905E-page 321

PIC24FJ256GA110 FAMILY CTMU I Measuring Capacitance ...........................................241 I/O Ports ...........................................................................127 Measuring Time .......................................................242 Analog Port Configuration ........................................128 Pulse Generation and Delay ....................................242 Configuring Analog Pins ..........................................128 Customer Change Notification Service ............................326 Input Change Notification ........................................129 Customer Notification Service ..........................................326 Open-Drain Configuration ........................................128 Customer Support ............................................................326 Parallel (PIO) ...........................................................127 D Peripheral Pin Select ...............................................129 Pull-ups and Pull-Downs ..........................................129 Data Memory I2C Address Space ...........................................................37 Clock Rates .............................................................187 Memory Map ..............................................................37 Communicating as Master in Single Master Near Data Space .......................................................38 Environment ....................................................185 SFR Space .................................................................38 Peripheral Remapping Options ................................185 Software Stack ...........................................................53 Reserved Addresses ...............................................187 Space Organization, Alignment .................................38 Setting Baud Rate When Operating as DC Characteristics Bus Master ......................................................187 I/O Pin Input Specifications ......................................278 Slave Address Masking ...........................................187 I/O Pin Output Specifications ...................................279 Input Capture Idle Current ..............................................................274 32-Bit Cascaded Mode ............................................164 Internal Voltage Regulator Specifications ................280 Operations ...............................................................164 Operating Current ....................................................273 Synchronous and Trigger Modes .............................163 Power-Down Current ...............................................276 Input Capture with Dedicated Timer ................................163 Program Memory .....................................................280 Instruction Set Temperature and Voltage Specifications .................271 Overview ..................................................................259 Development Support ......................................................265 Summary .................................................................257 Device Features (Summary) Inter-Integrated Circuit (I2C) ............................................185 100-Pin .......................................................................13 Inter-Integrated Circuit. See I2C. 64-Pin .........................................................................11 Internet Address ..............................................................326 80-Pin .........................................................................12 Interrupt Controller .............................................................71 Device Overview Interrupt Vector Table (IVT) ...............................................71 Core Features ..............................................................9 Interrupts Family Member Details ..............................................10 Implemented Vectors .................................................73 Other Special Features ..............................................10 Reset Sequence ........................................................71 E Setup and Service Procedures ................................113 Trap Vectors ..............................................................72 Electrical Characteristics ..................................................269 Vector Table ..............................................................72 Absolute Maximum Ratings .....................................269 Thermal Operating Conditions .................................270 J V/F Graph ................................................................270 JTAG Interface .................................................................255 ENVREG Pin ....................................................................251 Equations M A/D Conversion Clock Period ..................................233 Microchip Internet Web Site .............................................326 Calculating the PWM Period ....................................170 MPLAB ASM30 Assembler, Linker, Librarian ..................266 Calculation for Maximum PWM Resolution ..............171 MPLAB Integrated Development Environment Computing Baud Rate Reload Value .......................187 Software ..................................................................265 Relationship Between Device and MPLAB PM3 Device Programmer ...................................268 SPI Clock Speed ..............................................184 MPLAB REAL ICE In-Circuit Emulator System ...............267 RTCC Calibration .....................................................219 