LD29080 800 mA fixed and adjustable output very low drop voltage regulator Datasheet - production data • Fixed and adjustable output voltage (± 1 % at 25 °C) • Internal current and thermal limit • Logic controlled electronic shutdown Description PPAK DPAK The LD29080 is a medium current, high accuracy, low-dropout voltage regulators series. These regulators feature 400 mV dropout voltage and very low ground current. Designed for medium SOT223 current loads, these devices also find applications in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes. Features Typical application are in power supply switching • Very low dropout voltage (typ. 0.4 at 800 mA) post regulation, series power supply for monitors, series power supply for VCRs and TVs, computer • Guaranteed output current up to 800 mA systems and battery powered systems. Table 1. Device summary Order codes Output voltages DPAK (tape and reel) PPAK (tape and reel) SOT223 LD29080DT15R LD29080PT15R 1.5 V LD29080DT18R LD29080PT18R 1.8 V LD29080DT25R LD29080PT25R 2.5 V LD29080DT33R LD29080PT33R LD29080S33R 3.3 V LD29080DT50R LD29080PT50R 5.0 V LD29080DT90R LD29080PT90R 9.0 V LD29080PTR ADJ November 2013 DocID10918 Rev 8 1/26 This is information on a product in full production. www.st.com 26

Contents LD29080 Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2/26 DocID10918 Rev 8

LD29080 Diagram 1 Diagram Figure 1. Schematic diagram for adjustable version Figure 2. Schematic diagram for fixed version * Only for version with inhibit function. DocID10918 Rev 8 3/26

Pin configuration LD29080 2 Pin configuration Figure 3. Pin connections (top view) 5 3 4 GND GND 3 GND 2 2 1 1 1 2 3 CS17230 CS17240 AM09358v1 PPAK DPAK SOT223 Table 2. Pin description Symbol PPAK DPAK SOT223 V 2 1 1 I GND 3 2 2 V 4 3 3 O ADJ/N.C. (1) 5 INHIBIT (2) 1 1. Not connected for fixed version. 2. Not internally pulled up; in order to assure the operating condition (device in ON mode), it must be connected to a positive voltage higher than 2 V. Figure 4. Application circuit V = V (1 + R /R ) O REF 1 2 * Only for version with inhibit function. 4/26 DocID10918 Rev 8

LD29080 Maximum ratings 3 Maximum ratings Table 3. Absolute maximum ratings Symbol Parameter Value Unit V DC input voltage 30 (1) V I V Inhibit input voltage 14 V INH I Output current Internally limited mA O P Power dissipation Internally limited mW D T Storage temperature range - 55 to 150 °C STG T Operating temperature range - 40 to 125 °C OP 1. Above 14 V the device is automatically in shut-down. Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Table 4. Thermal data Symbol Parameter DPAK PPAK SOT223 Unit R Thermal resistance junction-case 8 8 25 °C/W thJC R Thermal resistance junction-ambient 100 100 110 °C/W thJA DocID10918 Rev 8 5/26

Electrical characteristics LD29080 4 Electrical characteristics I = 10 mA, (Note4) T = 25 °C, V = 3.5 V, V = 2V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified. Table 5. Electrical characteristics of LD29080#15 Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10 mA to 800 mA 2.5 13 V I O I = 10 mA to 800 mA, V = 3 to 7 V 1.485 1.5 1.515 V Output voltage O I V O TJ = -40 to 125 °C 1.463 1.537 ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 3 to 13 V 0.06 0.5 % O I f = 120 Hz, V = 3.8 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 65 75 dB (Note1) I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 60 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. 6/26 DocID10918 Rev 8

