12 11 10 9 8 7 6 5 4 3 2 1 2.50 H H .098 1.30 .051 3.10 .122 1.00 0.20 ± .039 .008 ± G G ISOMETRIC VIEW (SCALE 4:1) 0.50 MAX. CUT-OFF F .020 IN CRIMP TOOLING. F 27.60 3.80 0.15 0.90 ± 1.087 .150 .006 .035 ± C 9 B E E 4.8 6.20 .189 .244 12AWG WIRE 8AWG TERMINAL 12AWG DOUBLE CRIMP (SEE NOTE 11) D D B C 12 & 10 AWG TERMINAL CONDUCTOR STRAIN RELIEF "HI-FLEX WIRE" (SEE NOTE 8) SHRINK TUBING CONDUCTOR CRIMP CRIMP AREA C C 8 AWG TERMINAL D A 8 AWG TERMINAL (SEE NOTE 8) (SEE NOTE 10) B B R. F R. C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE CURRENT REV DESC: REPLACES SD-42815-* E B MM/IN 8:1 GENERAL TOLERANCES (UNLESS SPECIFIED) MM INCH EC NO: 612616 FEMALE CRIMP TERMINAL, 12, 10 & 8AWG 4 PLACES ± ± DRWN: SGANGADHARDO 2019/02/22 MINIFIT SR. 3 PLACES ± ± 0.1 CHK'D: SGANGADHARDO 2019/02/22 2 PLACES ± 0.25 ± 0.16 APPR: ISHWARG 2019/02/25 PRODUCT CUSTOMER DRAWING A A 1 PLACE ± 0.4 ± INITIAL REVISION: DOCUMENT NUMBER DOC TYPE DOC PART REVISION SECTION B-B SECTION C-C 0 PLACES ± ± DRWN: RJF 1992/06/01 428150000-SD A1 PSD 000 (BACKGROUND OMMITED) ANGULAR TOL ± 0.5 ° APPR: RAS 1992/06/01 THIS DOCUMENT HAS BEEN RE-ISSUED BASED ON SD-42815-*, REV J. DRAFT WHERE APPLICABLE THIRD ANGLE PROJECTION DRAWING SERIES MATERIAL NUMBER CUSTOMER SHEET NUMBER DOCUMENT STATUS P1 RELEASE DATE 2019/02/25 05:13:52 MUST REMAIN C-SIZE 42815 SEE CHART GENERAL MARKET 1 OF 2 WITHIN DIMENSIONS FORMAT: Eng-lega-master-tb-prod-C12 11 10 9 8 7 6 5 4 3 2 1 REVISION: D DATE: 2018/01/18

12 11 10 9 8 7 6 5 4 3 2 1 MAX. INSULATION ITEM NUMBER WIRE RANGE DIM. A DIM. B DIM. C DIM. D DIM. E DIM. F PLATING STATUS DIAMETER 12 & 10 AWG 5.40 .60 6.10 .40 R 1.70 5.90 .60 6.60 .40 R 2.20 5.30 DIA. 428150011 ± ± ± ± H (5 & 6mm^2) [.213 .024] [.240 .016] [.067] [.232 .024] [.260 .016] [.087] [.209] PLANNED FOR H ± ± ± ± OVERALL TIN 5.83 .60 7.42 .40 R 1.70 6.00 .60 5.50 .40 R 2.20 6.60 DIA. OBSOLESCENCE 428150031 8 AWG ± ± ± ± [.229 .024] [.292 .016] [.067] [.236 .024] [.216 .016] [.087] [.260] ± ± ± ± 12 & 10 AWG 5.40 .60 6.10 .40 R 1.70 5.90 .60 6.60 .40 R 2.20 5.30 DIA. 428150012 ± ± ± ± (5 & 6mm^2) [.213 .024] [.240 .016] [.067] [.232 .024] [.260 .016] [.087] [.209] ± ± ± ± SELECT GOLD ACTIVE 5.83 .60 7.42 .40 R 1.70 6.00 .60 5.50 .40 R 2.20 6.60 DIA. 428150032 8 AWG ± ± ± ± [.229 .024] [.292 .016] [.067] [.236 .024] [.216 .016] [.087] [.260] ± ± ± ± 12 & 10 AWG 5.40 .60 6.10 .40 R 1.70 5.90 .60 6.60 .40 R 2.20 5.30 DIA. G 428150114 ± ± ± ± G (5 & 6mm^2) [.213 .024] [.240 .016] [.067] [.232 .024] [.260 .016] [.087] [.209] ± ± ± ± SELECT SILVER ACTIVE 5.83 .60 7.42 .40 R 1.70 6.00 .60 5.50 .40 R 2.20 6.60 DIA. 428150134 8 AWG ± ± ± ± [.229 .024] [.292 .016] [.067] [.236 .024] [.216 .016] [.087] [.260] ± ± ± ± F F NOTES: 1) MATERIAL: COPPER ALLOY 151, .020/(.50) THICK. 