MPLINK Object Linker/MPLIB Object Librarian ...............266 UART Baud Rate with BRGH = 0 ............................194 UART Baud Rate with BRGH = 1 ............................194 N Errata ...................................................................................8 Near Data Space ...............................................................38 F O Flash Configuration Words .................................................36 Oscillator Configuration Flash Program Memory Bit Values for Clock Selection ..................................116 and Table Instructions ................................................57 Clock Switching .......................................................120 Enhanced ICSP Operation .........................................58 Sequence ........................................................121 JTAG Operation .........................................................58 CPU Clocking Scheme ............................................116 Operations .................................................................58 Initial Configuration on POR ....................................116 Programming Algorithm .............................................60 Reference Clock Output ..........................................122 RTSP Operation .........................................................58 Single-Word Programming .........................................63 DS39905E-page 322  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY Output Compare Peripheral Pin Select .................................................51 Cascaded (32-Bit) Mode ..........................................167 PMD ...........................................................................52 Operations ...............................................................168 PORTA ......................................................................47 Synchronous and Trigger Modes .............................167 PORTB ......................................................................47 Output Compare with Dedicated Timer ............................167 PORTC ......................................................................47 PORTD ......................................................................47 P PORTE ......................................................................48 Packaging ........................................................................305 PORTF ......................................................................48 Details ......................................................................307 Real-Time Clock and Calendar .................................50 Marking ....................................................................305 SPI .............................................................................46 Parallel Master Port. See PMP. .......................................201 System .......................................................................52 Peripheral Enable Bits .....................................................126 Timers ........................................................................42 Peripheral Module Disable Bits ........................................126 UART .........................................................................46 Peripheral Pin Select (PPS) .............................................129 Registers Alternate Fixed Pin Mapping ....................................130 AD1CHS (A/D Input Select) .....................................230 Available Peripherals and Pins ................................130 AD1CON1 (A/D Control 1) .......................................227 Configuration Control ...............................................133 AD1CON2 (A/D Control 2) .......................................228 Considerations for Use ............................................134 AD1CON3 (A/D Control 3) .......................................229 Input Mapping ..........................................................130 AD1CSSL (A/D Input Scan Select Low) ..................232 Mapping Exceptions .................................................133 AD1PCFGH (A/D Port Configuration High) .............231 Output Mapping .......................................................130 AD1PCFGL (A/D Port Configuration Low) ...............231 Peripheral Priority ....................................................130 ALCFGRPT (Alarm Configuration) ..........................215 Pinout Descriptions ......................................................15–22 ALMINSEC (Alarm Minutes and Seconds Value) ....219 PMSLP Bit ..........................................................................66 ALMTHDY (Alarm Month and Day Value) ...............218 and Wake-up Time ...................................................125 ALTRP (Alternate Peripheral Pin Mapping) .............154 PMSLP bit ALWDHR (Alarm Weekday and Hours Value) ........218 and Wake-up Time ...................................................252 CLKDIV (Clock Divider) ...........................................119 Power-Saving Features ...................................................125 CMSTAT (Comparator Status) ................................238 Modes CMxCON (Comparator x Control) ...........................237 Doze ................................................................126 CORCON (CPU Control) .....................................33, 75 Idle ...................................................................126 CRCCON (CRC Control) .........................................223 Sleep ................................................................125 CRCXOR (CRC