LD29080 Electrical characteristics I = 10 mA, (Note4) T = 25 °C, V = 3.5 V, V = 2 V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified. Table 6. Electrical characteristics of LD29080#18 Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10 mA to 800 mA 2.5 13 V I O I = 10 mA to 800 mA, V = 3 to 7.3 V 1.782 1.8 1.818 V Output voltage O I V O TJ = -40 to 125 °C 1.755 1.845 ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 3 to 13 V 0.06 0.5 % O I f = 120 Hz, V = 3.8 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 62 72 dB (Note1) I = 150 mA, T = -40 to 125 °C (Note2) 0.1 O J V Dropout voltage I = 400 mA, T = -40 to 125 °C (Note2) 0.2 V DROP O J I = 800 mA, T = -40 to 125 °C (Note2) 0.4 0.7 O J I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13 V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 72 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 8 7/26

Electrical characteristics LD29080 I = 10 mA, (Note4) T = 25 °C, V = 4.5 V, V = 2 V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified. Table 7. Electrical characteristics of LD29080#25 Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10 mA to 800 mA 13 V I O I = 10 mA to 800 mA, V = 3.5 to 8 V 2.475 2.5 2.525 V Output voltage O I V O TJ = -40 to 125 °C 2.438 2.562 ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 3.5 to 13 V 0.06 0.5 % O I f = 120 Hz, V = 4.5 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 55 70 dB (Note1) I = 150 mA, T = -40 to 125 °C (Note2) 0.1 O J V Dropout voltage I = 400 mA, T = -40 to 125 °C (Note2) 0.2 V DROP O J I = 800 mA, T = -40 to 125 °C (Note2) 0.4 0.7 O J I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13 V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 100 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. 8/26 DocID10918 Rev 8

LD29080 Electrical characteristics I = 10 mA, (Note4) T = 25 °C, V = 5.3 V, V = 2 V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified. Table 8. Electrical characteristics of LD29080#33 Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10mA to 800mA 13 V I O I = 10 mA to 800 mA, V = 4.3 to 8.8 V 3.267 3.3 3.333 V Output voltage O I V O TJ = -40 to 125 °C 3.218 3.382 ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 4.3 to 13 V 0.06 0.5 % O I f = 120 Hz, V = 5.3 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 52 67 dB (Note1) I = 150 mA, T = -40 to 125 °C (Note2) 0.1 O J V Dropout voltage I = 400 mA, T = -40 to 125 °C (Note2) 0.2 V DROP O J I = 800 mA, T = -40 to 125 °C (Note2) 0.4 0.7 O J I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13 V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 132 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 8 9/26

Electrical characteristics LD29080 I = 10 mA, (Note4) T = 25 °C, V = 7 V, V = 2 V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified. Table 9. Electrical characteristics of LD29080#50 Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10 mA to 800 mA 13 V I O I = 10 mA to 800 mA, V = 6 to 10.5 V 4.95 5 5.05 V Output voltage O I V O TJ = -40 to 125 °C 4.875 5.125 ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 6 to 13 V 0.06 0.5 % O I f = 120 Hz, V = 7 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 49 64 dB (Note1) I = 150 mA, T = -40 to 125 °C (Note2) 0.1 O J V Dropout voltage I = 400 mA, T = -40 to 125 °C (Note2) 0.2 V DROP O J I = 800 mA, T = -40 to 125 °C (Note2) 0.4 0.7 O J I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13 V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 180 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. 10/26 DocID10918 Rev 8

LD29080 Electrical characteristics I = 10 mA, (Note4) T = 25 °C, V = 10 V, V = 2 V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified) Table 10. Electrical characteristics of LD29080#80 Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10 mA to 800 mA 13 V I O I = 10 mA to 800 mA, V = 9 to 13 V 7.92 8 8.08 V Output voltage O I V O TJ = -40 to 125 °C 7.80 8.20 ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 9 to 13 V 0.06 0.5 % O I f = 120 Hz, V = 10 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 45 59 dB (Note1) I = 150 mA, T = -40 to 125 °C (Note2) 0.1 O J V Dropout voltage I = 400 mA, T = -40 to 125 °C (Note2) 0.2 V DROP O J I = 800 mA, T = -40 to 125 °C (Note2) 0.4 0.7 O J I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13 V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 320 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 8 11/26

