High voltage resistance chip resistors KTR series Datasheet Features ● 1)Twice the rated voltage of conventional products.. 2)Perfect for use in high voltage circuit. (Camera Flash circuit, etc) 3)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 4)Corresponds to AEC-Q200. (KTR18) Products list ● Size Rated Limiting Temperature Resistance Operating Automotive power plement Resistance range temperature Part No. coefficient tolerance grade (70℃) voltage range available (mm) (inch) (W) (V) (ppm / ℃) (%) (Ω) (℃) ±200 F ( ±1% ) 1≦R≦10 (E24/96 series) KTR03 1608 0603 0.10 350 ±100 F ( ±1% ) 10≦R≦10M (E24/96 series) -55 ～ +155 Yes ±200 J ( ±5% ) 1≦R≦10M (E24 series) ±100 F ( ±1% ) 1≦R≦10M (E24/96 series) KTR10 2012 0805 0.125 400 -55 ～ +155 Yes ±200 J ( ±5% ) 1≦R≦10M (E24 series) ±100 F ( ±1% ) 1≦R≦10M (E24/96 series) KTR18 3216 1206 0.25 500 -55 ～ +155 Yes ±200 J ( ±5% ) 1≦R≦10M (E24 series) ±100 F ( ±1% ) 1≦R≦10M (E24/96 series) KTR25 3225 1210 0.33 600 -55 ～ +155 Yes ±200 J ( ±5% ) 1≦R≦10M (E24 series) *E24 : Standard products, E96 : Custom products. Part number description ●● K T R 1 0 E Z P J 1 0 0 Resistance Part No. Size (mm [inch]) Packaging specifications code Nominal resistance tolerance 03 (1608 [0603]) Packaging Quantity Resistance code, 3 or 4 digits. KTR Part No. Code F( ±1% ) 10 (2012 [0805]) specifications / Reel 000 denotes jumper type. (High voltage J ( ±5% ) 18 (3216 [1206]) Paper tape Resistance Resistance resistance KTR03 EZP 5,000 25 (3225 [1210]) (4mm Pitch) tolerance code chip resistors) Paper tape F ： 4 digits KTR10 EZP 5,000 (4mm Pitch) J ： 3 digits Paper tape EX.) KTR18 EZP 5,000 (4mm Pitch) 1Ω = 1R00 (±1%) Embossed tape 1R0 (±5%) KTR25 JZP 4,000 (4mm Pitch) 10Ω = 10R0 (±1%) 100 (±5%) 1MΩ = 1004 (±1%) 105 (±5%) www.rohm.com 1/4 c 2016 ROHM Co., Ltd. All rights reserved. 2015.07 - Rev.E

KTR series 　 　 　 　 　 　 　 Datasheet Chip resistor dimensions and markings ● ■KTR03 ■KTR10/18/25 <Marking method> There are three or four digits used for the calculation number according to IEC code and "R" is used for the decimal point. (Unit:mm) Marking Part No. (mm) (inch) L W t a b existence 　 　 　 KTR03 1608 0603 1.60±0.10 0.80±0.10 0.45±0.10 0.30±0.20 0.30±0.20 No* 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 KTR10 2012 0805 2.00±0.10 1.25±0.10 0.55±0.10 0.30±0.20 0.40±0.20 Yes 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 KTR18 3216 1206 3.20±0.15 1.60±0.15 0.55±0.10 0.30±0.25 0.50±0.25 Yes 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 　　 　 KTR25 3225 1210 3.20±0.15 2.50±0.15 0.55±0.10 0.30±0.25 0.50±0.25 Yes 　　 　 　　 　 　　 　 　　 　 　　 　 *Only with spuare mark Land pattern example ● (Unit:mm) Dimensions A B C D Part No. KTR03 1.0 2.0 0.8 0.5 KTR10 1.2 2.6 1.15 0.7 KTR18 2.2 4.0 1.5 0.9 KTR25 2.2 4.0 2.3 0.9 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 www.rohm.com 2/4 c 2016 ROHM Co., Ltd. All rights reserved. 2015.07 - Rev.E

KTR series 　 　 　 　 　 　 　 Datasheet Derating curve ● When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below. ■KTR03/10/18/25 Characteristics ● Guaranteed > Test items Test conditions Resistor type Resistance See P.1 20℃ Variation of resistance See P.1 Measurement：+25/-55, +25/+125℃ with temperature Test voltage is the smaller one of ① or ② Overload ±(2.0％＋0.1Ω) ①Rated voltage(current)×2.5， 2s ②Maximum overload voltage ※ A new uniform coating of minimum Rosin-ethanol solution(25% weight) of 95% of the surface being Solderability 　 　 Soldering condition：245±5℃ immersed and no soldering Duration of immersion：2.0±0.5s damage. Resistance to ±(1.0％＋0.05Ω) Soldering condition：260±5℃ soldering heat No remarkable abnormality on the appearance. Duration of immersion：10±1s Rapid change of ±(1.0％＋0.05Ω) Test temp：-55℃～+125℃ 5cycle temperature 40℃，93％(Relative humidity) Damp heat, steady state ±(3.0％＋0.1Ω) Test time：1,000h Rated voltage(current),70℃ Endurance at 70℃ ±(3.0％＋0.1Ω) 1.5h:ON－0.5h:OFF Test time：1,000h 155℃ Endurance ±(3.0％＋0.1Ω) Test time：1,000h 23±5℃ Immersion cleaning, Resistance to solvent ±(1.0％＋0.05Ω) Solvent: 2-propanol Bend strength of ±(1.0％＋0.05Ω) - the end face plating Without mechanical damage such as breaks. 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Compliance Standard(s) : IEC60115-8 ※Maximum overload voltage (Test voltage) JISC 5201-8 KTR03 KTR10 KTR18 KTR25 500V 800V 1000V 1200V 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 www.rohm.com 　 　　　　　　　　　 3/4 c 2016 ROHM Co., Ltd. All rights reserved. 2015.07 - Rev.E