XOR Polynomial) ..........................224 Power-up Requirements ..................................................252 CTMUCON (CTMU Control) ....................................243 Product Identification System ..........................................328 CTMUICON (CTMU Current Control) ......................244 Program Memory CVRCON (Comparator Voltage Reference Access Using Table Instructions ................................55 Control) ............................................................240 Address Space ...........................................................35 CW1 (Flash Configuration Word 1) .........................246 Addressing .................................................................53 CW2 (Flash Configuration Word 2) .........................248 Flash Configuration Words ........................................36 CW3 (Flash Configuration Word 3) .........................249 Memory Maps ............................................................35 DEVID (Device ID) ...................................................250 Organization ...............................................................36 DEVREV (Device Revision) .....................................250 Program Space Visibility ............................................56 I2CxCON (I2Cx Control) ..........................................188 Program Space Visibility (PSV) .........................................56 I2CxMSK (I2Cx Slave Mode Address Mask) ...........192 Program Verification ........................................................253 I2CxSTAT (I2Cx Status) ..........................................190 Programmer’s Model ..........................................................29 ICxCON1 (Input Capture x Control 1) ......................165 Pulse-Width Modulation (PWM) Mode .............................169 ICxCON2 (Input Capture x Control 2) ......................166 Pulse-Width Modulation. See PWM. IEC0 (Interrupt Enable Control 0) ..............................84 PWM IEC1 (Interrupt Enable Control 1) ..............................85 Duty Cycle and Period .............................................170 IEC2 (Interrupt Enable Control 2) ..............................87 IEC3 (Interrupt Enable Control 3) ..............................88 R IEC4 (Interrupt Enable Control 4) ..............................89 Reader Response ............................................................327 IEC5 (Interrupt Enable Control 5) ..............................90 Register Maps IFS0 (Interrupt Flag Status 0) ....................................78 ADC ...........................................................................49 IFS1 (Interrupt Flag Status 1) ....................................79 Comparators ..............................................................50 IFS2 (Interrupt Flag Status 2) ....................................80 CPU Core ...................................................................39 IFS3 (Interrupt Flag Status 3) ....................................81 CRC ...........................................................................50 IFS4 (Interrupt Flag Status 4) ....................................82 CTMU .........................................................................49 IFS5 (Interrupt Flag Status 5) ....................................83 I2C ..............................................................................45 INTCON1 (Interrupt Control 1) ..................................76 ICN .............................................................................40 INTCON2 (Interrupt Control 2) ..................................77 Input Capture .............................................................43 INTTREG (Interrupt Control and Status) .................112 Interrupt Controller .....................................................41 IPC0 (Interrupt Priority Control 0) ..............................91 NVM ...........................................................................52 IPC1 (Interrupt Priority Control 1) ..............................92 Output Compare ........................................................44 IPC10 (Interrupt Priority Control 10) ........................101 Pad Configuration ......................................................48 IPC11 (Interrupt Priority Control 11) ........................102 Parallel Master/Slave Port .........................................50  2010 Microchip Technology Inc. DS39905E-page 323

PIC24FJ256GA110 FAMILY IPC12 (Interrupt Priority Control 12) ........................103 RPOR3 (PPS Output 3) ...........................................147 IPC13 (Interrupt Priority Control 13) ........................104 RPOR4 (PPS Output 4) ...........................................148 IPC15 (Interrupt Priority Control 15) ........................105 RPOR5 (PPS Output 5) ...........................................148 IPC16 (Interrupt Priority Control 16) ........................106 RPOR6 (PPS Output 6) ...........................................149 IPC18 (Interrupt Priority Control 18) ........................107 RPOR7 (PPS Output 7) ...........................................149 IPC19 (Interrupt Priority Control 19) ........................107 RPOR8 (PPS Output 8) ...........................................150 IPC2 (Interrupt Priority Control 2) ..............................93 RPOR9 (PPS Output 9) ...........................................150 IPC20 (Interrupt Priority Control 20) ........................108 SPIxCON1 (SPIx Control 1) .....................................180 IPC21 (Interrupt Priority Control 21) ........................109 SPIxCON2 (SPIx Control 