Electrical characteristics LD29080 I = 10 mA, (Note4) T = 25 °C, V = 11 V, V = 2 V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified. Table 11. Electrical characteristics of LD29080#90 Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10 mA to 800 mA 13 V I O I = 10 mA to 800 mA, V = 9 to 13 V 8.91 9 9.09 V Output voltage O I V O TJ = -40 to 125 °C 8.775 9.225 ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 10 to 13 V 0.06 0.5 % O I f = 120 Hz, V = 11 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 43 57 dB (Note1) I = 150 mA, T = -40 to 125 °C (Note2) 0.1 O J V Dropout voltage I = 400 mA, T = -40 to 125 °C (Note2) 0.2 V DROP O J I = 800 mA, T = -40 to 125 °C (Note2) 0.4 0.7 O J I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13 V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 330 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. 12/26 DocID10918 Rev 8

LD29080 Electrical characteristics I = 10 mA, (Note4) T = 25 °C, V = 10 V, V = 2 V, C = 330 nF, C = 10 µF, unless O J I INH I O otherwise specified. Table 12. Electrical characteristics of LD29080#ADJ Symbol Parameter Test conditions Min. Typ. Max. Unit V Operating input voltage I = 10 mA to 800 mA 2.5 13 V I O ΔV Load regulation I = 10 mA to 800 mA 0.2 1.0 % O O ΔV Line regulation V = 2.5 to 13 V, I = 10 mA 0.06 0.5 % O I O I = 10 mA to 800 mA, V = 2.5 to 6.73 V 1.2177 1.23 1.2423 V Reference voltage O I V REF TJ = -40 to 125 °C (Note3) 1.1993 1.2607 f = 120 Hz, V = 3.23 ± 1 V, I = 400 mA SVR Supply voltage rejection I O 45 75 dB (Note1) I = 10 mA, T = -40 to 125 °C 2 5 O J I = 400 mA, T = -40 to 125 °C 8 20 mA O J I Quiescent current q I = 800 mA, T = -40 to 125 °C 14 35 O J V = 13 V, V = GND, T = -40 to 125 °C 130 180 µA I INH J I Adjust pin current T = -40 to 125 °C 1 µA ADJ J I Short circuit current R = 0 1.2 A sc L V Control input logic low OFF MODE, T = -40 to 125 °C 0.8 V IL J V Control input logic high ON MODE, T = -40 to 125 °C 2 V IH J I Control input current V = 13 V, T = -40 to 125 °C 5 10 µA INH INH J B = 10 Hz to 100 kHz, I = 100 mA eN Output noise voltage P O 50 µV (Note1) RMS Note: 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with V + 1 V applied to V. O I 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to V . O 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 8 13/26

Typical characteristics LD29080 5 Typical characteristics Figure 5. Output voltage vs. temperature Figure 6. Reference voltage vs. temperature Figure 7. Dropout voltage vs. temperature Figure 8. Dropout voltage vs. output current Figure 9. Quiescent current vs. output current Figure 10. Quiescent current vs. temperature (I = 10 mA) o 14/26 DocID10918 Rev 8

LD29080 Typical characteristics Figure 11. Quiescent current vs. supply voltage Figure 12. Quiescent current vs. temperature (I = 800 mA) o Figure 13. Short circuit current vs. temperature Figure 14. Adjust pin current vs. temperature Figure 15. Supply voltage rejection vs. Figure 16. Output voltage vs. input voltage temperature DocID10918 Rev 8 15/26

Typical characteristics LD29080 Figure 17. Stability vs. C Figure 18. Line transient O V = 3.5 to 13 V, I = 10 mA, V = 1.5 V I O O Figure 19. Load transient V = 3.5 V, I = 10 mA to 0.8 A, V = 1.5 V I O O 16/26 DocID10918 Rev 8