KTR series 　 　 　 　 　 　 　 Datasheet Tape dimensions ● ■Paper tape (Unit : mm) Part No. W F E A0 B0 　 　 　 　 KTR03 8.0±0.3 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 　 　 　 　 　 　 　 　 　 　 　 　 +0.2 　 　 +0.2 KTR10 8.0±0.3 3.5±0.05 1.75±0.1 1.65 2.4 　 　 　 　 　 　 　 　 -0.1 　 　 -0.1 　 　 　 　 　 　 　 　 +0.1 　 　 +0.15 KTR18 8.0±0.3 3.5±0.05 1.75±0.1 1.95 3.5 　 　 　 　 　 　 　 　 -0.05 　 　 -0.05 Part No. D0 P0 P1 P2 T2 +0.1 　 　 　 　 KTR03 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 　 　 　 　 　 　 +0.1 　 　 　 　 　 　 　 　 KTR10 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 　 　 0 　 　 　 　 　 　 　 　 +0.1 　 　 　 　 KTR18 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 　 　 0 　 　 　 　 　 　 　 　 ■Embossed tape (Unit : mm) Part No. W F E A0 B0 　 　 　 　 8.0±0.3 3.5±0.05 1.75±0.1 3.0±0.1 3.5±0.1 　 　 　 　 KTR25 D0 P0 P1 P2 T2 +0.1 　 　 　 　 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 　 　 0 　 　 　 　 　 　 　 　 Reel dimensions ● (Unit : mm) Part No. A B C D KTR03 　 　 0 +1 +1.0 KTR10 Φ180 Φ60 9 Φ13±0.2 KTR18 -1.5 0 0 KTR25 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 www.rohm.com 　 　　　　　　　　　 4/4 c 2016 ROHM Co., Ltd. All rights reserved. 2015.07 - Rev.E

Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment(Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Notice-PAA-E Rev.001 c 2016 ROHM Co., Ltd. All rights reserved.

Datasheet 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreigntrade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Notice-PAA-E Rev.001 c 2016 ROHM Co., Ltd. All rights reserved.

Datasheet 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising form the use of any ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document not is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sales representative. 3. The information contained in this document is provided on an “as in” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting form inaccuracy or errors of or concerning such information. 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Notice – WE Rev.001 c 2016 ROHM Co., Ltd. All rights reserved.

Datasheet KTR25JZPF - Web Page Distribution Inventory Part Number KTR25JZPF Package Unit Quantity 4000 Minimum Package Quantity 4000 Packing Type Taping Constitution Materials List inquiry RoHS Yes

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: R OHM Semiconductor: KTR25JZPF1604 KTR25JZPF3301 KTR25JZPF3900 KTR25JZPF8201 KTR25JZPF1200 KTR25JZPF1100 KTR25JZPF4R30 KTR25JZPF4704 KTR25JZPF1304 KTR25JZPF5603 KTR25JZPF16R0 KTR25JZPF12R0 KTR25JZPF2700 KTR25JZPF5101 KTR25JZPF68R0 KTR25JZPF1001 KTR25JZPF3901 KTR25JZPF5604 KTR25JZPF3601 KTR25JZPF3902 KTR25JZPF3302 KTR25JZPF1804 KTR25JZPF51R0 KTR25JZPF3004 KTR25JZPF1600 KTR25JZPF2004 KTR25JZPF3003 KTR25JZPF6201 KTR25JZPF5100 KTR25JZPF8203 KTR25JZPF1601 KTR25JZPF75R0 KTR25JZPF3R30 KTR25JZPF9R10 KTR25JZPF1800 KTR25JZPF1301 KTR25JZPF3604 KTR25JZPF1102 KTR25JZPF3R60 KTR25JZPF6804 KTR25JZPF6203 KTR25JZPF2202 KTR25JZPF1103 KTR25JZPF1101 KTR25JZPF1801 KTR25JZPF56R0 KTR25JZPF5600 KTR25JZPF15R0 KTR25JZPF3R00 KTR25JZPF4300 KTR25JZPF7500 KTR25JZPF1501 KTR25JZPF9102 KTR25JZPF4302 KTR25JZPF1503 KTR25JZPF1R20 KTR25JZPF36R0 KTR25JZPF1002 KTR25JZPF2001 KTR25JZPF2703 KTR25JZPF4303 KTR25JZPF7504 KTR25JZPF2R40 KTR25JZPF1R50 KTR25JZPF3602 KTR25JZPF2R70 KTR25JZPF3000 KTR25JZPF7R50 KTR25JZPF1502 KTR25JZPF1104 KTR25JZPF1R10 KTR25JZPF1204 KTR25JZPF3303 KTR25JZPF2201 KTR25JZPF4301 KTR25JZPF3600 KTR25JZPF3304 KTR25JZPF1302 KTR25JZPF2003 KTR25JZPF3904 KTR25JZPF6202 KTR25JZPF1803 KTR25JZPF9104 KTR25JZPF1201 KTR25JZPF2402 KTR25JZPF30R0 KTR25JZPF5103 KTR25JZPF2401 KTR25JZPF4304 KTR25JZPF6803 KTR25JZPF1R00 KTR25JZPF8202 KTR25JZPF2000 KTR25JZPF2204 KTR25JZPF1802 KTR25JZPF6204 KTR25JZPF11R0 KTR25JZPF5602 KTR25JZPF5601 KTR25JZPF3603