2) .....................................181 IPC22 (Interrupt Priority Control 22) ........................110 SPIxSTAT (SPIx Status and Control) ......................178 IPC23 (Interrupt Priority Control 23) ........................111 SR (ALU STATUS, in CPU) .......................................75 IPC3 (Interrupt Priority Control 3) ..............................94 SR (ALU STATUS) ....................................................32 IPC4 (Interrupt Priority Control 4) ..............................95 T1CON (Timer1 Control) .........................................156 IPC5 (Interrupt Priority Control 5) ..............................96 TxCON (Timer2 and Timer4 Control) ......................160 IPC6 (Interrupt Priority Control 6) ..............................97 TyCON (Timer3 and Timer5 Control) ......................161 IPC7 (Interrupt Priority Control 7) ..............................98 UxMODE (UARTx Mode) .........................................196 IPC8 (Interrupt Priority Control 8) ..............................99 UxSTA (UARTx Status and Control) ........................198 IPC9 (Interrupt Priority Control 9) ............................100 WKDYHR (RTCC Weekday and Hours Value) ........217 MINSEC (RTCC Minutes and Seconds Value) ........217 YEAR (RTCC Year Value) .......................................216 MTHDY (RTCC Month and Day Value) ...................216 Registers Maps NVMCON (Flash Memory Control) ............................59 PORTG ......................................................................48 OCxCON1 (Output Compare x Control 1) ...............172 Resets OCxCON2 (Output Compare x Control 2) ...............173 Clock Source Selection ..............................................67 OSCCON (Oscillator Control) ..................................117 Delay Times ...............................................................68 OSCTUN (FRC Oscillator Tune) ..............................120 RCON Flag Operation ...............................................67 PADCFG1 (Pad Configuration Control) ...........207, 214 SFR States ................................................................69 PMADDR (PMP Address) ........................................205 Revision History ...............................................................319 PMAEN (PMP Enable) .............................................205 RTCC PMCON (PMP Control) ............................................202 Alarm Configuration .................................................220 PMMODE (PMP Mode) ............................................204 Calibration ...............................................................219 PMSTAT (PMP Status) ............................................206 Register Mapping .....................................................212 RCFGCAL (RTCC Calibration and S Configuration) ..................................................213 RCON (Reset Control) ...............................................66 Selective Peripheral Power Control .................................126 REFOCON (Reference Oscillator Control) ...............123 Serial Peripheral Interface. See SPI. RPINR0 (Peripheral Pin Select Input 0) ...................135 SFR Space ........................................................................38 RPINR1 (Peripheral Pin Select Input 1) ...................135 Software Simulator (MPLAB SIM) ...................................267 RPINR10 (Peripheral Pin Select Input 10) ...............139 Software Stack ...................................................................53 RPINR11 (Peripheral Pin Select Input 11) ...............139 SPI RPINR15 (Peripheral Pin Select Input 15) ...............140 Symbols Used in Opcode Descriptions ...........................258 RPINR17 (Peripheral Pin Select Input 17) ...............140 T RPINR18 (Peripheral Pin Select Input 18) ...............141 RPINR19 (Peripheral Pin Select Input 19) ...............141 Timer1 ..............................................................................155 RPINR2 (Peripheral Pin Select Input 2) ...................136 Timer2/3 and Timer4/5 RPINR20 (Peripheral Pin Select Input 20) ...............142 Timing Diagrams RPINR21 (Peripheral Pin Select Input 21) ...............142 Baud Rate Generator Output ...................................289 RPINR22 (Peripheral Pin Select Input 22) ...............143 CLKO and I/O Characteristics .................................285 RPINR23 (Peripheral Pin Select Input 23) ...............143 External Clock Requirements ..................................283 RPINR27 (Peripheral Pin Select Input 27) ...............144 I2C Bus Data (Master Mode) ...................................297 RPINR28 (Peripheral Pin Select Input 28) ...............144 I2C Bus Data (Slave Mode) .....................................299 RPINR29 (Peripheral Pin Select Input 29) ...............145 I2C Bus Start/Stop Bits (Master Mode) ....................296 RPINR3 (Peripheral Pin Select Input 3) ...................136 I2C Bus Start/Stop Bits (Slave Mode) ......................298 RPINR4 (Peripheral Pin Select Input 4) ...................137 Input Capture ...........................................................290 RPINR7 (Peripheral Pin Select Input 7) ...................137 Output Compare ......................................................295 RPINR8 (Peripheral Pin Select Input 8) ...................138 Parallel Master Port Read ........................................301 RPINR9 (Peripheral Pin Select Input 9) ...................138 Parallel Master Port Write ........................................302 RPOR0 (PPS Output 0) ...........................................146 