2) PLATING: 1 = .000100/(.00254) MIN. *TIN OVER E E .000050/(.00127) MIN. NICKEL. 2 = .000030/(.00076) MIN. SELECT GOLD IN CONTACT AREA. .000100/(.00254) MIN. SELECT *TIN ON SOLDER TAILS OVER .000050/(.00127) MIN. NICKEL. 4 = .000100/(.00254) MIN. SELECT SILVER IN CONTACT AREA .000100/(.00254) MIN. SELECT TIN ON SOLDER TAILS OVER .000050/(.00127) MIN. NICKEL. 3) PRODUCT SPEC.: PS-42815-001 D D 4) PACKAGING INFORMATION: PK-42815-001. 5) PART IS DESIGNED IN METRIC. 6) TERMINALS FOR USE WITH STRANDED WIRE ONLY. 7) ITEM NUMBERS PRECEEDED BY AN "X" IN THE CHART ARE NOT AVAILABLE. 8) THE 8 AWG TERMINAL HAS NO INSULATION CRIMP. THE SECONDARY CRIMP SECTION ACTS AS A STRAIN RELIEF ON THE BARE CONDUCTOR ONLY. SEE MOLEX CRIMP SPECIFICATION FOR DETAILS. 9 AFTER CRIMPING, THIS DIMENSION IS .140/(3.55) MINIMUM. C C 10) WHEN USING THE 8 AWG TERMINAL WITH "SUPERFLEX WIRE", MOLEX STRONGLY RECOMMENDS THAT THE APPROPRIATELY RATED HEAT SHRINK INSULATION BE APPLIED OVER THE WIRE INSULAITON AND CRIMP AREA, AS SHOWN, TO MINIMIZE WIRE INSULATION CREEPAGE OUTSIDE OF HOUSING. 11) THE 8AWG TERMINAL WILL ALSO ACCOMODATE 2 12AWG WIRES SEE CRIMP SPEC FOR DETAILS. 12) PARTS CONFORM TO CLASS 'B' REQUIREMENT OF COSMETIC SPEC B PS-45499-002. B 13) FOR PLATING OPTION 2 SEE NOTE 2 (OVERALL TIN PLATED PARTS), THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FOR APPLICATIONS INVOLVING VIBRATION AND/OR THERMAL CYCLING, DIMENSION UNITS SCALE CURRENT REV DESC: REPLACES SD-42815-* MOLEX STRONGLY RECOMMENDS TO USE NYE LUBRICANT, MM/IN 1:1 NYOGEL 760G LUBRICANT ON THE MATING AREA, GENERAL TOLERANCES AFTER THE TERMINALS ARE INSERTED INTO THE HOUSING, (UNLESS SPECIFIED) MM INCH EC NO: 612616 FEMALE CRIMP TERMINAL, 12, 10 & 8AWG REFER AS-42815-001 FOR ADDITIONAL INFORMATION. 4 PLACES ± ± DRWN: SGANGADHARDO 2019/02/22 MINIFIT SR. 14) THIS DRAWING REPLACES SD-42815-* REV. J AND 428150000 REV. A. 3 PLACES ± ± 0.1 CHK'D: SGANGADHARDO 2019/02/22 2 PLACES ± 0.25 ± 0.16 APPR: ISHWARG 2019/02/25 PRODUCT CUSTOMER DRAWING A A 1 PLACE ± 0.4 ± INITIAL REVISION: DOCUMENT NUMBER DOC TYPE DOC PART REVISION 0 PLACES ± ± DRWN: RJF 1992/06/01 428150000-SD A1 PSD 000 ANGULAR TOL ± 0.5 ° APPR: RAS 1992/06/01 DRAFT WHERE APPLICABLE THIRD ANGLE PROJECTION DRAWING SERIES MATERIAL NUMBER CUSTOMER SHEET NUMBER DOCUMENT STATUS P1 RELEASE DATE 2019/02/25 05:13:52 MUST REMAIN C-SIZE 42815 SEE CHART GENERAL MARKET 2 OF 2 WITHIN DIMENSIONS FORMAT: Eng-lega-master-tb-prod-C12 11 10 9 8 7 6 5 4 3 2 1 REVISION: D DATE: 2018/01/18