Spec. No. JENF243H-0006H-01 R eference Only P 1/ 7 Block Type EMIFIL® BNX005-01 Reference Specification 1. Scope This reference specification applies to Block Type EMIFIL® . 2. Rating 2.1 Customer Part Number 2.2 Murata Part Number BNX005-01 2.3 Rated Voltage 50 V(DC) 2.4 Test Voltage 125 V(DC) 2.5 Rated Current 15 A(DC) 2.6 Insulation Resistance 100 M min. 2.7 Voltage Drop 30 mV max. 1 MHz to 1 GHz : 40dB min. 2.8 Insertion Loss Line impedance = 50  2.9 Equivalent Circuits See the item 4 2.10 Operating Temperature - 30 °C ~ + 85 °C 2.11 Storage Temperature - 40 °C ~ + 85 °C 3. Standard Testing Condition <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temp. 15 °C to 35 °C Temperature : 20 °C ± 2 °C Humidity : Ordinary Humidity 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH) Atmospheric pressure : 86 kPa to 106 kPa 4. Style and Dimensions 12.0±0.5 11.0±0.5 ax. m 5 x. 13. ma 5 8. 1 1.0 1.0 5 1.0 1.0 3.5± 0.8±0.1 5.0±0. ±0.1 0.6 ±0.2 ±0.2 ±0.2 2.5 2.5 2.5 ±0.2 ±0.2 2.5 2.5 7.5±0.2 Note) Although some part of the product surface seems to be white in some cases, do not care because it is the result of waxing process for humidity resistance improvement. This wax does not make bad affection to mechanical or electrical performance, reliability of the product. TERMINAL LAYOUT (BOTTOM FIGURE)  DIMENSIONS OF INSTALLATION HOLES (front view) 1.2 (4)CG CB (2) (PSG) (B) 0.1 CG CG 5± 2. 1 (CG) (CG) 0. (3)PSG B(1) 5± (CG) 2. (CB) 2.5±0.1 5.0±0.1 7.5±0.1 (inmm) MURATA MFG CO.,LTD.

Spec. No. JENF243H-0006H-01 R eference Only P 2/ 7  EQUIVALENT CIRCUIT (1) B L1 L3 C2 CB(2) L2 C1  Unit Mass (Typical value) (3)PSG CG(4) 3.3g (1)~(4):Terminal 5. Marking Filter shall be marked as follows. Muratamark BNX005-01 PartNumber ManufacturingDate (Ex.)59 5･･･ 1995(Lastdigitoftheyear) 9･･･ September Jan.toSept.1~9 Oct.:O,Nov.:N,Dec,:D 6. Electrical Performance No. Item Specification Test Method 6.1 Insulation Meet item 2.6. Measured at DC rated voltage between terminal Resistance (1)(2) and (3)(4). Time : 1 minute Suitable resistor : 1M. 6.2 Dielectric Filter shall be no failure. Test voltage shall be applied between terminal Strength (1)(2) and terminal (3)(4). Time : 1 to 5 seconds. Charging current : 50 mA max. 6.3 Voltage Meet item 2.7. Rated Current : 15 A Drop A (1) (2) V Specimen (3) (4) 6.4 Insertion Meet item 2.8. Loss 50 50 10dB Balun (1) (2) 10dB Attenuator Attenuator Specimen 50 (3) (4) E ～ 50 SG MethodofmeasurementbasedonMIL-STD-220 Insertion Loss = 20log (E / E ) 0 1 Ｅ : Level without FILTER (short) 0 Ｅ : Level with FILTER １ 7. Mechanical Performance No. Item Specification Test Method 7.1 Appearance and Meet item 4. Visual Inspection and measured with Slide Dimensions Calipers. 7.2 Marking Marking is able to be read easily. It is inspected Visually. MURATA MFG CO.,LTD.