PWM Requirements .................................................295 RPOR1 (PPS Output 1) ...........................................146 Reset, Watchdog Timer. Oscillator Start-up RPOR10 (PPS Output 10) .......................................151 Timer, Power-up Timer Characteristics .....272, 288 RPOR11 (PPS Output 11) .......................................151 SPIx Master Mode (CKE = 0) ..................................291 RPOR12 (PPS Output 12) .......................................152 SPIx Master Mode (CKE = 1) ..................................292 RPOR13 (PPS Output 13) .......................................152 SPIx Slave Mode (CKE = 0) ....................................293 RPOR14 (PPS Output 14) .......................................153 SPIx Slave Mode (CKE = 1) ....................................294 RPOR15 (PPS Output 15) .......................................153 Start Bit Edge Detection ..........................................289 RPOR2 (PPS Output 2) ...........................................147 DS39905E-page 324  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY Timing Requirements V Comparator ..............................................................303 VDDCORE/VCAP Pin ..........................................................251 DC ............................................................................303 Voltage Regulator (On-Chip) ...........................................251 I2C Bus Data (Master Mode) ............................296, 297 and BOR ..................................................................252 I2C Bus Data (Slave Mode) ......................................299 and POR ..................................................................252 I2C Bus Start/Stop Bit (Slave Mode) ........................298 Standby Mode .........................................................252 Input Capture ...........................................................290 Tracking Mode .........................................................251 Output Compare ......................................................295 Parallel Master Port Read ........................................301 W Parallel Master Port Write ........................................302 Watchdog Timer (WDT) ...................................................252 Parallel Slave Port ...................................................300 Control Register .......................................................253 SPIx Master Mode (CKE = 0) ..................................291 Windowed Operation ...............................................253 SPIx Master Mode (CKE = 1) ..................................292 WWW Address ................................................................326 SPIx Slave Mode (CKE = 0) ....................................293 WWW, On-Line Support ......................................................8 SPIx Slave Mode (CKE = 1) ....................................294 Triple Comparator Module ...............................................235 U UART ...............................................................................193 Baud Rate Generator (BRG) ....................................194 IrDA Support ............................................................195 Operation of UxCTS and UxRTS Pins .....................195 Receiving .................................................................195 Transmitting 8-Bit Data Mode ...............................................195 9-Bit Data Mode ...............................................195 Break and Sync Sequence ..............................195 Universal Asynchronous Receiver Transmitter. See UART.  2010 Microchip Technology Inc. DS39905E-page 325

PIC24FJ256GA110 FAMILY NOTES: DS39905E-page 326  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at Users of Microchip products can receive assistance www.microchip.com. This web site is used as a means through several channels: to make files and information easily available to • Distributor or Representative customers. Accessible by using your favorite Internet • Local Sales Office browser, the web site contains the following • Field Application Engineer (FAE) information: • Technical Support • Product Support – Data sheets and errata, • Development Systems Information Line application notes and sample programs, design resources, user’s guides and hardware support Customers should contact their distributor, documents, latest software releases and archived representative or field application engineer (FAE) for software support. Local sales offices are also available to help • General Technical Support – Frequently Asked customers. A listing of sales offices and locations is Questions (FAQ), technical support requests, included in the back of this document. online discussion groups, Microchip consultant Technical support is available through the web site program member listing at: http://support.microchip.com • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under “Support”, click on “Customer Change Notification” and follow the registration instructions.  2010 Microchip Technology Inc. DS39905E-page 327

PIC24FJ256GA110 FAMILY READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480)792-4150. Please list the following information, and use this outline to provide us with your comments about this document. TO: Technical Publications Manager Total Pages Sent ________ RE: Reader Response From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: PIC24FJ256GA110 family Literature Number: DS39905E Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS39905E-page 328  2010 Microchip Technology Inc.