LD29080 Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 13. PPAK mechanical data mm Dim. Min. Typ. Max. A 2.2 2.4 A1 0.9 1.1 A2 0.03 0.23 B 0.4 0.6 B2 5.2 5.4 C 0.45 0.6 C2 0.48 0.6 D 6 6.2 D1 5.1 E 6.4 6.6 E1 4.7 e 1.27 G 4.9 5.25 G1 2.38 2.7 H 9.35 10.1 L2 0.8 1 L4 0.6 1 L5 1 L6 2.8 R 0.20 V2 0° 8° DocID10918 Rev 8 17/26

Package mechanical data LD29080 Figure 20. PPAK drawing 0078180_F 18/26 DocID10918 Rev 8

LD29080 Package mechanical data Table 14. DPAK mechanical data mm Dim. Min. Typ. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 5.10 E 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1.00 1.50 (L1) 2.80 L2 0.80 L4 0.60 1.00 R 0.20 V2 0° 8° DocID10918 Rev 8 19/26

Package mechanical data LD29080 Figure 21. DPAK drawing 0068772_K 20/26 DocID10918 Rev 8

LD29080 Package mechanical data Figure 22. DPAK footprint (a) Footprint_REV_K a. All dimensions are in millimeters DocID10918 Rev 8 21/26

Package mechanical data LD29080 Table 15. SOT-223 mechanical data mm Dim. Min. Typ. Max. A 1.80 A1 0.02 0.1 B 0.60 0.70 0.85 B1 2.90 3.00 3.15 c 0.24 0.26 0.35 D 6.30 6.50 6.70 e 2.30 e1 4.60 E 3.30 3.50 3.70 H 6.70 7.00 7.30 V 10° Figure 23. SOT-223 mechanical data drawing 0046067_M 22/26 DocID10918 Rev 8

LD29080 Packaging mechanical data 7 Packaging mechanical data Table 16. PPAK and DPAK tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. Min. Max. A0 6.8 7 A 330 B0 10.4 10.6 B 1.5 B1 12.1 C 12.8 13.2 D 1.5 1.6 D 20.2 D1 1.5 G 16.4 18.4 E 1.65 1.85 N 50 F 7.4 7.6 T 22.4 K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID10918 Rev 8 23/26

Packaging mechanical data LD29080 Figure 24. Tape for PPAK and DPAK 10 pitches cumulative tolerance on tape +/- 0.2 mm Top cover P0 D P2 T tape E F K0 W B1 B0 For machine ref. only A0 P1 D1 including draft and radii concentric around B0 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 25. Reel for PPAK and DPAK T REEL DIMENSIONS 40mm min. Access hole At slot location B D C N A Full radius Tape slot G measured at hub in core for tape start 25 mm min. width AM08851v2 24/26 DocID10918 Rev 8

LD29080 Revision history 8 Revision history Table 17. Document revision history Date Revision Changes 15-Oct-2004 1 First release. 20-Oct-2005 2 Order codes updated. 14-May-2007 3 Order codes updated. 26-Jan-2009 4 Modified: eN value in Table9 on page10. 22-Feb-2011 5 Added: new order code Table1 on page1 and mechanical data. 12-Jan-2012 6 Modified: R and R value for SOT223 Table4 on page5. thJA thJC 08-May-2012 7 Modified: pin connections for PPAK, DPAK and SOT223 Figure3 on page4. Part number LD29080xx changed to LD29080. Updated the Description in cover page, Table1: Device summary. Updated Section5: Typical characteristics and Section6: Package mechanical 22-Nov-2013 8 data. Added Section7: Packaging mechanical data. Minor text changes. DocID10918 Rev 8 25/26

LD29080 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 26/26 DocID10918 Rev 8

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: S TMicroelectronics: LD29080DT90R LD29080PT15R LD29080PT33R LD29080DT15R LD29080DT50R LD29080PT25R LD29080PT50R LD29080PT90R LD29080DT25R LD29080DT33R LD29080PTR LD29080DT18R LD29080PT18R LD29080S33R