Spec. No. JENF243H-0006H-01 R eference Only P 3/ 7 No. Item Specification Test Method 7.3 Vibration Meet Table 1. It shall be soldered on the substrate. Table 1 Range of Vibration Frequency : Appearance No damaged 10 to 2000 to 10Hz for 20 minutes Insulation Testing Time : A period of 2 hours in each of 3 30 M min. Resistance Mutually perpendicular directions Dielectric (Total 6 hours) No failure Strength Double Amplitude : 1.5mm or acceleration 196m / Insertion Meet item 2.8 s2 Loss Then measured after exposure in the room condition for 4 to 24 hours. 7.4 Solderability Then the lead is covered with a Flux : Ethanol solution of rosin, 25(wt)% continuous new solder coating at Pre-heat : 150 ± 10 °C, 60 ~ 90 s Solder : Sn-3.0Ag-0.5Cu least 75% along the circumference Solder Temperature 245 ± 5 °C of the immersed part. Immersion Time : 2 ± 0.5 seconds 1.6±0.8mm MoltenSolder 7.5 Resistance to Meet Table 1. Flux : Ethanol solution of rosin, 25(wt)% soldering heat Pre-heat : 150 ± 10 °C, 60 ~ 90 s Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 270 ± 10 °C Immersion Time : 10s (+ 2s , - 0s) Then measure values after exposure in the room condition for 24 to 48 hours. 7.6 Resistance to Solder : Sn-3.0Ag-0.5Cu soldering iron Tip Temperature : 350 ± 10 °C Time : 4 ± 1 s Then measure values after exposure in the room condition for 24 to 48 hours. 8. Environmental Performance No. Item Specification Test Method 8.1 Temperature Meet Table 1. 1 Cycle Cycle 1 step : - 30 °C (+ 0°C , - 3°C) / 30 minutes 2 step : Room Temperature / within 5 minutes. 3 step : + 85 °C (+ 3°C , - 0°C) / 30 minutes 4 step : Room Temperature / within 5 minutes. Total of 10 cycle Then measured after exposure in the room condition for 24 to 48 hours. 8.2 Humidity Life Temperature : 40 ± 2 °C Humidity : 95 %(RH) Rated Voltage : 50 V(DC) Time : 500 h (+ 24h , - 0h) Then measured after exposure in the room condition for 4 to 24 hours. 8.3 Heat Life Temperature : 85 ± 2 °C Voltage : Rated Voltage  2 Time : 1000 h (+ 48h , - 0h) Then measured after exposure in the room condition for 24 to 48 hours. MURATA MFG CO.,LTD.

Spec. No. JENF243H-0006H-01 R eference Only P 4/ 7 9. Specification of Packaging 9.1.Packing Quantity Individual packaging 100pcs 9.2. Packing Method Styrene foam which have 50 pcs of the stuck products on are placed in an Individual packaging as 2 steps. A quantity in an Outer packaging is depending on a quantity of an order. In some cases , omit the Buffer material and/or Currugated cardboard. 9.3. Marking of packaging (1) Individual packaing The following items shall be marked on a label and the label is stuck on the Individual packaing. Customer part number, MURATA part number, Inspection number(1), RoHS discrimination(2), Quantity, etc ・1) « Expression of Inspection No. » □□ OOOO  (1) (2) (3) (1) Factory Code (2) Date First digit : Year / Last digit of year Second digit : Month / Jan. to Sep.  1 to 9, Oct. to Dec. O,N,D Third, Fourth digit : Day (3) Serial No. ・2) « Expression of RoHS discrimination » ROHS – Y (△) (1) (2) (1) RoHS regulation conformity parts. (2) MURATA classification number (2) Marking for Outside package The following items shall be marked on a label and the label is stuck on the outside package. Customer name, Purchasing Order Number, Customer Part Number, MURATA part number, RoHS discrimination(2) , Quantity , etc 9.4 Specification of Outer Case (ex.) Outer Case Dimensions Standard Individual (mm) package Quantity Label W D H in Outer Case H 265 89 118 5 Above Outer Case size is typical. It depends on a quantity of an order. D W MURATA MFG CO.,LTD.