PIC24FJ256GA110 FAMILY PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PIC 24 FJ 256 GA1 10 T - I / PT - XXX Examples: a) PIC24FJ128GA106-I/PT: Microchip Trademark General purpose PIC24F, 128-Kbyte program memory, 64-pin, Industrial temp.,TQFP package. Architecture b) PIC24FJ256GA110-I/PT: Flash Memory Family General purpose PIC24F, 256-Kbyte program memory, 100-pin, Industrial temp.,TQFP package. Program Memory Size (KB) Product Group Pin Count Tape and Reel Flag (if applicable) Temperature Range Package Pattern Architecture 24 = 16-bit modified Harvard without DSP Flash Memory Family FJ = Flash program memory Product Group GA1= General purpose microcontrollers Pin Count 06 = 64-pin 08 = 80-pin 10 = 100-pin Temperature Range I = -40C to +85C (Industrial) Package PF = 100-lead (14x14x1mm) TQFP (Thin Quad Flatpack) PT = 64-lead, 80-lead, 100-lead (12x12x1 mm) TQFP (Thin Quad Flatpack) MR = 64-lead (9x9x0.9 mm) QFN (Quad Flatpack No Leads) Pattern Three-digit QTP, SQTP, Code or Special Requirements (blank otherwise) ES = Engineering Sample  2010 Microchip Technology Inc. DS39905E-page 329

Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office Asia Pacific Office India - Bangalore Austria - Wels 2355 West Chandler Blvd. Suites 3707-14, 37th Floor Tel: 91-80-3090-4444 Tel: 43-7242-2244-39 Chandler, AZ 85224-6199 Tower 6, The Gateway Fax: 91-80-3090-4123 Fax: 43-7242-2244-393 Tel: 480-792-7200 Harbour City, Kowloon India - New Delhi Denmark - Copenhagen Fax: 480-792-7277 Hong Kong Tel: 91-11-4160-8631 Tel: 45-4450-2828 Technical Support: Tel: 852-2401-1200 Fax: 91-11-4160-8632 Fax: 45-4485-2829 http://support.microchip.com Web Address: Fax: 852-2401-3431 India - Pune France - Paris www.microchip.com Australia - Sydney Tel: 91-20-2566-1512 Tel: 33-1-69-53-63-20 Tel: 61-2-9868-6733 Fax: 91-20-2566-1513 Fax: 33-1-69-30-90-79 ADtullaunthta, GA Fax: 61-2-9868-6755 Japan - Yokohama Germany - Munich Tel: 678-957-9614 China - Beijing Tel: 81-45-471- 6166 Tel: 49-89-627-144-0 Tel: 86-10-8528-2100 Fax: 49-89-627-144-44 Fax: 678-957-1455 Fax: 81-45-471-6122 Fax: 86-10-8528-2104 Italy - Milan Boston Korea - Daegu Westborough, MA China - Chengdu Tel: 82-53-744-4301 Tel: 39-0331-742611 Tel: 774-760-0087 Tel: 86-28-8665-5511 Fax: 82-53-744-4302 Fax: 39-0331-466781 Fax: 774-760-0088 Fax: 86-28-8665-7889 Korea - Seoul Netherlands - Drunen Chicago China - Chongqing Tel: 82-2-554-7200 Tel: 31-416-690399 Itasca, IL Tel: 86-23-8980-9588 Fax: 82-2-558-5932 or Fax: 31-416-690340 Tel: 630-285-0071 Fax: 86-23-8980-9500 82-2-558-5934 Spain - Madrid Fax: 630-285-0075 China - Hong Kong SAR Malaysia - Kuala Lumpur Tel: 34-91-708-08-90 Cleveland Tel: 852-2401-1200 Tel: 60-3-6201-9857 