Spec. No. JENF243H-0006H-01 R eference Only P 5/ 7 10. ! Caution Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party’s life,body or property. (1)Aircraft equipment (2)Aerospace equipment (3)Undersea equipment (4)Power plant control equipment (5)Medical equipment (6)Transportation equipment(automobiles,trains,ships,etc.) (7)Traffic signal equipment (8)Disaster prevention / crime prevention equipment (9)Data-processing equipment (10)Applications of similar complexity or with reliability requirements comparable to the applications listed in the above 11. Notice 11.1. Using the block type EMIFIL® (BNX) effectively This product effectively prevents undesired radiation 【 P.C. BOARD PATTERNS 】 and external noise from going out / entering the circuit by grounding the high frequency components which Use a bilateral P.C.board. Insert the BNX into the P.C.board until cause noise problem. Therefore, grouding condition may 　 the root of the terminal is secured. then solder. affect on the performance of the filter and following attentions should be paid for effective use. 　(1) COMPONENT SIDE VIEW (2) BOTTOM VIEW (1) Design maximized grounding area in the P.C. board, and grounding pattern for all the grounding terminals of PSG B B PSG the product to be connected.(Recommended to use our recommendation in this spec.) (2) Minimize the distance between ground of the P.C. PSG B B PSG board and the ground plate of the product. (Recommended to use through-hole connection between grounding area both of component side and CG CG CG CG bottom side. CG CB CB CG (3) Insert the terminals into the holes on P.C. board completely. Shield plate (4) Don’t connect PSG terminal with CG terminal Copper foil pattern directly. (See the item 4. TERMINAL LAYOUT) 11.2. Self-heating Though this product has a large rated current, the localized self-heating may be caused depending on soldering 【Recommendation land pattern】 conditions. To avoid this,following attention should be paid. 3.2 3.2 (1) Use P.C. board with our recommendation on hole Through holes φ1.2 diameter / land pattern dimensions, mentioned in the right B PSG hand drawing, especially for 4 terminals which pass current. (2)Solder the terminals to the P.C.board with solder-cover 2.5 area at least 90%. Otherwise, excess self-heating at connection between terminals and P.C. board may lead to CG CG 2.5 smoke and / or fire of the product even when operating at rated current. CB CG (3)After installing this product in your product, please make sure of the self-heating with the rated current. 3.2 （mm） 2.5 5.0 Copper foil pattern 7.5 MURATA MFG CO.,LTD.

Spec. No. JENF243H-0006H-01 R eference Only P 6/ 7 11.3. Soldering (1) Flux, Solder · Rosin-based flux should be used. Do not use strong acidic flux with halide content exceeding 0.2(wt)% (chlorine conversion value.) · Use Sn-3.0Ag-0.5Cu solder. (2) Standard flow soldering profile. C) Pre-heating(inair) SolderingGrad(uinalaCiro)oling 300 (° SolderTemperature re 250 u 200 rat 150 150°C pe 100 Solder Soldering m e 50 Temperature Time T 250 ~ 260 °C 4 ~ 6 s 1minutesmin. SolderingTime (3) Resistance to soldering iron goes in the following condition that tip temperature is 350 °C max. and soldering time is 5 s max. (4) Products and the leads should not be subjected to any mechanical stress during soldering process. (and also while subjected to the equivalent high temperature.) 11.4. Cleaning Conditions Products shall be cleaned on the following conditions. (1) Cleaning temperature shall be limited to 60 °C max. (40 °C max. for IPA.) (2) Ultrasonic cleaning shall comply with the following conditions, with avoiding the resonance phenomenon at the mounted products and P.C.B. Power : 20W / l max. Frequency : 28kHz to 40kHz Time : 5 minutes max. (3) Cleaner 1.Cleaner · Isopropyl alcohol (IPA) 2.Aqueous agent · PINE ALPHA ST-100S (4) There shall be no residual flux and residual cleaner after cleaning. In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in order to remove the cleaner. (5) The surface of products may become dirty whitely after cleaning. But there is no deterioration on mechanical, electrical characteristics and reliability. (6) Other cleaning Please contact us. 11.5. Operating Environment (1) Do not use products in corrosve gases such as chlorine gas, acid or sulfide gas. (2) Do not use products in the environment where water, oil or organic solvents may adhere to product. MURATA MFG CO.,LTD.

Spec. No. JENF243H-0006H-01 R eference Only P 7/ 7 11.6. Storage condition (1) Storage period Use the products within 12 months after delivered. Solderability should be checked if this period is exceeded. (2) Storage environment condition · Products should be stored in the warehouse on the following conditions. Temperature : - 10 °C to + 40 °C Humidity : 15 % to 85% relative humidity No rapid change on temperature and humidity · Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability. ·Products should be stored on the palette for the prevention of the influence from humidity, dust and so on. ·Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on. (3) Delivery Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. 12. ! Notes (1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2) You are requested not to use our product deviating from the reference specifications. (3) The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG CO.,LTD.