Fax: 34-91-708-08-91 Independence, OH Fax: 852-2401-3431 Fax: 60-3-6201-9859 UK - Wokingham Tel: 216-447-0464 China - Nanjing Malaysia - Penang Tel: 44-118-921-5869 Fax: 216-447-0643 Tel: 86-25-8473-2460 Tel: 60-4-227-8870 Fax: 44-118-921-5820 Dallas Fax: 86-25-8473-2470 Fax: 60-4-227-4068 Addison, TX China - Qingdao Philippines - Manila Tel: 972-818-7423 Tel: 86-532-8502-7355 Tel: 63-2-634-9065 Fax: 972-818-2924 Fax: 86-532-8502-7205 Fax: 63-2-634-9069 Detroit China - Shanghai Singapore Farmington Hills, MI Tel: 86-21-5407-5533 Tel: 65-6334-8870 Tel: 248-538-2250 Fax: 86-21-5407-5066 Fax: 65-6334-8850 Fax: 248-538-2260 China - Shenyang Taiwan - Hsin Chu Kokomo Tel: 86-24-2334-2829 Tel: 886-3-6578-300 Kokomo, IN Fax: 86-24-2334-2393 Fax: 886-3-6578-370 Tel: 765-864-8360 Fax: 765-864-8387 China - Shenzhen Taiwan - Kaohsiung Tel: 86-755-8203-2660 Tel: 886-7-213-7830 Los Angeles Fax: 86-755-8203-1760 Fax: 886-7-330-9305 Mission Viejo, CA Tel: 949-462-9523 China - Wuhan Taiwan - Taipei Tel: 86-27-5980-5300 Tel: 886-2-2500-6610 Fax: 949-462-9608 Fax: 86-27-5980-5118 Fax: 886-2-2508-0102 Santa Clara China - Xian Thailand - Bangkok Santa Clara, CA Tel: 408-961-6444 Tel: 86-29-8833-7252 Tel: 66-2-694-1351 Fax: 408-961-6445 Fax: 86-29-8833-7256 Fax: 66-2-694-1350 China - Xiamen Toronto Mississauga, Ontario, Tel: 86-592-2388138 Canada Fax: 86-592-2388130 Tel: 905-673-0699 China - Zhuhai Fax: 905-673-6509 Tel: 86-756-3210040 Fax: 86-756-3210049 08/04/10 DS39905E-page 330  2010 Microchip Technology Inc.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M icrochip: PIC24FJ128GA106-I/PT PIC24FJ128GA106T-I/PT PIC24FJ128GA108-I/PT PIC24FJ128GA108T-I/PT PIC24FJ128GA110-I/PF PIC24FJ128GA110-I/PT PIC24FJ128GA110T-I/PF PIC24FJ128GA110T-I/PT PIC24FJ192GA106-I/PT PIC24FJ192GA106T-I/PT PIC24FJ192GA108-I/PT PIC24FJ192GA108T-I/PT PIC24FJ192GA110-I/PF PIC24FJ192GA110-I/PT PIC24FJ192GA110T-I/PF PIC24FJ192GA110T-I/PT PIC24FJ256GA106-I/PT PIC24FJ256GA106T-I/PT PIC24FJ256GA108-I/PT PIC24FJ256GA108T-I/PT PIC24FJ256GA110-I/PF PIC24FJ256GA110-I/PT PIC24FJ256GA110T-I/PF PIC24FJ256GA110T-I/PT PIC24FJ256GA106-E/MR PIC24FJ192GA106-I/MR PIC24FJ256GA106-I/MR PIC24FJ192GA106-E/MR PIC24FJ128GA106-I/MR PIC24FJ128GA106-E/PT PIC24FJ128GA108-E/PT PIC24FJ128GA110-E/PT PIC24FJ192GA106-E/PT PIC24FJ192GA108-E/PT PIC24FJ192GA110-E/PT PIC24FJ256GA106-E/PT PIC24FJ256GA108-E/PT PIC24FJ256GA110-E/PT PIC24FJ64GA106-E/MR PIC24FJ64GA106-E/PT PIC24FJ64GA106-I/MR PIC24FJ64GA106-I/PT PIC24FJ64GA106T-I/PT PIC24FJ64GA108-E/PT PIC24FJ64GA108- I/PT PIC24FJ64GA108T-I/PT PIC24FJ64GA110-E/PT PIC24FJ64GA110-I/PF PIC24FJ64GA110-I/PT PIC24FJ64GA110T-I/PF PIC24FJ64GA110T-I/PT PIC24FJ128GA106-E/MR PIC24FJ64GA106T-I/MR